Search Documents

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By Robert L. Virta

An asbestos substitute is any material that replaces asbestos in a commercial product. There are many asbestos substitutes, each with its own unique physical and chemical properties. Substitutes can be inorganic or organic, fibrous or nonfibrous, and natural or synthetic. They also can be used as a direct substitute for asbestos or as a replacement product. Probably in no other field is the diversity of substitute materials so great. The concept of asbestos substitutes is not new. The first major effort to develop asbestos substitutes was undertaken by the federal government. The United States has always been dependent on foreign sources for strategic-grade asbestos, and during World War II, the government was concerned that these supplies would be cut off. Strategic-grade asbestos was critical in many electrical and thermal insulation applications (electrical insulation, battery plate separators, flame-proof boards, insulation for rocket components, etc.). A reliable supply of nonstrategic-grade asbestos also was required for general civilian and military applications, such as in brakes, clutches, and construction materials. The government not only initiated a major search for deposits containing strategic-grade asbestos, it also funded research on synthesizing asbestos in the laboratory and developing products that did not contain strategic- grade asbestos. These efforts, as well as those conducted by the private sector, generally were unsuccessful. In the late 1960s and early 1970s, a second major effort to develop asbestos substitutes began because the general public was concerned about the health threat posed by the release of asbestos fibers during the manufacture, use, repair, and disposal of asbestos-containing products. Strict regulations covering the mining and manufacturing sector already had been enacted because of the issue of occupational exposure. The issue then became environmental exposures. Environmental regulations were enacted, and through time they became more strict. The combination of increasingly strict environmental regulation, maturing of some asbestos markets, and liability issues prompted many manufacturers to discontinue asbestos product lines or search for asbestos substitutes. As a result, asbestos usage dramatically declined from the 1970s to the present (Table 1).

Jan 1, 1994

By J Watson

Electronic detonator technology has been under development for the last two decades. Currently, there are a number of systems commercially available with several others still under development, each with its own unique features. This technology can offer a significant advantage to the drill and blast engineer through their ability to initiate an explosive charge at the æplannedÆ time. This new technology has created huge interest within the drill and blast community and also raised their expectations to produce better blasting outcomes. In many cases, specifications (or even expectations) of desired blast results are not properly defined. Interaction between the input variables (rock mass characteristics and blast design) and results (fragmentation, throw, damage, ground vibrations, etc) and their mechanisms, or relationship to one another, are not very well defined or understood. That is why rock blasting is still considered by many as an art rather than science. With one of the few remaining variables (cap scatter) now controllable, todayÆs blaster finally has the ability to apply science to his trade. Even though electronic detonators are available and becoming more commonly used, current field practices are not always conducive to extracting or deriving the maximum benefit from this new technology. In the authorÆs opinion, the following need to be understood to derive and sustain the maximum value: clear definition or specification(s) of desired outcomes from a given blast; impact of different features in an electronic detonator system (precision, accuracy, flexibility, reliability, etc) and their impact on the desired blasting outcomes; interaction of blast design variables (energy, energy distribution, timing, blast geometry) and their impact on desired outcomes; impact of rock mass variability and quality of blast implementation on the desired blasting outcomes; and critical need to utlilise appropriate tools and systems in order to measure and quantify benefits.In the authorÆs opinion a scientific implementation process is the key to derive the benefits. This paper analyses the industryÆs preparedness to derive the benefits from this technology and proposes a scientific methodology to understand, evaluate and sustain the value from this technology.

Jan 1, 2004

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Yap Chu-Phay

Although chronologically the Sb-Bi system was the first one studied by the writer, the theoretical basis of the equations used in this paper is fully discussed in the writer's paper on the iron-carbon system,' because he believed that many would be more interested in the iron-carbon alloys. He suggests, therefore, that the reader consult that paper to familiarize himself with the theoretical aspect of the thermodynamic treatment outlined herein. This paper is divided into two parts: Part 'I deals with the Sb-Bi system and Part II deals with the lead-rich side of the Sb-Pb system. Although the former system has not much practical interest now, it has great theoretical interest in that it is the one system that for a long time was thought to have (and under specific conditions still has) an anomalous solidus, which no amount of physical investigation could adequately account for. The latter system, of course, is particularly interesting in the lead-rich end. It will be shown that the thermodynamic method is capable of predicting reliably the equilibrium position of the solidus, and thus acts as a check on the experimentally derived solidus. PART I.—THE ANTIMONY-BISMUTII SYSTEM In connection with his studies in thermoelectric phenomena,-the writer was naturally interested in the system Sb-Bi. In consulting the International Critical Tables2 he found the constitutional diagram shown in Fig. 1 (not including Ôtani's solidus), essentially after Cook,³ who investigated the system carefully by thermal analysis. Note the isothermal crystallization of alloys varying in composition from about 48 per cent, (by weight) to pure Bi. This is anomalous, because, according to the phase rule, in a binary system when only two phases coexist, there is univariant equilibrium; that is, the composition changes with the tempera-

Jan 1, 1931

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By A. R. Kaufman, P. Gordon, C. H. Schramm

AS a part of the general program on alloys of uranium carried out at the Massachusetts Institute of Technology under contract W-7405-eng-175 for the Manhattan Project during the recent war, it was considered desirable to investigate the boundary binary phase diagrams of the ternary alloy system uranium-tungsten-tantalum. Previous work on these alloys was practically nonexistent. A brief statement to the effect that tantalum and tungsten form a continuous series of solid solutions was found in a general paper on tantalum by W. V. Bolton1 but no information was available on the uranium-tungsten and uranium-tantalum systems. The research to be described in this paper has served to delineate the main features of the uranium-tungsten, uranium-tantalum phase diagrams and to check Bolton's work on the tungsten-tantalum diagram. Experimental Details Metals: The tungsten and tantalum used for preparing the alloys were 99.96 and 99.65 pct pure, respectively. The chief impurities in the metals were about 0.02 pct molybdenum in the tungsten, and 0.2 pct columbium, 0.05 pct tungsten, 0.02 pct barium and 0.01 pct silicon in the tantalum. The uranium used was 99.9 pct pure, with the main contaminants being iron and carbon. (An appreciable amount of magnesium was present in the uranium as received, but this distilled off during melting and so is not reported as an impurity.) The composition of specimens indicated in the subsequent figures and tables of this paper are the results of chemical analyses on the cast alloys except for the tantalum-tungsten alloys. For the latter, chemical analysis was not very reliable as a result of the difficulty of separating tungsten and tantalum chemically. Consequently, the nominal

Jan 1, 1951

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

The price of oil and other minerals may not make the costly business of offshore exploration seem -attractive at present. There is little doubt that the future search for the strategic resources will tend towards deeper waters particularly on the continental slope margins. In addition with the realisation that active tectonic environments (eg the Makassar Straits) cannot be excluded as potential hydrocarbon sources there is an increasing demand by the explorationists for deep water survey capability. Such deep water research has until recently been restricted to a few specialised academic institutions ;however with the anticipated extra, demand from other institutions, companies, and government agencies, Marconi Underwater Systems Limited (MUSL)and the Institute of Oceanographic Sciences in the UK have come together to allow MUSL to provide the deep water mapping system GLORIA on a commercial basis -for the first time. The GLORIA package comprises a deep water(more than 400m) side scan sonar system which, by operating at a frequency around 6.4 kHz can insonify swathes on the seafloor up to 60 km wide. In addition, single channel seismic, 3.5 kHz high resolution profiles, precision echo sounding, magnetic and gravimetric data all combine to provide as complete a regional interpretation as possible. The GLORIA system combines surveying at a reconnaissance level, covering as it does up to 20,000 sq.km per day, with a very high reliability, so that even in- economically unfavourable times, it can-still be considered as an invaluable and cost effective primary exploration tool. Analysis of the GLORIA data enables the identification of areas of particular interest requiring more detailed study by the more costly multi-channel seismics at a later date.

Jan 1, 1987

By F. R. Hewitt

The methods of mining talc are simple, and in western North Carolina are almost entirely by open cut and quarry. The larger part of the talc of this section lies in various-sized "veins''. inclosed in quartzitic walls, the majority of which have by folding been thrown into a perpendicular position, or nearly so, and the exposed edges of which have been covered by debris from erosion of the mountain above. This covering of loose rocks and earth is from 5 to 25 ft. thick, and in most cases has to be removed because it is difficult to support. Sometimes the covering is heavy enough to "catch" and timber successfully, and in this case the talc can be worked out by the usual method of following the "vein," using stulls for holding up the walk until the vein is worked out, and then allowing the cut or drift to fall in. In some cases it proves more convenient to sink shafts and run drifts, following the talc "veins" until exhausted. The talc deposits of this section are badly broken and faulted both laterally and perpendicularly, and in some cases are found many feet below the level of drainage, necessitating pumping at considerable expense. My own experience in mining talc has been that the chief point is to get a reliable "vein," and that then the mining is not as difficult, or any more so at least, than that of any common ore. If the "veins" are pure talc it is simple; if the talc is admixed with foreign matter, such as tre-molite in excess, or stains of iron or manganese, as is often the case, one had better abandon the deposit. Methods of Manufacture Talc, being a soft mineral, is not difficult to reduce to the condition desired by the trade. Powdered talc is admitted under low duty from France, Italy and Austria, and some is being imported from Asiatic points. Talc is usually ground and bolted in any simple reduction mill. That mined in this section is hand-sorted and the quality that will make good powdered talc is ground for use in the manufacture of talcum powder, cosmetics, etc., while all that is hard enough and has sufficient strength is used for crayons and blanks for gas burners and electrical work, being sawed into the shapes desired. The rest that is clean and pure is ground

Jan 1, 1917

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By McKenzie C. K, Stewart R. S, Simpson J

Blast control in small scale underground mining leads to improved fragmentation control, improved control over overbreak and dilution, and the optimisation of drilling and charging operations. Greatly improved control can be achieved through blast monitoring, to confirm proper implementation of blast designs and blasthole charging. Further improvements can be achieved through simple modelling, enabling blastholes to be placed in the correct locations and charged with the correct weight and strength of explosive. Improved design can be shown to significantly reduce overbreak and dilution, and even ground support costs. In one mine in Quebec, open stopes of widths varying from 2.5 metres to four metres and dipping at 36¦ to 38¦ were designed to achieve zero dilution using open sloping blasting practices. The first stope designed in this manner was monitored in detail and achieved its objective.A method for contouring damage around blastholes is presented as a basis for selection of drilling patterns, with particular application to the control of overbreak and dilution. Contouring can be used to provide reliable estimates of either overbreak or damage (where rock is broken het reynainc in nlarr)

Jan 1, 1993

By D. L. Katz

In the management of oil properties, it is always desirable to know the future behavior of oil wells and oil reservoirs. Some estimation of the quantity of oil and gas that will be produced must be made as a basis for decisions on possible returns on investments in lifting equipment, drilling of additional wells, and other operating expenditures. In new or wildcat areas, operating expenditures are considered highly speculative, but in the completion of partly drilled and the operation of producing fields it is good business to remove as much speculation as possible. An accurate knowledge of oil and gas reserves in such cases would solve many management problems. The term "oil reserves" usually signifies the future ultimate recovery without specifying the method of production. Thus with changing methods and innovations in the production industry, reserves of any definite reservoir may be increased by increasing the portion of oil recovered. The usual reserve estimates are made by comparisons of well and formation characteristics, by using a percentage recovery on the oil content of the formation volume using porosity data, by extending production curves on non-prorated wells, or by extending bottom-hole pressure-production curves. The most reliable method would appear to be one that would estimate the initial quantity of oil and gas present and then obtain percentage recovery values for various productive methods and formations from experience. It is the purpose of this paper to describe a method of estimating the initial quantity of oil and gas present in a reservoir. The method is based on field operating data and the properties of crude oil-gas mixtures. The principles involved, the data required, the assumptions necessary, and an example of the method will be given. The method is entirely independent of sand volumes and formation porosities. Principles of Method The method of estimating the initial quantity of oil and gas present is based upon the premise that the volume occupied by oil and gas in the reservoir is constant and that a mixture of crude oil and gas will behave in

Jan 1, 1936

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

By Harry A. Lipsitt, Rollins E. Hook, Attwell M. Adair

A necessary condition for a uniaxial stress distribution in compression testing is that the specimen end surfaces make full contact with the apparatus compression plates. In addition all compression surfaces must be machined perpendicularly to the loading axis. In general this condition is not sufficiently fulfilled in a simple apparatus. Therefore on application of the load the compression plate may first touch the specimen at one point only. This may cause crumbling of the specimen if the material under investigation is brittle (e.g., ionic crystals). It also precludes a precise study of the beginning of deformation as the effective cross sectional area is unknown. In addition a complex stress state is set up which renders quantitative work impossible, e.g., on dislocation density and arrangement as a function of stress. To overcome these difficulties a "self-adjusting" upper compression plate is required. A simple and reliable method of achieving this is shown in Fig. 1: A steel hemisphere is placed on the specimen. As soon as the compression plate (which no longer needs precise machining) makes contact with this hemisphere the load is uniformly distributed over the whole specimen surface, and a homogeneous uniaxial state of stress results. An advantage of the method is that the loading is always central, even when the specimen surface is not parallel to the compression plate (Fig. 1, dashed line). Therefore to a first approximation a uniaxial state of stress is maintained if the misorientation of the specimen end surface is small. Two typical stress strain curves of identically prepared sodium chloride crystals are shown in Fig. 2; curve 1 was taken without and curve II with the hemisphere under otherwise identical conditions. The improvement in the accuracy of defining the beginning of elastic and plastic deformation is clearly indicated. The writer wishes to thank the Deutsche Forschungsgemeinschaft for financial support, and Professor P. Haasen for providing facilities for this work.

Jan 1, 1962

By D. L. Katz

In the management of oil properties, it is always desirable to know the future behavior of oil wells and oil reservoirs. Some estimation of the quantity of oil and gas that will be produced must be made as a basis for decisions on possible returns on investments in lifting equipment, drilling of additional wells, and other operating expenditures. In new or wildcat areas, operating expenditures are considered highly speculative, but in the completion of partly drilled and the operation of producing fields it is good business to remove as much speculation as possible. An accurate knowledge of oil and gas reserves in such cases would solve many management problems. The term "oil reserves" usually signifies the future ultimate recovery without specifying the method of production. Thus with changing methods and innovations in the production industry, reserves of any definite reservoir may be increased by increasing the portion of oil recovered. The usual reserve estimates are made by comparisons of well and formation characteristics, by using a percentage recovery on the oil content of the formation volume using porosity data, by extending production curves on non-prorated wells, or by extending bottom-hole pressure-production curves. The most reliable method would appear to be one that would estimate the initial quantity of oil and gas present and then obtain percentage recovery values for various productive methods and formations from experience. It is the purpose of this paper to describe a method of estimating the initial quantity of oil and gas present in a reservoir. The method is based on field operating data and the properties of crude oil-gas mixtures. The principles involved, the data required, the assumptions necessary, and an example of the method will be given. The method is entirely independent of sand volumes and formation porosities. Principles of Method The method of estimating the initial quantity of oil and gas present is based upon the premise that the volume occupied by oil and gas in the reservoir is constant and that a mixture of crude oil and gas will behave in

Jan 1, 1936