Search Documents

By Nora M. Hutt, Kevin A. Morin

Geochemical static tests are a basic component of geochemical assessments and predictions for acidic drainage, and include acid-base accounting and total-metal contents. A key database for such information is the International Static Database (ISD), which currently contains more than 45,000 static-test analyses from over 200 minesites. Such large databases are useful in identifying general trends and, just as important, the percentage of exceptions. General trends and significant exceptions can be seen in the ISD by comparing one parameter against another. This paper shows that bulk neutralization potential (bulk NP) obtained from acid titration is often a good indicator of neutralizing capacity above values of 10 t CaCO3/1000 t. Other types of calculated neutralizing capacity are then compared to bulk NP to determine if they, in fact, reliably represent actual neutralizing capacity and if they can substitute for the more time-consuming and expensive bulk NP. For example, bulk NP correlates better with Carbonate NP (from carbonate analyses) and Total-carbon NP (from total-carbon analyses) than with (Ca+Mg) CaNP (from solid-phase analyses of calcium and magnesium). This means that, in general, (Ca+Mg) CaNP is a less accurate substitute for bulk NP than the other types, and thus requires intensive site-specific justification if a substitution is attempted. This also means that measurement of the frequently less-expensive parameters of total carbon and carbonate can often substitute, within site-specific error bars, for the bulk-NP titration. However, the ISD also shows that non-carbonate minerals make the primary contribution to neutralization in up to 20% of samples, so Carbonate CaNP and Total-carbon CaNP do not always reveal the full neutralizing capacity of a sample.

Jan 1, 2000

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

This report describes the redesign, development and field demonstration of a remote shotcrete lining system, capable of operating in shafts and mines from 8 to 16 feet in diameter at depths up to 1000 feet. The original contractural scope of work outlining problems and remedial measures associated with a previous unit proved inadequate. Significant additional effort was necessary in order to fulfill the project objectives of producing a functionally reliable remote shotcrete lining system. Included with the engineering and technical description of the system, is a comprehensive technology package. Included with this material is ancillary equipment, materials selection procedures, mix-design data, quality control and assurance program, selection and training of personnel and the organizational aspects required to operate the entire system. The report concludes with details of a successfully completed borehole lining operation at the Nevada Test Site. An irregular 104 inch diameter borehole was lined at a rate of 4.8 feet per hour and 20 feet per hour respectively for 8-9 inch and a 2 to 3 inch shotcrete thickness.

Jan 1, 1983

By E. Hornbogen, R. C. Glenn

Copper precipitates from a iron as fcc E phase without formation of intermediate compounds. In the first stage of the precipitation, spherical particles with diameters < 100A are formed at a high rate. During the second stage, the particles grow at a rate given by Zener&apos;s equation for growth of a spherical precipitate. In the third stage, growth is slower. Rod-shaped particles form after long aging times at 700°C. Maximum strengthenzng was observed at the beginning of the second step of precipitation. During plastic deformation of the aggregate, particles appear to deform initially by twinning. THE work discussed herein was part of a study of precipitation of substitutional elements from a iron. Copper was chosen as one of these substitutional elements because it has about the same atomic size as a iron, and does not form an intermetallic compound with iron. The data on the iron-copper system then available were summarized by Daniloff1 several years ago. The solubility of copper in a iron has been determined by electrical conductivity measurements,2 lattice parameter measurements,3 and by saturating thin iron foils with copper and determining the copper content.4 The results of the three investigations do not agree very well, but the value of 2.4 wt pct for the maximum solubility at 840°C seems to be the most reliable,4 Fig. 1. An alloy containing 1.23 wt pct Cu was used in our work to assure starting with a completely homogeneous material. On the copper-rich side of the diagram, there is a maximum solubility of about 4 wt pct Fe in copper at 1094°C ( phase). The precipitation of

Jan 1, 1961

By Cristián Araya L.

A dynamic agglomeration, heap leaching, solvent extraction and electrowinning software, called NICO, has been developed in order to either design or simulate copper ore recovery plants. NICO contains a library of routines, each representing a unit operation or piece of equipment, which are assembled like a meccano to match almost any wet plant configuration. Routines include agglomeration or curing either in drums or belts, belt conveyors, heap stacking and reclaiming, heap leaching of oxide, sulfide or mixed copper ores, heap irrigation, drainage, ponds, mixer-settlers, filters, columns, coalescers, tanks, electrowinning cells, pumps, and all connections and related piping. All models are semi- phenomenological, i.e., they include all physical-chemical, mass, thermal, transport equations, which are required to represent as closely as possible the equipment or unit operation. However, operating experience has been incorporated into the model in order to make it simpler, faster and reliable. This experience has been tested in several plants in Chile since 1992. Site meteorological data is simulated also; in this way the model is responsive to weather conditions (temperature, solar radiation, ambient humidity, atmospheric pressure, wind velocity, etc). NICO has been used recently for design and optimization studies in copper plants in Chile like Radomiro Tomic, Collahuasi and Zaldivar. A user-friendly interface allows fast and comprehensive simulations. The entire plant is shown in a single graphic screen, so the user can see all the relevant information, and soft-keys are provided in order to change parameters on-line and watch their effect in final copper production in cathodes. Model also calculates and reports operating parameters, as well as estimated investments and operating costs.

Jan 1, 1999

By T. Smales, P. L. Wright, K. Barron

The results of field measurements using an air injection technique to investigate the integrity of three pillars in the Mclntyre Mines Ltd. 114 seam at Crande Cache, Alberta, are reported. These pillars are shown to be stable and an estimate is made of the strength of these pillars. Using these results, together with Hustrulid&apos;s pillar strength formulae, a general pillar strength equation for the 114 seam is developed. This equation takes into account the probability of failure that may be deemed tolerable within the design requirements. The variation of the minimum pillar dimensions with depth below surface for uniform pillar layouts is then examined for a range of tolerable failure probabilities. A general equation of the form B = 2.60 +B Z relates the minimum pillar design width, B metres, with the overburden depth, Z metres, where B is a parameter related to the tolerable failure probability. This equation only applies for 3.05m high pillars with 6.lm wide entries. Finally, the question of what failure probability is tolerable within the design of mine pillars is discussed. This will depend on the support role required of that pillar and the anticipated period over which the pillar must perform that role. Five categories of coal mine pillars are defined, each with a somewhat different role to perform. Tentative design criteria in the form of "tolerable probabilities of failure" are suggested for four of these five categories of pillar. The fifth category of pillar has no reliable support function to perform and support must be obtained by other means.

Jan 1, 1983

By Bhattacharyya AK

With increasing demand for more efficient production from the underground coal mines in the Southern Coalfields- of New South Wales, their design and operational aspects are constantly being reviewed and improved. One key area in such pursuits is the reliable design of stable and yielding pillars. The current designs of pillars based mostly on experience leads to unnecessary sterilisation of coal or strata control problems. To explore such mine design problems, computer based modelling is increasingly being applied. In the study described in this paper, the object was to determine the particular width of pillars separating three roadways in a panel at which the pillars yielded completely and their loads largely transferred to the unmined coal at the flanks of the panel. This was approached through a computer simulation of the behaviour of the strata around a panel, in which the three roadways were separated by pillars of progressively decreasing width. A computer program called FLAC based on the finite difference method was used to simulate the relevant strata behaviour in vertical sections. The appropriate in situ values of the deformability parameters relating to the coal seam, roof and floor were determined from the back analysis of some displacement measurements in such a panel. The process involved successive modelling of a vertical section through such a panel,starting with realistic values of the parameters and varying them until the measured and the modelled displacements agreed closely. Based on the results of the numerical modelling, the width of a yielding pillar for the given conditions is Suggested.

Jan 1, 1992

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By Falconer A. J

Two magnetic parameters are proposed as a basis for the assessment of ironsands beneficiation. The parameters are deter- mined for raw sand prior to dredging and for magnetic separator head feed over a production period of five months. The relationships between these parameters and the performance of the magnetic separators are examined to establish the value of magnetic assessment compared with the traditional soluble iron assay method. The results illustrate that the first parameter, true magnetic fraction (TMF), has a value superior to that of soluble iron when relating raw sand grade calculated by tri- angulation to magnet performance. In terms of the relationship between magnet head feed grade and magnet performance, TMF and soluble iron perform equally as assessment parameters. For the ironsands mined during the five month period, the second magnetic assessment parameter, composite fraction (CR), is shown to merely reflect TMF and offers no additional information for assess- Ment. Conclusions are that true magnetic fraction has many advantages over soluble iron in terms of time and cost of determination and that it is a meaningful and reliable parameter upon which to base all calculations relating to the mining and beneficiation of ironsands.

Jan 1, 1980

The paper first outlines the conceptual basis for evaluating and controlling geological risk. Geological risk, the economic reflection of the uncertainties associated with tonnage, grade, and other pertinent deposit parameters, is evaluated in terms of economic risk criteria. Delineation provides the deposit information required to appraise and control this risk. The improved reliability of geological estimates resulting from additional delineation reduces the economic risk associated with mine development and production decisions. However, the benefits of delineation, subject to diminishing returns, have to be weighed up against the direct and time costs involved. These costs decrease base case economic values and shift the probability distributions of possible outcomes towards, lower values. The optimum amount of delineation normally is achieved short of the point where economic risk is minimised, depending on the mining company&apos;s relative preference for a higher base case value or a lower economic risk. Then, two open pit copper mine examples, based on actual situations, are analysed to illustrate the application of the concepts presented. The first case concerns the extension of ore reserves at an operating mine. Finally, a new mine development opportunity is considered.

Jan 1, 1994

By T. A. Gray, L. M. Crayne, P. Glogowski, Trevits. M. A.

Of the 19 major mine fire events (including thermal events) that have occurred in the last 6 years (2000-2005), it is estimated that remotely constructed mine seals could have been used at 65% of the events to control or suppress the fire. Underground observations of seals that have been remotely installed during mine fire events show that they often do not fully achieve mine roof-to-floor and rib-to-rib closure. Unfortunately, the inability to reliably close the mine void has limited or precluded the regular use of this technology. The National Institute for Occupational Safety and Health is conducting full-scale underground experiments at the Lake Lynn Experimental Mine to identify and remedy existing remote sealing technology shortcomings, to develop novel technologies, and to transfer the new or improved technologies to the mining industry. This paper will discuss the remote mine seal testing program and will provide the results of the in-mine experiments. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

By David Roha, Øyvind Mikkelsen

"Significant resources have been spent throughout the years in the investigation of production of aluminum by carbothermic reduction. Due to the technological challenges involved, the efforts have not yet resulted in a commercial process. An initiative to overcome issues that prevented previous attempts to succeed was taken by Alcoa through the Advanced Reactor Process. The research program has resulted in technical developments which have resolved many of the previous issues. The knowledge about the process has continuously improved through physical and computer modeling as well as by experimentation at various scales. The technical achievements together with improved process understanding have resulted in a reactor design able to continuously operate the process for several weeks at the time, with hundreds of kilograms of alloy in every tap.IntroductionThe Hall-Heroult process has since its invention in the late 19th century, been essentially the only process used for commercial production of primary aluminum. The process has so far proved to be superior to all potential process alternatives and has continuously been improved. Although the Hall-Heroult is a reliable process it also has challenges:"

Jan 1, 2012

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60&apos;s and early 70&apos;s efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70&apos;s. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By T. W. Guy

THE increased moisture due to water¬spraying for coal dust control is of interest even for mines from which the coal is to be wet-washed before screening, because in many cases wet coal dust materially decreases the loading efficiency of men an equipment at the faces. It also causes serious increase in the normal wear and deterioration of all equipment with which it comes in contact. It is important to the consumer if it increases his as-receive moisture. No attempt will be made in this paper t cover the entire subject of water-spraying of coal for dust control. It will be confine to discussion and data on (r) percentages c dust in bituminous coals, (2) moisture increases due to spraying for dust control in mines or plants by methods which have proven satisfactory for periods of one to five or more years, and (3) a few suggestions for research. SIZE AND PERCENTAGE OF COAL DUST The U. S. Bureau of Mines1 classifies a coal dust all bituminous coal passing 20-mesh sieve (0.0328 in. square opening; The percentage of such dust to be found is ROM coal, of course, varies widely wit. the characteristics of the seam, and with the methods used in the mining and in the preparation of the coal. ROM screen analyses of 12 U. S. coals selected at random from personal files given in Table I show: A few other screen analyses examined indicating 40 pct or more of 2o-mesh X o dust in 3/8 in. X o-sizes were not included because of uncertainty that they were representative. The number of results in Table I is not sufficient to give a reliable estimate of the average, or of the range to be expected, but it indicates that in every case the coal dust is a relatively large percentage of the total ROM coal, and, of course, a progressively larger percentage of resultants as the larger sizes are separated for marketing.

Jan 1, 1948

By E Widzyk-Capehart

The conventional ammonium nitrate fuel oil (ANFO) loader utilises a pneumatic system to control the flow of ANFO (via rotary actuator/ball valve) and air (via an auxiliary air valve). This system, though relatively simple and reliable, has several drawbacks with respect to ease of control and level of automation. In this paper, a radio frequency (RF) remote control for explosives charging is discussed. The system design incorporates electric solenoid valves to control the rotary actuator and the auxiliary air valve. All operations associated with explosives charging are selectable at the remote and are completed according to a modifiable time sequence. This allows the following charging sequence to be reduced to a single momentary application of the remote:removal of water from the hole prior to charging with ANFO; charging of the hole for a preset but adjustable period of time; and removal of the remaining ANFO from the ANFO hose. A specially developed remote switch allows the operator to maintain two-handed control of the ANFO hose whilst achieving full control of the charge-up process. Failsafe electronic architecture is incorporated into the systemÆs design to increase safety to the highest level. Should the RF remote control fail, a wired remote is included in the system to allow for the charging process to continue, albeit at a reduced level of control. The application of the RF remote control system in an underground explosives charging operation minimises and/or eliminates many problems associated with the use of the conventional charging system. These include: the wet-hole problem, trip and entanglement hazards, air embolism and the two-man loader control requirement. The developed remote control unit proved to be effective at removing water from wet holes leading to increased face advance per drilling operation. It proved to be economically feasible, allowed for an increase in systemÆs dependability and safety factor and for a truly one-man operation which resulted in reduced manpower.

Jan 1, 1999

By Milton Lissberger

MILTON L. LISSBERGER, ? New York, N. Y.-Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, remelted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 12, 1918

The earth is a planet limited in size and limited in total resources. For the forseeable future, it is the only available habitat for mankind. Therefore, it follows that the more we know about our planet the better we can utilize its space and its resources for our well-being now and in the future. But, to accomplish this, we need reliable basic information. Geosciences provide such information. Recently, Dr. M. King Hubbert took note of the important effect of the geosciences on society, on how we think, and how we live. In the first century of modern geology, 1780- 1880, the influence of geology was primarily on how we think, i.e. changing our concept of the earth from one with a short catastrophic history to one that developed gradually over enormous spans of time. In the second century, 1880-1980, the emphasis was on how we live, on expanding the knowledge base so that we could more easily find and utilize the earth&apos;s resources. Now, in the third century, i.e. from 1980 towards the year 2000 and beyond, we should concentrate on both how we think and how we live; i.e. how we can better estimate potential global&apos; resources and how we can manage these resources for maximum benefit to mankind. Like other sciences, the geosciences build upon what has already been done. Progress is achieved by using the thoughts, measurements, and observations of past workers, adding to these the insights from new experiments and from new concepts. Geology has its own methodology and approaches; but more than most sciences, it calls also upon the tools of physics, chemistry, mathematics, engineering, and biology to help solve its problems. Today&apos;s increasing population, increasing industrialization, and increasing complexity of modern society demand more detailed geoscience information so as to better use the land, reduce geological hazards, provide an inventory of resources, facilitate waste disposal, and prepare for long-term effects such as changes in climate and sea level.

Jan 1, 1986

By Wilhelm in der Schmitten

A necessary condition for a uniaxial stress distribution in compression testing is that the specimen end surfaces make full contact with the apparatus compression plates. In addition all compression surfaces must be machined perpendicularly to the loading axis. In general this condition is not sufficiently fulfilled in a simple apparatus. Therefore on application of the load the compression plate may first touch the specimen at one point only. This may cause crumbling of the specimen if the material under investigation is brittle (e.g., ionic crystals). It also precludes a precise study of the beginning of deformation as the effective cross sectional area is unknown. In addition a complex stress state is set up which renders quantitative work impossible, e.g., on dislocation density and arrangement as a function of stress. To overcome these difficulties a "self-adjusting" upper compression plate is required. A simple and reliable method of achieving this is shown in Fig. 1: A steel hemisphere is placed on the specimen. As soon as the compression plate (which no longer needs precise machining) makes contact with this hemisphere the load is uniformly distributed over the whole specimen surface, and a homogeneous uniaxial state of stress results. An advantage of the method is that the loading is always central, even when the specimen surface is not parallel to the compression plate (Fig. 1, dashed line). Therefore to a first approximation a uniaxial state of stress is maintained if the misorientation of the specimen end surface is small. Two typical stress strain curves of identically prepared sodium chloride crystals are shown in Fig. 2; curve 1 was taken without and curve II with the hemisphere under otherwise identical conditions. The improvement in the accuracy of defining the beginning of elastic and plastic deformation is clearly indicated. The writer wishes to thank the Deutsche Forschungsgemeinschaft for financial support, and Professor P. Haasen for providing facilities for this work.

Jan 1, 1962

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968