Search Documents

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate as mines are being developed. In this study, finite element method has been used with optimization criteria to design more stable and safe underground openings.

Jan 1, 1993

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By Jae-Hyung Park

Since the Industrial Revolution, the land resources have been decreased rapidly as the industrialization. And this phenomenon brings to our mind an interest in deep-sea resource(manganese nodule). Hence, Korea has been participated in the development project of exploiting manganese nodule since 1983. Hwang and cho(1998) studied the economic efficiency evaluation of manganese nodule carrier. But they used the TAMU(Texas A&M University) model, and assumed deadweight and velocity of bulk-carrier. If we use some optimization technique, more economic manganese nodule carrier can be selected and evaluated without limited assumption. In this study, we evaluated the economic efficiency of manganese nodule carrier using genetic algorithms(GAs).

Jan 1, 2003

By T. B. Linde

The Morenci In-pit Crusher and Conveyor System has been designed with safe production and cost savings in mind. Large open pit mines around the world have been installing semi-mobile crushers and linking them with a pit conveyor system to lower unit cost. At Morenci two 60/89 in. gyratory crushers are incorporated into the semi-mobile crushing plants. The ore is reduced to -8 in. and transported out of the mine on a 60 in. steel cable belt. This paper includes an overview of the Morenci In-pit Crusher and Conveyor System from the drawing board to open pit installation and finally a discussion on operating and repair considerations.

Jan 1, 1990

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

By Charles L. Kimbell

In 1988, the aggregate value of total world international export trade in mineral commodities was estimated at nearly $542 billion in current (1988) dollars, which was about 8.6% above the 1987 level, but still 23.7% below the record high set in 1980. Comparable comprehensive data for 1989 were not available in time for inclusion in this chapter, but 1989 returns for developed market economy countries only were 1 1.8% above those for 1988. These countries accounted for about 50% of the total mineral commodity export trade in 1988. It would be unsound to utilize the overall 11.8% growth rate for mineral commodity export trade for these countries to extrapolate the growth in total world mineral commodity trade because these developed market economy countries account for substantially different shares of the five major mineral commodity groups listed in table 2. Specifically, developed market economy countries in 1988 accounted for 56% of world export of ore, concentrate, and scrap, 74.7% of world exports of iron and steel, 71.7% of world exports of nonferrous metals, and 57.8% of all exports of crude nonmetals, but only 26.6% of world exports of mineral fuels. Moreover, even within each of these groups, the actual product mix included in developed market economy country aggregates differ from that in developing market economy country aggregates and in centrally planned economy country aggregates. Nonetheless, an increase of 9% to 12% in the value of world mineral commodity export trade seems indicated by available returns.

Jan 1, 1992

By Cláudio Antunes de Oliveira

Este trabalho tem como objetivo demonstrar uma aplicação prática da técnica de reconciliação de dados no diagnóstico das medições que compõe uma malha de distribuição de gás BFG – Blast Furnace Gas. Falhas comuns de medição tais como saturação e congelamento da indicação afetam a qualidade da informação e este tipo de detecção faz parte da proposta de diagnóstico. Será abordado o desenvolvimento de um algoritmo que implementa a técnica de reconciliação, bem como a elaboração de uma matriz de diagnóstico no InfoPlus.21. Os principais indicadores deste diagnóstico são armazenados na base de dados do InfoPlus.21 visando consultas históricas e monitoramento contínuo das medições. Os dados obtidos demonstraram que a técnica de reconciliação de dados pode contribuir para identificação de falhas e agregar confiabilidade às medições.

Jul 30, 2018

By Caroline Gomes de Oliveira

As fibras lignocelulósicas representam vantagens econômicas, técnicas e ambientais em comparação com as fibras sintéticas, como fibra de vidro por exemplo, quando se considera as alternativas de reforço aos compósitos. A fibra natural usada no presente trabalho é a fibra de eucalipto, que é largamente cultivada em território brasileiro. Este trabalho tem como objetivo avaliar uma análise estatística da correlação entre o diâmetro e a densidade da fibra de eucalipto. Para isso, foi aplicado o método de Weibull. O diâmetro foi obtido por meio de medições em projetor de perfil, enquanto a densidade utilizou determinações precisas da massa e do volume de fibras. Os resultados revelaram uma dependência inversa entre o diâmetro da fibra de eucalipto e sua densidade

Aug 17, 2017

By Glenn J. Phillips, Debra L. Musick

The operating mine is dynamic, everchanging, and a continuous moving target. The only way to effectively manage such a creature is to be able to evaluate the cost of operation over short enough time periods that rapid effective controls can be implemented before loss can erode the marginal profits in todays market place. Such short term evaluations can provide the basis for the long range planning that can keep an operation healthy in the future. The spreadsheet programs on small computers (PC's) offer the possibility of such evaluation by accumulating data in a useable format, providing timely cost reporting and providing a tool for use in evaluating the day to day alternative choices of the real mining world.

Jan 1, 1987

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

For small particles of niekel flotation eoncentrate (av. size 50 pm) the predominant heat transfer mechanism under suspension smelting conditions, prior to ignition, is conduction from the gas and not radiation from nearby hot bodies. Results of laboratory tests using gas temperatures 380-700°C and furnace wall temperatures 380-1100°C were in accord with heat transfer theory. In practieal flash smelters earlier ignition, and hence better utilization of the space in the shaft, would result from introduetion at the top of the shaft of gases hotter than the ignition temperature of 500-600°C.

Jan 1, 1979

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By Gordon Smith

ABSTRACT Gold-bearing quartz veins in the northeastern Ontario and north western Quebec mining camps are shown to have been mineralized in part by epithermal solutions. The vertical gradient of pressure during this stage of mineralization is calculated, using decrepitation temperatures of quartz and thermoelectric potentials of pyrite. The base of the Cobalt sediments, which lie uncomformably over part of the mining region, may be taken as datum level in calculating the depth of erosion into the basement below that level. The vertical extent of the epithermal gold mineralizaiton in this region is at least 9,000 feet below the datum level. INTRODUCTION IT WOULD have been difficult a few years ago to convince economic geologists that after making a series of measurements in a laboratory in Toronto, the depth of erosion which has taken place below the base of the Cobalt sediments at any place in the Ontario-Quebec mining region can be calculated to the neare.st 500 feet, or that the same series of measurements would also serve to allow a prediction of the minimum vertical depth of probable ore in a producing mine in the same region, with the same degree of certainty. Possibly it is just as difficult today, but the following description of the data and calculations may help to demonstrate the reliability of the method.

Jan 1, 1951

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By L. W. Strock

Metallurgists handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. 'lore preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The howledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Expcrience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,' but the incentive has gradually changed since the summer 0. 1940 to the specific practical problem of searching for domestic sources of rare and stratcgic metals. The

Jan 1, 1949

By Lester W. Strock

METALLURGISTS handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. More preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The knowledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Experience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,1 but the incentive has gradually changed since the summer of 1940 to the specific practical problem of searching for domestic sources of rare and strategic metals. The

Jan 1, 1945

Federal regulations require the use of methane monitors on all mining machines. All machine-mounted methane monitors currently used in underground coal mines rely on catalytic heat of combustion sensors. As a comparison, although not currently approved for use on underground mining equipment, instruments with infrared sensors are evaluated in this study. Potential advantages of using infrared sensors include faster response time, long-term stability, and reduced maintenance needs. Tests conducted in the laboratory and at a full-scale model mine compare the performance of catalytic heat of combustion and infrared sensors operating under test conditions designed to simulate airflow conditions underground.

Jan 1, 2009

By A. Ennen, R. Wagner, B. Orberger, J. -M. Milazzo, N. Uhlmann, J. Banchet, J. Lucic, N. Wörlein, M. Firsching, J. L. Dubos, C. Bauer

The residues from mining and processing ores can often be considered as secondary raw materials. However, the material is only available in the form of fine particles (< 3 mm). In order to recycle these wastes, it is necessary to agglomerate it for transportation prior to reprocessing. The resulting agglomerates need to mechanically resist the stress of transportation and loading into the furnace. X-ray computed tomography (CT) is an established method for characterisation of internal structures in material science. This non-destructive technique can provide information on size and distribution of particles and grains. However, the information is not limited to the size, but also can yield structural features like orientation and position of cracks and fractures, which are important features indicating potential for deteriorating the agglomerates. Furthermore, deduced features such as contact conditions of inclusions or boundary surfaces can also be calculated. We studied binder-free tablets of manganese-oxyhydroxide, bentonite, kaolinite and slag powder using micro-CT. Inclusions of highly absorbing particles were identified using a watershed transformation with automatic segmentation by Otsu thresholding. Subsequently, the resulting data was analysed regarding their volume percentage, distribution in size and location within the sample. For the slag agglomerates, the volume fraction of iron could be determined. Furthermore, visible cracks were investigated with the goal to determine the long-term durability. It was shown that the data provided by micro-CT is reliable and helpful for the characterisation of industrial waste agglomerates. Keywords: X-ray, computed tomography, micro-CT, agglomerates, manganese fines, slags, kaolinite, bentonite

Jan 1, 2020