Search Documents

By S. G. Proctor, D. L. Baaso, W. V. Conner

A double crucible system was developed for I-g scale plutonium reductions. The equipment consists of an inner MgO crucible, an outer MgO crucible, and a stainless steel pressure vessel. The reduction charge is PIaced in the inner crucible and the annulus between the inner and outer crucibles is filled with a mixture of calcium and iodine. The exothermic reaction between the calcium and iodine in the annulus supplies the heat required for complete reaction of the reduction charge ana' good metal coalescence. Metal yields of 80 to 85 ,pct were obtained from I-g scale reductions and yields as high as 97.5 pct were obtained from 0.5-g scale reductions. The system was used to reduce charges containing as little as 0.1 g of Pu resulting in metal yields up to 90 Pct. THIN metal foils of highly enriched plutonium isotopes are used as targets for cross section and other measurements. The isotopes are separated in the calutrons at Oak Ridge and are very expensive to prepare. Often, only 1 or 2 g of material are available thereby emphasizing the need for a method of preparing these small quantities of metal. Procedures for 1-g scale plutonium reductions have been described, but these procedures require elaborate or expensive equipment. For example, the procedure described by Anselin et al.1 requires an inert atmosphere glovebox and induction heating equipment. The procedure described by Baker2 also uses induction heating equipment to obtain the recommended heating rates and liner temperatures. Baker's procedure also requires high purity PuF4 with very little PuO2 present. The procedure described in this paper resulted from a search for a simple and inexpensive method for making 1-g scale plutonium reductions. EXPERIMENTAL Equipment. The equipment required for the double crucible system consists of a pressure vessel, two MgO crucibles, a MgO crucible lid, and a resistance-heated, vertical crucible furnace. The crucibles were slip cast from high purity MgO and were supplied by the Coors Porcelain Co. and the Norton Co. The pressure vessel and lid were fabricated from 316 stainless steel. Materials. The PuF4 used for this study was obtained from the P1utoniu:m Metal Production Department at Rocky Flats. The PuF4 was prepared in a con- tinuous hydrofluorinator by reacting Pu02 with HF at 650°C. The isotopic composition of the plutonium was approximately 93 pct 239PU, 6 pct 240PU, and 0.5 pct 241PU. Some of this PuF, contained less than 1 pct Pu02 (Batch No. 6 and 7), while other batches contained up to 15 pct Pu02 (Batch No. 3). The chemical analyses of all the PuF4 used for this study is given in Table I. The calcium was 99 pct pure, AEC grade, and only that fraction which would pass through a 20 mesh screen was used. The I2 was USP grade re-sublimed I2 which was ground before being used. Procedure. Various charge compositions and methods for loading the double crucible system were tested. The optimum conditions for 1-g scale reductions are described below. The double crucible system was loaded as shown in Fig. 1. The outer crucible was placed in the pressure vessel and the annulus between them was filled with MgO sand. The inner crucible was placed in the outer crucible, supported by a layer of MgO sand in the bottom of the outer crucible. A mixture of 5.2 g of Ca and 25 g of I2 was placed in the annulas between the two crucibles. The upper portion of the annulas was filled with MgO sand. Next, a layer of a mixture of calcium and I, equal to 20 wt pct of the calcium and I2 used in the main charge was placed in the bottom of the inner crucible. The PuF, to be reduced was mixed with a 30 pct excess of calcium and 1 mole of I2 per mole of Pu and this mixture was placed in the inner crucible. The charge was topped with a layer of a mixture of calcium and I2 equal to 20 wt pct of the calcium and I2 used in the main charge. The pressure vessel was sealed with a flat copper gasket and was purged by alternately evacuating and filling with argon. The purge valve was closed and the vessel was placed in a vertical crucible furnace which was preheated to 950°C. The furnace was turned off after 20 min of heating and the vessel allowed to cool. Experience has shown that. this amount of heating is sufficient to assure complete reaction of the charge. RESULTS AND DISCUSSION The double crucible system has been used to produce plutonium metal on a 0.1- to 1-g scale. Reduction

Jan 1, 1970

By Benny J. Nelson

AS a part of the fundamental research program of Aluminum Research Laboratories, some data were obtained on the ternary system Mg-Al-Mn. As very little information on the magnesium corner of this diagram has heretofore been published, it seems desirable to make available the values found for the liquidus and solidus surfaces of this system. Procedure The settling procedure was used for the determination of the liquidus compositions. Metallo-graphic examination of quenched samples, and stress-rupture upon incipient melting, were used for the solidus determinations. The settling procedure has been described in a previous paper.' Briefly, this method involved saturating the alloy with manganese at a temperature substantially above that at which the sohbility was to be determined, then cooling the melt to the latter temperature, and holding it at that temperature for a substantial period of time. Samples for analysis .were carefully ladled from the upper portion of the melt at hourly intervals during the holding period. After the ladling of each sample, the melt was stirred to redistribute some of the manganese that had already settled, because it appeared that when the latter particles of manganese again settled, they aided in carrying down more of the manganese and thus hastened the attainment of equilibrium. The melts were prepared and held in a No. 8 Tercod crucible holding approximately 4 lb of metal. The manganese was added either in the form of a prealloyed ingot (Dow M) containing about 1.5 pct Mn or by the use of a flux (Dow 250) containing manganese chloride. In calculating the flux additions, it was assumed that the manganese introduced would be equal to 22 pct of the total weight of the flux. Temperatures were measured with an iron-constantan thermocouple enclosed in a seamless steel tube, the lower end of which was welded shut. This protection tube also served as a stirring rod. The samples ladled from the upper portions of the melts at the various intervals were analyzed for aluminum, manganese, and iron. When making the alloys which were to be used for the determination of the solidus, 2½ in. diam tilt mold ingots were cast, scalped to 2.0 in. in diam, and extruded into ? in. diam wire. The principal impurities in the melts for this investigation were iron and silicon; their total not exceeding 0.03 pct. Portions of the wire, approximately 2 in. in length, were enclosed in stainless steel capsules for protection from the atmosphere. Bundles of these capsules, with a dummy capsule containing an iron-constantan thermocouple, were heated inside a large steel block (acting as a heat reservoir) in a closed circulating-air type electric furnace. At ap- propriate times, the capsules were removed and quenched in water. The wires were examined metallographically to determine the temperature of initial melting. Short times at temperature were used at the beginning for wire specimens of all alloys to obtain quickly the approximate temperatures at which melting could be first observed. When approximate solidus temperatures had thus been determined, equilibrium heating was attempted. This equilibrium heating consisted of an 8 or 16 hr period at a temperature, about 50 °F below the lowest temperature at which melting occurred when short heating cycles were used, followed by further heating for 1 hr periods at consecutive 10" higher temperatures. The theory for the method of stress-rupture at incipient melting has been well covereda and its limitations are recognized. Thus, if the interfacial tensions are such that the first minute quantity of liquid is "bunched up" at the grain boundary junctions instead of spreading out along the grain boundaries,³ temperatures higher than the solidus are required before melting will be manifested by rupture of the specimen. This point will be elaborated later. Specimens of the wires with a reduced section (approximately 1/16 in. diam) were suspended vertically in a tubular furnace. The setup used is shown in Fig. 1. The clamp holding the specimen was made from alumel thermocouple wire and the thermocouple was thus completed across the specimen by attaching a chrome1 wire to its lower end. Temperatures were read from a Speedomax recorder used in conjunction with a calibrated thermocouple. The small weight attached to the specimen and a vibrator attached to the furnace tube, to aid in distributing the molten constituent along the grain boundaries, were used to bring about rupture at a temperature closely approximating the solidus. The specimens were heated at a rate of about 5°C per min. The rupture of the specimens was indicated both by sound and by the action of the recorder. An argon atmosphere containing a small amount of SO² was used for protection of the specimen. The assembly was taken out of the furnace immediately following rupture and the specimen removed. Some of the broken specimens were examined metallographically and will be referred to later. Results and Discussion Fig. 2 shows a set of typical time-composition curves for liquid samples of the Mg-Al-Mn alloys used for the settling tests. The data as presented

Jan 1, 1952

By P. Chiotti, G. R. Kilp

Thermal, metallographic, vapor pressure, and X-ray data were obtained to establish the phase diagram for the zinc-zzrconiz~m system. Five compounds corresponding to the stoi-chiometric formulas ZrZn, ZrZn,, ZrZn,, ZrZn,, and ZrZn14 were observed. All these compounds, with the exception of ZrZn2, which melts congruently at 1180°C under constrained zinc-vapor conditions, undergo pexitectic reactians. The temperature at which the zinc vapor pressure is I atm for a series of alloys was determined from vapor-pressure measurements. The data obtained are summarized in the construction of a I-atm-pressure phase diagram and a phase diagram corresponding to a pressure of less than 10 atm. THE purpose of this investigation was to establish the phase diagram for the zinc-zirconium system. Thermal, metallographic, vapor pressure, and X-ray data were employed in determining the phase regions. Partial investigations of this system have been conducted by Gebhardt1 and Carlson and Borders.' Carlson and Borders studied the high-zirconium region and established the existence of a eutectic at 69 wt pct Zr with a melting point of 1015°C. The terminal phases of the eutectic horizontal were shown to be an intermetallic compound ZrZn and a solid solution of ß zirconium containing 21 wt pct Zn. The ß solid solution decomposes into ZrZn and a zirconium at 750°C. The eutectoid composition is given as 15 wt pct Zn, and the solubility of zinc in a zirconium at temperatures below 750°C is indicated to be negligible. Gebhardt studied the zinc-rich region and observed a lowering of the melting point of zinc from 419.5" to 416°C and temperature horizontals at 545" and970°C. Some preliminary observations by Chiotti, Ratliff, and Kilp were reported by Hayes.2 pietrokowsky3 has reported the compound ZrZn2 to have a cubic MgCu2 structure with ao = 7.396A. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc or Baker analyzed reagent granulated zinc, both 99.99 pct pure and hafnium-free iodide-process crystal bar zirconium obtained from the Westinghouse Electric Corp. The zirconium contained 200 ppm Fe, 200 ppm Si, 100 ppm C, and minor amounts of other impurities. The zirconium was milled or machined into thin chips or shavings. These were cleaned with a nitric-hydrofluoric acid solution, rinsed with water, and acetone, and dried just prior to their use in alloy preparation. The granulated zinc was similarly cleaned using dilute nitric or hydrochloric acid. Weighed quantities of these materials, 20 to 30 g total, were mixed and pressed at 20,000 to 70,000 psi to give relatively dense compacts. During the early part of this investigation the pressed compacts were placed in MgO-15 wt pct MgF, crucibles which were then sealed inside of quartz ampules. The compacts were given various prolonged heat treatments prior to their use for thermal analyses, or vapor-pressure measurements. Because of expansion of the compacts and the relatively high zinc vapor pressure it was difficult to heat to the melting temperatures of the alloys without failure of the quartz ampules. Homogenization at temperatures below the melting temperature gave brittle, porous alloys unsuitable for metallographic examination. It was also difficult to prevent condensation and segregation of zinc on the colder parts of the quartz ampules during heating and cooling operations. These problems were eliminated to a great extent by the use of tantalum crucibles. Tantalum proved to be a satisfactory container with little or no reaction between the alloys and the tantalum. Small tantalum thermocouple wells were successfully welded in the bottom of these crucibles. Pressed compacts were sealed inside the tantalum crucibles by welding on preformed caps under an argon atmosphere. Heat treating and differential thermal analysis were combined into a single operation. The experimental sample assembly is shown in Fig. 1. This assembly was enclosed inside a stainless-steel tube heating chamber which could be evacuated and filled with an inert gas. The thermocouple leads were brought out of the heating chamber between two rubber gaskets used to provide a vacuum seal for the water-cooled head. Most of the compounds in this system undergo peritectic decomposition. After heating above the temperature of a particular peritectic horizontal the sample was cooled to just below the peritectic temperature and held at temperature for several hours. The sample was then reheated through the peritectic temperature and the size of the thermal arrest, if still present, compared with the one previously obtained. If the thermal arrest was not characteristic for the alloy composition being investigated its magnitude diminished and repeated cycling and annealing eventually eliminated it. The peritectic thermal arrests characteristic of a particular composition were established in this manner.

Jan 1, 1960

By L. C. Michels, O. G. Ricketts

The disorientations between s?nall grains, whose growth has been arrested at an early stage of recrys-tallization, and the deformed matrix in cold-rolled aluminum single crystals were determined using transmission Kikuchi line and electron diffraction patterns. The orientations of the recrystallized grains were found to be random, and the disorientations of these grains with the matrix weve found to be intermediate to large. This leads to the conclusion that the observed vecrystallization began in small areas of large disorientation present in the cold-worked structure. heavily cold-worked thin sections of aluminunz single crystals and of polycrystalline aluminum and nickel were produced directly by a mechanical technique. The specinlens thus prepared were heated with the electron beam to bring about vecrystallization during observation in the electron microscope. Motion pictures taken du.ring heating and the electvon, microg.raphs taken both before and aftev heating allowed the recrystallization process to be traced to its ovigin. Re cvystallized grains originated in very s,mall regions of the cold-worked structure and developed through rapid migration of high-angle boundaries. The boundaries either were present as such in the matrix or were formed out of dense dislocation networks. SIGNIFICANT advances have been made in recent years in the study of nucleation of recrystallization using the technique of transmission electron microscopy of thin metal foils. Bollman1 in a study of heavily rolled polycrystalline nickel found support for the Cahn-Cottrell2,3 theory of nucleation. According to this theory nuclei form by the initially slow growth of subgrains formed through polygonization. During this initial period of slow growth (the incubation period) the migrating boundary of the subgrain increases its disorientation with the cold-worked matrix and thereby increases its mobility to become a rapidly migrating high-angle boundary. Bailey4,5 investigated the annealing behavior of several metals deformed both in tension and by rolling and concluded that recrystallization took place through the migration of high-angle boundaries. With low deformations these boundaries were present in the metal before deformation. With high deformation it was not possible to tell whether the boundaries were pieces of the original grain boundaries or were produced either during deformation or by polygonization during ameal- ing. Direct observation during heating of metal foils indicated that subgrains form by polygonization and grow at an uneven rate. The grain size obtained decreased with decreasing foil thickness indicating that the foil surface resists boundary motion. Votava,6 in heating stage experiments on rolled copper, observed nuclei to appear suddenly and grow in jumps of differing magnitude. However, he found no special dislocation configurations where the nuclei appeared. Fujita,7 as a result of a study of subgrain growth in heavily worked aluminum, concluded that the boundary of a recrystallized grain initially forms from the boundary of a group of subgrains. This occurred by a process of deposition of vacancies and dislocations in the group boundary as the boundaries within the group disappear. HU8,9 directly observed a similar process in heating stage experiments on 70 pct rolled Si-Fe single crystals. The growth of subgrains appeared to proceed by a coalescence mechanism. The observed fading away of the boundary between two subgrains was explained by the moving out of dislocations from the disappearing boundary into the connecting or intersecting boundaries around the subgrains. The subgrain size and degree of disorientation with the surrounding structure were thus increased. With the increase in disorientation occurred a corresponding increase in boundary mobility, which eventually allowed the boundary to migrate rapidly. This process was observed to occur within "microbands" consisting of parallel narrow segments disoriented by a few degrees present in the as-rolled structure. The conclusion of Rzepski and Montuelle10 that growth is preceded by the coalescence of blocks through disappearance of their common boundaries supports this view. In contrast to Hu's coalescence model for nucleation were the conclusions of Walter and ~och.""~ Working with the same material as Hu, of the same orientation and rolled to the same reduction, they concluded that nucleation occurred by the Cahn-Cottrell mechanism. They observed, in agreement with Hu, that recrystallization began in the "microband" regions which they referred to as "transition" bands. Bartuska13 studied subgrain growth in heavily rolled nickel using a beam heating method in the electron microscope. He concluded that nuclei for recrystallization form from the largest most perfect subgrains present in the cold-worked structure by rapid intermittent migration of parts of subboundaries. In rare instances he observed subgrain growth by coalescence. EXPERIMENTAL PROCEDURE The materials used in this study were 99.999 pct A1 supplied by A.I.A.G. Metals, Inc., and 99.999 pct Ni supplied by Johnson and Matthey and Co., Ltd. The Hitachi HU-11 electron microscope, with uniaxial

Jan 1, 1968

By C. Sensogut

The phenomenon of spontaneous combustion is one of the major hazards encountered in underground coal mines both from the safety aspects and on economic grounds. Every occurrence, however small, if not tackled effectively in the early stages can develop into open fire, or explosion of gas or coal dust. In terms of economy, even dealing with small incidents may be costly in terms of labour and materials, and in case of a sealing off of a district being necessitated, the loss of face equipment and sterilization of reserves is potentially great. Therefore, expense and effort in prevention and detection of such heating, together with a high state of readiness for dealing with likely event, is completely justified and may be considered as a sound investment. In order to achieve this investment, it may be worth to pinpoint the centre of the fire occurring due to autogenously heating which is supposed to be great assistance to inert it at a least cost and time. Therefore, it is the aim of this work to model the spontaneous combustion in the goaf.

Jan 1, 2002

By Hon-Yim Ko

1972 constituted the second year of the projected five-year study on constitutive relations of coal. The schedule adhered closely to the five-year outline which is summarized in Table 1. This chapter is intended to serve as introduction and concise synopsis of the year's activities and results, which are presented in greater detail in the following chapters, which have been contributed by the individual researchers in charge of the various aspects of the project under study. Coal Sources, Material Procurement, and Sample Preparation Most of the studies performed during 1972 were done on coal from two sources: the Old Ben Mine #22 in Illinois, and the Bruceton Mine in the Pittsburgh seam of Pennsylvania, which may be considered typical of coal sources of economic importance in the Midwestern and Eastern part of the U.S. These two mines have proven to be reliable suppliers of coal material for our research. We have been able to establish good working relations with their personnel and feel that we can continue to count on their cooperation and help.

Jan 1, 1972

By M. C. Udy, F. W. Boulger

AN incomplete phase diagram for the U-Ti systern was determined earlier 1 and more recently, a tentative diagram was presented for the uranium-rich end of the system.' In the present re-examination of the whole system of U-Ti alloys, high purity materials were used. Melting stock for the alloys was high purity uranium, containing about 0.09 pct C as the only appreciable impurity, and high purity iodide-process titanium purchased from New Jersey Zinc Co. Both metals were cold rolled to about 1/6 in. thickness, sheared to about I/' in. squares, and cleaned by pickling. The alloys were arc melted under a helium atmosphere in a water-cooled copper crucible. A thoriated-tungsten electrode was used. The furnace chamber was evacuated, then flushed with helium, prior to each melting. It was finally filled with stagnant helium at one atmosphere pressure. Each alloy was remelted three times after the original melting, to insure homogeneity. The alloy button was turned bottom side up before each re-melting operation. Some 22 alloys were examined. Their compositions were spaced at appropriate intervals between 100 pct Ti and 100 pct U. Analyses were made on chips taken after fabrication. The major contaminant was carbon, which varied from 0.03 to 0.08 pct. It appeared in the microstructure as titanium carbide. Alloy compositions were calculated to a carbon-free basis for consideration on the diagram. Tungsten and copper, possible contaminants from the melting operation, were generally less than 100 parts per million each. Fabrication All alloys were forged and rolled to bars approximately V8 in. square. They were clad either in SAE 1020 steel or in a 5 pct Cr-3 pct Al-Ti-base alloy, depending on the fabrication temperature. A temperature of 1800°F (980°C) was used for alloys near the compound composition. This necessitated using the titanium-base alloy, since iron reacts with titanium at this temperature, producing a low melting alloy. Other alloys were fabricated at 1450°F (790°C), using steel jackets. No iron-titanium reaction occurred at this temperature. The jackets were welded in place in an argon atmosphere. Those alloys sheathed in steel were declad and then reclad between rolling and forging operations. On the other hand, those clad with the titanium alloy were cut to a roughly rectangular shape prior to clading and were then carried through both the forging and rolling operations without opening. Those alloys near the compound composition were found to be cracked when the clading was removed. The cracked materials had been plastically deformed, however, and at least some of the cracking had OCcurred during cooling. Heat Treatment The rolled bars, after being declad and shaped to remove surface contamination, were all given an homogenizing treatment of 160 hr at 2000°F. (Samples were taken for analysis following the declading and shaping operations.) All were heat treated at the same time in one furnace, but each was sealed in a purified argon atmosphere in an individual Vycor glass tube. Argon pressure was such that it was approximately atmospheric at temperature. One end of each tube contained titanium chips and this end was heated to 1200°F (650°C) for 10 min prior to the heat treatment. This purged the atmosphere of residual reactive gases. The balance of the tube was warmed during the purge to liberate adsorbed moisture and gases, which also reacted with the hot chips. The bars were furnace cooled from the homogenization treatment. Specimens of each alloy were water quenched after 2 hr heating at 1000°, 1200°, 1400°, 1600°, 1800°, and 2000°F (540°, 650°, 760°, 870°, 980°, and 1095°C). In addition, some were treated at intermediate temperatures of 1300°, 1500°, and 1700°F (705", 815", and 925°C) and at 2150°F (1175°C). Specimens, about '/s in. cubes, were cut from the bars, sealed in individual Vycor tubes, and heat treated as described. All specimens heat treated at the same temperature were processed together. Samples were quenched by breaking the Vycor tube rapidly under water. Metallographic Examination Specimens were mounted in bakelite and ground wet on 180 grit paper held on a 1750 rpm disk. They were then ground wet by hand, using 240, 400, and 600 grit papers. The rough grinding was continued long enough to get well below the surface. Specimens were mounted separately because of the variation in the rate of etching between alloys. The specimens were polished with rouge on a 4 in., 1725 rpm wheel covered with Miracloth. Alloys on the titanium side of the compound composition were etched with a solution of 2 pct hydrofluoric acid in water saturated with oxalic acid. A few crystals of ferric nitrate were added as a bright -ener. Specimens were immersed 5 sec, polished to remove the etch, then re-etched. With the higher titanium alloys, it was often necessary to start the etch on the polishing wheel, because of the formation of a passive film. In some instances, a plain 2 pct hydrofluoric etch was satisfactory. For the alloys on the uranium side of the compound, a distinction between the compound and the uranium phase developed after standing a short time in air. This could be hastened by the application of heat, such as obtained by placing the specimen on a radiator. A deep etch was necessary to develop details in the uranium-rich phase, such as the Widmanstaetten pattern sometimes obtained by quenching y uranium. A 2 pct hydrofluoric acid solution was used for this deep etching.

Jan 1, 1955

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By AIME AIME

Do you Possess, or Can you Obtain; and Will you Give, or Sell, to the Institute Library Early Volumes of the following Proceedings and Journals? American Chemical Society. American Foundrymen's Association. Australian Mining Standard. Chemical Society of London. Deutsche Chemische Gesellschaft. The Foundry. New Zealand Mines Record. Queensland Government Mining Journal. La Revue Universelle des Mines.

Jan 9, 1907

By K. C. Viveros, R. R. Ambriz, C. García, F. De Villèle, A. Talha, D. Jaramillo

Cold hole expansion on base metal, weld metal and heat affected zone of 6061-T6 aluminum alloy welds was simulated by means of finite element method. Three dimensional compact test models with a previous fatigue crack length with a relation of ??= a/W = 0.3, were used to analyze the hole expansion process. Considering the local mechanical properties for each zone of the welded joint, the optimal expansion degree (1.64 to 2.46 %) was determined. The residual stress field, through thickness, after the expansion process in all welding zones, were correlated with the crack opening displacement obtained by finite element analysis. It was observed, that compressive residual stress fields for a post-expansion, in different crack lengths, provided a crack closure mechanism for base metal, weld metal and heat affected zone. Contrary, the crack remained open when residual stresses are positive. The results are given as tangential stresses versus distance from the edge of the cold expansion and crack opening displacement as a function of applied load.

Jan 1, 2014

A mineral grain finder is described which is easily constructed to fit onto the stage of a standard reflected light ore microscope.The device is most useful in relocating particular grains or mineral associations on 30 mm diameter polished sections. The use of the grain finder in the teaching of ore microscopy is outlined.

Jan 1, 1988

By Steve Dillingham

In recent years, there has been a trend toward increasingly demanding blasting standards being enacted by local and regional regulatory authorities. The objective of this paper is to alert blasters of the difficulties that are created for blasting projects as a result of these restrictions, as well as the steps that can be taken to minimize future conflicts.

Jan 1, 1995

By A. A. Hazell

Mine management by objectives by A. A. Hazel The procedure of setting production targets is illustrated in Appendix I of the paper. This procedure is intended only as a guide although the standards on which it is based were established by work studies and found subsequently to be well within the limits of a trained crew.

By Johnson MT

The microprocessor revolution of the 1970's dramatically improved the price/per- formance of graphics hardware. Together with improved communications and new software concepts and standards this has resulted in the emergence of a new tool with particular application to the mining industry. The Distributed Graphics Processor (DGP) offers more natural means of interaction with com- plex technical models.

Jan 1, 1983

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

By Paul Worsey, Matthew K. Coy

New blasting mat designs are currently tested in the field on actual blasting jobs and only undergo qualitative rather than quantitative assessment. The majority of matted blasting occurs in trenching in which the blast designs and field conditions vary considerably. In order to assess a new blasting mat material and design, a new standard test was devised.

Jan 1, 2015

By Ellson I. G

Advantage has been taken of the need to build the new mining town of Shay Gap to incorporate a new standard of living in an isolated area, which suffers from climatic extremes. The various problems associated with living in the Pilbara area of Western Australia are outlined, together with their effect on the design of Shay Gap.

Jan 1, 1973

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By David Mandolesi

An examination has been made of the structures of strand cast blooms and the rails rolled from them; this paper details the characteristics of these typical structures. Results of mechanical testing data show that this product compares with rails processed from conventional ingot steel. Improvement in processing yields and surface quality standards are also briefly discussed.

Jan 1, 1972