Search Documents

By F. B. Foley

With the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal1 published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-of theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1/14-in (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. with time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the great decrease in breakage by the use of smaller diameter drills. The figures are given as so many drills sharpened, but there is no way of determining the percentage of

Jan 1, 1922

By Francis Foley

WITH the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges' the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal' published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-f theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1 ¼ -in. (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. With time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the "enormous decrease in breakage by the use of smaller diameter drills." The figures are given as so many "drills sharpened," but there is no way of determining the percentage of

Jan 6, 1921

By W. J. Taylor

SOME eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur were naturally in the lime-kiln line, with solid fuel mixed with the ore, in the same way as common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known fact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature. This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseous fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced – 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By W. J. Taylor

Some eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur mere naturally in the limekiln line, with solid fuel mixed with the ore, in the same way = common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known Pact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature..• This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseoua fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced— 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By L. Zwell, H. A. Wriedt

In describing their procedure for measuring the lattice parameters of solid solutions, Abrahamson and Lopata report (p. 77) the final heat treatment of their alloy specimens as "700°C for 100 hr, followed by a furnace cool". The isothermal part of this treatment may be expected to precipitate solute in excess of the stable a solid-solution limit at 700°C; the subsequent slow cooling is likely to reduce the dissolved solute still further. Fig. 1 (upper) presents the data for titanium alloys so he;rt-treated and shows the lattice parameters of solid solutions containing up to 3.5 at. pct Ti; Fig. 17 (lower) shows 2 at. pct Ti as the solubility limit in a iron at 700°C. Figs. 1 and 17 are thus incompatible. The paper contains comparable incon~patibilities for zirconium alloys, for niobium alloys, and for tantalum alloys. The final heat treatment at 700°C may also be responsible for the anomalous "knee" in the lattice-parameter data for nickel alloys, Fig. 3. The "knee" composition is located near the 700°C limit of the stable a solid-solution field;37 alloys of the experimental composition range with more nickel than the "knee" composition are two-phase at 700 C and prolonged heat treatment of them at 700°C would tend to produce inhomogeneity rather than homogeneity. In Figs. 4 and 7, the composition ranges of the zirconium, hafnium, and niobium alloys examined terminate at alloy concentrations of 0.1 to 0.2 at. pct. These metals form very stable oxides and their partial removal from solid solution in iron by impurity oxygen may be expected. We believe that the authors should have reported the procedure by which they distinguished the amounts of alloying elements in solution and in oxide. The diagrams pertaining to copper in Figs. 3 and 18 (lower) are almost certainly incorrect. Three recent investigations of this system38-40 all substantially agree on the solubility of copper in a iron, finding it to be much larger than that reported by Abrahamson and Lopata. The change of the lattice parameter with composition reported by Abrahamson and Lopata is too large by a factor of three to five, as seen by comparison with the findings of other investigators.41738 Moreover, the authors violate, in Fig. 18, the accepted Fe-Cu constitution diagram37 by ignoring the eutectoid at about 850°C.

Jan 1, 1967

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By R. E. H. Pomeroy

The statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Mc Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. % in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5" B., flashing in open test at 199" F. The oil is heated to about 200" F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 Ib. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-08. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and " dog houses" to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent. The draft at the firing end of the furnace is 0.18 in. of water. At the throat or in the uptake above the "verb" the draft is about 1 in.

Jan 1, 1915

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe&apos;s Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941

By A. G. Buyers, J. Chilton, W. E. McKee

STUDIES in the high-temperature separations chemistry of thorium-uranium fuels are complicated by the corrosive nature of these molten metal systems at 1700°C. Separations research pointed toward the removal of fission products from irradiated alloys has included a frozen salt-bed technique which minimizes container reaction with molten metal. The procedure consists of high-frequency induction melting of the metal sample which is supported by a vertical column of unmelted salt. The molten alloy melts its immediate salt environment and as it slowly falls down through the column, many of the fission-product poisons are transferred into the fused salt environment. The molten salt-metal zone is encompassed at all times by unmelted salt, preventing container contact. EXPERIMENTAL Experimental methods were separated into three parts: salt-bed preparation, melting, and analytical evaluation. A) Bed Preparation—The procedure for casting calcium-fluoride briquettes was to compress the powdered salt at 5,000 to 10,000 psi and place this compact in a graphite crucible. This assembly was inserted into a vacuum system and surrounded by an alumina crucible as well as molybdenum, tantalum, or stainless-steel foil thermal-radiation shields. The pressure was reduced and the crucible heated under vacuum to about 800°C with the fore pump operating. Argon was then admitted to about 0.8 atm and heating continued until the CaF2 had melted 5 min at the melting point seemed satisfactory). Apparatus used included a 1-in. graphite crucible with 1/8-in. walls, 1-in. ID in a 2-in. induction coil, and a 6-kw Ajax high-frequency converter. B) Melting—Calcium-fluoride briquettes, 1 in. in diam and 1/2 to 1 in. thick, were prepared and vertically stacked to obtain the desired column length. An irradiated alloy sample (nut = 10") was placed on top of the salt column and the assembly was connected to the vacuum system. After evacuation of 5 to 10 , purified argon was admitted and the system flushed twice. The final argon pressure was about 0.8 atm. The sample was heated by induction at a power of about 6.5 kw. It then melted its way down through the salt and freely dropped into a small alumina crucible. The molten metal is followed during its downward course by the induction coil which is mounted upon a power-driven machine-threaded shaft. Experimental conditions used in the foregoing work

Jan 1, 1960

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. [t] About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5.800,000 bbl. of cement. Following are some of the cement require¬ments of the Shasta Dam specifications: [PER CEN&apos;I Chemical composition: Loss in ignition2.25 Insoluble residue0.75 S032.25 M905.00 Uncombined lime in clinker (CaO)T.25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 35 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 6,5 Tricalcium aluminate (3CaO.Al203)Not more than 7 Tetracalcium aluminoferrite (4CaO.A1203.Fe203) Not more than 20 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following: [ ]

Jan 1, 1941

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe&apos;s Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.&apos;&apos; Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By T. R. Ingraham

The thermal decomposition of Nickel (II) sulfate was examined by determining the total pressure of SO3, SO2, and O2 developed over a sample when it was heated in an evacuated system fitted with a Pyrex-bellows mercury manometer. The equilibrium pressures were combined with previously published data on the oxide and sulfide systems to establish a predominance volume diagranz for the Ni-S-O system over the normal range of roasting temperature and gas composition used in the treatment of nickel minerals. The protective coating of NiSO4 which forms on the oxide during roasting, and which causes the sulfation reaction to almost cease, may be disengaged readily by temperature cycling. When nickel sulfide is roasted in air, either nickel sulfate or nickel oxide may be formed by altering the experimental conditions. Because of the differing stabilities of various metal sulfates and oxides, possibilities exist for separating some of the constituents of mineral mixtures by the technique of selective sulfation and oxidation roasting. The experimental information required to make reasonable predictions of the possibilities of this technique is incomplete and, in some cases, in conflict. As part of a general program of providing some of the required information, a study EXPERIMENTAL Materials, Apparatus, and Procedure. Fisher certified reagent-grade nickel sulfate hexahydrate was used in the source material for both nickel sulfate and nickel oxide. The manufacturer&apos;s analysis indicated: 0.001 pct Fe, 0.005 pct Cu, 0.003 pct Co, 0.001 pct C1, other 0.15 pct. The material was dehydrated, before use, by heating at 420°C for 5 hr. The oxide was prepared by roasting the sulfate in an open tray in a muffle furnace for 10 hr at950°C. Preliminary experiments which were made by thermogravimetric analysis and X-ray diffraction analysis established that only one crystal form of nickel oxide and one of nickel sulfate were involved in the equilibrium shown in Eq. [I]. The apparatus used in the experiments was described previously.1,3 The main feature is a corrosion-resistant, flexible Pyrex bellows which is used to protect the mercury in a u-tube manometer. Before a run was begun, the apparatus was washed thoroughly with hot hydrochloric acid and water and dried by heating under vacuum. The mixed sulfate -oxide sample was contained in a platinum bat rest-

Jan 1, 1967

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.&apos;&apos; Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942