Search Documents

By lves Matiolo, Jorge Rubio, Carlos Perez Guerrero, Denise G. Nunes, Fabiano Capponi

The problem (very old) of processing by flotation, the fine (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral particles continues to be a major technical challenge in the area of mineral processing. Many different processes have been proposed over the last three decades but, unfortunately, most of them have not found practical applications yet. This paper describes some advances in flotation research in fines (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral recovery by two different techniques. Extender flotation (EF) and flotation with bubbles with a wide size distribution-SB of copper sulphide ore fines (1 % Cu) were compared with a “standardised” (STD) mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), “true” flotation recoveries and process kinetics. Copper porphyry samples, containing about 1/3 of the mass and about 37 % of the total copper content in the fines and ultrafines fractions were used. In the EF tests diesel-in-water emulsions were used as an extra reagent, added after the collector and frother addition. In SB tests, drawing air through an aspiration nozzle, directly in the pulp, generated bubbles sized about 50-200 µm. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physicochemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged. The following figure shows size-by-size copper recoveries results, after classification of produced concentrates and tailings using micro-sieves. Results clearly show that flotation of the F and UF fractions is highly improved with injection of small bubbles (SB) and with the addition of an extender collector. It is believed that the techniques presented here will establish shortly a new basis for the flotation enhancement of the F and UF, aimed at solving a very old problem. This work is being continued, now at pilot plant scale, and results will be published en the near future.

Jan 1, 2003

H. RIES, Ithaca, N. Y.-The part of Mr. Fiske&apos;s paper that interests me especially is that portion dealing with the raw materials, and the tests that were applied to the raw materials in order to determine their value in advance, if possible, because that, I believe, is a step in the right direction. For a number of years I have done my best to persuade different consumers of clay to develop standard methods for testing raw materials. We have in this country a large variety of clays which can be used for a great many different purposes, but in many cases the consumers either have no standard methods for determining the value of those clays in. advance, or if they have they do not publish them; consequently it often puts the clay miner at a disadvantage. If, for example, manufacturers of different types of refractory materials would state publicly just what physical tests their raw materials have to meet, it would, I believe, help them to find more easily the materials that they are looking for, and the clay producer would also be benefited. It would also encourage him to have his clays tested in advance, so that samples could be accompanied by certificates of physical tests that would be of convenience to the manufacturer. At the present time, in this country there are certain types of clay which seem to be rather scarce. There apparently are not many deposits of clay that are exactly suited for the manufacture of zinc refractories. So, too, there are not many deposits of clay that are suited for the manufacture of glass-pots, or the blocks for glass tank furnaces, or clays that can be used for graphite crucibles. Now, in many cases, no standard series of tests has been developed. I am also gratified to see that Mr. Fiske considers the tensile strength. tests of value. Some years ago the American Ceramic Society appointed a committee to draw up a series of recommendations covering standard tests. These recommendations were especially for the use of State geologists and the U., .S. Geological, Survey. Among the tests that were considered was the tensile-strength test, which Mr. Fiske has mentioned in his paper. Unfortunately, a majority of the committee turned it down, and the test was therefore not officially approved, but two of us, who formed the minority, believed in it. Since then the other members of the Committee have come to see that that is an important test to make and Mr. Fiske has emphasized it in his paper.

Jan 1, 1918

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019

F. AT. FARMER*, New York (written discussion?)- The paper presents many phases of the welding art concerning which there are very divergent views. In many cases, the wide differences of opinion are based on the results of mechanical tests, but an examination of the mechanical test data discloses a wide variation in character of the tests made and in the details of procedure, so that it is frequently not only difficult to analyze and check the basis of the conclusions but impossible to correlate various groups of test results. It would seem, therefore, that the technique of testing welds is one of the phases of the welding art that should be studied and standardized in order that the results of mechanical tests made by different people may be strictly comparable and have the same significance to all. The vital difference between testing a specimen of steel that includes a welded joint and testing an ordinary specimen is the non-homogeneity of the weld specimen. The weld specimen has at its center a section composed of material that usually has physical, chemical, and metallurgical characteristics distinctly different from the adjoining metal. Furthermore, the section of added metal is more or less irregular and the ratio of added metal to original metal in the section is quite variable. Consequently the details of procedure and of recording data should be more minutely prescribed than in the testing of ordinary specimens. A conspicuous example f a mechanical test that requires standardization is the cold bending test, a standard test for mild steel. With the usual method, the specimen is bent around. a pin of prescribed diameter and, as all specifications usually require bending to 180° without fracture, the manner of applying the load is immaterial because the specimen is ultimately completely wrapped around the pin. But a specimen containing a welded joint at the center will usually not withstand bending to 180° because of the much lower ductility of the deposited metal in the weld. It is therefore obvious that the farther apart the points of support are the greater will be the angle attained before cracking occurs, simply because most of the bending will take place in the original metal. It is therefore highly desirable that there be prescribed a standard test that fixes exactly the distance between the supports, the curvature of the surface of supports, and the relation between this curvature, that of the loading surface, and the thickness of the specimen.

Jan 5, 1919

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By Douglas D. Reynolds

Intense vibration can be transmitted to the hands and arms of workers who use hand-held percussive or vibrating devices, tools, and work pieces. Continued habitual exposure to vibration directed to the hands can cause patterns of various symptoms associated with hand-arm vibration syndrome (HVAS). The International Organization for Standardization (ISO) first published ISO 5349 in 1986.3 This standard specified methods for measuring and evaluating vibration directed into the hands from hand-held vibrating devices, tools, and work pieces. The American National Standards Institute (ANSI) published ANSI S3.34 the same year.1 This standard was modeled after ISO 5349-1986 and specified methods for assessing exposure to hand-arm vibration. The Parliament of the European Union has issued the European Union Human Vibration Directive-2002/44/EC, which specifies vibration daily exposure action values (DEAV) of 2.5 m/s2 and daily exposure limit values (DELV) of 5.0 m/s2. These values have generally been accepted by medical experts, scientists, and engineers in governmental agencies, research institutions, and industry in the USA and other countries.2 When they are achieved, they will reduce the potential for the development of symptoms related to HAVS among workers exposed to hand-arm vibration. Significant improvements in measurement and analysis instrumentation, miniature and subminiature accelerometers, and medical diagnostic and assessment protocols have being introduced since 1986 when ANSI S3.34 was first published. In response to these improvements and the introduction of the EU Human Vibration Directive, ANSI Working Group S2.39 developed the revision to ANSI S3.34, which has now been published as ANSI S2.70-2006.2 Method ANSI S2.70 specifies the use of the hand-arm vibration measurement procedures outlined in ISO 5349, Parts 1 and 2.2,4,5 It requires the measurement of ISO frequency-weighted acceleration values in three mutually orthogonal axes of vibration. These values are then vectorially added to obtain the vibration total value, ahv: [ ] where ahwx, ahwy, and ahwz are the measured r.m.s. ISO frequency-weighted acceleration values in the x, y, and z directions, respectively. If multiple vibration exposure events are experienced during a work day, the overall vibration total value is obtained from: [ ] where ahvi is the vibration total value of the ith operation, Ti is time duration in hours of the ith operation, n is the total number of operations, and T is total time in hours associated with the n

Jan 6, 2006

Planning for the Macraes Extension project highlighted the need for additional tailings storage availability. The possible solution of developing new tailings impoundments in Northern Gully, in tum, led to concerns being expressed by the regUlatory authority over the assimilative capacity of Deepdell Creek. Philosophical differences over the appropriateness of applying a seepage model used to set standards in consents for the original project resulted in the company re-evaluating the whole monitoring system associated with tailings disposal and seepage control. Re-evaluation indicated problems arising from the existing in-stream water quality monitoring in respect of protection of the aquatic ecological system and verifiability of results. A new monitoring system was designed relocating the compliance monitoring point out of the stream and into the gully containing the tailings impoundments giving greater certainty of monitoring results to all parties and providing improved protection for the aquatic ecology of Deepdell Creek.

Jan 1, 1993

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau&apos;s continuing Mineral Land Assessment (MLA) mining district program. The Bureau&apos;s MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By M. Bhandari, D. Norval

The bulk of plain carbon steel is produced through conventional Basic Oxygen or Electric Arc Furnace routes where the development of the AC Ladle Furnace has made it possible to also produce alloy steels. Smaller Ladle Furnaces have limitations such as lower efficiency; high electrode consumption and diminutive yields rendering them uneconomical to operate and making the processing of low carbon steel grades difficult due to carbon pick up. The demand for special steels and alloys with strict specifications is increasing while commodity prices remain competitive. The production of special steels and alloys have specific process control requirements and the development of the induction melting furnace (IMF) has made it possible to produce smaller batches economically. Refining and alloying of the melt in the IMF further enhance the efficiency. The INDUREF furnace offers increased productivity and flexibility through increased thermal efficiency and can be utilised for holding molten metal for further processing such as granulating, atomising, nitriding, alloy additions and desulphurisation of Ferro-alloys and steels. The system utilises a specially engineered ladle which is placed in an induction-heating assembly comprised of a stationary water-cooled copper coil and lamination packs. The addition of equipment for vacuum degassing and decarburisation of steels and alloys is also feasible. Benefits are: ? No electrode consumption or carbon pick-up ? Lower installation, operation and maintenance cost. ? No line-flicker facilitates operation on a weak power grid. ? Good power factor and balanced load ? No skull formation and reduced refractory consumption ? Higher yield of Fe-alloys ? Automatic controlled stirring

Jan 1, 2004

By W. A. Gericke, B. Olmstead, I. Mc Dougall, C. F. R. Smith

A finite element model was generated of a Søderberg electrode in a ferromanganese smelter. In this model, the casing and fins were modelled explicitly, and temperature-dependent material properties were included. A two-stage analysis procedure was used, the first part being a coupled thermal-electrical analysis using an applied DC current. As the casing material was non-magnetic, the DC current was deemed sufficiently accurate for this initial analysis. The proximity effect was not considered. Thermal boundary conditions based on assumed temperature distributions in the furnace were applied. Calculated temperatures agreed well with measured values. The joule heat calculated in this step was applied as a load to a coupled thermalstress analysis. The model was applied to a comparative study of alternative materials for the casing and fins. A number of different combinations of materials for the casing and fins were evaluated in a comparative study. The position of the baking zone was used as the criterion for evaluating the potential of each material combination. Based on this analysis, some material combinations were discarded as being entirely unsuitable, whilst the two most suitable combinations will be tested experimentally in the furnace. The stress analysis was performed on the most suitable option. The practical advantage of this analysis was that a number of what-if scenarios could be evaluated and discarded prior to embarking on expensive experimental work, thus limiting the amount of experimental effort required. A mathematical model allows for the comparison of options under controlled conditions, where parameters of interest can be varied individually, with all other parameters remaining the same, a condition which is difficult to achieve in an operating furnace.

Jan 1, 2004

By Nicholas J. Grant, Rolf Nordheim, Thomas B. King

Constant-load creep-rupture tests were conducted in an argon atmosphere at temperatures of 1600 to 2200°F on two heats of iron containing about 0.06 and 0.09 pct P in solid solution. The tests were conducted in the as-cast condition. Stresses were selected to give strain rates approaching those encountered in the hot working of steel, and within the limits of the creep-rupture test apparatus, namely. from about 0.001 to 50 pct per sec. FOR generations, rolling and forging practices have been developed largely by empirical methods, based on prior experience. While largely successful, difficulties are frequently encountered when new or different alloy compositions are tried for the first time. There is need to know the relationships which exist among temperature, strain rate, composition, and other variables on the deformation and fracture characteristics of steels. It has been shown for aluminum and several high-temperature alloys that the deformation and fracture characteristics follow rather well-defined laws and patterns which are closely related to the effects of strain rate, temperature, and composition.1"3 As the melting temperature of aluminum or its alloys was approached, it was possible to study the interplay of work-hardening factors and recovery or recrystal-lization, the latter resulting in improved ductility and increased resistance to intercrystalline fracture. In particular, the effects of composition are very poorly known. Within the meaning of "composition" should be included impurity elements, such as sulfur, phosphorous, lead, copper, and many others, as well as those elements which are added for alloying purposes in iron. The role of multiphase structures, in contrast to solid solutions, should also be studied in much greater detail. high strain rate creep-rupture tests would provide information regarding the deformation and fracture characteristics of metals at hot-working temperatures. It was also desired to establish the stresses which are necessary to accomplish the desired deformation, and to relate these to the strain rate and temperature. Secondly, it was the purpose of this particular study to determine the effects of phosphorus, within solid solution limits, on the deformation and fracture characteristics of iron at hot-working temperatures. EXPERIMENTAL PROCEDURE Two phosphorus levels were selected, one corresponding to the upper limit normally found for commercial steels, and one substantially higher than this, but within the region of solid solubility at the test temperatures chosen for this investigation. Twenty-pound heats were prepared by induction melting electrolytic iron in air in a magnesia lined furnace. After deoxidation with about 0.2 pct Al, ferro-phosphorus was added, and the heats were then poured into prefired silica molds. The purpose of using silica molds was to obtain a slow cooling rate during solidification to produce a relatively coarse grain size, producing a structure subject to some segregation and therefore more nearly characteristic of ingot structures. The major part of the casting assembly provided a large shrinkage head in order to produce sound castings and to promote slow cooling of the specimens. The primary austenitic grain size varied from ASTM No. 2 to No. 00. The composition of the heats, including a low phorphorus melt, used for comparison purposes, is shown in Table I. It will be noted that the oxygen content of the phosphorus containing heats is relatively high, in spite of the deoxidation practice, a condition which is difficult to control in small melts. Creep-rupture tests were nevertheless undertaken when it was noted that this quantity of oxygen did not appear to give results any different from those from a heat containing 0.01 pct 0, low phosphorus and comparable carbon Content;4 see Table 11.

Jan 1, 1961

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.&apos; , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.&apos; At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,&apos; the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955

By G. Krauss, J. M. Thompson, H. Y. Kumagai

Boron-doped p-type and arsenic-doped n-type source materials were used to deposit thin silicon films on amorphous fused quartz substrates by cathodic sputtering in argon atmospheres. All as-sputtered films were found to have high electrical resistivities of about 104 ohm-cm, despite controlled variation of the substrate temperature from 50O to 400°C. The high resistivity of the n-type films persisted even after postdeposition heat treatments as high as 1000°C, while p-type films showed a sharp decrease in re-sistivity to values on the order of 1 ohm-cm or lower after heat treatments above 650°C. X-ray and electron diffraction, together with transmission electron microscopy of the p-type films, revealed that the improved electrical properties resulted from two distinct processes. A primary crystallization or recovery within the pains, which were approximately 200Å diam in the as-sputtered films, accompanied the initial sharp drop in resistivity at 650°C. Following this process, a secondary recrystallization or discontinuous grain growth was nucleated in films heated at 1000°C. The resulting significantly increased size of certain grains and the corresponding decrease in grain boundary area accompanied an additional decrease in resistivity after heat treatment at 1000°C. The properties of thin silicon films are of interest because of their possible application in device technology. Although evaporated silicon films on amorphous substrates1-3 and both sputtered and evaporated germanium films4-&apos; have been studied in some detail, sputtered silicon films have not been widely investigated. It has been observed that evaporated silicon films deposited at substrate temperatures below approximately 600°C are amorphous.1,3,9,10 At substrate temperatures higher than this, the films are polycrys-talline, sometimes exhibiting a fiber texture with the fiber axis normal to the substrate surface.&apos; Similar results have been obtained with germanium films, although in this case the substrate temperature for the amorphous to crystalline transformation is reported to be as low as 150OC.5 The mechanism of film deposition by cathodic sputtering differs markedly from that of thermal evaporation. It might be expected, therefore, that the properties of sputtered and evaporated silicon films would also differ. The purpose of our study was to determine the effects of deposition conditions and heat treatments on the electrical resistivity, structure, and composition of thin silicon films sputtered on fused quartz substrates. EXPERIMENTAL DETAILS Apparatus. A schematic diagram of the sputtering apparatus is shown in Fig. 1. The vacuum chamber was enclosed by an 18-in.-diam by 12-in.-high Pyrex bell jar mounted on a stainless-steel base plate. Access holes in the base plate were used to supply argon gas to the chamber, to allow for various electrical feedthroughs, and to provide mechanical motion to the shutter between the source material and substrate. The chamber was evacuated by a pumping system consisting of a 720 liter per sec oil diffusion pump backed by a 13 cu ft per min mechanical pump. Ultimate pressures of less than 1 x 10-6 torr could be achieved. The substrates were securely mounted on the stainless-steel substrate holder by quartz tabs held in place by stainless-steel screws. Temperatures of the substrate holder were measured by a thermocouple inserted within the holder. A quartz lamp was used to heat the holder and temperatures as high as 420°C could be maintained. Deposition Conditions and Procedure. The substrates used were polished fused quartz slides 116 by 1-12 by 3 in. and were outgassed at 200°C for 1 hr at a pressure less than 1 x 10-5 torr before film deposition. This was followed by a presputtering period of 2 hr during which the movable stainless-steel shutter was so positioned that deposition on the substrate was prevented. At a sputtering voltage of 5000 v dc and an argon pressure of 0.03 torr, the cathode cur-

Jan 1, 1967

By E. A. Gulbransen, K. F. Andrew

Weight loss measurements were made using a sensitive microbalance operating in a high vacuum system. The Langmuir equation was used to Calculate the vapor pressures of the several metals and alloys. Aluminum lowered the vapor pressure of i9,on in a 5.4 Al-94.6 Fe alloy, and of iron and chromium in a 4.8 Al-21.5 Cr-73.7 Fe alloy. The influence of oxide films formed on the alloys on the effective vapor pressures of the alloys was also studied. These studies were used to aid in the inte9,pretation of the high temperature oxidation of alloys based on iron, chromium, and aluminum. RECENT studies on the oxidation of chromium1 and the heat resistant alloy 5 Al-22 Cr-73 Fe showed transitions in the rate of oxidation at 900o and 1050oC respectively. The transition for chromium occurred at a temperature where the rate of evaporation of chromium from oxide-free surfaces equalled the rate of chromium atoms reacting with oxygen. This paper presents new vapor pressure studies on iron, chromium, and the specially prepared alloys 5.4 Al-94.6 Fe, 21.9 Cr-78.1 Fe, and 4.8 Al-21.5 Cr-73.7 Fe. The ternary alloy is similar in basic composition to the patented heat-resistant commercial alloy known as Kanthal. The binary alloys were studied to show the individual effects of aluminum on the vapor pressure of iron and of iron on the vapor pressure of chromium. The purpose of the proposed studies was to test the influence of metal volatility on the oxidation behavior of heat-resistant alloys based on iron, chromium, and aluminum. Since oxide films formed on the metal may limit metal transfer to the surface, the influence of oxide films on metal volatility was also studied. LITERATURE A) Vapor Pressure. The vapor pressure of iron has been studied by Jones, Langmuir, and Mackay,&apos; Dornte and Nrton. Edwards. Johnston. and Ditmar. and McCabe, Hudson, and Paton. Stull and SinkeT have calculated a heat of sublimation at 298° K of 99.83 kcalper g atom. The vapor pressure of chromium has been reported by Bauer and Brunner,&apos; Speiser, Johnston, and Blakburn, Gulbransen and Andrew,&apos;&apos; Vintaikin,o McCabe, Hudson, and Paton, and Kubaschewski and Heymer.12 Good agreement was obtained except for the early work of Bauer and Brunner.&apos; Stull and Sinke7 calculate a heat of sublimation at 298°K of 95.0 kcal per g atom. Vapor pressure measurements on aluminum have been made by Brewer and Searcy,13 Bauer and Brunner,aand Farkas.I4 Stull and Sinke,7 giving Brewer and Seary&apos;s&apos; data the most weight, derive a heat of sublimation of 77.5 kcal per g atom at 298 oK. B) Method. Two methods15 are used for measuring the vapor pressure of metals: 1) The Langhuir free evaporation method, and 2) the Knudsen effusion method, In the Langmuir method, used in the present work, the vapor pressure of the metal P is given by the equation: Here M is the molecular weight of the vapor species. T is the absolute temperature. (dw/dt) is the rate of sublimation in g per sq cm per sec and a is the condensation coefficient. a is a measure of the efficiency of condensation of molecules striking the metal surface from the vapor. If condensation results from each collision a is unity. This coefficient has been found to be unity,a, le for metals. These results establish the general validity of the Langmuir free evaporation method as applied to metals. EXPERIMENTAL A) Vacuum Microbalance Method. A modification of the Langmuir free evaporation method was used. Strip specimens were suspended from a sensitive microbalance operating inside of a high vacuum system. For alloys, microbalance methods17 must be used on large area samples at relatively low temperatures to minimize composition changes. The

Jan 1, 1962

By C. Bachmann, M. J. Laurila, A. J. Widenman, A. Klein

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA&apos;s Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison&apos;s Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of online analyzers (ISO/DIS15239).

Jan 1, 1999

By K. Robertson, K. A. Scalise, K. C. Kocsis, M. B. Teixeira

"Many deep and highly mechanized underground metal mines require cooling. In many cases, appropriate working conditions might be fulfilled by ventilation alone, but some require the implementation of cooling systems. The most common cooling systems are bulk air cooling and localized cooling. These systems are effective, but they use considerable amounts of electricity. Ground source heat pumps (GSHP) can supplement existing cooling and heating systems, while geothermal systems can cool the mines in their entirety if there are significant sources of geothermal energy are present. A major advantage of geothermal and GSHP systems are their renewability, which reduces the carbon footprint of the mine.INTRODUCTIONThe western United States has abundant alternative energy sources including a high potential for geothermal energy. Geothermal utilization is a viable energy alternative that many areas throughout the world have access to because high geothermal potentials are located near areas of volcanic activity such as along plate boundaries, mid-oceanic ridges, rift valleys and hot spots (IRENA, 2017). There is significant potential to use geothermal energy for many applications. With constantly evolving and innovative technologies being developed, an increasing number of geothermal applications are becoming feasible. The western United States is an ideal candidate for alternative energy applications due to the geothermal availability and the emergence of modern technology. This paper investigates the incorporation of renewable methods and the alternative energy possibilities of Barrick Goldstrike, located in northern Eureka County, NV and Rio Tinto/BHP Billiton’s Resolution Copper mine located in Superior, AZ.RENEWABLE SYSTEMSGeothermal SystemsGeothermal temperatures are typically defined as either high or low temperature systems(Shengjun, Huaixian, & Tao, 2011). The high-temperature reservoirs (>220°C / 428°F) are feasible forlarge, commercial production of electricity with dry stream and flash stream systems (Shengjun, Huaixian, & Tao, 2011). Low temperature systems, below 220°C (428°F) (Shengjun, Huaixian, & Tao, 2011), aremuch more difficult to use for energy production. Low-temperature reservoir heat can be harnessedthrough the implementation of a binary cycle plant. The working fluid for a binary cycle plant is eitherorganic (Organic Rankine Cycle (ORC)) or an ammonia-water mixture (Kalina cycle). Organic fluids andammonia-water mixtures have low boiling points that allow for the recovery of heat from low-temperaturesources (Eymel Campos Rodriguez, et al., 2013). The efficiency of the binary cycle plant varies depending upon the fluid, thus the proper selection of the fluid is critical for maximum energy output"

Jan 1, 2019

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By Z. Sun, H. A. Davies

"Current understanding of the mechanisms by which glassy and crystalline thin ribbons are formed in high speed continuous casting processes is considered. A computer model of the combined heat and momentum transfer during melt spinning has been developed. The influence of roll velocity and of heat transfer coefficient (between the melt and the roll) on the temperature and velocity distributions within the melt puddle is analysed and the thickness of the extracted ribbon computed. The relative importance of heat and momentum transfer under different conditions is assessed and differences between the casting of crystalline and amorphous strip highlighted.IntroductionHigh speed continuous casting of thin metallic ribbon and strip is currently of considerable interest both to metal processers and to those studying process mechanisms. The practical interest arises both from the potential economic benefits to be gained from a shorter and more energy-efficient production route and from the ability to obtain extended and uniform thin strip having a metastable microcrystalline or amorphous structure with enhanced or unique properties. The latter arise from the rapid solidification associated with the cooling of very thin sections of melt brought into intimate thermal contact with one or two rapidly moving heat sinks.The principal processes for casting thin strip include free jet, chill-block melt-spinning (GBMS) (1), melt drag (MD) (2), planar flow casting (PFG) (3) and twin-roll casting (TRG) (4). For the first three of these, all essentially variants of melt-spinning, melt flows through a nozzle onto the circumferential surface of a rapidly rotating roll, whereas for TRG the melt passes into the nip between two contra-rotating rolls. We shall be concerned in this paper with the single-roll melt spinning processes only. For these, a puddle is established where the melt contacts the roll surface and the length of this puddle l is a function of the process conditions, notably the circumferential velocity of the roll Us and the volumetric flow rate of the melt Q. The contact time between any point on the roll surface and this puddle, or residence time eR(= l /Us) determines the thickness of ribbon t extracted from the puddle. This thickness, in turn, partly governs the cooling rate T and the amount of undercooling in the melt and thus the microstructure of the solidified ribbon."

Jan 1, 1986

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner&apos;s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head&apos;s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010