Search Documents

By F. Nava-Alonso, E. Pérez-García, A. Uribe-Salas, J. C. Fuentes-Aceituno, A. A. González-Ibarra, E. N. Castillo-Ventureño

"Precious metals cannot easily be recovered from tellurides by the standard cyanidation process. This work assesses the cyanidation of synthetic samples of precious metals tellurides and explores some alternatives for the leaching of these species (i.e. cyanidation in presence of lead nitrate and thiosulfate leaching). For this purpose, three chemical systems were studied: (1) cyanidation of silver telluride and the effect of lead (II) nitrate addition, (2) cyanidation at high alkalinity and high cyanide concentration of a gold-gold telluride sample containing tellurium and tellurium dioxide, and (3) thiosulfate leaching of silver telluride employing cupric sulfate as oxidant and EDTA as complexing agent for copper. Results showed that standard cyanidation dissolves 10.5% of silver from silver telluride in six hours, while with the addition of 100 mg/L lead increased the silver dissolution up to 100% in the same time. The standard cyanidation of the gold-gold telluride sample dissolves only metallic gold in six hours, while when cyanide concentration and pH were increased, gold and gold telluride were simultaneously dissolved. Finally, thiosulfate leaching dissolves 43.1% of silver from silver telluride in six hours.INTRODUCTION Precious metals tellurides are classified as refractory ores due to the difficulties associated with processing them by the standard cyanidation method. The increasing presence of gold/silver tellurides in some deposits around the world, specifically in Sonora, Mexico, requires new approaches to the cyanidation process, or the development of new leaching techniques. Treatments have been proposed for the recovery of gold and silver from their tellurides, including roasting, preoxidation, cyanidation with lead nitrate, and the use of leaching agents other than cyanide (Zhang, et al., 2010; Ellis and Deschenes, 2016). This work presents preliminary results of three options to recover precious metals from pure tellurides: the cyanidation of gold telluride at high cyanide concentration and high alkalinity, the addition of lead nitrate to the standard cyanidation process, and the use of sodium thiosulfate as leaching reagent."

Jan 1, 2017

By John L. Lamont, Walter Crafts

SELECTION of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of hardenability,1 as-quenched hardness,2,3 and tempered tensile strength.4 Ductility and toughness may also be estimated if the steel is completely hardened on quenching,5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In fine-grained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accompanied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to 4 in. in diameter. PROCEDURE The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1o30, 1040, 1340, 3310, 3316, 4320, 4330, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 9310, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.35. The bars were tempered as follows: ½ in., I in., and I 5/8 in., 2 hr; 2 ½ in., 3 hr; 4 in., 5 hr. All bars were air-cooled from the tempering tem-

Jan 1, 1947

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By Christopher R. Winter

Mining companies have sharpened their refocus on their tailings management strategies in recent years. Mining companies with tailings storage facilities that use the upstream construction method have been challenged to track the evolution of industry standards, assess risks, revise design, and communicate design revisions with regulators. While many aspects of best practices and industry standards have evolved in recent years as an attribute of continual improvement, the controlling standard in the design of many upstream dams is understanding the foundational strengths of hydraulically deposited tailings. Following best practices and industry standards, Hibbing Taconite Company managed by Cleveland-Cliffs, began the re-evaluation of foundation strengths underlying a system of upstream dams at the company’s iron ore mine tailings storage facility in northern Minnesota. Initial steps in the re-evaluation require reanalysis of design parameters and recommendations by the Engineer of Record to the Owner, which was followed by a series of meetings with the Technical Review Board to determine an initial path forward. Once a path forward and preliminary design parameters were determined, the Owner engaged with the State Dam Safety Engineer to discuss and seek approval of the plan. With continuous regulatory engagement throughout the process, further refinement of the design parameters for the hydraulically-placed tailings foundations underlying upstream dams began with field and lab geotechnical investigations. Following a review of risk assessments and trigger actions response plans, Hibbing Taconite revised its tailings storage facility operating plans and budget for the coming years. Based on the findings of the re-evaluation, reanalysis, and refinement of parameters, a paradigm shift was realized with the hydraulically placed tailings foundation strengths underlying the upstream system of dams. This paper explores the path that the Hibbing Taconite Company followed to understand the paradigm shift and construct downstream improvements. The plan involved tailings re-characterization, dam design revisions, operating plan reconciliation, budget revisions, wetland permitting, dam safety permit amendments, storm water prevention plans, borrow materials studies, new concrete decant structures and the pursuit to recognize and be consistent with industry standards.

Feb 1, 2024

By Waldemar Dyrssen

I CANNOT agree with the results obtained by the committee. The gas obtained per pound of coal is too high in calorific value and the amount of gas is too large. It should require about 190 cu. ft. of oxygen per 1000 cu. ft. of gas and not 75.14 cu. ft. as is given on page 35 of the report, or about 2.5 as much. Calculating the calorific value per pound of coal from the coal analysis given on page 34, according to Dulong's formula, the gross and net calorific heat are about 12,890 and 12,430 B.t.u., respectively, which is about 18,600 and 17,900 B.t.u., respectively, per pound of carbon in the coal. This is an unusually high figure, as ordinary bituminous coal has less than 18,000 gross B.t.u. per pound of carbon. Assuming, however, that the calorific values calculated are correct, the following results are obtained. On page 35, the net calorific heat in the gas per pound of coal is given as 12,856 B.t.u. and calculation for the gross value shows it to be about 13,950; in other words, the gas contains (13,950 - 12,890) ÷ 12,890 = 8.2 per cent. more heat than the coal on a gross basis and (12,856 - 12,430) ÷ 12,430 = 3.4 per cent. more on a net basis. The calculated amount of carbon in this gas per pound of coal gasified is about 0.688 lb., or nearly the same as in the coal (0.6972) and the gross and net calorific heat per pound of carbon in the gas are 20,300 and 18,710 B.t.u. which are 9.1 and 4.5 per cent. more than for the carbon in the coal. These calculations show that the results given in the report cannot be correct. There must always be some heat losses in the gasification of coal, in radiation from the producer, and in sensible heat in the gas; there must be some loss of carbon in ashes and in soot, and there are always tarry vapors in the gases that are condensed and do not appear in the fixed gases. From the excessive heat in gas per pound of carbon contained therein, it can also be concluded that the percentage of hydrogen in the gas is too high, from which it follows that the moisture decomposed is too high and that more free oxygen must be used.

Jan 11, 1924

By B. A. Cheadle, C. E. Ells

The ovienlalion of hexagonal a-zirconium crystals in cold-drawn Zircaloy-2 tubes and in both as-extruded and heat-treated Zr-2.5 wt pcl ND tubes has been rrleasured using the inverse Pole - figure technique. Uniaxial tensile tests hare shown the Zil-caloy-2 lubes to hare highly anisotropic delovmation behavior whereas heat-treated Zr-2.5 wt pet Nb tubes are nearly isotropic. The differences in deformation behavior are esbloilred from the observed textures of the tubes and the deformation systems known to oberate in Zircnloy,-3. Tlze vcsults lead to an explanation of the high effective strain observed fov the Zircaloy-2 tubes as colrzpared to heat-treated Zr-2.5 wt pet Nb tubes in restrained end burst tests at 280° to 300°C. THE Zr-2.5 wt pct Nb alloy. when heat-treated by quenching from temperatures slightly below the (a + p)/P phase boundary and subsequently aged at 500°C, has tensile strengths about 50 pct greater than those of 20 pct cold-worked Zircaloy-2.1 There is. therefore, considerable economic incentive to replace Zircaloy-2 with the heat-treated alloy in some in-reactor applications. notably for pressure tubes, where strength is a prime consideration. However, when tubes of Zr-2.5 wt pct Nb fabricated by extrusion and drawing prior to heat treatment were subjected to restrained end-burst tests at 300 °C. the circumferential expansion at failure1 was only 10 pct that of cold-drawn Zircaloy-2 tubes in similar tests,2 Table I. This result was not predicted from uniaxial tensile tests in which the ductilities of the two materials were quite similar.' The detailed requirement for ductility in pressure vessels has not yet been worked out. and comparison of the relative merits of cold-worked Zircaloy-2 and heat-treated Zr-2.5 wt pct Nb is further complicated by the irradiation-induced loss of ductility and hydrogen pickup each will undergo from reactor operation.1,2 Nevertheless. the lower circumferential expansion of the Zr-2.5 wt pct Nb tubes raised serious doubts on the advisability of their use as pressure vessels. For this reason, an investigation to determine the cause for different ductilities of the two types of tubes was initiated. From a study of uniaxial tensile properties and crystallographic orientation it has been found that the fracture ductilities observed in the burst tests can be related directly to the crystallographic ori-

Jan 1, 1965

By A. J. Opinsky, J. L. Orehotsky, L. L. Seigle

TUNGSTEN incandescent lamp filaments possess a typical structure of elongated crystals generated upon heating the silica-alumina doped wire rapidly to 2200°C or above.&apos; It is known that these very long grains exhibit a preferred orientation, but there is disagreement in the literature about the direction. Rosi,2 and later Rieck; reported that the <135> direction of the large grains in doped wire tends to be parallel to the wire axis, but other investigators have reported that <110> is the preferred direction. Some further investigation of the orientations of large grains in tungsten wire is reported in the following. In the first series of experiments, 6-in. lengths of wire were heated rapidly in a bell jar. Current was passed through the wires and within 15 sec the wires had reached the grain coarsening temperature. 2 min was the annealing time. Wires were heated in hydrogen, nitrogen, and vacuum. Later, wires were heated in an evacuated tube furnace in which the tube was brought from 1000°C to the operating temperature within 25 sec and held 5 min at temperature. Temperatures were measured with an optical pyrometer. After heating, the wires were electro polished and etched, and the orientations of the large grains determined by the Laue back-reflection technique. Most of the experiments were carried out on a single spool of 5-mil silica-alumina doped wire, but a few tests were made with 5-mil thoriated tungsten wire and 10-mil undoped wire. 5-mil silica-alumina doped wires were reduced to smaller diameters by electropolishing for one series of experiments. Orientations of the large grains in silica-alumina doped wire heated in various atmospheres are presented in Figs. 1 and 2 as plots of the direction of the wire axis relative to the cube axes of the crystals. For most of the conditions studied, the preferred orientation cannot be described as a single direction, but the points might be said to group themselves about the arc passing through <110> and <113>. This arc is the trace of the (211) planes and contains the <135> and <124 as well as <011> directions previously observed by other investigators. The preferred orientation of large crystals in silica-alumina doped tungsten wire might be most generally described, therefore, by stating that a (211 ) tends to be parallel to the wire axis. This is true also for wires reduced in diameter by etching and furnace heated, Fig. 2, i.e., the recrystallization texture is apparently unchanged upon removal of the outer layers and substantially independent of the temperature gradient within the wire.

Jan 1, 1962

By R. L. Wise

Heat content studies were conducted on burned shale, spent shale, and three grades of raw oil shale from the Green River Formation. Corrections were made for product enthalpies. The results were compared with previous work, indicating good agreement below retorting temperatures, but some differences at retorting temperatures. A general equation was developed relating heat content to oil-shale grade and temperature.

Jan 1, 1971

By Peter Moser, Thoma Oberndorfer

"Within the research project “Mine Development” (Fettweis and Moser, 1990) a PC-based mine database has been built up since 1991 and so far includes detailed technical and economic data of about 150 under-ground hardrock mines in industrialized countries worldwide. These data represent about 50% of the underground hardrock mines in west and central Europe, Scandinavia, United States, Canada and Australia (Fig. 1). The mining operations included in the database have been visited directly and analyzed with respect to their deposit conditions, their general design and layout and also their operational and economic performance.The main aim of the Mine Database is to make a contribution to an improved planning of new underground hardrock mines. An analysis of current mine planning practices shows, that both personnel and company experience is still a dominant factor in planning new underground hardrock operations. Through the information included in the Mine Database the experience of a single per-son or company is supplemented by the experience of a wider group of people. The Mine Database makes the huge amount of experience that is available worldwide in the field of under-ground mining accessible for new mining projects. From that a contribution to a more reliable mine planning procedure based on the performance of existing mining operations is expected.In addition to its use in planning new mining operations, the Mine Database can con-tribute to the exchange of technical data among different mining operations, especially on equipment performance, etc. Such an information service is offered by the Department of Mining Engineering & Mineral Economics in Leoben and is already being used by different mining companies. To respect proprietory information, company specific information is not released under any circumstances.The cost of building up the Mine Database, so far, is about US$500.000 — two thirds of which is labour, and one third, travel."

Jan 1, 1996

By Carsten Rühlemann, Thomas Kuhn, Cornelia Kriete

"Any economic calculation with respect to potential submarine mining activities requires reliable analytical data on the contents of valuable metals in these ores, including trace metals such as rare earth elements as well as Ti, Mo, V, Zr and Li. Due to the very special matrix of ferromanganese nodules (30% manganese oxides, 10-20% iron oxides, silicates; see Kuhn et al., this volume), their geochemical analyses pose a real challenge. Available ferromanganese nodules reference materials, e.g., NOD-P1 and A1, JMn-1, GBW07249, SDO-4 to -7 and NM2388, generally have only a few certified values for trace elements. Published data for these reference materials, collected in the GeoReM database (http://georem.mpch-mainz.gwdg.de/) are either rare for high technology metals or widely scattered for certain elements, especially the PGEs. Since most of these materials were released in the 1990s, many analytical procedures have seen significant advancement.In order to facilitate analytical quality assurance during exploration and potential future mining activities, the German Federal Institute of Geosciences and Mineral Resources (BGR) has contracted the Central Geological Laboratory of Mongolia (CGL) to produce a certified reference material for nodule analytics. Certified reference materials provide the highest level of reliability in geo-analytical measurements currently available and the CGL has a long-term experience in producing geological reference materials. Recently, the CGL was accredited as a reference material producer according to ISO Guide 34 by the American organization ACLASS (Assured Calibration and Laboratory Accreditation Select Services). Furthermore, it has been accredited as a testing laboratory according to ISO 17025."

Sep 1, 2014

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Charles M. Pelanne

Without insulation we could not survive on this planet. This may sound like a self-serving statement but it is a fact. The blanket of air which surrounds us is a very effective insulating blanket, allowing some shortwave solar radiation to warm us during the day while retaining the longer infrared radiation at night. Our life on earth is very much dependent on materials performing an insulating function without being thought of as insulation, clothing, fur, window glass, the ice of an igloo etc. The mechanisms of heat transfer involved in these materials are analogous to those involved in engineered insulations - Engineered insulations are designed for maximum effectiveness for given conditions within the applicable retraints. Engineered insulations are very effective! As an illustration let us consider this graph (Figure 1). It represents: 1. The radiative heat transfer between two 1 foot2 (0.0932) radiantly black surfaces, one at 100F (38C) and the other at the temperature indicated on the bottom scale. This does not include the convective and conductive heat flow of the air, both of which are significant but small in comparison. 2. The heat transfer resulting from the placement of 1 inch (25.4 mm) of insulation [10 pcf (160 kg/m3) ceramic fiber] between these two plates.

Jan 1, 1976

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement&apos;s per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement&apos;s per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939

By Jamal Rostami, Tom Iseley, Saleh Behbahani

Tunnels and underground infrastructures assets, like all assets, deteriorate with time. At some point, they reach the end of their useful life. Therefore, frequent inspections, higher levels of maintenance, and rehabilitation are needed to address loss of life and safety concerns. The repair cost of tunnels will increase if maintenance of tunnels is not satisfactory and timely. Historically, tunnel inspections have primarily relied on visual and manual procedures. Due to their time-consuming nature and susceptibility to human error, there is a demand for alternative automated techniques that can enhance efficiency and reliability in tunnel inspection. By utilizing a tunnel scanning system, such as laser scanner and thermography, or photogrammetry system, tunnel inspection cost, time, and personnel can be reduced. The goal of this study is to utilize deep convolutional neural networks (CNNs) for automated identification of defects in tunnel lining inspection. This paper presents a framework to classify two types of defects in tunnel lining (water leakages and cracks) using CNNs. The CNNs were trained and tested using 4,608 images. The Precision, Recall, and F1 Score were each 99.6%, confirming the viability of this approach in the automated defect identification in tunnel lining.

Jun 23, 2024

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933