Search Documents

By W. P. Yana, J. B. Littlefield

"INTRODUCTION AND OBJECT OF EXPERIMENTAn explosion in and rupture of a gas-tight switch box on an electric loader in a mine located near Pittsburgh indicated that the cause was an internally generated inflammable gas-air mixture. This led to the suspicion that moisture condensation or ""other unusual conditions might have caused a spark or are across the surface of the material and that the heat may have created a carbonized path across the synthetic plastic base which would then conduct a large current with the generation of considerable heat and thermal decomposition of the base materials base in the box which exploded gave every indication that this series of events had taken place, and accordingly it was desired to determine what explosive gases such a decomposition of these insulating materials would produce.ACKNOWNLEDGMENTSThe desirability of making this investigation was suggested to the authors by L. O. Ilsley, supervising engineer, electrical section, Bureau of Mines, to whom the occurrence of an explosion in a switch box had been reported. The writers also acknowledge with thanks the assistance of L. B. Berger, chief scientific aide, health laboratory section, Bureau of Mines, in checking the calculations in the tables. DESCRIPTION OF MATERIAL INVESTIGATEDThe ten materials used in the tests, identified by letters A to J inclusive, are described in a succeeding list of materials. All the materials except I had a phenolic odor, especially when freshly cut."

Dec 1, 1932

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924

By Heinrich Möller

The electro-oxidation of 0.1 M ethylene glycol at gold, platinum and gold-platinum alloy electrodes in different heat treatment conditions has been studied in 0.5 M NaOH, at room temperature. Poisoning of all the electrodes occurs. However, the alloy electrodes poison at a faster rate than the pure gold and platinum electrodes. This indicates that the initially higher activity of these electrodes cannot be the result of decreased poisoning through a "third-body" effect.

Oct 1, 2003

By Walter G. Perkins

As this particular product holds a place by itself, it seems desirable to give a paper dealing especially with it as a corollary to my paper entitled " The Litharge Process of Assaying Copper-Bearing Ores and Products, and the Method of Calculating Charges."* The process is first to convert the metallic copper into matte by the addition of sulphur, allowing the two elements to combine at the bottom of the crucible when heat is applied. The

Jan 1, 1903

By James G. Stuart

For precise control and timing of a blast, people use electric detonators. Most of these contain a fine metal “bridgewire,” that heats to the required burning temperature when electric current passes through it. Users should be careful. Stray voltage can fire these detonators. Some designs are particularly susceptible to electrostatic-discharge (ESD). We will discuss some of the accidents we have encountered in our forensic work. We will recommend specific safe procedures for handling and firing these devices.

Jan 1, 2005

By W. W. Koczkodaj, J. Partyka

Beat exchange in an open air-water system is considered. The system incorporates a vertical cooling tower, and a horizontal multi-stage spray chamber with unlimited number of stages. Mixing of two streams of both water and air is permitted. A spread-sheet implementation estimates temperatures of outgoing water and air for given mass flow of water and air, factor of merit for heat exchangers, barometric pressure, wet- and dry-bulb temperatures, and the temperature of incoming water.

Jan 1, 1987

By Kwang K. Koh, Nicholas C. Nahas, Richard C. Neavel

Sodium, a relatively abundant element in Illinois coal, is reported to cause fouling of utility boiler heat exchange surfaces. Distilled water extraction of 22 Illinois coal samples resulted in average removal of more than 50% of their included sodium. Chlorine was the dominant anion. Extraction rate conformed to Fick's law of diffusion. Extraction with hot water increased both the rate and maximum amount removed. A commercial-scale countercurrent staged process can be envisioned as technically feasible.

Jan 1, 1978

By Alfred E. Hunt

Professor EGGERTZ first published a method based upon the fact that, when steel is dissolved in dilute nitric acid, and heated until the separated flocculent carbonaceous matter goes into the solution, the liquid assomed a brown color proportionate in intensity to the amount of the combined carbon in the steel. This method has been so variously modified that at present but few chemists use exactly the same procedure. It is the object of this paper to present

Jan 1, 1884

By G. W. Land, A. F. Duzy

There have been some problems associated with hot coal, defined as oxidizing coal heating toward ignition temperature, in shipments from the US to overseas markets. This paper will provide, first, a brief review, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1986

By Fathi Habashi

New technology first introduced by Nippon Steel Corporation at Kitakyushu in Japan in 1976 now used at a number of plants in other countries, known as dry quenching of coke, uses nitrogen in a closed circuit to avoid environmental emissions. In addition, heat is recovered in the form of steam, from the red-hot coke. In steel plants oxygen is used extensively and therefore by-product nitrogen from air liquefaction can be effectively utilized in this way.

Jan 1, 2014

By Barnett LJ

The Kellogg slag fuming model is extended to apply to the Port Pirie plant which uses recuperative heating of secondary air. Exten- sive investigations of plant operations pro- vide parameters for use with the model, and verification that the resulting model provides simulation which is very close to actual plant performance. The model is used to_deter- mine optimum slag fuming operating conditions, and the results of several other investigations with the model are briefly described.

Jan 1, 1975

By L. K. Smith, E. M. de Kock, J. van der Walt

A unique and systematic approach for analysing alternative methods of ventilating and cooling large hot mines is presented. The important factors that have a bearing on ventilation and cooling requirements and practices, such as air flow through the mine, geographical distribution of heat loads, micro ventilation considerations etc., are dealt with. Analysis of these leads to the definitive ventilation and cooling strategies, air and water process design, detail specifications and design of associated plant and equipment.

Jan 1, 1982

By E. Morrice

High-purity lanthanum metal was prepared by electrolysis of La003 in a LaF3-LiF-BaF2 bath at 950° C. The requisite bath temperature for the deposition of molten metal was maintained by supplying the heat as current directly to the electrodes. A current efficiency of about 60 percent was obtained. The lanthanum nodules contained carbon and oxygen as major impurities. The total impurity content was from about 0.1 to 0.2 percent.

Jan 1, 1962

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By Jing Zhang, Chenguang Bai, Fusheng Pan

"The microstructure and hot deformation behaviour of an Er-modified Mg-Zn-Ai alloy were evaluated. The results showed that the addition of rare-earth Er changed the morphology of the quasi-continuous grain boundary networked eutectic compound to globular particles. Moreover, a self-strengthening effect was identified for the alloy, which determined its deformation behavior. After hot extrusion, the yield strength and elongation to failure of the Mg-Zn-AI-Re alloy at 200°C were increased by 105% and 120%, respectively, due to an emerged dynamic precipitation strengthening mechanism.IntroductionMagnesium alloys are attracting increasing attention for applications in automobile, electronic devices and hand tools for weight reduction and higher fuel efficiency, because of their lightweight and a high specific strength. However, application of Mg is still very limited. The largest applications are still those non load-bearing castings used at room temperature, such as box case, housing, and covering. One of the main reasons is the inadequate absolute strength both at room temperature and elevated temperatures (> 100°C) of the commercially used AZ, AM series alloys, due to the incoherent interface between the secondary phase y-Mg17AI12 and Mg matrix, as well as the low thermal-stability of the y phase [1]. Besides, the heat-resistant magnesium alloys which contain rare earth (Re) as the main alloying element are very expensive. The other reason is their poor deformability. The key solution is therefore to develop low-cost heat -resistant wrought alloys."

Jan 1, 2012

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927