Search Documents

By William Priestley

IN THE manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and elastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungsten, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured-by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. DESIGN OF GUN FORGINGS In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun are made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The elastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge.

Jan 12, 1921

By J. H. Maysilles

The Bureau of Mines is conducting research on various technologies to recover alumina from domestic resources for feedstock to existing aluminum smelting capacity as a means to reduce dependence on imported bauxite, which represents 93 pct of U.S. aluminum requirements. One of the more promising technologies being investigated is the hydrochloric acid leaching of kaolinitic clay. In the hydrochloric acid leaching technology, alumina is recovered from iron-free aluminum chloride leach liquor and separated from impurity elements by sparging the liquor with HC1 gas to crystallize aluminum chloride hexahydrate (ACH). A large-scale crystallizer with a 336-gallon usable volume was constructed and operated to obtain engineering and design data for potential scale up and to demonstrate the ability of the technology to produce specification grade alumina. Test campaigns involving about 1,400 hours of operation were completed. ACH meeting all chemical purity requirements could not be produced by a single crystallization, but was produced by recrystallizing the product from the calcined kaolin clay leach liquor. Product crystals with a size distribution of more than 80 pct plus 100 mesh and 65 pct plus 65 mesh were made at a rate of 10 pounds of ACH/(hr)(ft3). The zirconium tube heat exchanger used to maintain constant process temperature operated with an over-all heat transfer coefficient of 420 to 500 BTU/(hr)(ft2)(°F).

Jan 1, 1981

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

"There seems to be some confusion between the terms carbon black and lamp black, although in American lampblack is generally understood to be a soot formed by the smudge process. In this process oil, coal tar, resin or some solid, or carbonaceous substance is burned in an insufficient quantity of air, while on the other hand carbon black is a product resulting from the incomplete combustion of gas and is deposited by actual contact of flame upon a metallic surface.The various carbons, such as gas retort coke, oil retort coke, graphite, carbon black, lampblack, vine black, wood-pulp,black, willow charcoal, and blacks made from refuse material such as leather have different characteristics as to flocculence strength of color, and physical structure. These blacks are made by one of the following methods:(1) Formation by direct contact of a flame upon a depositing surface.(2) Production by combustion of an oil, tar, etc., in an inadequate supply of air; the soot is allowed to slowly settle out on the floors and the walls of the collecting chambers.(3) Carbonization of solids and subsequent reduction to a state of small subdivision.(4) Production by heating carbonaceous vapors or gases to a decomposition temperature by external heating with or without air in the forming chamber. This is usually referred to as cracking or thermal decomposition."

Mar 1, 1920

By Robert A. Westin

Polychlorinated biphenyls (PCBs) are a group of chlorinated chemicals that were used in many different fire resistant hydraulic fluids, heat transfer fluids, and in electrical equipment as dielectric liquids. PCBs were manufactured primarily by Monsanto Chemical Company under the tradename Aroclor, and were used by many different electrical equipment manufacturers. PCBs are noted chiefly for their extreme chemical inertness. This resulted in exceptional fire resistance and long life in applications involving exposure to high temperatures and intense electrical fields. This combination of properties resulted in PCBs being widely used in electrical equipment used in mines, including transformers, capacitors, and some electric motors. PCBs were also used as working fluids in some heat transfer and hydraulic sys terns. The same chemical resistance that gave PCBs long life in industrial applications give PCBs essantially eternal life when they are released into the environment. PCBs are not highly toxic in the sense that exposure does not cause immediate health problems. However, PCBs accumulate in the human body and neither degrade nor are eliminated from the body, and long-term exposure to PCBs can result in changes in liver function which may increase susceptibility to the carcinogenic effects of other chemicals. PCBs also accumulate in the food chain; the concentration of PCBs in fresh water fish may be several hundred thousand times as high as in the water the fish are taken from.

Jan 1, 1981

By A. Demirci, A. Keçeciler, Y. S. Durutürk

"This paper deals with the results of the variation of thermal conductivity of rocks with pressure on a laboratory scale. For this purpose, the authors have added a pressure-supplying unit to the apparatus developed by Mousset-Jones and McPherson (1986), Önder (1995), Ashworth and Ashworth (1979), and Innaurato and Occella (1989) in order to measure the thermal conductivity under pressure. The values obtained from the tests performed by this new apparatus have been stated using a regression analysis and the related graphs have been drawn. Results have shown that the thermal conductivity of rock varies digressively with pressure. The same results have been obtained in different rocks types. IntroductionOne of the most important tasks of mining engineers is that of establishing, maintaining and sustaining safe and healthy working conditions in underground mines.Heat can have a profound effect on safe and healthy working conditions and is one of the main problems in deep underground mines. In this regard, the temperature of the air passing through the mine openings increases steadily and causes a decrease in the efficiency of workers due to the unwanted physical effects to human bodies in the working area. At the same time, the hot and humid environment resulting from heat and temperature rise causes some important occupational diseases and increases the accident risks in the related openings."

Jan 1, 2002

By Z. J. Hladysz

The Hladysz Rock Tester was developed at the South Dakota School of Mines as a portable rock strength tester. The hand held device is placed against a rock surface and struck by a hammer. The impacted force causes a steel ball in the device nose piece to indent the rock and simultaneously indent a standard steel bar also contained in the nose piece. By comparing the two indented diameters the compressive strength of the rock can be calculated using laboratory determined correlation coefficients.

Jan 1, 1984

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

By B Wentzinger, Y Keulemans

This paper presents the results of a field study designed to assess the impact of vane rotation speed on the estimated undrained strength for two Australian bauxite tailings storage facilities. The vane test results are assessed against cone penetration and dissipation tests results to identify if partial drainage may be an issue. An innovative tool capable of measuring pore pressures during vane shear testing, the Piezovane™, is introduced as an improvement over the standard field vane to assess drainage conditions in real-time.

Jul 1, 2021

By J. Harrison Daniel

More stringent dust standards, because of quartz in coal, have become a major compliance problem for the coal industry. Reducing quartz levels has become the major focus of the Bureau of Mines dust control research program. Results to date have identified hath the sources of quartz and prospective control technology. Control techniques are being developed for both room-and-pillar and longwall mining underground operations. Techniques include changes in face ventilation, mining cycle modifications, and better roof bolting dust control.

Jan 1, 1985

By G. Heymann, T. Grobler

Many tailings storage facilities in the Rustenburg region of South Africa’s North-West Province are founded on reworked residual norite derived from the weathering of the Bushveld Igneous Complex. With the implementation of the Global Industry Standard on Tailings Management, increased emphasis is placed on robust material characterisation, but laboratory testing is challenging. The results of Oedometer and undrained triaxial shear testing support a nonlinear failure envelope for effective stresses below the yield stress, transitioning to linear behaviour at higher stresses.

Apr 8, 2026

By H. R. Gardner

The heat treatmmt of plutonium was studied using the Jominy end-quenching technique commonly used for determining the hardenability of steel. Plutonium specimens were end-guenched from temperatures in each of the ß, y, d, d') and E phases. One series of specimens with a low-iron content, 165 pprn Fe, and another gvoup with a high-iron content, 678 pprn Fe, were used in order to study the effect of a Pu-Pu,Fe eutectic network on the hardness and micro-structure. Hardness traverses indicated no significant variations in hardness with either cooling rate or quench temperature. Metallographic studies indicated major effects on microstructure. Grain size was found to vary markedly with quenching temperature and cooling rate. It was determined that the Pu-PueFe eutectic network could be modified extensively by heat treatment, including spheroi -dization in the y phase and 6 phase below 413°C. An unidentified spheroidal inclusion was observed to go into solution in the delta and higher temperature phases. 1 HE element plutonium is unique among metals in that it has six allotropic forms in the solid state.' These have been designated' as the a, ß, y, d, d', and phases. The respective phase transformations occur at approximate temperatures of 122", 210°, 319°, 450°, and 480°C with a melting point at 640°C. With this number of phase transformations it becomes pertinent to consider the effect of heat treatment and cooling rate in the various phases on the microstructure and hardness of plutonium. To determine; the effect of a wide range of cooling rates, the Jominy end-quenching technique was applied to cylindrical plutonium specimens. In addition, since the presence of iron in amounts greater than 500 pprn is common in plutonium and results in a network of the Pu-Pu6Fe eutectic, it was decided to study heat treatment effects on two bomb reduced plutonium buttons with different iron contents. A low iron button containing 165 ppm Fe and a high iron button containing 678 ppm Fe were selected for this comparison. EXPERIMENTAL PROCEDURE Experimental Material. The cylindrical bars for Jominy quenching were cast from button stock in vacuo in MgO coated graphite molds. Metal pouring temperature was approximately 950°C and the molds were preheated to 300°C. The castings were machined to 0.5 in. diam. by 2.5 in. long cylinders. Chemical analysis and density data for the two groups of Jominy specimens containing different iron contents are presented in Table I. Except for iron, heats 19-12-1 and 20-2-1 are comparable within the limits of analytical accuracy. Representative specimens from the low-iron and high-iron bars were taken for metallographic examination. The low iron specimen was found to have extensive microcracking, Fig. 1. In addition, numerous unidentified spheroidal inclusions were present, Fig. 17. The average grain size of the low-iron plutonium is 0.068 mm, Fig. 4. In the high-iron plutonium, a Pu-Pu6Fe eutectic network is prominent, Fig. 7. The average size of the network is 0.100 mm. Unidentified spheroidal inclusions were also common in the high-iron plutonium. The average grain size of the high-iron plutonium is 0.036 mm. Experimental Technique. A Jominy end-quenching fixture was fabricated for glove box use. A 2.5 in. water height was used with an orifice of 0.250 in. ID. The orifice to specimen distance was maintained at 0.5 in. Annealing temperatures of 160°, 265°, 400°, 465°, and 535°c were chosen for the study of the effect of quenching from ß, y, d, d', and e phases on microstructure and hardness. During quenching, cooling curves were obtained from the Jominy specimens at distances from the quenched end of 1/16, 1/8, 3/8, 3/4, 1-1/4, and 2 in. Cooling rate calculations were made from the cooling curves for temperature intervals of 100° to 110° 160" to 170°, 330" to 340°, 420° to 430°, and 490° to 500°c. These temperature intervals were chosen

Jan 1, 1962

By Michael Hoch, Walter C. Wyder

The isothermul section of the Nb-Ti-Zr-O system at 1500°C was investigated using X-ray dzffraction and metallographic techniques. UP to 66.7 at. pct 0, the system contains nine four-phase regions. Tsopleths at 10, 20, 30, 40, 50, and 55 at. pct 0 weye constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of niobium, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct. O., PREVIOUS INVESTIGATIONS The Ti-Zr-O system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by anssen2 and Levin, McMurdie, and Ha11. Elliott4 has determined the Nb-O system by metallographic and X-ray diffraction techniques. He shows the existence of three oxides, namely NbO, NbO2, and Nb2O5. At 1500°C the solubility of oxygen in niobium is about 4 at. pct. No solid solubility region is shown for either NbO or NbO2. EQUIPMENT The same equipment as that for the study of the Ti-Zr-O system was used. The X-ray diffraction patterns were analyzed with the help of the ASTM card set5 and NBS circulars.6 MATERIALS The niobium powder (99 pct pure), the titanium powder (99.6 pct pure), the niobium pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmount Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., N.Y. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure," the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE Samples of the desired compositions were made up, in mole pct, from the materials listed above. In some cases the intermediate binary compounds, such as NbO and TiZrO4 were prepared beforehand and used in the preparation of the samples. This technique enabled equilibrium to be reached from two sides. The components of each sample were mechanically mixed in a mortar and pestle and pressed into 3/16-in. diam pellets. The pressures used in compacting were of the order of 50 to 100 x 103 psi. Sintering was accomplished by heating the samples in a tungsten crucible (3/4-in. high, %-in. diam, 1/8-in. wall, lid with XB-in. hole). The pellets were separated from each other and from the crucible by means of small spiral coils of tungsten wire placed between the stacked pellets and on the bottom of the crucible. The sintering time was from 4 to 12 hr at 1500°C under a vacuum of 6 x 101-5 to 1 x 10-6 mm of Hg. All samples were reground after the first or second heating repressed, and reheated. In most cases: equilibrium was obtained after the first heating, as the X-ray diffraction pictures after each heating remained unchanged. Quenching of the samples from 1500°C was at first only possible by allowing the crucible and its contents to lose heat by radiation. The temperature dropped from 1500° to 900°c in approximately 1 1/2 min, which was considered adequate when compared to the times used by other investigators to reach equilibrium in the temperature range of 1000°c and lower. Later, a new technique for faster quenching of the samples was cleveloped. This technique involved the removal of the samples from the crucible, whereupon they were quenched by coming in contact with the water-cooled copper base of the furnace. This manipulation was performed without breaking the vacuum. The sample pellets were placed on a tungsten wire rack inside the crucible. The wire rack passed through the hole in the crucible lid, where it was connected to a small nonmagnetic chain. The chain was fed to the side of the furnace by means of a brass rack which fitted between the body and lid of the furnace. Suspended at the end of the chain, near the furnace wall, were three magnetic washers. With the use of a strong

Jan 1, 1962

By G. H. Kessler

ALTHOUGH considerable attention has been devoted to reaction mechanisms and equilibria of a number of endothermic reactions through which metals or their refractory compounds can be formed upon heated surfaces, only a comparatively small amount of work has been done to develop rate information for these systems. The interestin and very worthwhile work of Holden and Kopelman, Runnalls and Pidgeon,Dijring and Moliere, and Herrick and ICrieble4 is to be noted; however, their work was done under very specific conditions and the rate information which they have developed is not applicable to many systems which have been studied experimentally. That a more generalized approach is needed is shown by the diversity of these systems and of the experimental conditions which they require. These include the preparation of titanium, zirconium, tungsten, molybdenum, chromium, co-lumbium, aluminum, and silicon by decomposition or disproportionation of their halides, in some instances through hydrogen reduction; the preparation of nickel and iron by decomposition of their car-bonyls; and the preparation of copper by decomposition of the acetylacetonate. They may be carried out at temperatures ranging from 100" to over 2000°C and at pressures of from less than one mm Hg to superatmospheric. The physical mechanism of the overall process can be broken down into several steps, any one of which may be rate-determining; and the rate associated with each of these basic physical processes can be predicted. Consequently, by proper application of the present technology of rate processes, it is possible to arrive at a rate of metal deposition in the system of interest and to reach an understanding of the influence of' each major variable upon the deposition rate. It is the purpose of this paper to illustrate how this can be done and to present experimental results for a specific system for comparison with theory. The overall process of deposition of metal upon a heated surface which is immersed in vapors of a compound of the metal can be broken down into the following steps: 1) Transport of the reactant vapors to the surface. 2) Decomposition of the reactant in the immediate vicinity of the surface to a) establish chemical equilibrium if reaction rates are high; or to b) establish a dynamic equilibrium in accordance with the several reaction rates. 3) Diffusion of reaction products away from the vicinity of the surface, with or without simultaneous recombinations to form still other products. The overall process is said to be diffusion controlled if Step 1, or the equivalent Step 3, is slow; it is reaction-rate controlled if Step 2b is slow. When experimental evidence shows the reaction rate to be controlling, the well-known theories of Eyring' and others can be used as a basis for correlating and extrapolating the experimental data. Although these theories give only approximate estimates of reaction rates, they are of considerably greater value in correlating experimental data. Most deposition systems operate at surface temperatures sufficiently high that reaction rates near the surface are very high. Mass-transport rates then become controlling; and it is this regime of diffusion controlled rates which is most often of concern and Which will be considered here. When the system pressure is very low, i.e., in the micron range, then the transport processes are those of molecular movement, and the results of kinetic theory can be applied to specify a rate of arrival of reactant molecules at the heated surface. If the condensation coefficient can be estimated, then the deposition rate will be given by the product (rate of arrival) x (condensation coefficient), Conversely, experimental data can be used to determine a condensation coefficient, as was done by Holden and Kopelman' for the decomposition of zirconium tetraiodide upon a heated molybdenum surface, who found the coefficient for zirconium on molybdenum to be 1.0 at temperatures of 1382°C and above. In this pressure range, the geometry of the system. and in particular the distance between the source of reactant molecules and the heated surface, can exert a considerable effect upon the deposition rate;

Jan 1, 1961

By R. H. Edsal, G. Horvay

The transient one-dimensional heat-conduction equation is solved for two semi-infinite media, at different initial temperatures, brought into (poor) thermal contact. It is shown that the two interface temperatures gradually approach the well-known, instantaneously assumed, common interface temperature of the case of zero contact resistance. The present analysis, with slight modifications, may be used in fair approximation also for the class of problems involving a change of phase. One particular application of the boundary value problem solved in this paper concerns the determination of the temerature distribution in metal castings and molds.P This problem has been treated extensively by analytical methods (see e.g., the literature listed in Refs. 1 to 4) by electrical analogs (see e.g., Refs. 11 to 14) and also by experimental methods (see the literature listed in Refs. 4, 5), but prior to the work of Pellini and Ruddle the experimental results were rather unreliable. Immediate motivation for the work described in this paper was to better understand the results of Pellini,' which are typified by the curves of Fig. 1. Pellini cast 20-in. high, 7-in. sq steel ingots into cast-iron molds of various thicknesses. He measured the temperatures at mid-height, at a number of stations in the casting and the mold, and obtained the cooling curves shown in Fig. 1. The most conspicuous thing about Fig. 1 is the large temperature discontinuity at the interface between casting and mold, due presumably to the shrinking away of the casting from the wall and the attendant creation of an airgap, as the casting cools. Such a contact resistance slows down the anticipated freezing rate; an analytical prediction of this is of much interest in foundry practice. The determination of the effect of contact resistance in the presence of a change of phase will be dealt with, by an approximate method, in a separate paper.' In the present paper the much simpler problem is considered in which there is contact resistance but no change of phase. This problem frequently arises in the analysis of aircraft structures.+ It can initial temperature, and may be regarded as semi-infinite. We suppose the thermal properties in the two media to be time, temperature, and space independent; there are no sources or sinks within the media. In Fig. 2(a) we illustrate, schematically, the case of no contact resistance. The semi-infinite media "0" and "2:' initially at temperatures 8 (- m) and 8(+ -), respectively, are brought into contact at time t =0. A common interface temperature 8,i = is instantaneously established, and thereafter remains constant. Temperature curves are drawn for three instants of time. When there is contact resistance between the two media, the temperature equalization occurs as sketched in Fig. 2(b). Fig. 2(c) illustrates a temperature curve, using the dimension-less notation Barber-Weiner-Boley6 have stated the equations [23a, b] given below, which govern the heat transfer in the two media, and solved them for a rather complicated special case. In their example both media "O" and "2" are finite, are insulated at their far ends, and there is steady heat input into medium 2. In Eq. [27] we give the general solution of the most important special case, where the two media are semi-infinite and there are no sources or sinks. In this case the results may be stated in simple closed form. In Fig. 3, to be discussed in the next section, we illustrate the variation of the interface temperature when steel at 2760" is brought into contact with iron at 100". This example, if we disregard the effect of the heat of fusion, is comparable to Pellini's experimental results, Fig. 1. (Unfortunately, however, experimental determination of the interface temperatures was difficult to carry out, and hence Fig. 1 is not very accurate near the interface.) In Figs. 4 and 5 of the following section, we similarly compare Pellini's sandcasting tests with analytical results for the case where steel at 2760" is brought into contact with sand at 100". It will be pointed out that, insofar as the interface temperatures are concerned, heat of fusion has a minor effect, and so the present approximation, with small modifications, may be

Jan 1, 1961

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,&apos;-!&apos; other investigators have encountered difficulty with the method."&apos;. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.&apos; The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28&apos;, which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.&apos; On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.&apos; &apos; The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,&apos; conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968