Search Documents

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By R. L. Grayson

"Compliance standards for respirable dust, which are reduced because of high quart: concentrations, have become an industry-wide problem. Research on the physical and chemical character of quart-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quart: particles of a mine dust are ""pure,"" then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. lf, however, quart: is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.Although much research has been done on coal workers' pneumoconiosis (CWP) over the past decades, the etiologic agents of the disease still have not been pinpointed. The predominant methods of characterizing respirable coal mine dusts were bulk analysis techniques for determination of elemental and mineralogical concentrations, the results of which were used in statistical analyses to determine relationships between dust composition and the occurrence of CWP. These methods are incapable of finding the etiologic agents in the dust primarily because of complicated and confounding physiochemical factors, which may be discovered if the focus of characterization was done on a dust particle level.The SEM/EDXA-based research discussed here shows a significant difference in the number of ""pure"" quartz particles in respirable dusts collected from different mines. Some of the results have been reported previously (Grayson, Andre, and Simonyi, 1988). Concurrent research by other investigators (Wallace et al., 1989) demonstrates an SEM/EDXA-based methodology to pinpoint the location of the ""contaminating"" substance(s ) in a quartz-classified particle. The research of the European Economic Community has also begun analyses on the respirable-dust-particle level (Robock and Bauer, 1988).Since the compensatory and intangible costs of CWP are substantial in the United States, it is important that the etiologic agents be determined and then either controlled or neutralized in a cost-effective way. This line of research is especially important consid-ering the forecasted. near-term growth of coal production and the evolution of high productivity longwall panels (an immediate problem in compliance) and continuous mining sections ( a probable future problem).This need has been accentuated now that nearly all respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gem, 1986). Today a real problem exists in the coal industry, both underground and surface, because of high quartz levels in respirable dusts causing substantially reduced compliance standards (Murphy, 1989).The combined results of the respirable dust particle investigators indicate that conventional bulk sample analyses may not faithfully represent the amount of biologically available or active quartz in all mines with a high level (greater than 5% ) of quartz in the dust For example, some mine dusts might contain predominantly occluded (or coated) quartz particles where bulk analysis would result in anomalously high ""free silica"" measurements. The same result would occur when quartz particles are intermixed substantially with other minerals that can alter the surface of the composite particle away from a quartz-behaving character."

Mar 1, 1992

By Jan M. Mutmansky

"When, in 1973, a limit was placed on the amount of dust in the coal mine atmosphere, restricting the average exposure of a coal miner to 2 milligrams of dust per cubic meter of air (mg/m'), skeptics in the United States and abroad Said the standard could never be achieved. They cited much more lenient standards already established in other countries and refused to believe that the United States could meet the world's most stringent requirements in mines where dust had never before been regulated. Yet 10 years later the goal had largely been achieved and miners were working underground in a cleaner atmosphere than ever before. It was a major achievement and a big stride in what had become a war on coal workers' pneumoconiosis (CWP), the black lung disease prevalent among miners in underground coal mines.Although the health hazards caused by working in a dust-filled mine atmosphere have long been recognized, the problem became particularly acute in this century with the mechanization and increased productivity of underground coal mining. The United States was much slower than some other countries to address the problem of respirable diseases among miners. While dust levels in South African gold mines were first regulated in 1912, in the United States it was only when 476 workers died of silicosis while blasting a tunnel through a mountain near Gauley Bridge, West Virginia in the 1930s that widespread public attention became focused on the plight of workers in dust-filled environments. Another 30 years passed before regulation of dust finally became law in the Coal Mine Health and Safety Act of 1969.With a stringent new standard imposed in all underground coal mines, the industry was faced With the daunting problem of reducing levels of airborne dust from perhaps 6.5 mg/m' to 2 mg/m', in an inherently dusty operation carried out in the close confines of underground passageways. Most of the coal dust is made by the cutting operation in which the continuous miner or longwall machine can produce several thousand milligrams of respirable dust for each ton of coal mined. Other dusty operations such as drilling holes for roofbolts, loading and unloading coal on shuttle cars, and the operation of conveyor belts contribute to the overall problem.Since the institution of the new dust control standards, a number of strategies have been adopted for reducing the coal dust in the mine atmosphere. These strategies involve engineering and design improvements that help lo prevent the generation of particles, keep particles of dust from becoming airborne, carry dust away from the working area, and isolate the dust from the workers in the mining operation. These procedures have been pursued vigorously by the Bureau of Mines, and many successful methods have been developed to reduce the mass concentration to which the workers are subjected. The mining companies were reluctant at first to confront the problems but after a period of trials and gradual improvement, they joined with others in the fight to reduce the dust concentrations in the working place."

Jan 1, 1990

Oxidation or sulphidization of the surface of pyrrhotIte partIcles enhances atomic interdiffusion at elevated temperatures and provides a mechanism for interface growth between particles in contact. In a mass of pyrrhotite-rich ore or tailing, where oxidation heating is not controlled, bonding of particles by diffusional mass transport contributes significantly to the agglomeration of the mass.

Jan 1, 1976

By M. B. Bever, J. E. Reynolds

IN several alloys of iron, copper, and lithium as well as in some pure metals, martensite formed on cooling reverts to the parent phase upon heating to a temperature below the equilibrium temperature at which the parent phase becomes stable.' These martensitic transformations, therefore, are thermally reversible, although appreciable hysteresis may be involved. The martensitic reaction has long been

Jan 1, 1953

The paper describes a simulating method.for ground water contamination originating from industrial and mining activrty. The finite difference model simulates heat, mass and solute transport. The applied stochastical method for dispersion provides more accurate solution of mass transport modelling. This method gives a more realistic approach of chemical processes in an aquifer depending on temperature.

Jan 1, 1988

By Herbert A. Stein, John B. Murdock

Perlite is a natural volcanic glass which expands into an insulation material upon the application of heat. This paper discusses the operating characteristics of eight different types of furnaces for the expansion of perlite. It also includes a section on the theory of perlite expansion which serves as the basis for the authors' analysis of the furnaces.

Jan 1, 1950

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

Track and control the tram maneuvers of continuous mining machines by developing and evaluating a laser sensor system. Background Progressive technology has the potential to greatly improve mine-worker safety, helping to create a safer, better working environment for mine workers by keeping them away from the dangerous face area. To benefit from such technology, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A cornerstone for computer-assisted operation is an effective guidance system. Since there are no guidance systems on any commercial continuous miners (CM's), the Bureau it-self developed and tested a laser-based sensor system, based on a commercial sensor called Lasernet. The laser-based guidance system employs four laser scanning sensors at fixed locations in a mine entryway to report the angular coordinates of two cylindrical retro-reflective targets mounted on a CM. Using triangulation, a real-time microcomputer system processes the sensor data and updates the xy position and heading (h) of the CM five times per second. Using a simple control algorithm and communications interface to the CM control computer, the system also controls rotational and translational tram maneuvers.

Jan 1, 1992

Overview n Why we audited the IRS n How we did it n What we discovered n What we learned n Where we are going next The unbroken chain of safety The Internal Responsibility System (IRS) The network of roles and relationships in a workplace, through which everyone works with mutual commitment to reduce or eliminate hazards.

May 1, 2003

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

By John Gross

"Introduction.Southern Illinois and Kentucky are credited with approximately 90% of the fluorspar production of the United States. A small amount of high-grade acid, spar is obtained from the ore by band sorting; the greater part, however, is recovered by jigs and tables as gravel spar containing approximately 85% calcium fluoride. In the jigging and tabling operations, galena is recovered, and enough silica and calcite are removed to raise the calcium fluoride content of the gravel spar to 85%. However, the removal of silica and calcite results in a large loss of spar. With increasing depth in the mines, zinc sulphide, sphalerite, is encountered in increasing quantity and the removal of this has become a serious problem. While the sphalerite can be fairly well removed from the spar by present milling methods, a marketable zinc concentrate can not be made. The experiments described below were made on fluorspar ore from Southern Illinois, by the mining experiment station of the U. S. Bureau of Mines, at Rolla, Mo., in cooperation with the Missouri School of Mines and Metallurgy.The ore tested contained. 7.3% lead, 27.9% zinc, 35.7% calcium fluoride, 9.5% silica and 4.7%. calcite.Tests and Results. In some preliminary tests it was noticed that a portion of the finely crushed ore adhered strongly to the sample pans, and upon investigation it was found that the adhering material was practically clean spar. By utilizing this property of adhesion 46.8% of the spar was recovered as a product containing 98.3% calcium fluoride. This suggested the possibility of using electrostatic separation."

Jul 1, 1921

By Sherwin F. Kelly

NEW trend in geophysics has been uncovered in these depression years, made evident through the thinning cloak of commercial activity, which, in better times, would have completely obscured it. I refer to the increasing use of these methods for geological investigations by federal and state geological surveys. This is a trend that has been gathering momentum not alone in the United States, but abroad as well. Thus, in Poland, the Geological Survey has been playing an increasing role in geophysical work since 1927, and now has- its own geophysical department. The government petroleum producing organization of Argentina has its Geophysical Commission; Brasil boasts a completely equipped geophysical department in its Mineral Production Service; the government of Chile has contracted with commercial companies for geophysical surveys; Peru is planning an intensive program of geophysical prospecting in its petroliferous regions; and Canada has, for several years, cooperated with

Jan 1, 1935

By Mario Teruo Enju

Soluções flexíveis, com baixo custo de implantação e manutenção, de sistemas de controle de processos e informação utilizando tecnologias de ponta desenvolvidas em plataforma .Net Framework. Focadas inicialmente em área Metalúrgica, onde eficiência em custos e alta confiabilidade tem relevância fundamental para sua viabilização econômica, estas soluções podem também ser aplicadas em áreas Siderúrgica, Petroquímica e demais segmentos. Integração das informações do chão de fábrica com o sistema de gestão da empresa com objetivo de facilitar a tomada de decisões estratégicas. Banco de dados relacional é o principal repositório de dados para compartilhar informações com a rede corporativa, gerenciado por uma ferramenta de software em tempo real para as lógicas de negócios e camada de apresentação. Maior performance, facilidade de operação, disponibilidade de dados, OEE, manutenção simplificada, acesso e ações remotas são viabilizados, permitindo menor custo e maior eficiência.

Jul 30, 2018

By A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The U.S. National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two-phase implementation of an IoT-based intelligent machine monitoring system.

.MAX ROESLER, Firmeza, Oriente, Cuba (communication to the Secretary?).-It is substantially admitted by all who have recently been in touch with these deposits that the orebodies lie in the fine-grained dark-green rocks, called diorite by most writers and diabasic by myself. The three points of disagreement concern the agency of included limestone blocks as causes of deposition, the agency of the

Jan 5, 1917

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024