Search Documents

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l'excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d'analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950

By Manfred G. Raschke

INTRODUCTION In the past decade, the international coal trade has been undergoing a period of gradual change. This change will continue through the remainder of this century until by the year 2000 the international coal industry will look very different from the industry which existed in the early 1970's. The industry which will emerge from the thirty year period of change (1970-2000) will be different in many ways. -The volumes of coal transported will be much larger. - The primary type of coal traded will be steam coal rather than metallurgical coal. - A much broader group of countries will be participating in the trade both as suppliers and as consumers. - The trade will be dominated by a relatively small number of large producing and trading companies. - The coal mined for international shipment will be primarily surface- mined. – The United States will play a decreasingly important role in international coal trade. In the course of this paper I propose to address three questions which are crucial to the formulation of an understanding of the changes outlined above : (1) Which supplier nations will be most successful in the international metallurgical and steam coal trade in the next decade and a half? (2) What emerging trends will shape the international coal trade in the 1980's and 19901s? (3) Where are U.S. producers likely to fit in this scheme of things? As a background to my remarks, I should note that what follows is based on five years of work in a consulting capacity on coal supply and demand issues worldwide. Although in the course of this work I have had occasion to develop mining and transportation cost figures for all of the countries discussed below--both my own and those obtained from coal producers--it is apparent that success in the marketplace can be determined in some instances by considerations other than costs. Nevertheless, my comments today about international competitiveness will be dominated by cost considerations; there are, after all, not many markets that reward the high-cost producer with success. Let us begin by establishing some criteria for success in the international coal market and then compare some of the producer nations to some of these criteria. The criteria are: - Low delivered cost, - Good quality coal, - The producer's partnership in a joint mining venture with an importer or a consumer of coal, - The producer's international business orientation and commitment to penetrating the market, - The producer's reliability as a supplier, and - Political pressure exerted by the producing country on consumers.

Jan 1, 1986

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By W. C. Hagel

Previous inuestigators have repovted unusually low H* and Do values for self-dzf@szon in certazn bcc metals, e.g., chromium nnd y -uvanium. It has been postulated that this is nn experimental crl -tetion for the existpnce of a four -atom ring meclzanzsm, mid there could be. zmpovtant theoretrcal Implicatlons. By utilizing a precise sectioning technique with Cr51 as the tracer, self-dzffi-lsion measurements in large grains of 99.99-pct Cr were extended from 1200° fo 1600"C. A least- squares analysis of the data yields that D 0.280 exp (-73,20U/RT) cm2 sec-'. These AH* and Do unlues are not anomalous; there is little reason to believe that n vacancy mechanism is not opevatiue. Apparent differences at lower temperatures may result from preferential diffusion along short-circuititing paths and/or sample contamination. WITH continued technological effort, chromium and chromium-base alloys should ultimately become useful high-temperature structural materials. Accurate measurements of self-diffusion coefficients in the pure metal are necessary for a quantitative understanding of sintering, grain growth, creep, and other related rate processes. However, two conflicting determinations have been reported.* Using an Since careful diffusion studies normally yield Do values ranging from 0.1 to 10 cm2 sec-l, the Paxton-Gondolf results require independent experimental corroboration before an undue amount of speculation arises to explain the apparent anomaly. As discussed by Nowick6 and clearly shown by Hoffman and Turn-bull7 for self-diffusion in silver, a low AH* and Do can arise from preferential diffusion along grain boundaries or other short-circuiting paths. The most reliable data come from high-temperature measurements where volume effects predominate. Following a precise sectioning technique developed for determining silver diffusion in the intermetallic compound AgMg8 and cation diffusion in the corundum oxide Cr2O3,9 the purpose of this study was to measure true volume diffusion in high-purity, large-grain samples at higher temperatures than considered previously. Another point of interest is the frequent proposal10-12 that chromium undergoes an allotropic transformation between 1375" and 1800°C where the diffusion data might then show a discontinuity. I EXPERIMENTAL 1) Sample Preparation. The highest purity (99.997 pet) Cr currently available is produced by reduction of chromium tri-iodide. Three pounds of the resulting crystal bar were shipped in a sealed container with a complete chemical analysis from the vendor.* In conformity with the procedure used for

Jan 1, 1962

By Carl F. Floe, Michael B. Bever

TRE solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to 1300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. REVIEW OF PREVIOUS WORK The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available. According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar6 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwas3é reported large hydrogen solubility values for several compositions of copper- tin alloys, which appear to be in error.

Jan 1, 1944

By C. I. Pierce

Knowledge of the water content of oil-bearing formations is important in petroleum-reservoir evaluation work. Electric logging provides a means for making reliable estimates of water content if resistivity-saturation relationships representative of the formations are available. Relationships can be determined in the laboratory by a number of methods. This report describes and presents results of a laboratory investigation conducted at the Bureau of Mines Appalachian Experiment Station, Morgantown, W. Va. (1) to evaluate an evaporation method of attaining water saturations in sandstone samples when determining resistivity-saturation relationships and (2) to compare saturation exponents derived from data obtained, using different methods of achieving water saturations. A series of tests was conducted to determine the effect of evaporation on salinity distribution within the core specimen. Results of these tests show that a zone of high salinity was set up at the surface of a sample during evaporation and that long periods were required for the sample to reach resistance equilibrium after evaporation had ceased. Equilibrium time ranged from several minutes to several days, depending on the sample size and the technique used. The high-salinity zone was removed from the sample by using auxiliary porous material in capillary contact with the sample surface during evaporation. Salinity determinations and resistance measurements indicate that, at saturations greater than the minimum interstitial values, the mechanism of flow during evaporation was one of moisture migration mainly as a liquid from the interior of the test specimens to their exterior surfaces. The concentration of the contained brine remained essentially unchanged, except for a narrow zone near the evaporating surfaces.

Jan 1, 1958

By J. Partyka

Respirable dust produced during blasting operations in underground mines exhibits both diffusion and convection properties of the airflow. However, the application of the mathematical model presently used to calculate the change in time in the concentration of blasting pollutants is mostly limited to a single drift and cannot be easily utilized for blasts taking place in stopes. This paper discusses an analytical solution based on considerations that enable us to reliably identify the initial condition. Such an approach may be used for any blasting area regardless of its position, its size, or the ventilation system in use during blasting. In addition, a test procedure using field data is established to determined those parameters not measured directly. As well, equations are derived to find the diffusion coefficient, and the position and size of a dust source from the field data. Mathematical considerations The convection-diffusion problem, for a one-dimensional case, is described by the following partial differential equation (PDE): ct. = Dcxx - Vcx + source - sink(1) where C = the concentration of a pollutant T = time V = the mean air velocity in x-direction D = the diffusion coefficient X = distance away from the pollutant source source = any additional pollutant source specified by an initial value problem sink = decay of a pollutant inside the region specified by the boundary conditions. Respirable dust produced during blasting is best considered as an initial value problem (IVP). To derive a mathematical model, the following assumptions are made: •At time zero (t = 0), the dust source is at point x = 0 of an infinite drift. •The problem is considered a one-dimensional case. •The mean velocity of air and the diffusion coefficient are constant. •There is no source or sink of dust other than specified at point x = 0 and time t = 0. We have to solve the following problem [PDE ct=Dcxx-Vcx-m<x...m;0<t<m(2)] ICc(x,0)=f(x)t=0, the initial condition Where c = dust concentration in mg/m3 V= the average mean velocity in a drift in m/s t= time in s D= the diffusion coefficient in m2 /S x = distance coordinate in m. We observe that in problem (2), we have moved the boundaries to[ -m and +m] in order to have an initial-value problem. We introduce new coordinates, s = t and z =x - Vt. To rewrite the PDE in terms of (z, s), we use the chain rule ct = czzt + csst = -Vcz + cs cx = czzx = cz cxx = (cz)x = czz. We now substitute our computed ct, cx. and cxx into the PDE to get new IVP in terms of z and s :

Jan 1, 1991

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

By Malcolm Scobie

"This paper reviews the evolution of Canadian surface and underground mining automation, principally relating to: advances in communications, initial development of machine teleoperation from line-of-sight remote control, and islands of automation. The eventual role of teleroboties and minewide robotic mining remains to be resolved. The progress and approaches adopted have tended to vary within each sector of the mining industry. Recent information technology advances have made possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using new communications technology. The Digital Mine will provide the information infrastructure to serve as the foundation for minewide automation. This paper concludes by reviewing the issues likely to govern implementation success, relating to: mining process design, machine design, machine intelligence, and mine planning and control.IntroductionSignificant advances have recently been made in underground hardrock mine communications and teleoperation. Subsequent R&D efforts are mainly focussing on control systems for various types of machines. In underground potash mining, the realization of automated continuous mining systems appears to be imminent. Recent advances in surface mine dispatching, machine monitoring and global positioning systems (GPS) have tended to reactivate some of the initial R&D enthusiasm developed in the &apos;70s for surface mine automation. Mines at large are approaching a major milestone: the implementation of comprehensive communications infrastructure which proves to be sufficiently reliable and economical to support the automation of routine mine production, either using teleoperated or autonomous machines. This then should motivate a deeper commitment to real time monitoring and management. The communications advances make possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using information engineering. The Digital Mine will provide the information infrastructure to serve as the likely foundation for a wide range of automation scenarios. This paper surveys the status and directions of automation development in both surface and underground Canadian mines, pointing to what are seen to represent key technology development issues."

Jan 1, 1995

By I. N. Knapp

I Herewith present some notes on the use of Portland cement to cement in the casing, and for plugging, to exclude water from oil and gas wells, and the methods employed. I have used my best efforts to. make each step of the operation of cementing wells perfectly clear. The information is the result of actual experience and observation. The illustrations are from original drawings made especially for this paper. Portland Cement It is not necessary to discuss here the manufacture of cement. Any established brand of the slower setting Portland cements may be purchased with the confidence that it will harden, if properly used, and exclude water from and plug wells efficiently. Setting.—By the setting of cement is meant its initial change from a soft or plastic mortar to a friable solid. After the cement has become thoroughly set it is still very weak and can be readily pulverized in the fingers. Setting is thought to be effected by the crystallizing out of the silicate and the aluminate of lime, which are soluble in water in their anhydrous form. After dissolving in the water they pass to the hydrated state, in which they are insoluble, and hence are precipitated in a crystalline form. Ordinarily neat Portland cement mortar remains perfectly plastic for from 1 to 1 1/2 hr. after mixing with water at about 70" F. A higher temperature accelerates and a lower retards setting.. Hardening.—This is due to a continual crystallization of salts from solution, and to further chemical and physical changes which develop slowly, but which continue for long periods of time. Testing.—It is no more necessary for an operator to go into the scientific testing of cement to be used in a well than to so test the pipe used. He must depend for the quality of each on the tests and reliability of the manufacturer. Cement or pipe may be damaged in shipment so

Jan 1, 1915

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)&apos;:• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

By A. Buncombe

In March 1984, two years&apos; work by senior metallurgical personnel from the six major mining groups culminated in the formation of the Mine Metallurgical Managers&apos; Association of South Africa. This Association has joined a group of specialist Associations operating within the South African mining industry whose aims are to uphold the standards and promote the interests of their various professions.

Jan 1, 1987

By Barbara A. Filas

The IFC goal is to promote private sector investment in developing countries which will reduce poverty and improve people?s lives. The developing country goal is to promote health, education and employment opportunities that improve their economies and their standard of living. The mining company goal is to Promote successful ?triple bottom line? mining projects that will grow shareholder equity

May 1, 2002

By Bearman R. A, Parkin R. M

In the comminution industry cone crushers are widely used for secondary and subsequent stages of size reduction. Traditionally cone crushers have been operated and monitored manually. Alteration of discharge setting is now commonly achieved via hydraulic means, however, compensation of liner wear can still involve plant shutdown and loss of production. Drift in discharge setting due to liner wear is still a major problem that must be addressed to improve product quality, consistency and reduce recirculating load. The continuous demand for better quality products and the high cost of reprocessing or discarding unsaleable material, highlights the need for re-examination of the technology associated with the crushers to ensure optimum control and system efficiency. A collaborative project between Pegson Ltd, one of the leading UK manufacturers of jaw and cone crushers, De Montfort University Leicester, and Transfer Technology plc was established to address the technological requirement for automation of the control of cone crushers. The machine chosen for the study is a 900 Autocone cone crusher manufactured by Pegson Ltd. The design philosophy is based on a mechatronic approach providing a complete solution through a distributed network of intelligent sensors, artificial intelligence technology and adaptive control. The modular design of the system ensures a progressive sophistication in technology that allows the automation to be phased in as required. This will ensure maximum benefits to all sectors of the aggregate industry. It is estimated that the automation will result in savings of around ten per cent. The savings will result from minimising the production of unsaleable products by reliable condition monitoring and automation of the control and maintenance of system parameters to optimise system efficiency. Extension of the methods and principles into the mining sector is anticipated. The control over the size of crusher product will offer great benefits to the mining industry with significant implications for subsequent milling and beneficiation processes.

Jan 1, 1995

By L. H. E. Weyher

A mine is essentially a vast materials-handling system. All other systems found in the mine exist to one degree or another to support the materials-handling functions, from the cutting at the face to the hoisting in the shaft. In this chapter computerized planning of underground materials-handling systems will be examined by dividing this function into: (1) the planning of the production section, and (2) the planning of underground rail or belt haulage from the production section to the shaft, slope, or surface. While alternative divisions might focus on the different materials- handling functions, i.e., production, supply, and manpower transportation, historical computer analysis has focused on the various systems rather than functions. The emphasis in this chapter is directed toward coal mine applications; however, most of the programs and methods are equally applicable to other underground mines. Markedly different methods are encountered in each system, and moreover, marked differences exist in the nature and the degree to which the materials-handling subsystems in each interact with the environmental or support systems. The most intimate interaction exists at the faces where geologic, human, and machine performance factors are closely related and constantly varying. In view of this, the planning of the materials-handling systems for the face will usually stress flexibility, while the outby materials-handling systems will generally place decreasing emphasis on flexibility and more on system reliability, capacity, and cost effectiveness. Thus, hoisting and main haulage systems are generally designed and constructed as permanent installations and cannot be readily changed, whereas secondary haulage systems and face operations are relatively mobile. These differences may have considerable significance for the mine planner in making technical and financial comparisons of alternatives to provide the scheduled mine production.

Jan 1, 1979

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.