Search Documents

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

By Edmond Donovan, O&apos

With the increase in complexity of conveyor systems and the inexorable demand for more capacity and availability, the ability of designers to accurately predict performance is becoming increasingly important. Dynamic analysis techniques for modelling wave mechanics in conveyors are finding increased applications. Unfortunately, the reliability of these modelling techniques is dependent on a thorough understanding of the performance characteristics of the components that make up the system. These characteristics include such things as response rate, hysteresis and efficiency. Some parameters such as idler rolling resistance can be easily quantified by measurement. More complicated drive parameters are difficult or impossible to measure, particularly in large horse-power equipment. One method of quantifying or at least bracketing the performance envelope of complicated pieces of equipment is to construct a mathematical model. This can be done quickly and economically, and the influence of various parameters can be determined. This paper sets out to demonstrate by example the usefulness of this technique in gaining an understanding of complicated systems. The model is developed and the influence of a number of variables are examined.

Jan 1, 1996

By M. H. Basiri

Crude oil, as a central commercial commodity, is tied to major economic activities in all nations. Also its price fluctuation plays a significant role in global political and economic situation, as a change in the price invariably affects the cost of other goods and services. Therefore reliable forecasts of the price of oil are interest for a wide range of applications. Several approaches have been proposed over the past few years. These may divide into three categories; artificial intelligent, statistical techniques and hybrid methods. The neuro-fuzzy is one of the sub divisions of hybrid method, containing neural network and fuzzy techniques. In this paper a novel forecasting model based on adaptive neuro-fuzzy inference (ANFIS) is proposed to predict monthly crude oil price. To be able to train and test the model, the statistical data from 1990 to 2010, was obtained from West Texas Intermediate oil prices. The results are compared with a multi criteria regression analysis, it is demonstrated that the neuro-fuzzy lead an accurate and more promising forecast.

Jan 1, 2012

By P. Massacci, F. La Marca, G. Bonifazi

Some deposits of inhomogeneous materials, which occur near the surface and are exploitable by open-pit mining, may he characterized in real time prior to mining through groundsurface imagery. If the slice to be stripped is not overly thick, surface texture and color properties may be extrapolated to its entire thickness. Image-analysis techniques for processing ground-surface images acquired in situ or in the laboratory shortly after their acquisition have been developed. These images yield pattern vectors representative of red, green and blue (RGB) color component distributions and hue, saturation and brightness (HSB) texture parameters. The techniques were applied to a sandy ore deposit containing three lithotypes. Geostatistical analysis indicated that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multibarycenter classification algorithm. Such in situ image-analysis procedures provide a means for selecting the ore to be mined, selecting the proper ore-processing method and determining the appropriate blend to he processed. This can be done either before or during mining.

Jan 1, 2000

By A D. Bugarski, B R. Conard, G H. Sc

The objective, of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at IncoÆs Stobie mine, was to conduct a long-term field evaluation of selected diesel particulate filter (DPF) systems, available to the underground mining industry. Nine state-of-the-art DPF systems were retrofitted to heavy-duty and light-duty vehicles and were subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (in 2001, 2002 and 2004) to establish in-use efficiencies and durabilities of the tested DPF systems. During efficiency tests, the vehicles/engines were operated over several steady-state operating conditions. Various instruments were used to measure particulate and gaseous emissions upstream and downstream of the filter systems. The results were used to assess the effects of the filter systems on the concentrations of diesel particulate matter (DPM), nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. Experience with the operational issues related to deployment of the filter systems on underground mining vehicles, coupled with the assessment of the filtration efficiencies, were the primary objectives of the study. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate the advantages and disadvantages of the various types. Some of the major issues studied were criteria for selecting the filter media, means of regeneration, the long-term operational reliability, and the occurrence of unwanted secondary emissions.

Jan 1, 2005

By David T. Swanson

The term "pressure tunnel" in the broad sense includes all hollow spaces, aligned along an axis and surrounded by rock, which are suitable for pressurization. In particular, this category includes: • horizontal or slightly inclined water pressure tunnels; • vertical or inclined pressure shafts; • pressure chambers or shafts of surge chambers; and, • compressed air storage tunnels. The main problems in the design and construction of pressure tunnels result less from their length or size than from the requirement for watertightness and, dependent upon this, reliability in operation and economy in construction. Where the lack of sufficient overburden does not permit the rock to accept the internal pressure in the tunnel, or where this pressure is so high that the watertightness is in doubt although the stability of the tunnel shell is not in question, a pressure tunnel must nevertheless be reinforced. Surge chambers, pressure tunnels and tailraces which are subjected to relatively low internal pressure, usually not much in excess of 1.5 MN/m2, are eminently suitable for construction in post-tensioned concrete. Pressure shafts, which as a consequence of the high water head are subject to a considerable maximum service pressure, are usually lined with a steel tube, a considerable proportion of the internal pressure being transmitted to the rock by backing concrete. TYPES OF LINING FOR PRESSURE TUNNELS In general, the type of lining will depend upon the nature of the rock. As a result, pressure tunnels usually are not uniform in con-

Jan 1, 1981

By L D. Lawrence, R S. Day, Gordon Coleman

Commercial emulsion explosives are typically characterized by their relatively high detonation velocities due to the intimacy of oxidizer and fuel and to their sensitization with glass microballoons. However, numerous blasting operations in softer, more porous rock formations are better fragmented with slower shooting explosives. Although mixtures of emulsions with large amounts of ANFO (60-80%) can considerably reduce the high velocities, little water resistance is achieved with low levels of emulsion blended with ANFO. "Water proof" blends containing typically 50 percent of emulsion become quite costly due to escalating powder factors in ANFO patterns. Blends of sensitized emulsions with 20-30 percent ANFO retain the high velocity characteristics of the emulsions as well as increased densities which can also adversely affect blasting results in softer rock formations. The introduction of a reliable and predictable on-site gassing process for sensitization and density control of repumpable emulsions, with or without added ANFO, offers the end user the option of supplying a final product more suited to his blasting needs. The capability to widely vary final product loading densities and consequently product detonation rates better tailors the final explosive to different rock characteristics. The beneficial advantages of this system in softer rock formations have been well documented. Overall comparison between these variable density products with typical repump emulsions containing solid density control will be reviewed. Besides the obvious cost advantages and safety advantages of these systems the end user is provided more definitive control of his blasting operation.

Jan 1, 1990

Access to secure and reliable water resources is fundamental to the minerals industry. In recognition of that requirement, and cognisant of extensive contemporary public water debate and reform initiatives in Australia, the Minerals Council of Australia (MCA) approached the Ministerial Council on Mineral and Petroleum Resources (MCMPR) proposing the establishment of a Joint Working Group to prepare a framework of strategic principles to ensure responsible water management at a site and corporate level, manage risks and identify opportunities. The Framework provides high-level guidance on issues that should be addressed in water decision making across Australia in relation to mining and associated processing operations. It identifies principles and objectives for adoption in four areas, viz: valuing water, strategic water planning, implementation, and engaging stakeholders. Given the high level nature of the Framework, and its national application, it does not seek to replicate detailed guidelines already widely available in each state and territory on operational water management practices and associated regulatory issues at mine sites. The Framework includes a series of case studies from across Australia that demonstrate where strategic thinking, wise water management and close consultation with stakeholders has delivered better water use, more profitable operations and excellent community/stakeholder relationships. The Framework was formally launched on behalf of MCMPR by the Western Australian Minister for Resources at the MCAÆs Sustainable Development Conference in Perth in October 2006. No full paper available for this extended abstract

Jan 1, 2006

Epithermal deposits have been defined as the lower temperature end of a spectrum of hydrothermal mineral deposits and are inferred to have formed near the EarthÆs surface. The preservation of an epithermal gold deposit in an Archaean craton is rather problematic, especially when such deposits form clusters or groups as reported for the Pilbara and Yilgarn cratons. For two of the better studied examples of epithermal gold deposits in these cratons, Becher and Wiluna, the evidence that they formed near the Earth surface is non-diagnostic, and the epithermal origin appears uncertain. Despite the simplicity of the original definition, there have been numerous errors in classifying epithermal gold deposits. It is suggested that these errors are primarily due to poor criteria defining the group as there is limited evidence of poor observational science being the cause. The criteria being used to recognise epithermal gold deposits include tectonic setting, ore element suite and quartz vein textures. None of these are diagnostic of epithermal deposits and their link back to the original low pressure-temperature definition of the class is tenuous. There has been definition creep over time as new observations on potential epithermal gold deposits become accommodated within a flexible definition. There is some urgency establishing and then using criteria to reliably identify epithermal deposits. Distinction of epithermal gold from weathered gold deposits is an important step. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Geoff C. Knight

Longwall mining using the shearer is acknowledged internationally as the most economically successful method of high volume production from underground coal mines. Since its introduction in the 1950s, a great deal has been achieved in developing the capability and reliability of the shearer - and the associated face conveyors and powered roof supports - to produce the competent systems now widely deployed. Equipment will continue to improve as knowledge and experience are gained and through the influence of market forces on the international equipment suppliers. However, current systems are so successful that further improvements are likely to be incremental rather than radical unless a high level of system automation is introduced. The automation concept is not new to the shearer-based longwall system. The opportunity and the need were recognized soon after the shearer and powered support were introduced in the 1950s. In the early 1960s, the British Coal Corp. (BCC; then the National Coal Board) attempted remotely operate longwall systems. Those imaginative early schemes were seen as failures at the time. But, with hindsight, a great deal was learned from the experience that stimulated automation research in several European countries. One of the most fundamental lessons learned was that coalface system automation is not possible until there is a high level of competence in automatically controlling the operation of the production machine itself within the coal seam. Once that is achieved, the rest of the system will follow with comparative ease.

Jan 1, 1991

By Richard M. Levine

Now that the former Soviet Union has divided into 15 countries, it is necessary to analyze separately the industrial mineral position of each of these countries. Industrial mineral data The former USSR was one of the world's largest producers of industrial minerals and had some of the world's largest reserves. Production and reserve figures, however, must be qualified. Even when these figures were reported by the Soviets, it was not clear that the production figures were for products that would be equally marketable in a competitive market economy. The reserve figures are based on the Soviet system of reserve classification, which is not directly equatable with the US Geological Survey and US Bureau of Mines classifications of economic reserves in market economy countries. The Soviets reserve classification system, in terms of which reserve figures will be given, is based on the reliability of the quantity of the material in place. The Soviet system assigns each occurrence to one of seven categories A, B, C1 and C2 are considered reserves; P1, P2, and P3 are considered resources. Mining in the former Soviet Union was authorized on the basis of the reserves in place in categories A, B and C, which had to be in prescribed ratios. However, the categories A, B and C do not necessarily correspond to Western concepts of material economically exploitable under present market prices with existing technologies.

Jan 1, 1992

By Frank Rausche

Although Quality Control (QC) during construction is preferable for deep foundations, there are many instances when it is necessary to resort to Quality Assurance (QA) methods if, for various reasons, QC is not possible. Non Destructive Testing (NDT) methods for deep foundations are indirect approaches, i.e. in complex situations they do not provide complete information and need to be augmented by additional testing and/or analyses. While the challenges are varied for the different deep foundation types and the different test methods they are the same in many different countries. Experience of the tester is often mentioned as being most important for a successful quality assurance. In addition, reliable testing equipment for the best possible measurements and complete construction documentation for a meaningful data interpretation are minimum requirements for a successful test outcome. Another problem is the widely varying cost of the QA tests. For that reason the specifying engineer or authority has to be aware of what can reasonably be expected so that technically feasible specifications can be written for optimal cost and minimal construction delays. This paper discusses the most common NDT methods with a view on how these methods are applied world wide. It summarizes features of specifications, recommendations for test procedures and advanced analysis methods which can help to overcome uncertainty in the quality assessment of the foundation. Finally, the authors propose a decision tree for various QA methods, deep foundation types and soil properties.

Jan 1, 2008

By V. R. Garflas, J. W. Ristori, R. V. Whetshel

Preliminary estimates indicate that world consumption of petroleum products and related fuels in 1937 shattered previous records with a figure of 1,920,000,000 bbl.; that is, 124,000,000 bbl. more than the 1936 total. The writers, as in previous years, have been unable to account for all the available supply in 1937. This "unaccounted-for" supply, which formerly was thought to go largely into storage in foreign countries, was close to 53,000,000 bbl. in 1933; 93,000,000 in 1934; 111,000,000 in 1935; 75,000,000 in 1936 and 148,000,000 in 1937. As this discrepancy between supply and demand continued year after year, it became evident that other reasons than additional foreign stocks were responsible for it. It can now be stated that the "unaccounted-for" supply (see Table 1) goes to take care of: (1) consumption of petroleum products and related fuels for military purposes, the figures of which have been and are kept confidential by foreign countries, (2) additions to stocks to be consumed for military and nonmilitary purposes in foreign countries on which likewise no information is available, (3) errors incurred in the conversion of figures of production of crude oil, its products and related fuels from "weight" units, as used in Russia, for instance, to their American or "volume" equivalents and vice versa, and (4) to the lack of reliable statistics on production and consumption, particularly from Russia, the

Jan 1, 1938

By Charles D. Litton

Experiments were conducted to determine the optical scattering properties of diesel particulate matter (DPM) and various combustion aerosols from both flaming and smoldering combustion sources at discrete angles of 151 and 301 in the forward direction and at a light source wave length of 635 nm using a simple light scattering module. In addition to the scattering data, simultaneous measurements were made of the total aerosol mass concentration; light extinction at an average wave length of 546nm; and the response of a common bipolar ion chamber typical of residential smoke detectors modified to allow the aerosols to flow through the chamber. The results of these experiments indicate, for DPM and combustion aerosols, the intensities per unit mass concentration depend not only upon whether the aerosolis DPM or combustion aerosol but also upon the type of combustion aerosol. The results also indicate that the ion chamber responses are greatest for DPM, followed by the response to flaming combustion aerosols (FCA)and lowest for smoldering combustion aerosols (SCA). For light scattering, the greatest intensities are found for SCA, followed by the intensities from FCA, and lowest for DPM. This report describes the experiments, their results, and the use of these results to developed sign criteria for early warning fire sensor capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by the products produced from diesel engines. © 2002 Elsevier Science Ltd. All rights reserved.

By T Hodgkin

The WA Goldfields is a highly productive gold and nickel mining area, but is arid with highly saline groundwater. Groundwater is widely used to supply process water to mines in the region but high groundwater salinity, commonly exceeding 50 000 mg/L TDS, tends to increase processing costs, limit end uses for the water, cause problems with disposal and potentially increase impacts on a sensitive arid environment. The area has low rainfall (200 - 270 mm/year) but run-off, particularly during cyclonic events, is high. Our experience suggests that stream flow from catchments in the area can produce a divertible yield of 8 - 17 ML/km2/year. An evaluation of stream flow harvesting using AnglogoldÆs Jubilee Pit predicted that 1000 ML/year of good quality water could reliably be supplied to the Sunrise Dam Gold Mine. Because of high rainfall variability, it is likely that an alternate source of water supply will be necessary when operating a surface-water harvesting scheme in the WA Goldfields. However, a combination surface/groundwater supply could have substantial cost, operational and environmental benefits compared to traditional supply systems that utilise groundwater only.

Jan 1, 2003

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By Heinz W. Duddeck, Hans-Konstantin Nipp

The design of storage space or deep mining in rock salt should take into account not only time dependency of the rock salt behavior but also temperature effects. For deep mining of potassium salt the natural increase of temperature with depth may no longer be negligible. For the storage of cryogenic liquid gas in salt caverns more knowledge is nezded about the propagation of deep temperatures and their effects on the stress-strain-creep behavior of the surrounding salt. High temperature problems arise for nuclear waste storages in caverns or drill holes emitting radiation. A numerical model is proposed for the analysis of displacements and stresses including their time and temperature induced change. For the material behavior of salt constitutive equations are chosen composed of a combination of Hooke-Kelvin-Bingham-Newton-model based on experimental results (excluding at present deep cooling), Langer 1980. The parameters involved are depending on the stress level and the temperature. The finite-element-method is applied to rotationally symmetrical three-dimensional problems. The non-linear calculation method is based on an implicit method with respect to time. A modified Newton-Raphson-method and the initial strain approach are employed. Along with some experiences on suitable numerical procedures, examples are shown for the characteristical effects of time-temperature dependency. Having achieved convergency and reliability a method is now available for practical design and parametric sensibility studies.

Jan 1, 1982

By McKee DJ

Future mineral processing developments will be of two types. There will be a continuation of the advances of the last 20 years including major increases in equipment capacities, the development of reliable on-line instrumenta- tion, the use of digital computers for automatic control, and the greatly expanded use of in-situ leaching techniques. However, there will also be a need for innovations as the industry faces a different set of problems to those involved in cost and extraction efficiency considerations. These new problems include those relating to energy usage, environmental pressures, and the further development of large low grade deposits and small, high grade metallurgic- ally complex deposits. Present technology does not appear adequate to solve many of these new demands. New treat- ment concepts will be required, and the immediate outlook in this regard is not encouraging. A major research and development task in mineral processing over the next 20 years will be to seek out new ideas and develop them, and this must be pursued with imagination and determination. Both the continuation of the present research pro- grammes and the development of new methods will require a steady supply of highly qualified technical personnel. These people are not being produced in the numbers required, and this situation must be urgently rectified.

Jan 1, 1981

By John Chipman, Donald W. Murphy

RECENT developments in iron alloys containing nitrogen have indicated that this element may exert a considerable influence on the properties of the metal. This influence is not always in an undesirable direction and the indications are that nitrogen should be regarded as an alloying element, the amount of which should be subject to control, rather than as an inherently deleterious impurity. In controlling this element in liquid iron to the best advantage, it is necessary to have a reliable background of fundamental data pertaining to solubilities, rates of solution and chemical reactions of nitrogen in liquid iron. Obviously, the first step in such an investigation is the determination of the solubility of nitrogen in pure iron, and this has been the object of the experiments described in this paper. The solubility of nitrogen in solid iron has been measured by Zurich,1 Sieverts,2 Martin,3 and Iwasé4 and, the agreement among the first three inspires confidence in their results. No accurate determinations of its solubility in liquid iron have been recorded though several investigators have obtained approximate results. Strauss5 was able to introduce 0.03 to 0.04 per cent nitrogen into steel by the action of either ammonia or nitrogen on the liquid metal. This was accomplished by Eilender and

Jan 1, 1935