Search Documents

By Gregory Witte

This paper will explore the technology behind and applications of smart motor control centers (MCCs) being used today in mineral processing facilities. The two technologies to be discussed are solid-state motor controllers that can be installed in MCCs and the complementary digital communication networks that can transmit operational parameters of the solid-state devices to the supervisory system. The toughness and reliability of solid-state technologies have led to a dramatic increase in their usage throughout the mining industry. Products such as solid-state motor protectors, controllers, and variable frequency drives have demonstrated greater flexibility and performance in a variety of applications than their electromechanical and mechanical counterparts. The three key trends apparent in the solid-state devices are: 1. A shift to smaller, smarter, more integrated devices, which allows a single solid-state device to serve the purpose of multiple electromechanical devices but in a much smaller form factor. 2. Distribution of control logic in motor control devices rather than conveyed through a hard wired connection to a central automation system. 3. Embedded network communication that allows supervisory systems to have an expanded view into critical loads and sensors. In applications, the use of smart actuators and sensors with integral local intelligence and communication allow a supervisory controller to send high level commands and let the smart device coordinate its own work The ability of smart field devices to return noncontrolled, nonpoled information opens a whole array of new capabilities for preventive maintenance and diagnostics and forms the basis for an effective motor management program. The smart motor control devices this paper will explore are the smart motor protectors (SMP), smart motor controllers (SMC), and variable frequency drives (VFD).

Jan 1, 2000

By N. J. Gran, W. R. Opie

HYDROGEN in molten aluminum and aluminum alloys, which precipitates during cooling and solidification, is the principal cause of pin hole porosity in ingots and castings. Much attention has been given to determining the effect of temperature and pressure on the solubility of hydrogen in pure aluminum, but little data are available on hydrogen solubility in aluminum alloys. This investigation was undertaken to check results reported for pure aluminum and to show the effect of silicon and copper additions on the amount of hydrogen contained by molten alloys. Previous determinations of the solubility of hy-drogen in molten pure aluminum are plotted in fig. 1. The most reliable data appear to be those of Ransley and Neufeldl and of Baukloh and Oester-len.' The latter authors also report some results on the effect of copper and silicon additions. Up to 6 pct these elements decrease the solubility of hydrogen quite rapidly, with a definite minimum noted at 6 wt pct for both copper and for silicon, although no reason is apparent for these minima. Experimental Procedure The solubility of dry hydrogen in pure aluminum, aluminum-silicon, and aluminum-copper alloys was determined by the method of Sieverts.8 This consists of determining the volume of the gas system above the molten metal at a given temperature and pressure by using an insoluble gas. This volume is referred to as the "hot volume." The system is then evacuated and the soluble gas is introduced at the same temperature and until the same pressure is reached. It is necessary to introduce enough of the soluble gas to fill the space above the metal plus the soluble amount. The difference in the volume of soluble gas and the "hot volume" is the solubility. The accuracy of solubility measurements by the Sieverts' method is primarily depend-

Jan 1, 1951

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By Walsh V

The Australian economy has been adversely affected by the hesitation in developing countries to commit to the construction of .new coal-fired power stations. World coal trade which was expected to grow at an appreciable rate has stagnated, world export coal prices have plummetted, and facilities in place in Australia for the production and export of coal are being underutilized. While in some countries this hesitation has been caused by a reduction in electricity load growth, another cause has been the unduly long lead-time imposed on developing countries by the conventional "Banker's Approach" to the planning and initiation of commitments to finance and construct coal-fired power plants. In some countries electricity growth has been met by increased usage of indigenous energy resources, even though this involves costs in excess of imported coal-fired power generation. The avoidance of foreign exchange commitments in these cases can however be desirable. In many other developing countries however, fuel oil continues to be used for power generation at a cost in foreign exchange of up to 50% above the total cost of coal fuel plus capital to construct a new coal-fired power station. The conventional "Bankers Approach" to new power station planning imposes the need for successive feasibility studies to satisfy the normal processes of international development lending agencies. No feasibility study can however, show how keen vendor countries may be to win major power plant contracts; and no feasibility study can determine whether the power station eventually procured will be one of the more reliable, at better than 80% availability, or one of the more unreliable at worse than 60% Availability.

Jan 1, 1987

By Jin Zigang

In China there are more than 30 coal fields menaced by karst-confined water. In the north and east of China there are many collieries which mine coal seams of the Carboniferous and Permian Systems, which are above the Ordovician limestone (general thickness is 500-600 meters). Ordovician limestone is full of karst fissures, contains a lot of water under high pressure (15-65 kg/cm2) near the commercial coal seams (20-80 meters), the water easily infiltrates the thin lime- stone at the point of the structure crevice, so water-irruptions from the floor are the main source of water-related disasters in these coal fields. According to the statistics there were more than 300 accidents of all kinds of water-irruptions from the floor in these fields since the beginning of their development. It is of great significance in developing coal production in the eastern part of China to solve the problem of safe mining of the seams menaced by the karst-confined water of the Ordovician limestone. The research on this subject consists of three parts: (1) investigating the geological structure and hydrogeological conditions of each mine of the mining area; (2) researching the mechanism of water-irruptions from the floor and proposing reliable methods to predict and monitor; (3) improving the mining system and proposing a mining plan with safety precautions against water-caused accidents. The chief task is to research the mechanisms involved and to discover the causes and conditions of the phenomenon. The authors have obtained some findings on this subject in the last five years, making use of the comprehensive observation and research system, which will be discussed under three headings.

Jan 1, 1984

By Anshumali Gangwar

This paper outlines the chance constrained binary integer program developed by the author in his doctoral dissertation at Columbia University, New York, 1973. The optimum planning of a mining program involves the determination of a production schedule which maximizes the net present value of the mining property. The actual mining process has an inherent stochastic and discrete nature. In particular, the demand for the mined product and the grade of the mineralized material in the ore are the two most important stochastic mining variables. The decision to mine or not to mine any block of a mining property is a binary integer variable. This paper outlines the formulation of pit production scheduling problem as a chance constrained binary integer program. The deterministic equivalents of these chance constraints are nonlinear in binary variables which have subsequently been linearized. The planned objective is to meet with a stipulated high degree of reliability, all the random demands as they materialize with a random supply of the commodity being marketed as determined by the eventuating random grade values of the exposed ore blocks and the mining system's production constraints such that the discounted total production costs over the entire planning horizon are minimized or the profits maximized. The emerging surface of the mine in each scheduling period is determined by the values taken by the binary decision variable associated with each block of material in each scheduling period.

Jan 1, 1982

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

By H. C. Fowler

No exact demarcation can be made between producfion engineering and engineering research projects which interest production engineers because the results of today's engineering research make possible many of the applied production engineering methods of tomorrow. A corollary of the development of fundamental research is that so-called practical research becomes necessary. Assuming engineering research to include all subjects related to oil and gas production on which knowledge is being increased through experimentation and through analyses of data obtained from both the laboratory and the field, a review of the work of 1932 shows that the fundamental concepts of at least three major problems have become better understood—bottom-hole pressures, solubility of gas in oil, and fluid movement—and that the established data on the relationships of oil and gas have been applied to obtain more efficient and more economic production of both. Engineers no longer are concerned primarily with the initial development of devices for obtaining the pressures at the bottom of wells. Advancement in the technique of obtaining reliable pressure readings in wells has been rapid. One of the first public suggestions regarding apparatus for obtaining precise information at the bottom of oil wells was made before the Petroleum Division of the A.I.M.E. in 1928. Even during the early development stages in East Texas, reservoir pressures were estimated from well-head observations. Soon, however, a number of proved devices and methods were available, and today bottom-hole pressures in many fields are being recorded and studied as an essential part of the production programs. The research now turns to interpretations of data, obtained with these devices, in terms of reservoir energy and to the development of methods whereby the oil and gas will be withdrawn in accordance with rational and equitable programs based on oil-gas-energy relationships. The term ((bottom-hole pressures" should not be interpreted as indicating the full scope of all research on this problem. By using pressure (and temperature) data obtained in related vertical-flow studies,

Jan 1, 1933

Provide coal mine shafts/slopes with an optimum coal mine shaft fire and smoke protection system composed of reasonably-priced, reliable hardware. Approach Accident and injury data indicate that a relatively low percentage (5%) of underground coal mine fires occur in shafts or slopes. Nevertheless, shaft or slope fires are extremely serious because they block critical escape routes for miners. That also can happen when combustion products resulting from fires in other mine areas contaminate shahs and slopes. Seeking the optimum configuration for a shaft/slope fire and smoke protection systems, the Bureau of Mines gathered data on the performance of existing fire detection devices and signal telemetry systems In several mines, and analyzed the generic protection needs of the U.S. underground coal mining industry. The optimum system developed by the Bureau provided an adequate number of detectors, a wide area of coverage, and an extensive data acquisition, analysis, display, and storage capability. This system. recommended for fabrication and in-mine testing, consisted of a microcomputer-controlled master panel located in the test mine's slope hoist room, and four remote units. Two of the remote units were placed on the surface atop upcast ventilation shafts, a third was situated underground near the slope bottom, and a fourth was installed at the slope top in intake air.

Jan 1, 1986

Caving is the lowest cost underground mining method, provided that drawpoint spacing, drawpoint size and ore handling facilities are designed to suit the caved material and that the drawpoint horizon can be maintained for the draw life. In the near future several open pit mines that produce in excess of 50 000 tons per day will have to examine the feasibility of converting to low cost, large scale underground operations. Several other large scale, low grade underground operations will experience major changes in their mining environments as large dropdowns are implemented. These changes demand a more realistic approach to mine planning than has occurred in the past, where existing operations have been projected to increased depths with little consideration of the change in mining environment that will occur. As economics force the consideration of underground mining of large, competent orebodies by low cost methods, the role of cave mining will have to be defined. In the past caving has generally been considered for rock masses that cave and fragment readily. The ability to define cavability and fragmentation, the availability of large, robust LHDs, a better understanding of draw control requirements, improved drilling equipment for secondary blasting and reliable cost data have shown that competent orebodies with coarse fragmentation can be exploited by cave mining at a much lower cost than with drill and blast Methods.

Jan 1, 1995

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Harry J. Olson

Geothermal Energy has a great potential for meeting the electrical and thermal energy requirements of many countries and territories lying along tectonically active zones within and surrounding the Pacific Basin. Energy requirements for many of these small, scattered volcanic island nations preclude development of conventional generating facilities large enough to incorporate any economies of scale. However, by attempting to discover and develop shallow, relatively low temperature, geothermal reservoirs associated with recent vulcanism on many of the volcanic islands, exploration expenditures and risks, and problems associated with the development of high temperature resources can be reduced. Exploration and development drilling for these resources can be accomplished with truck mounted rotary drilling rigs that are less costly and more suitable for operations within the island infrastructures than the conventional rigs normally used in the drilling of deep, high temperature geothermal resources. Experience over the past decade with small, modular, binary (Rankine) cycle generating units indicates that geothermal energy can provide a reliable source of baseload electricity in the amounts required and at a cost that is competitive with other alternative and conventional energy sources. Development of shall, moderate temperature, geothermal resources with small, modular binary cycle generating units can provide ideal additions to the energy sources of many of the Pacific volcanic island nations within the framework of their island economies.

Jan 1, 1991

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By Poplawski R. F

A 32-channel PSS seismic monitoring system was commissioned at Mt Charlotte mine in 1994, and at the time it was the first such system in Australian mines. The system continuously observes the occurrence of seismic events and locates them accurately in space and time. Mt Charlotte has a history of seismicity, with the largest event in recent years of Richter magnitude 4.3. The decision to 'go seismic' was made despite some uncertainty regarding its potential usefulness. However after the first year of operation, benefits have been realised in terms of less production downtime, improved mine safety and mine planning, and better understanding of the nature of Mt Charlotte seismicity. The seismic network has performed well, recording 550 events in its first year of operation to a location accuracy averaging ¦ 12 metres. System reliability is excellent, with very little downtime, and acceptable operation and maintenance times and costs. Observations show major distinct changes in the rate of mining induced seismicity over time periods of weeks and months. Events have tended to cluster in specific mine areas and on particular faults and structures. Case examples of pillar preconditioning, breakout around an orepass, and a major stope rockburst, illustrate the role of seismic data and the benefits it brings to safety, productivity and planning.

Jan 1, 1995

By Faruk Oksuz, Cary Hirner, Ray Brainard

"Key project participants, including owners, engineers, and contractors continually seek for sound and structured decision analysis on how to select the best contracting method for successful project delivery. In addition to being burdened with technical challenges, lack of resources, budget shortcomings, regulatory requirements, and bureaucratic and politically mandated obstacles, the project participants need a reliable decision analysis model on the best project delivery method. The pendulum of choice for contracting continually swings back and forth between traditional design-bid-build and alternative delivery options such as design-build, progressive design-build, construction manager at risk, and public-private-partnership. For large tunnel projects, the decision process is further complicated due to contract packaging options as well as risks in underground construction. Contracting strategies for large tunnels require thorough consideration of performance, risk, quality, operability, cost and schedule. This paper compiles an array of decision making criteria and tools for an unbiased and balanced evaluation and ranking system in the procurement of large tunneling projects. INTRODUCTION Successful project delivery hinges upon meeting the owners’ expectations and key performance indicators. Large tunneling programs benefit from a thorough understanding and successful implementation of project delivery options by key project participants including the owners, engineers and contractors. The key to success is a collaborative advancement of project as the key project participants knowledgably address the applicable management, performance, risk, quality, cost, operability and schedule considerations throughout a project realization cycle. PROJECT REALIZATION CYCLE All projects have customary planning, design, construction, commissioning and operation phases that may seem to be sequential but in reality that are well integrated and dependent on one another. A glitch in any phase of a project realization cycle could hinder a successful outcome and none of the project partners are immune to consequences whenever and wherever they may surface."

Jan 1, 2016

By L. A. Cornish, R. Süss, M. Sephton, N. B. Maledi, J. H. Potgieter, L. Chown

The gas turbine industry is faced with a challenge to improve the performance of engines, while simultaneously adhering to stringent environmental legislation. One way of addressing the problem is by further increasing the recipient working temperatures. Unfortunately, the use of nickel based superalloys (NBSAs) in the gas turbine industry has reached its limitations. Although coatings can be used for small increases, and air cooling is also incorporated by design, attention is towards developing stronger metallurgical materials having higher melting points, with acceptable creep and corrosion resistance. A series of ternary and quaternary Platinum-based superalloys were developed. Platinum was selected because of its higher melting points compared to nickel, similar fcc structure and better corrosion properties. Mechanical characterisation studies of Platinum-based superalloys alloys, which included oxidation, creep and hardness, demonstrated reasonable results, outperforming an oxide dispersed strengthening (ODS) Fe-based superalloy (PM2000) and a nickel based superalloy (MAR-M200). During any materials development where high temperatures are concerned, high strength is the primary property of interest. However, during the development of gas turbines, component life and reliability, which are influenced by temperature, need to be taken into consideration, and therefore creep as well as corrosion (both temperature dependant properties), are important. These properties become significant with increasing temperatures. With increasing demand for higher temperatures, it is becoming increasingly important to include hot corrosion properties of the alloy during the material selection process. A short description on hot corrosion and its degradation mechanisms are given in this paper. Coatings are currently dominating as the best practical solution to address temperature increases. This paper looks at benefits and shortcomings of coatings over Pt-based superalloys as candidates for applications under extreme conditions. Key words: Hot corrosion, Pt-based superalloys, Ni-based superalloys, Coatings

Jan 1, 2006

By Burt Hartmann

The nation's ever-expanding construction and mining activity has placed an increasing demand upon engineers and geologists to design and construct stable slopes in earth materials-soil and rock. Man's attempt to handle these slope stability problems has been based primarily on practical experience and the resulting theories formulated to explain the phenomena. Too many instances occur when man is faced with a slope stability problem that has not yet been experienced and doesn't lend itself to solution by any existing theory. At this point he must extend himself in using his engineering judgment to arrive at a reasonable and safe design. As past experience has shown, all of the "safe designs" are not really safe. Sometimes they result in embarrassing failures. Measurements provide the key to understanding and controlling natural phenomena. We cannot hope to gain control of the slope stability problem until we understand the causes of slope failure, their behavior with respect to time and their relative magnitudes. Measurements required for an adequate definition of any slope problem must be of the highest reliability because of the importance of decisions which must be based on them. For this reason, direct measurements of movement, shear strength, water pressure, etc. of the unstable mass are preferable to indirect measurements of other physical properties. Movement instruments which can be positioned inside of the slope mass (within boreholes) are among the most useful in diagnosis and/or monitoring of slope movements. The higher the sensitivity and il-measurement precision possible with borehole instruments, the quicker the required information can be obtained and the more exactly may hazardous conditions be observed. A high density of measuring points in a single drill hole is deemed essential for diagnostic purposes. Behavior gradients may thus be obtained. The Pressure Meter (Fig. 1) can be used to measure a relative strength

Jan 1, 1968

By Frank W. Bowdish

During the early 1960's, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By J. F. Archibald

It is often alleged by mine ventilation engineers that no reliable method exists to forecast the levels of radiation to be encountered in future uranium mines. It results that the design of uranium mine ventilation systems is based on factors other than radiological hazards, such as radon and radon daughter concentrations, for which permissible limits are set. Ventilation has been used to date as the main control mechanism for radon and radon daughters. Although it has become increasingly difficult to provide enough ventilating air to reduce the radon gas and its daughter products to safe levels in some mining arrangements, it is not the object of this paper to discuss alternatives to ventilation. This paper will describe a methodology followed by the authors over the years to estimate the levels of radiation to be encountered in underground and open pit uranium mines. Ventilating air is used to maintain working level concentrations within safe limits. The sources of radon and radon daughters and the quantities of each which will be produced, will be of great value in planning and designing a ventilation system to control them. This information can afterwards be integrated into the overall mine design. The methodology to be outlined can also be used to estimate, given a mine design format, the radiation levels to be encountered. If levels are not acceptable, modifications in the mine design can be made at an early stage. The emphasis is placed on an integrated effort where the ventilation engineers and the mine design engineers work in close collaboration from the very start of the mining project. Estimation of radon and radon daughter levels can be initiated as soon as core samples are obtained from the exploration programmes.

Jan 1, 1980