Search Documents

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min. is required to drain and dress the furnace hearth, make up the tap hole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays, because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of' charge. Such general considerations are dealt with first. GENERAL CHARGING PRACTICE Charge materials are discussed in detail in Chapter IV; the present chapter is concerned with the charging, melting, and proportioning of the raw materials in the various types of furnace practice. Charging Equipment and Stock Handling. The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment described in Chapter I (see also Fig. 18, page 33). It is generally desirable to charge the scrap about as fast as the physical volume can be got into the furnace. A limiting factor may be the height to which the scrap may be piled in the furnace without deflecting the flame to such an extent that it will impinge on the roof or walls and thus damage the refractories, but light scrap may often be piled up near the roof since the flame usually "cuts it down" rapidly before impingement on any roof area can persist long enough to do appreciable harm. When the nature of the scrap and the handling facilities are adequate to meet the aim of rapid charging, little thought is given to this feature of operation. Unfortunately, at times

Jan 1, 1944

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

By Walter McKee

WHEN mixed with common cast steel in quantities ranging from 11 to 13 ½ per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time. Manganese steel has been manufactured for about 26 years. .It was first made in a small way in England and subsequently produced in the United States in 1892. At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 lb. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13 ½ per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 5 ½ in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 5 ½ in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an

Jan 12, 1915

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported' that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.' per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By Karl Fetters

IN the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime are required for phos-phorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantita-tive relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composi-tion encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and are more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By C. S. Sivil

To modern civilization the platinum metals are of inestimable value. Their distinctive properties, both physical and chemical, render them indispensable in an age in which the processes of the laboratory are becoming an essential part of the daily life of the world. Generally, their function, though vital to particular processes, is not spectacular, and so remains unknown to all except the operators. Early Methods of Manufacture The properties of platinum were recognized as of prime importance for scientific work at a very early date, probably between 1750 and 1760. The difficulty of making articles from it seemed almost insurmountable, because no means of attaining the temperature necessary to melt it were known at that time. It is true that solid platinum could be obtained by fusing the metal with a more volatile metal such as arsenic, which was subsequently driven off by baking, but such a method, at its best, would give only a very brittle product, which was totally unsuitable for the purposes for which it was intended. Little, if any, progress could be made until it was discovered that platinum sponge, heated to white heat and hammered in an iron or clay mold, would metallize and retain the shape of the mold. This was a process that could not be wholly satisfactory but from it developed the method of pressing the sponge in a mold and forging it at white heat into wire or sheet. At present a somewhat similar process must be used for fabricating articles of tungsten, molybdenum and other metals of high fusing point, as with these metals we face today the same problems that the scientists of the eighteenth century encountered with platinum, but possibly the next significant advance in the metallurgy of these metals will be the devising of means to melt and cast them. TO some extent this method of preparing platinum has survived, particularly in Europe. There are one or two objections to it, but they are not serious, as they can be surmounted with proper precautions. In the first place, the material is spongy and its millions of cavities contain entrapped air. Unless this is removed by thorough forging above 1000" C. the resultant sheet shows blisters. To give such a thorough forging,

Jan 1, 1931

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By Walter S. McKee

When mixed with common cast steel in quantities ranging from 11 to 131/2 per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time.. * At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 Ib. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13.5 per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 51/2 in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 51/2 in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an important consideration if the casting is to be a moving part in a machine. At the same time, the thickness of 51/2 in. is sufficient to permit the use of manganese steel for the heaviest classes of machinery.

Jan 1, 1916

By Y. A. Chang

Heat content values of tantalum monocarbide and tungsten monocarbide have been determined from 325" to 985°K by means of a drop-type diphenyl ether calorinzeter. Based on the values obtained in the present study and those available in the literature, best values lected and computed from 298. 15°K to temperatures close to their respectiue melting points. At temperatures higher than 1700°Kfor TaC and 27000 K for WC, values of Cp and related thermodynamic quantities were extrapolated based on the two Debye parameters: one corresponds to the metal sublattice and the other to the carbon sublattice. The contrzbutzon In the total specific heat due to lattice dilation was evaluated using the Nernst-Lindemann relalionship. The calculated values of Cp were in good agreement with the In view of their refractoriness, tantalum monocar-bide (TaC) and tungsten monocarbide (WC) are of con- experimentally determined ualues. Furthermore, the calculated values of the absolute entropies at 298.15"K were 5.03 and 4.15 in comparison to the experimental values of 5.05 and 4.15, all expressed in the unit of cal per degg-atom. Using the same Debye parameters, values of the linear coefficients of ther mal expansion for TaC and WC were calculated from absolute zero to their respective melting points using the Grüneisen equation. The calculated values are in excellent agreement with the experimental values available in the literature. Finally, the values of the bulk modulus of TaC from room tenzperature to temperature near its melting Point were also calculated using the equation recently derived by Anderson. No cot~ipari-son between the calculated and experimental values can be made due to lack of experimental data. siderable practical interest. In order to completely define these materials, it is necessary to know their thermal properties as a function of temperature. Tantalum rnonocarbide having a NaCl structure (B-1 type) melts congruently at 4250PK,1 while tungsten monoearbide with a simple hexagonal structure (Bh type) melts per itectically at 3049°K into melt and graphite.2 In the present study, the heat content values (from which

Jan 1, 1968

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By P. Hanniala, S. Harkki, B. Andersson

"The Outokumpu Flash Smelting Process was put into commercial operation in 1949. The original process was based on the use of preheated air. The adoption of oxygen enrichment of the flash smelting process air in 1971 was a crucial improvement, especially for smelter capacity. Oxygen use according to the Outokumpu method means selection of the most suitable oxygen content for the process air on the basis of the concentrate composition, capacity and matte grade. The furnace is not bound to only one fixed degree of process air oxygen enrichment; the oxygen content may vary from 21% to 100%.The degree of oxygen enrichment and the matte grade are the most important process parameters in reducing the operating costs of the whole system, including smelting, converting and acid production. Raising the matte grade allows more efficient use of the reaction heat in the smelting stage. Sulphur is recovered in a high-strength, constant-flow gas stream. The blowing time in the converters is reduced considerably.Oxygen enrichment and high matte grade improve the energy efficiency of the plant complex as long as the surplus heat from the system is not wasted. When the operating costs and investment expenditure of the total plant complex are taken into account, a reasonably high degree of oxygen enrichment (35-80°/0) is the best alternative in practice. Existing operating smelters have achieved single-stream thoughputs of over one million t/yr of concentrates.HistoryLocal capital and operating costs as well as lower energy consumption per unit of metal produced are now the crucial factors in determining the choice of process. In the late I940s, the same reasons prompted Outokumpu to develop the original flash smelting process in Finland. Between 1900 and 1940, very few technical changes in pyrometallurgical copper production took place. However, the commercial use of the flash smelting technique began a new era in metal extraction from sulphide concentrates. The characteristic feature of the method is that the concentrate is smelted in suspension: this offers the most favourable conditions for heat and mass transfer, and thus high reaction velocities. Outokumpu was the first to exploit the known advantages of flash smelting in a commercial installation at Harjavalta in 1949."

Jan 1, 1982

THE slag performs two useful functions. in open-hearth steel-making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SO2, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (SiO2 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1951

THE slag performs two useful functions in open-hearth steel- making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) Si02, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (Si02 and P205). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined; and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1964

By E N. Sajin

The final arsenic bearing waste products at the majority of metallurgical and chemical enterprises are cakes in which arsenic is present in the form of calcium arsenate. Burial of cakes demands construction of special burial sites and does not guarantee reliable protection from arsenic penetration into the ground and surface waters. Under laboratory conditions we developed technology for processing calcium arsenate cakes with obtaining low toxic products suitable for long-term storage, meeting environmental requirements. The investigations have shown that thermal processing of briquetted mixtures of cakes containing 15 - 20 per cent weight of pyrite under the temperature of 873 - 923¦K during 45 - 60 minutes gives briquettes sufficiently hard for transportation and long-term storage. Arsenic, under high sulphidisation temperature is bonded into low solubility non-volatile iron sulphide bearing compounds having chemical properties similar to the natural arsenic compounds. Solubility of the obtained products in neutral, acid and alkaline media was investigated during long period of time (three to 12 months). It was determined that arsenic content in the solutions did not exceed the norms for cultural and welfare basins and fish-ponds.

Jan 1, 2002

Carbon-concentration Meter The latest of these, the ultrasound-based carbon concentration meter, was developed by Mintek with original sponsorship by the Chamber of Mines Research Organization, and is now being manufactured and marketed worldwide by Debex Electronics in Johannesburg. Testing of detonators* The Chief Mining Engineer has asked the South African Bureau of Standards to monitor locally manufactured, as well as imported, detonators. This could ensure greater safety in fiery mines.

Jan 1, 1990

Guide Io Ihe Preparailon Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council.

Jan 1, 1975