Search Documents

By Marcel M. Djivre

The paper will outline the methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. Also for Canadian mines the paper will suggest proposed criteria to be used at MTL for the evaluation of ropes used in "ultra-deep" single-lift shafts. Most of the methods and test procedures currently used at MTL were adopted during the revision of the CSA Standard G4, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage to be published most likely in year 2001. In this latest or sixth edition of CSA Standard G4, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The existing fifth edition of CSA Standard CAN/CSA -G4-92, which is intended for the manufacturing of new ropes, includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish.

May 1, 2001

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By Neely H. Bostick

The primary and secondary organic matter in sedimentary rocks changes markedly when it becomes heated as a consequence of thick sediment accumulation and normal geothermal gradients, high geothermal gradients, hydrothermal fluids, or igneous events. Contact zones adjacent to small igneous dikes allow sampling of a single sedimentary bed that has been exposed to temperatures in a range as great as 30-500°C. Dike-heated rocks are, therefore, good sites for research on thermal effects because variation of the original organic matter is minimal, the range of heating is great, and the history of rock heating in a dike zone is relatively well established. In rare cases, such as at the dike near Wolcott, Colorado, described in this paper, the rock samples are sufficiently unweathered to allow analysis of secondary bitumens generated by the heating. We show by optical microscopy, scanning and transmission electron microscopy, and geochemistry the kinds of solid organic constituents in sedimen¬tary rocks and in ore deposits and the effects of heating. The primary phytoclasts that make up kerogen In sedimentary rock and in some ore deposits (pollen, resin, charcoal, humified woody remains, etc.) change in ways that are familiar to coal specialists. Progressive loss of moisture and other volatile matter yields residual kerogen that Is relatively higher in carbon and lower In oxygen and hydrogen, and has greater molecular or polymer ordering. In our contact zone examples, atomic H/C ratios of kerogen decrease from 0.8 (one case from 1.4) to 0.4, the hydrogen index from Rock-Eval pyrolysis decreases from 70 to 5, and the transformation ratio from Rock-Eval pyrolysis increases from 0.06 to 0.5 with increased heating. The visible effects of heating seen by scanning electron microscopy and light microscopy include formation of vesicles and flow structure, the development of optical anisotropy and mesophase, change of color, and increase in the refractive index, absorption, and reflectance. Some of these changes In primary organic matter are observed also in secondary organic matter, for example, in solid bitumens in sedimentary gold ores or In lead-zinc deposits. Quantification of color or absorption changes is difficult because it Is hard to make thin sections of organic matter with uniform thickness. However, natural objects with uniform thickness can be used. We show the colors of pollen In rocks from the Salton geothermal field at temperatures ranging from 100 to 300°C, and of pollen heated in laboratory bombs from 150 to 400°C. Measurement of vitrinite reflectance is a practical way to quantify thermal changes of kerogen and minerals of most sedimentary rocks because vitrinite is fairly widespread In sedimentary rocks of Devonian age and younger. For example, the reflectance of vitrinite rises from the regional level, as low as 0.4 % Ro, to more than 5% Ro adjacent to dikes that cut sedimentary rock. This is equivalent to the rank change from subbituminous coal to extreme meta-anthracite. The rise is most abrupt near thin dikes, but when the distance from the igneous contact is expressed as a ratio of dike thickness the reflectance rise is similar for all dikes. Controlled heating of vitrinite-bearing rocks In the laboratory provides a means to assign known temperatures to vitrinite-reflectance values. The derived plots of temperature In dike contact zones have the same shape and level as those predicted by heat theory, and the temperature lines extend toward dike contact temperatures that are about half those of most magmas, as expected if the intrusions did not flow past the sedimentary rock for a long time. The globular submicroscopic structure of vitrinite and Its heterogeneity, which we show by means of transmission electron microscopy, pose some problems In selecting a uniform type of vitrinite for measurement of thermal changes. At present, routine reflectance values of vitrinite dispersed in rocks have a relative uncertainty as great as 10%. Thermally caused chemical changes in the primary kerogen, especially decrease in the oxygen and hydrogen contents, lead to formation of secondary products in the contact zone. The measured changes of secondary organic products in these rocks include formation of peaks In concentration of total extractable organic matter and in hydrocarbons, and in the saturated/aromatic hydrocarbon ratio over the interval where primary organic hydrogen decreases most rapidly--then destruction or expulsion of these products at high temperatures. The odd carbon-number predominance of the C25-C31 n-alkanes In samples far from the dike disappears by about 1.3% Ro whereas the 13C: 12C ratios of the saturated and aromatic hydrocarbons increase over most of the thermal range. The saturated aromatic hydrocarbon ratio at first increases, corresponding to thermal generation of saturated hydrocarbons, then decreases in the most altered samples. One use of organic petrography, in addition to identifying organic fades or thermal alteration, is recognition of sample contamination such as the solid organic additives used in some drilling muds which may contaminate geochemical samples.

Jan 1, 2013

By OÆBrien R. T

A small static bed was used to study the thermal cycles required for the heat hardening of pellets based on synthetic magnetite concentrates and a naturally fine hematite. This apparatus can be employed to yield broad process data for the design of a recuperative strand system operating on the magnetite concentrates.Various alternatives are given for a process to heat harden the hematite ore but a preference is given to the production of a self fluxing pellet. Bond types and general mineralogical structures are interpreted against the optimum firing cycle necessary to produce a defined quality of pellet.INTRODUCTIONThe work reported in this paper extends that on the "Heat Hardening of Artificial Magnetite Pellets", which was described at the International Symposium on Agglomeration, sponsored by the American Institute of Mining, Metallurgical and Petroleum Engineers at Philadelphia, U.S.A. in April 1961. Whereas that work was of a more basic nature, serving to illustrate the suitability of artificial magnetites with various admixtures, to the application of heat hardened pellets, on this occasion the aim is to illustrate the procedures which were used to establish the dimensions of commercial recuperative strands for Australian raw materials.The nature of the pellet feed, Le. relatively uniform spheres of + i in.-Yi6 in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas flows...

Jan 1, 1963

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By Robert T. DeGavre

INTRODUCTION The $645 million financing for Inco Ltd's Soroako nickel project in Indonesia not only represents a significant human achievement but also there are certain important lessons that can be derived from Inco's experience in financing the project. The paper will not present a technical assessment of the project since Inco Ltd. submitted a series of papers on this subject at the international Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979. BRIEF HISTORY OF THE SOROAKO PROJECT Table 1 summarizes the milestones achieved in the Soroako project and its financing. Exploration Phase A contract of Work was signed on July 27, 1968 by the Republic of Indonesia and F.T. International Nickel Indonesia (P.T. Inco) covering an extensive area of over 25,000 square miles on the two southeastern arms of the island of Sulawesi. The Contract provides that P.T. Inco has the sole responsibility for financing the project and determining the terms on which the financing should be obtained, that P.T. Inco has the right to receive and hold outside of Indonesia foreign exchange revenues and to freely dispose of such revenues, and that Indonesians have the right to purchase up to 20% of the equity of P.T. Inco over a period following start of production. P.T. Inco began field investigations in the Contract Area in August 1968. Preliminary reconnaissance sampling with portable drills broadly outlined areas of favorable laterite terrain which were then systematically sampled on surveyed grids. By early 1971 sufficient exploration work had been completed to indicate that the laterite deposits near Soroako could sustain a major nickel-producing plant (figure 1). Pilot plant studies in 1970 and 1971 at Inco's research station in Port Colborne, Ontario, using two bulk samples of Soroako ore material, also confirmed that the ore could be upgraded and treated for the recovery of its metal values. Feasibility Phase Encouraged by the results of its exploration program and pilot-plant work, Inco Ltd. commissioned Toyo Engineering Company of Japan in August 1971 to prepare a capital cost estimate for a relatively small nickel project called "Stage I". Stage I was to be a single-line pyrometallurqical process plant with an annual capacity of approximately 15,000 metric tons of nickel contained in 75% nickel sulphide matte (see Figure 2). Electric power was to be supplied by a thermal power station. It is important to recognize that Inco's strategy was to develop the Soroako ore deposits in several stages: first, construct a small project to gain experience and to reduce the initial capital outlay and then later expand in one or more steps to a much larger project to achieve maximum economies. The strategy reflected both Inco's financial position in 1971 as its sales and earning dropped sharply and the difficulties previously experienced by Inco in trying to launch in the late 1960's very large "greenfield" nickel projects in New Caledonia and Guatemala. Toyo's Project Development Study was completed. in January 1972. Based upon Toyo's cost estimate for physical facilities, Inco estimated the total capital cost of Stage I to be $115 million. For the next several months, Inco ran numerous in-house financial feasibility studies, using as inputs Toyo's cost estimate and the results of its exploration and pilot plant programs. In September 1972, Inco completed a project feasibility study which was based upon a capital cost estimate of $135 million. The feasibility study was immediately made available to potential partners and lenders. Partner Negotiations The Japanese nickel market had from the outset been central to Inco's planning for the Soroako project. That market had been growing dramatically at rates in excess of 20% per annum during the 1950's and 1960's. Japan had established, for rational security and other reasons, a domestic

Jan 1, 1985

By G Barla

In Europe, a major interest in the infrastructure and tunnelling fields is in the new crossings of Alps in the form of base tunnels, which are important components of the high-speed (for passengers)/high-capacity (for freight) Trans European railway corridors. These tunnels cross the mountain belt at the elevation of the main cities and basins located all around the Alps and are longer (up to 57 km) and deeper (up to 2500 m) than all tunnels constructed in the centuries before. The excavation of the first Alpine railway and road traffi c tunnels could in general be carried out successfully by conventional excavation methods. With the great lengths of the new base tunnels, mechanised excavation by using tunnel boring machines (TBMs) is imperative as it contributes significantly to savings in construction time and costs. Questions are however posed on the adoption of such a systematic tunnel construction method given the severe ground conditions which are some time anticipated along the tunnel alignment, with possible major geological hazards such as water inflow in heterogeneous fractured or karstifi ed rock masses, stress-induced tensile failure of hard rocks, and plastic shear failure and squeezing of weak rocks, etc. This lecture is to briefly review the current state-of-the-art in the understanding and modelling of two such critical hazards as spalling/bursting and squeezing ground behaviour. With the present interest in the design of mechanised tunnelling with TBMs in such conditions, the complex interaction between the rock mass, the tunnel machine and its system components, and the tunnel support is studied in detail by numerical modelling. The research and development efforts presently underway with the intention to provide the designer with a novel three-dimensional (3D) simulator of mechanised tunnel excavation are presented. Case examples are discussed with reference to the Lyon-Turin Base Tunnel design.

Mar 8, 2011

By Han Zhao, FENGLIANG WU, Tong Wang

Calibrating an entire mine ventilation network model from survey data has long been considered a challenging and sometimes impractical task. This paper proposes a solution to this issue with the development of a quadratic programming optimization model. The optimization model takes the minimum modification of input resistances as the objective function, uses the mesh pressure equations as equality constraints, and incorporates the lower limits of airway resistances as inequality constraints. A two-step method is developed to solve the model, which includes finding an initial feasible solution and iteratively solving the final solution using the active set method. A computer program has been developed to implement the optimization model. To demonstrate its practicality, a study case using a 35-branch ventilation network is presented, which indicates that the solution process converges after only 57 iterations, a significant improvement over the times of trial and error, which could reach 3.4 × 1010 for the worst-case scenario. Additionally, it is shown that considering only the equality constraints results in negative resistances, while incorporating the lower limits of resistance ensures that the corrected resistances are within a reasonable range. Using the resistance corrected by the optimal model to simulate the ventilation system via traditional methods generates quantities and fan pressures that perfectly match the measured values, eliminating the tedious process of manually adjusting airway resistances repeatedly.

Jan 13, 2024

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By Shuyu Qin, Shujiang Sun, Jingfu Zhao

The three key parameters of mine fires are local airflow velocity, temperature and oxygen concentration. According to the theories of seepage in porous media, heat transfer and heat dispersion, mathematical models were constructed based on the three parameters. The models can be used for early prediction of mine fires and for estimation of the level of spontaneous combustion. Proper use of the models can assist in preventing and controlling mine fires. KEY WORDS: airflow velocity, temperature, oxygen concentration, numerical modelling, mine fire prediction.

Jan 1, 1993

By David W. Lillie, Pier A. Abetti

This paper reports on a study of the impact of fast growing new technologies on the market for copper over the next 15 to 20 years. The greatest threat is clearly the inroads of fiber optics on the traditional market for copper in communication cable. Opportunity areas identified include heat pumps, solar power and heat, desalination, electric vehicles and others. The overall impact of new technologies on copper is expected to be modestly positive if adequately encouraged by effective R&D.

Jan 1, 1986

By D. C. Panigrahi

The paper presents the development of a thermodynamic based network analysis model. It uses transient heat flow algorithm for computing the heat flow from strata and predicts the environmental condition in different branches of the network. Along with the environmental condition, the mass flow distribution in network is computed by using nodal pressure method based on linear theory approach. The algorithm has been coded using object oriented programming approach and it has been validated in actual field condition. The correlation is satisfactory.

Jan 1, 1997

By Youzhen Zhang

The drilling boom is the key component of a roof bolter, and it has significant impact on the performance, safety, and reliability of the overall working device. In this paper, the experimental modal parameters of a drilling boom at low frequencies are identified with the Laplace wavelet correlation filtering method. Based on the obtained experimental parameters, a finite element model of the drilling boom is revised using an optimization algorithm to improve its accuracy. The dynamics of the drilling boom are analyzed through its modal and harmonic response. As a result, an improvement for the drilling boom is proposed to fix the weak links and enhance the dynamic performance.

Jan 1, 2012

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed.The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences. These were...

Jan 1, 1970

By Taehong Kim

An accurate and reliable prediction of Tunnel Boring Machine (TBM) performances, in terms of Rate of Penetration (ROP), utilization (U), and cutter wear rate, is a critical element in the successful planning and execution of mechanical tunneling project. Three open hard rock TBM projects were studied to establish possible trends and correlations between rock mass properties and machine performance. Based on this analysis and literature survey, three geological parameters, including RQD, RMR, and groundwater inflow rate, were identified as having the greatest impact on TBM utilization level. Rate of Penetration (ROP) and cutter wear rate were also correlated with fracture spacing, alpha angle, and Cerchar Abrasivity Index (CAI).

Jan 1, 2008