Search Documents

By John Porter

(Cleveland Meeting, October, 1912.) Iv taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Effeciency-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-records, clue to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost, sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences.

Jan 4, 1913

By John Jermain Porter

In taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Efficiencj-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-recorcis, due to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost-sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences. Efficiency-records supply this need. They compare actual

Jan 1, 1913

By Frederic P. Dewey

This old and well-known method of determining silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, and because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a detemination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained. For this determination 1,115 mg. of standard metal are weighed and transferred to a glass-stoppered bottle, the metal is dissolved in nitric acid, and 100 cc. of a standard solution of NaCl run in. The bottle is then vigorously shaken and a measured portion of a decimal salt solution added, and again shaken, if necessary. These operations are repeated until the silver is precipitated. Standard metal being 900 fine, 1,115 mg. should carry 1,003.5 mg. of silver, which is a convenient figure to work with.

Jan 1, 1914

By George Frederick Kunz

The manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg.; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a ki1ogram. He also called attention to the fact that while this would depreciate the present diamoiid carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.' The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sévres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3 The general adoption of a uniform standard for dealings in pre-

Jan 1, 1914

By E. H. Jr. Dix

THE success of the Charpy impact test in the steel industry has led those interested in aluminum alloys to investigate the possible applica¬tion of this test to aluminum and its alloys. In this paper are set forth the results of a few preliminary tests made at the Lynite Laboratories of the Aluminum Manufactures, Inc. In order to study more thor-oughly the significance of the Charpy test, slow-bending tests have been made duplicating the arrangement of the impact machine. Tests have been made on both notched and unnotched specimens of a series of copper-aluminum alloys. APPARATUS The standard American-made Charpy impact machine delivering a blow of over 200 ft.-lb. was- much too large to test aluminum-alloy specimens of the same type used for steel, so that it was necessary either to adopt a larger specimen or to have a special light-weight hammer made. Since there is no known relation between specimens of different sizes, even though geometrically similar, it was decided to adhere to the 10 by 10 mm. specimen. Accordingly, Sauveur and Boylston, the American makers of the machine, were asked to construct a special light-weight pendulum adapted to their standard machine, this pendulum to have one-tenth the capacity of the standard. The writer wishes here to acknowledge his indebtedness to Mr. H. M. Boylston for the personal interest and care exercised in constructing this pendulum. The machine with, the light-weight hammer in place is shown in Fig. 1. It is mounted on a concrete foundation with the concrete covering the flange on the base of the machine. Vibration is further prevented by four 5/8 -in. (15.8 mm.) foundation bolts. The large standard hammer shown against the wall was also used for some of the unnotched bars that requited more than 20 ft.-lb. to rupture.

Jan 4, 1920

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992

By Liangying Wen, Feng Xia, Chenguang Bai

"The situation of the Ti-V-Magnetite samples reduced with microwave has been investigated in laboratory. Firstly, the paper focuses on the heating behaviors of vanadium-titanium magnetite and characteristics of carbothermic reduction of V-Ti-magnetite in the microwave field. The effect of concentrate's size, quality on heating behaviors and reduction processes were researched. Results show that microwave heating may be a new heating resource replace of carbonic combustion reaction in reducing reaction. When the allocation of carbon is (16.7-30)%, carbothermic reduction of V-Ti-magnetite in the microwave field can proceed; with the increasing of carbon mixed, the metallization rate increases; and Fe, V can be reduced from their oxides in the microwave field; Titanic low oxide can be reduced from TiO2.1. IntroductionThe resource of Ti-V-Magnetite is abundant in the western area of Panzhihua in China, so far a mineral deposit of 4.64 billion tons have been proved up, it contains 14.75 million tons of V2O S which accounted for 87% of the vanadium and 5.93 hundred million tons of TiO2 accounted for 94% of the titanium resource respectively in China. The previous study proved that the major composition of mineral of the Ti-V-magnetite are Ti-magnetite, limonite, iron spinel, magnesium spinel etc, and the main elements of the Ti-V-magnetite in this area are Fe, Ti, V, Cr, Co, Ni, Ga, Sc etc[1] Due to the restrict of the BF-BOF process technical, during the smelting of the iron, the level of extracting the vanadium, titanium as well as other metal elements is limited. This results serious wasting of resources. To develop a new reduction process of Ti-V-magnetite is on the agenda, the microwave assistant reduction could meets this need, based on its characteristic of easy controlling of heating rate. To make use of the microwave energy to substitute the released heat sources of carbon combustion with air, use the solid phase state reduction at a relative lower temperature, make the beneficial element in Ti-V-magnetite transferred into the metal phase, then separated from the impurity. It is well worth to point out that once the microwave based reduction method has its industrial scale, it will take an outstanding position by its less release of carbon dioxide. This new environment-friendly process will play a vital role in the development of social industry and economy."

Jan 1, 2008

By Nicholas Zabaras, Deep Samanta

"Solidification of metal aluminum and aluminum alloys is modeled on uneven surfaces characterized by sinusoidal curves. Wavelengths and amplitudes of these sinusoidal surfaces are varied to study their effects on processes like solidification, macro-segregation and inverse segregation. Solidification and macro-segregation are modeled using a slightly modified form of a stabilized finite element method developed recently to model high Rayleigh number solidification and porous media flows. For pure metal solidification, the effect of varying amplitudes and wavelengths is observed in heat transfer, fluid-flow ~nd phase change processes. The relative importance of shrinkage driven flow and solutal convection on the redistribution of solute for an alloy solidifying in a rectangular cavity is compared. The analysis is then extended by modifying one of the surfaces to a sinusoid. In this case the effects of varying amplitudes and wavelengths are studied in heat transfer, fluid flow, phase change, macro-segregation and inverse segregation processes.1 IntroductionTransport phenomenon during solidification of alloys is a major cause ofcasting defects such as segregation, micro-voids, hot tears, porosity, internal and surface cracks. Heat flow across metal and mold surfaces directly affects the phase change process and plays an important role in determining freezing conditions within the metal. In alloys, natural convection and shrinkage play an important role in determining the final solute redistribution, macrosegregation and evolution of solid macromorphology. Surface unevenness plays an important role during the early stages of solidification. It influences the heat transfer rate and fluid flow in the melt, which in turn affect the morphology and shape of the solid-liquid interface. The effect of surface unevenness on solute redistribution is important during solidification of alloys, where solute driven flow in the mushy zone is prominent. Thevik and Mo in [7] and [8] used a one dimensional model for studying surface segregation and macrosegregation in alloys under the influence of exudation and solidification shrinkage. Air-gap formation in their model was expressed through a variable convective heat transfer coefficient at the boundary. Tsai et al. in [3] and [4] have modeled macrosegregation in an aluminum-copper alloy driven by shrinkage and solutal convection. They used a single domain model based on mixture theory and solved the transport equations using finite difference methods. Our aim is to model solidification of aluminum followed by macrosegregation and inverse segregation in aluminum-copper alloys on uneven surfaces by finite element methods. These surfaces are modeled as sinusoids characterized by amplitudes, ?s and wavelengths, As, By varying As and ?s, changes in heat transfer, fluid flow, phase-change and macrosegregation are studied."

Jan 1, 2004

By W. R. Marks

Computer-aided torsional analysis of grinding mill drives is defined and related to the mill design process. Equations of torsional dynamics are developed for general mechanical drives. Consideration is given three solution types - specifically the determination of undamped natural frequencies, the calculation of steady vibration amplitudes, and the prediction of transient torques during starting. Following a summary of the methods of calculating drive motor performance, the problem in making practical application of this theory are discussed. Experiences in both calculating and measuring the torsional loads on a large ball mill with dual synchronous motors are reviewed. Conclusions are drawn on the effectiveness of computer-aided torsional analysis for improving mill drive reliability.

Jan 1, 1984

By E. F. Burch, R. W. Schoenberger

This paper deals with an investigation of the use of steam filtration for filter cake dewatering and shows that it may be applied on a practical scale. The advent of larger quantities of minus 1/4 in. coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content. A lowering of the surface tension within the limits of normal wetting agent dosage results in a rather insignificant decrease in cake moisture content. Not until the dosage is increased to a point well beyond this limit is there an appreciable decrease in moisture. At these high dosage levels, interfacial tension is a major factor contributing to the appreciable moisture reduction obtained. Since no suitable method has been developed to recover and recycle this wetting agent, this phenomena is not of practical significance. On the other hand, a reduction in liquid viscosity has a pronounced effect on cake moisture. While it is readily apparent that one method of reducing liquid viscosity is to heat the entire feed slurry, it is equally apparent that this would not be an economic approach except, perhaps, in certain isolated cases. It does, however, suggest that water circuits should be designed to conserve heat as much as possible and to make use of any waste heat that may be available. The use of hot air as a heat carrying medium for drying porous materials on a filter has been practiced for many years. However, this method is restricted to materials with a high air rate in the order of 100 cfm/ ft2 because of the low heat release per unit weight of air passing through the cake. The normal fine coal filter cake has an air porosity far too low to make this a practical approach. Various types of radiant heating devices have been investigated and can significantly lower moisture content at reasonable thermal efficiency. However,

Jan 1, 1964

By B. W. Frazer

In the numbers of the Engineering and Mining Journal of June 27th and July llth, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced 60 the same standad of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of t,he pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part. of the furnace, by the dissociation of carbonic oxide, is again converted into carbonic oxide or

By A. Patton, F. N. Speller

The use of roll scale in the Bessemer process dates back, to the best of our knowledge, at least 20 years. It was first used by the Ohio Steel Go., Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam McDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to shorten the length of the blow, or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it was dumped into the empty iron ladle by the wheelbarrow-load, and at times was dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerabIe reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions. In using roll scale and other oxides of iron to facilitate and control the refining of pig iron in the converter, the Bessemer plant has borrowed one of the most active agencies used in the open-hearth process with, as would be expected, much the same results. The effect of such additions to the Bessemer charge may be discussed as to the influence of this practice on quality, production and cost.

Jan 1, 1917

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,' who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By W. -C. Huang

In this paper, a methodology for the reliability assessment of geogrid-reinforced unpaved roadways is presented, by taking into account the variability of the subgrade?s undrained shear strength. Analyses are performed using the Point Estimate Method and the Monte Carlo simulations technique. The undrained shear strength is represented by its correlation with the California Bearing Ratio and it is modeled as a random variable following a long-normal distribution. Analyses are performed for different types of reinforcement. The study provides a quantitative assessment of the variation of the system?s probability of failure with this parameter. Overall, the approach suggested in this study may be considered as a complementary approach on the traditional concepts of global or partial safety factors.

Jan 1, 2008

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001

By Fang-tu Wei

The purpose of developing this system is to monitor the operating status of the fully mechanized mining system in order to raise it's reliability. The completely mechanized coal mining system is a complex dynamic system, involving many sub-systems. It is the key of the mining process as well as a connected system composed of each working procedure. Any hitch in breaking, loading or transporting will interrupt the mining process. The analyses of the operating data has proved that the reasons causing the interruption of the extracting processes mainly come from the inner of coal face. Hence, after the installation of the MINOS system in England, the delays of belt conveyor sub-system were reduced. But the production increment was not as much as expected.

Jan 1, 1986

Coal exploration and mine planning now use all the modem techniques to indicate geological hazards to a new or developing coal mine. Drilling, seismic and other sophisticated geophysical methods aim to increase the reliability of prediction of features which will inhibit mine development. But do they?. During the past 40 years, geological investigations for coal mines in New South Wales have ranged from the general observations of Eric Rudd, in the Southern Coalfield in the late 1940s to the very detailed examinations of roof strata by John Shepherd and others in the 1980s. Then, the large scale regional relationships between sedimentary and structural features often were ignored as the minute examination of seam roof strata became fashionable.

Jan 1, 1991

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By W. W. Weller

Heat capacity measurements of anhydrous cobalt sulfate (CoSO4), copper sulfate (CuSO4), nickel sulfate (NiSO4), and zinc sulfate (ZnSO4) were conducted over the temperature range 51° to 298° K. The results were used to evaluate the following entropies at 298.15° K (cal/deg mole): CoSO4, 28.1; CuSO4, 26.8; NiSO4, 24.8; and ZnSO4, 26.4. Entropies were combined with heats of formation to give free energies of formation.

Jan 1, 1965

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997