Search Documents

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By Richard D. Divine

In the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. TO do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000" C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seems to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues. There has been considerable difference of opinion regarding the effect

Jan 1, 1915

By John Howe Hall

The recently announced run of three years, nine months and eleven days made by a crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemens regenerative crucible melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators, of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter: Design, nature of refractories, and conditions of operation (including the nature of steel melted); and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to be operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure repeated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of heat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable—and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting time than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted. The figures available, showing the life of furnaces, are for this reason especially not strictly comparative, since the variations in the steel melted undoubtedly affect the life to a greater or less extent. Probably, however, the method of handling is as important a factor

Jan 1, 1914

By Richard Divine

IN the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and, some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. To do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the. top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000°C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seen-is to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues.

Jan 8, 1914

PAUL. D. MERICA, Bayonne, N. J. (written discussion*)..-The mode of intercrystalline oxidation which the authors" have so well observed and described is characteristic of nickel that has been exposed' to: the action of an oxidizing atmosphere at higher temperatures, such as, those at which; it is annealed or heated for rolling or forging. Oxidation under such conditions proceeds inward from the surface along the, crystal boundaries' producing a net-work, probably of oxide; which causes a very brittle condition of this surface material. This, in turn, generally results in surface cracking and checking during further, rolling and a defective sheet or other product is produced. An example of this is shown in Fig. 2, which shows the surface, of a badly surface-cracked sheet of nickel produced by incorrect heating con-ditions. A cross-section of this sheet etched with nitric acid is shown in Fig. 1, which reveals the intercrystalline oxidation network adjacent to both surfaces.These layers are so brittle that it is not possible to deform them by rolling without severe cracking along these lines or, planes of weakness. The best, and possibly only, remedy for this condition lies in its prevention by the maintenance of a neutral soft flame for heating and annealing nickel during the entire course of its manufacture. I should like to suggest that, those making microscopic investigations of nickel and nickel-rich alloys try the use of acetic-acid .solutions of nitric acid for etching these metals rather than aqueous solutions, of nitric acid. I have found that a solution containing 50 per cent. nitric acid, from 25-45 -per. cent. acetic acid, and from 25-5 per cent. water gives excellent results with. Wrought and cast nickel and Morsel metal and superior results to those obtained with nitric acid, alone. The acetic. acid seems to inhibit the passivity that nickel often assumes toward nitric acid and much more uniform etching may, be obtained. The proportions of nitric and acetic, acid may be varied somewhat from those given without mate-rially altering the quality of the etching, although without any distinct improvement in it.

Jan 12, 1919

By Rudolf Kudlich

"The realization that fuel costs, high as compared with those enjoyed prior to the war, are apparently permanent, has caused steam power plant operators to apply their best efforts towards improving the fuel economy of their plants.Though they have given much attention to the reduction in combustion losses by improving methods of firing and improved equipment, and to diminishing the heat losses by more care in maintaining clean heating surfaces and tight and adequate baffling, they have almost universally neglected the waste that occurs from discarding unconsumed combustible with the boiler refuse.This loss varies between extremely wide limits, depending on the quality of the coal, the type of plant and the firing practice in general, the higher the ash content of the coal the greater will be the amount of combustible appearing in the refuse, and the losses will be greater as the boilers are driven at higher ratings. The refuse from stoker fired boilers is apt to have a lower aver-eve percentage of combustible than that from hand fired boilers if operated at the same rating, but stoker fired boilers are usually pushed to higher ratings and the combustible in the refuse will run higher.In actual operating practice the amount of unconsumed combustible in the boiler refuse may range from a few percent to as high as forty or fifty percent. In an informal statement one well known combustion engineer estimates that the average amount of combustible in the refuse from a large stoker fired central station boiler plant is about 15 or 20%. Assuming that the coal burned contains 12% of ash, and allowing for flue dust losses, approximately two percent of the coal will be lost through this channel. The operating engineer of one large modern central power plant reports that when burning coal of about the same ash content, the average amount of combustible in the refuse was in the neighborhood of 33%, en tailing a loss of approximately 4% of the heating value of the fuel fired. Where the coal used daily runs up into hundreds of tons, an appreciable economy could be effected by recovering this percentage."

Sep 1, 1924

By R. A. Wagstaff

The method of charging a reverberatory furnace has changed many times since smelting was introduced in this country from the old smelters of Swansea, England. The cause of the latest change at the Garfield plant has been the excessive fineness of the charge due to fine grinding in the concentration of the crude copper ores. The many desirable features of deep-bath smelting as now used at Garfield have been proved. The old method of dropping the charge through holes in the arch (known as center-feed method) causes excessive dusting which makes heavy slag and flue-dust losses, also rapid deterioration of the silica brickwork of the furnace through fusion with the iron oxides from the dust. The purpose of this paper is to describe a gun feeder that was designed to overcome the disadvantages of the older methods of center feeding and still maintain the good features of deep-bath smelting with the hot finer charge. A gun feeder was designed to introduce the finely divided hot calcines under the moving gas stream of the combustion zone and still have them spread in a uniform blanket over the highly heated matte bath. The temperature of the furnace was so great that it was impossible to maintain a stationary feeder, so a movable feeder was designed that could be introduced into the highly heated zone and be withdrawn after the charge had been dropped. It was necessary to protect the nozzle of the gun with a water-cooled coil. Many different types of protected nozzles were tried, such as air jackets, water jackets and heat-resisting steel alloys, but none proved satisfactory. The angle of inclination of the feeder was found to be an important factor in spreading the charge evenly over the surface of the bath. An angle of 34" to 37" was found to be the most advantageous. To allow a continuous flow of ore from the charge car to the point of discharge inside the furnace, the feeder was made with telescopic connections. The pipe leading from the car is stationary and forms the inside part of the telescope. The outside section of the telescope is movable, and is

Jan 1, 1934

By J. O. Whiteley, C. Dietz

It is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. Typical Platinum Scrap As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly. Obtaining Residue A Place the scrap, together with six times its weight of granulated test lead, in a solid carbon crucible. This crucible may be placed inside a clay graphite crucible packed with charcoal, to prevent the excessive oxidation of the carbon crucible by the furnace blast. Place a tight cover on the carbon crucible; heat gradually to a good red heat and allow it to soak in the heat for 4 or 5 hr. After the leaded mass is cool, dissolve in dilute nitric acid (1-6) on a steam plate or sand bath. This dissolves practically all of the lead and most of the palladium, silver and copper, together with seme of the platinum and rhodium, and leaves the iridium, ruthenium, gold, and most of the rhodium and platinum as a finely divided residue. Siphon off the clear solution and treat the residue with another portion of dilute nitric acid to insure the solution of the lead and copper. The second nitric acid solution is added to the first, and the residue is filtered on suction and washed thoroughly with hot

Jan 1, 1928

By R. E. H. Pomeroy

THE statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Me Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. ½ in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5° B., flashing in open test at 199° F. The oil is heated to about 200° F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 lb. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-oz. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and "dog houses? to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent.

Jan 2, 1915

Discussion of the paper of W. R. SHIMER, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 557 to. 585. WILLIAM R. WEBSTER, Philadelphia, Pa.-I would like to ask Mr. Shimer how the finishing temperature of the H-beams and other beams rolled on the Gray mill at Bethlehem compare with the rolling temperatures of the rails referred to in this paper. Also, how the reductions in the rolling of the beams compare with the reductions in the rolling of the rails. I would also like to know if any drop tests were' made on the rails referred to as having been allowed to cool and then annealed; in other words, what results, if any, were obtained from tests on rails after the internal strains of rolling had been removed; and in the matter of the rail blooms, I would like to ask if they are not often heated to a higher temperature than is desirable on account of the thin flanges in order to carry the heat through to the finishing pass. The tensile strength of the steel in these rails is given as 125,000 lb. per square inch, which is almost as high as tire steel. If some of these blooms were rolled into rounds of about the same section as the head of the rail, would you not get better results from tension tests than those from the head of the rail? In other words, in rolling rounds, whether you would not be able to control the rolling and finishing temperatures better than is possible in the rail, owing to thin section of the rail flanges. Some years ago I had experience with the rolling temperatures of tire steel, running from about 127,000 to 133,000 tensile strength. These tires had the tensile strength and the deflection specified. One of the manufacturers had no trouble whatever, after a little experimenting, in meeting the conditions of the specification. Another manufacturer who made some of these tires came to the office and stated that he had tried tires from three heats of steel and could not meet the specifications and

Jan 5, 1915

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By John B. Myers

VERMICULITE is a name used to describe micaceous material that exfoliates when heated. It is hydrated magnesium-aluminum-iron silicate. The chemical composition, color, physical appearance, and degree of exfoliation vary. COMPOSITION, PROPERTIES, AND ORIGIN Vermiculite has the characteristic micaceous structure of basal cleavage and readily splits into thin laminae, which are soft, pliable, and inelastic. The monoclinic crystal faces are often marked by triangular lines at 60° and 120°. Hardness is 1.5; specific gravity, 2.2-2.7; luster pearly to greasy; colors, amber, bronze, reddish brown, dark green, and black. Feel is soapy, particularly when wet. When heated it exfoliates by expanding at right angles to the cleavage into long wormlike pieces (the name vermiculite is from the Latin veamiculari, to breed worms). This important characteristic of expansion is believed to be a mechanical separation of the layers when the contained water is converted into steam. Warping of the unit layers may also contribute to the expansion. The increase in bulk volume of commercially prepared material is 8 to 12 times but individual flakes may increase in size more than this. Pure vermiculite is a distinct mineral and has the structural formula (OH), (Mg,Fe)3 (Si,Al,Fe)4 010.4H20. It rarely occurs in this pure form, but generally as a mixed mineral of varying structure. One explanation is that the mixed material is composed of unit layers of inter-stratified pure vermiculite and biotite. The essential difference between the two is that unit cell structure of vermiculite contains a layer of water molecules whereas the biotite cell contains potassium instead of the water. The water content of the mixed vermiculite is less than that of pure vermiculite but more than that of biotite. Pure biotite does not expand when heated. If the proportion of biotite layers in a vermiculite is too high it will adversely affect the degree of exfoliation. Within a given deposit, the great mass of material may approach a definite com-position with local areas of greater biotite content. It is not uncommon to find also small pockets of pure biotite but these are generally segre-

Jan 1, 1949

By Patzen Wu

The Hai-Shan No. 1 Coal Mine, located in northern Taiwan, is one of the typical coal mines on the island which, limited by natural condition, are mostly small in scale. With the advancing longwall method, the mine is now winning a seam, 80 cm thick, at a 32° dip, with a working depth of 824 m below surface. The annual output is about 50,000 mt of clean coal. At the working gallery, the virgin rock temperature may go up to 46°C, difficult to be brought dam to n acceptable level: because .of the tropical climate with high intake temperature and high humidity. Besides, at this depth, the intake air that goes down the long inclined shaft generates considerable heat due to autocompression. The mine is ventilated by a set of axial-flow fan with 38 m3/S of intake air at 2.2 KPA WG. With this volume of air, the temperature at the working-face is usually above 30°C WB. Appreciable lowering of the temperature is not expected even with an increased volume of ventilated air. For this reason, decision has. been made to try the installation of a pilot underground refrigeration unit near. the lowest gate road to cool the intake. air. from 32°C WB to 28°C WB which seems acceptable to on-the-spot workers exerting heavy physical labor. The experimental unit is designed for carrying away a total heat load of 90 Kw. The capacity of the unit is 200 Kw. The unit consists of a compressor, an evaporator, a condensor and a motor. The heat rejection is done in a cooling tower. Chilled water is circulated from the evaporator to the cooler by insulated pipes. The cooler consists of 90 Kw-coils with two fans and forces air by flexible ducting onto the working face. This paper examines mainly the effect of this additional reduction of working temperature, on working efficiency of the workers. Another aspect of this experiment is to evaluate the overall economy of underground refrigeration in small-sized coal mines under tropical condition. The success of such an experiment may lead to wider application of refrigeration to render many of the deeper mines economically workable.

Jan 1, 1980

By John McDonald

THE amount of published literature in the field of mechanical proper-ties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherch1 have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing&apos; with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in, properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the proper-ties of alloys in conditions where the effect of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these proper-ties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments will produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of working and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treat-ments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloys have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are relatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1939

By George A. Roberts, Robert F. Mehl

WHEN austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.1 This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced,4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ae1.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. EFFECT OF INHOMOGENEITIES ON REACTIONS NEAR Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously;1,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional quantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a "fine-grained steel." These steels can be compared at the same grain size by heating C to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By Henry F. Heblby

HOW often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days1&apos; indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer&apos;s day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. The Sources of Atmospheric PolLution The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is prob- ably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominantly dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh Indicative of the stupendous quantities of fuel that are employed in this industrial area&apos;s economy, the following (Table I) taken from the U. S. Census (1940) may be of interest. In tonnage consumed in the area, the figures are equally impressive: Annual Tons oF Coal Metallurgical Industries.... 35,000,000 to 40,000,000 Commercial Installations (Pgh.)................. 1,500,000 Domestic hand-fired) (Pgh.)................. 750,000 An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, uti-mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1949

By Wm. C. Coffin

THE refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Not only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts clown the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bes-

Jan 2, 1919

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.&apos; This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.&apos; This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943