Search Documents

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By E. G. King

An earlier Bureau of Mines report4 provided low-temperature heat-capacity and entropy data for three sodium vanadates. This report continues the study of vanadates by presenting analogous data for three crystalline calcium vanadates - calcium metavanadate (CaV206), calcium pyrovanadate (Ca2V2O7), and calcium orthovanadate (Ca3V208). No similar data for these compounds have been published previously. MATERIALS All three vanadate samples were prepared by the Bureau of Mines by heating stoichiometric mixtures of reagent-grade calcium carbonate and vanadium pentoxide.5 Calcium metavanadate was prepared at 610° to 660° C. A stoichiometric mixture was heated for 17 days with intervening grindings, mixings, and adjustments of composition, as shown necessary by chemical analysis. The final analysis gave calcium oxide, 23.48 pct. (theoretical, 23.57 pct.) and vanadium pentoxide, 76.32 pct. (theoretical, 76.43 pct.). The sample also contained 0.11 pct. acid-insoluble matter. The X-ray diffracton pattern showed no lines of free calcium or vanadium oxides. No X-ray diffraction patterns were found in the literature for any of these substances.

Jan 1, 1961

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

This presentation addresses the sources and weighting of project risk in coarse gold deposits with relevance to experiences at the Ballarat mine and Castlemaine goldfield. With sample representation and reliability often a source of great error in the resource estimation of coarse gold deposits, it follows that this matter should be of greatest risk to a mining project - but is it? What are the costs and efforts required to best quantify the sampling error due to nuggetty effect? After all, the main problem in Victorian gold mining ventures in the current decade is not the amount of gold available, but defi ning which portion of it can be converted to Ore Reserves or more so profitable gold bars. The author postulates that greater risk to the project lies in the geological interpretation and matching resource spatial parameters to mining methods, than the degree of uncertainty related to grade due to nuggetty gold. Recent experience in the Victorian goldfi elds is that the investor market has already severely discounted Mineral Resources reported in accordance with The JORC Code - so if they don't believe in the capacity to upgrade the resource why should we? To this end, Castlemaine Goldfi elds Ltd at its Ballarat gold project does not intend to estimate its gold mineralisation for public release, instead choosing to focus on the geological interpretation and mine planning elements. So with coarse gold deposits, is your Mineral Resource reported with The JORC Code a glass half full or half empty? Our mining forefathers in Victoria had no predictive tools which could define resources to any degree and yet were successful. By over emphasis on the definition of mineral resources and particularly the sampling error, are we ignoring the basics of cost control, solid geological interpretations and maximum mining flexibility. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By J. J. Scott

Friction Rock Stabilizers, trade name Split Set*, is a new support system invented by the author and under development by Ingersoll-Rand and Lee-Norse Company. Split Sets are a substitute for standard bolts or fully grouted resin bolts and have certain advantages which are: 1. Improved safety for the miner 2. A rational design is possible based on rock mechanics principles 3. Supports can be made either to be yieldable or rigid 4. Supports can be used to build a roof beam or to suspend roof material 5. It is cheaper than the resin system and costs about the same as standard bolts.

Jan 1, 1974

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By E. S. Mardock, Robert E. Bush

The object of this paper is to report recent developments in the quantitative interpretation of radioactivity logs. The use of reference lines is described in the application of the new zero radioactivity reference line for the determination of neutron derived porosities is discussed. Illustrated examples are shown of logs from the reef limestone of the North Snyder Field and from the Lansing-Kansas City limestone of central Kansas. A method of using an interrelation factor calculated from the neutron and gamma ray curves, called the neutron Productivity number, for the estimation of productivity from sandstone formations is discussed. When used in a relative manner the neutron productivity number has aided in Predicting whether a given zone will produce gas or liquid or whether it is too shaly to produce. Examples of logs from wells in the Freites District, Venezuela, and in East Texas are shown to illustrate the application of the neutron productivitv number. INTRODUCTION The petroleum industry was introduced to some of the preliminary results of investigations into the quantitative interpretation of radioactivity logs in October, 1949." It was stated at that time that the methods presented were entirely relative because they involved the use of reference points obtained from the radioactivity log, i.e., shale reference lines, dense zone reference lines, or a combination of both shale and dense zone reference lines. These relative methods offered many advantages to the industry in interpreting radioactivity logs in terms of porosity with particular application to limestone and dolomite reservoirs. However, these relative methods did not offer the wide range of applicability desired because the esta1)lishment of reliable reference points from shale in some areas were difficult. It was recognized that a more reliable mean; of establishing reference lines was vitally needed. Such a method is now available through the introduction of an instrumeutal zero device. It is the purpose of this paper to discuss the application of this new zero reference to the quantitative interpretation of radioactivity logs. Previously all applications of quantitative interpretations of radioactivity logs have been made in limestone reservoirs with little or no emphasis placed on sandstone reservoirs. A brief resumé of investigations into the quantitative interpretation of radioactivity logs in sandstone reservoirs is presented here. This discussion deals primarily with the interrelation of the gamma ray and neutron curves and the response of the latter to the density of the fluids filling the pore space in relatively homogeneous sandstones of uniform porosity. The authors believe that the methods presented herein are only applicable locally to specific fields and reservoirs, and that they probably do not offer a wide range of applicability. However, tile authors believe that the wider use of the new instrumental zero references in sand areas will reveal more information about the specific response of the gamma ray and neutron curves to changes in lithology and saturation. Two applications of quantitative interpretation using the new instrumental zero references are presented. Examples are given which show the comparison of logs and porosity in the limestones and dolomites of West Texas and Kansas. Logs of wells in 'Venezuela and East Texas are compared with the drill stem test data, production data, etc.. to illurtrate the interrelation of the gamma ray and neutron curve: and the rise of methods involving these interrelations to determine certain saturation variables. THE QUANTITATIVE APPLICATION OF RADIOACTIVITY LOGS TO LIMESTONE AND DOLOMITE RESERVOIRS Tile theoretical basis for the gamma ray and neutron curves has been discussed elsewhere.9 he method of recording the logs and apparatus involved has also been thoroughly covered and will not be discussed here.'."".'" It has been shown that the neutron curve responds exponentially to liquid filled porosity over the 1 1/2 to 35 per cent

Jan 1, 1951

By Robert E. Bush, E. S. Mardock

The object of this paper is to report recent developments in the quantitative interpretation of radioactivity logs. The use of reference lines is described in the application of the new zero radioactivity reference line for the determination of neutron derived porosities is discussed. Illustrated examples are shown of logs from the reef limestone of the North Snyder Field and from the Lansing-Kansas City limestone of central Kansas. A method of using an interrelation factor calculated from the neutron and gamma ray curves, called the neutron Productivity number, for the estimation of productivity from sandstone formations is discussed. When used in a relative manner the neutron productivity number has aided in Predicting whether a given zone will produce gas or liquid or whether it is too shaly to produce. Examples of logs from wells in the Freites District, Venezuela, and in East Texas are shown to illustrate the application of the neutron productivitv number. INTRODUCTION The petroleum industry was introduced to some of the preliminary results of investigations into the quantitative interpretation of radioactivity logs in October, 1949." It was stated at that time that the methods presented were entirely relative because they involved the use of reference points obtained from the radioactivity log, i.e., shale reference lines, dense zone reference lines, or a combination of both shale and dense zone reference lines. These relative methods offered many advantages to the industry in interpreting radioactivity logs in terms of porosity with particular application to limestone and dolomite reservoirs. However, these relative methods did not offer the wide range of applicability desired because the esta1)lishment of reliable reference points from shale in some areas were difficult. It was recognized that a more reliable mean; of establishing reference lines was vitally needed. Such a method is now available through the introduction of an instrumeutal zero device. It is the purpose of this paper to discuss the application of this new zero reference to the quantitative interpretation of radioactivity logs. Previously all applications of quantitative interpretations of radioactivity logs have been made in limestone reservoirs with little or no emphasis placed on sandstone reservoirs. A brief resumé of investigations into the quantitative interpretation of radioactivity logs in sandstone reservoirs is presented here. This discussion deals primarily with the interrelation of the gamma ray and neutron curves and the response of the latter to the density of the fluids filling the pore space in relatively homogeneous sandstones of uniform porosity. The authors believe that the methods presented herein are only applicable locally to specific fields and reservoirs, and that they probably do not offer a wide range of applicability. However, tile authors believe that the wider use of the new instrumental zero references in sand areas will reveal more information about the specific response of the gamma ray and neutron curves to changes in lithology and saturation. Two applications of quantitative interpretation using the new instrumental zero references are presented. Examples are given which show the comparison of logs and porosity in the limestones and dolomites of West Texas and Kansas. Logs of wells in 'Venezuela and East Texas are compared with the drill stem test data, production data, etc.. to illurtrate the interrelation of the gamma ray and neutron curve: and the rise of methods involving these interrelations to determine certain saturation variables. THE QUANTITATIVE APPLICATION OF RADIOACTIVITY LOGS TO LIMESTONE AND DOLOMITE RESERVOIRS Tile theoretical basis for the gamma ray and neutron curves has been discussed elsewhere.9 he method of recording the logs and apparatus involved has also been thoroughly covered and will not be discussed here.'."".'" It has been shown that the neutron curve responds exponentially to liquid filled porosity over the 1 1/2 to 35 per cent

Jan 1, 1951

By W. M. Rutherford

A knowledge of the limits of miscibility between reservoir oil and possible injection fluids is required for selection of the optimum miscible-injection fluid. Limits of miscibility can be estimated from the results of equilibrium phase-behavior experiments. They can also be determined by means of displacement experiments conducted in a high-pressure sandpack. This paper describes the equipment and procedure which have been developed for determining miscibility conditions by stable displacement. A systematic series of displacements of a West Texas reservoir oil was carried out. The results indicate that, at constant pressure, miscibility is a function only of the pseudocritical temperature of the injection gas. This fact, together with improved experimental methods, makes the displacement technique a rapid, reliable means for determining miscibility conditions. In conjunction with the displacement experiments, phase diagrams were constructed for the oil with dry gas and propane and with dry gas and ethane. Phase behavior of the methane-ethane-propane system was determined at 110°F. The experimental work demonstrates the feasibility of using ethane-rich gases to reduce cost and pressure requirements for miscible displacement. INTRODUCTION In recent years, interest in the miscible displacement of oil by light hydrocarbon mixtures has been high. Many pilot and a few field scale projects have been started.1 These projects have made use of various methods for achieving miscibility: (1) the LPG-slug process, (2) the enriched-gas-drive process and (3) the high-pressure gas-drive process. Some field projects have been successful; the results of others are debatable. In general, projects which have performed best have involved the injection of an appreciable fraction of a pore volume of miscible material. Economical application of miscible displacement depends strongly on the cost of the miscible-injection fluid. If an appreciable fraction of a pore volume of material is required for successful application of these methods, a precise knowledge of the minimum requirements for miscibility in terms of composition of injection fluid is essential. Therefore, reliable experimental methods for determining miscibility conditions are important, and a procedure for estimating these conditions from the composition of the reservoir fluid is highly desirable. The subject of this paper is the problem of determining conditions which result in miscible displacement of oil by light hydrocarbon mixtures. Miscibility conditions can be estimated by means of equilibrium experiments conducted in a PVT cell, or they can be determined by means of high-pressure displacement experiments. This paper describes the equipment and procedure which have been developed for the determination of miscibility by high-pressure displacement experiments. These methods have been applied to the displacement of a West Texas reservoir oil with mixtures of dry gas, ethane and propane. In conjunction with the displacement experiments, triangular phase diagrams have been constructed for mixtures of the oil with dry gas and propane and with dry gas and ethane. The effect of injection-gas composition on conditions for miscible displacement in high-pressure sandpacks and cores has been the subject of several published papers.2-5 The experimental methods used in these investigations were such that displacements were unstable, and the effects of fingering and/or gravity layover are clearly evident in the results. Miscibility conditions were probably correct in spite of the instability phenomena, but the experiments evidently were time-consuming, and limited data were reported. Systematic high-pressure flow studies which would support a correlation of miscibility conditions have not been reported; however, Wilson5 has proposed the use of pseudocritical temperature of the injection gas as a parameter and Benham, et al,6 have based a miscibility correlation on observed and calculated equilibrium data.

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By William F. List, Marvin A. Schuster

Monolithic electrooptical mosaics of 2500 photo-transistor elements with internal row and surface column interconnections have been fabricated by epitaxial-planar diffsion techniques. Unique access to any elemed of the mosaic is provided through one of the fifty X and one of the fifty Y external leads. The sensor mosaic can be used for imaging applications and has a 1:1 aspect ratio, a resolution of 100 lines per in., a dynamic range in excess of lo3, a sensitivity of 0.5 per pw, element response within a 2:l range over 75 pct of the mosaic, and a minimum detectable signal of the order of 10-' w. Design considerations which ilnpose particclar fabrication yequirements are disctussed along with some of the problems peculiar to the epitaxial and planar-dijfision techniqes by which this device is fabricated. The solid-state silicon monolith has an imaging area of 0.5 by 0.5 in. and an element center -to- center spacing of 0.010 in. J monolithic solid-state electrooptical device has been developed as the photon-sensing mosaic for use in an image-converter system.' This system is the solid-state equivalent of the vidicon and can image radiation in the visible and near-infrared regions of the spectrum. The electrooptical image converter has the desirable size, weight, reliability, and low-power characteristics inherent in solid-state devices. It is read out by direct-wire means rather than by beam-scan techniques. The packaged unit is shown in Fig. 1. A selection of material for the sensor was based on considerations of both reliable fabrication techniques and material spectral response. Silicon was selected both for its response from the lower end of :he visible to the long-wavelength cut-off above 11,000A and for its well-developed epitaxial planar-diffused technology. The electrical image is composed of M x N discrete information bits with each bit emanating from one of the individual phototransistor sensors. The interconnected mosaic concept was introduced to provide a structure which is both manageable in its number of leads and compatible with conventional viewing systems which accept XY data. Interconnections along the Y direction are provided by internally diffused strips, while interconnections along the X direction are formed by vacuum-deposited metal surface bars. Unique access to any individual element of the M x N mosaic is available through one of the M and one of the N external leads. PHOTOTRANSISTOR DESIGN A phototransistor structure2 was selected for the discrete photon detectors of which the mosaic is com- posed. Basically, the mode of phototransistor operation is such that incident quanta are absorbed in the base area of the element where they generate electron-hole pairs. If the electrons are liberated within a diffusion length of the depletion region around the collector junction, they will diffuse to this depletion region and be swept across the junction where they account for a small component of the photocurrent. Similarly, the holes which are created within a diffusion length of the emitter junction will diffuse to this region where they forward bias the emitter and so induce injection of minority carriers into the base. This accounts for the substantial transistor photocurrent. This mechanism of operation implies several design and fabrication goals for the individual sensor elements: high electrooptical conversion efficiency, sufficient carrier lifetime in the base regions, and a maximum volume in which photons can be absorbed within a diffusion length from the depletion layer about the junction. Moderately high transistor gain is desirable to permit readout at low light levels; however, very high gain has a deleterious effect on mosaic dynamic range. The mosaic must also be characterized by good uniformity of element response as well as by good isolation between elements. The above set of conditions imply that junction depths must be optimized with respect to photon ab-

Jan 1, 1967

By C. L. Pillar

INTRODUCTION The location, size, character of the ore de- posit and its adjacent formations will deter- mine the mining system best used for its ex- traction. The mining system chosen will have to be engineered to suit the ore deposit and the people that will extract it. What can be done in the Philippines cannot always be accomplished in the upper Northwest Territory of Canada. Mining operations developed under a free enterprise system are planned to achieve a satisfactory return on the capital required to place them into production. Hence, the choices made in planning and developing the mining system must be dictated by sound economics. The mining system planned must favor: 1. Maximum ore extraction of the deposit with minimal grade dilution. 2. The amount of capital expenditure used to develop and equip the mine must be in harmony with the financial policy of the group yet be sufficient to provide a reliable mining system. Excessive frills and extras that are not required for efficient, safe production should not be provided. 3. Mine production costs are determined by the amount of men, material, equipment and energy used in the production process. These must be kept to minimal limits in order to insure dependable, low cost production. Extras that later are needed in the production operation can be added as required by the operator. Basically block caving is a mining system that is normally used to extract deep seated, massive, low grade deposits of copper, molybdenum and iron where stripping ratios for open cast mining are economically prohibited. The caving system is limited in its selectivity. It is a mass production type of underground ore extraction that under favorable conditions is one of the most efficient, low cost mining systems in the world today. Usually block cave mining systems are large. They are capable of producing ore at a rate of 10,000 to 100,000 tons/day from large deposits at costs that are comparable with many open cast mining systems burdened by high waste to ore ratios. Block cave mining systems differ basically in the plan of the area layout, the method of undercutting and the method of draw. The balance of the mining system is the mechanical transportation of the drawn ore to the surface, the mine supply, drainage and ventilation systems. This paper deals mainly with the methods of draw. The method of draw to be used in a block caving system dictates the development plan of the mining area, is highly influential in the method of undercutting to be employed and the supply and ventilation system to be used. There are three basic methods of draw commonly used in today's operations. They are: Gravity draw Slusher draw LHD draw The type of draw planned will have a major affect on: Capital expenditure and time required to bring a deposit into production. Productivity, efficiency and cost of the production operation. Percent recovery of the ore deposit in both tonnage and grade. Degree of production reliability Fundamentally the type-of draw used must be compatible with the physical characteristics of the deposit to be extracted and the financial position of the mining operation. The type of draw chosen must work to advantage with the size, configuration, depth, strength and fracture pattern of the deposit and its adjacent formations. It must favor the financial protection of the planned mining operation. A Gravity Method of Draw requires a finely fragmented, easy flowing product from the caving action of the deposit. To obtain the desired economic advantage the ore deposit must also have sufficient area and height of column to permit minimal development cost on a per ton basis. The gravity system re- quires the maximum amount of development openings and uses the minimum amount of mechanized equipment of all the caving systems. It is unskilled, labor-intensive and is highly sensitive to size of ore fragmen-

Jan 1, 1981

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically, the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived 'resource converted to reserve' area (which is based on the business plan from CADSMine?) versus the 'resource available for mining' (which is derived from Datamine?) underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2013

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By L. S. Kolbert, C. H. Baab

Introduction In June 1981, the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the US coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent." With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. Major Features and Benefits of Nuclear Measurement and Analysis Systems There are many features and benefits of nuclear instrumentation. The major benefit is that nuclear instrumentation is non-contacting. The measuring heads do not contact the process materials. This enables measurements of corrosive, abrasive, or high temperature materials with no loss of performance, reliability, or useful life. Also, there are no moving parts to wear or be fouled by dust or corrosion. Installation is simple and inexpensive. For instance, density gauges are simply clamped onto existing pipe runs. Weigh scales and level switches usually require nothing more than welding brackets to customers' equipment. Once installed, routine maintenance can be performed without interrupting the process. Thus, nuclear instrumentation is highly reliable and easily installed and maintained. The operating life of the instrumentation is virtually unlimited. Principle of Operation Nuclear belt weigh scales, point level switches and density gauges all operate on the gamma-ray transmission principle. A beam of gamma radiation from a radioisotopic source is projected through the process material either on a belt, in a vessel, or in a pipe. Opposite the source is a radiation detector whose electrical output is proportional to the intensity of the radiation it absorbs. Gamma radiation is part of the same electromagnetic spectrum that encompasses light, infrared, and x-rays. In many respects, gamma radiation behaves much like light. However, it is far more penetrating and can be transmitted through considerable thickness of materials that are opaque to visible light, e.g., several inches of steel. Types of Nuclear Instrumentation in Coal Preparation Plants There are four types of nuclear instrumentation presently being employed in coal preparation plants. They are: •Belt Weigh Scales •Point Level Switches •Density Gauges •Coal Analysis Equipment. Each type of instrumentation has a number of potential applications within the plant. What follows is a discussion of three different types of devices and their applications. Weigh Scales In coal preparation plants, weighing instruments are used for measuring material throughput, totalized weight, and batch weight on conveyor belts and other transport equipment. They are also used on drag chain conveyors, vibrating conveyors, and screw conveyors. Weighing is important for receiving the run-of-mine coal, controlling mass flow, scheduling production, and loading and shipping the washed coal to market. There are two basic types of weighing instruments: gravimetric and nongravimetric devices. Gravimetric devices are units which measure the pull of gravity on the material being weighed. Nongravimetric devices are not dependent on the force of gravity on the sample. Nuclear weigh scales are the most prevalent nongravimetric devices used. The nuclear weigh scale works on the same basic principle as other nuclear gauges. The greater the quantity of material placed in the path of a radiation beam, the more radiation will be absorbed by the material. In weigh scales, Cesium 137 source is generally placed above the moving stream of material so that the radiation is directed through the material. An ion chamber radiation detector is on the opposite side of the material. The radiation passing to the detector generates a signal which is inversely proportional to the weight of the material present. This signal is amplified and integrated with the speed of the process flow yielding the weight. The weight is indicated and can be totalized for throughput, batch control, etc. In conclusion, radiation weighing methods have become well established in the coal preparation industry throughout the world. As mentioned before, this device finds its most

Jan 1, 1985

By G. B. Thomas

Several methods of analyzing pressure build-up data in wells have been presented by various authors. This paper reviews the theory and method of D. R. Horner and presents example calculations performed on data obtained by testing several different types of wells. These calculations include, (1) graphical estimation of final static pressure, (2) determination of the productive capacity of the pay away from the well bore and. (3) the degree to which the formation adjacent to the well bore has been damaged by completion or other causes. The methods of testing and precautions which should be taken to assure the best data possible are discussed. Limitations and reliability of calculated results are also treated. INTRODUCTION Pressure testing of wells is generally limited to the determination of producing and static mean formation pressures. The so-called "static" pressure determination.. along with PVT, electric log and production data, enable the reservoir engineer to determine, within reasonable limits, the drive mechanism of the reservoir and in some cases. the amount of edge water encroachment. Producing pressure tests enable calculation of productivity indices and allow the engineer to plan the systematic production of a pool for optimum conservation of suhsurface energy. The radial flow formula advanced by Muskat' has been based on the assumption of incompressible radial fluid flow. It has been known that reservoir fluids do not behave in an ideally incompressible manner. For example, incompressible flow theory indicates a simple logarithmic relationship between the difference of the instantaneous and static well pressures when plotted against time. 'The latter stages of this type of plot of pressure build-up data generally show a marked devia-, tion from the earlier straight line trend. which deviation may be shown to be due to the compressible flow of fluids toward the well bore. Shut-in times of 24, 48. 72. or at most 96 hours are currently in wide use for determining so-called "static" reservoir pressure. Due to the continuation of compressible flow of fluids into the well bore long after this arbitrarily taken shut-in time, the determination of static pressures has almost invariably resulted in lower than equilibrium values. Materials balance calculations made early in the life of a reservoir often result in a calculated reserve which later observations prove to be too low. Failure to obtain reliable "static" reservoir pressures within the prescribed 24 or 48-hour build-up period has undoubtedly been a major factor in obtaining these low estimates. Comparison of theoretical and actual productivity performance has indicated that formation damage and not being able to attain true static pressures have been partially responsible for the observed discrepancies. Research into the theory of compressible flow behavior has resulted in methods of applying these theories to the testing of wells. Application of the developed theories to pressure build-up performance indicates that in many cases the following can be estimated. 1. The static reservoir pressure. 2. The in-place effective formation permeability away from the well bore. 3. The degree or extent by which the formation has been damaged adjacent to the well bore, either through completion methods or subsequent damage due to fluid entry. REVIEW OF THEORY Horner2 has shown that the pressure build-up within a "point source" well is approximated by the following formula: Equation (1) is the approximate "point source" solution to the radial compressible flow equation advanced by Muskat. The solution assumes the following: 1. A point source well is producing at constant rate from the center of an infinite reservoir with a constant pressure at its external boundary. 2. The fluid flowing is present in one phase only. 3. The compressibility and absolute viscosity of the fluid remain essentially constant over the range of temperature and pressure variation encountered. 4. The well i.; shut-in at the sand face arid there is 110 after production into the well bore. 5. The formation permeability is homogeneous in the direction of flow. From Equation (1) it can be seen that if an ideal well were shut-in while producing from a reservoir under the conditions assumed, the pressure build-up would be a logarithmic func-

Jan 1, 1953

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962