Search Documents

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

By A. A. Jonke

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations and design studies are being carried out by various organizations under contract with the U. S. Environmental Protection Agency and the Dept. of Interior (Office of Coal Research). The AEC's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. This paper covers the principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process. The participants in the multi-organizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1974

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

By W. Ayvazoglou

A large number of organizations interested in the search for mineral deposits have adopted the magnetic method of geophysical prospecting, as it has proved to be the most simple, convenient, and rapid, and at the same time the least expensive in comparison with other methods. According to the last statistical data, about two millions square kilo¬ meters were explored in the United States by different geophysical methods. Ninety-six per cent of this area was prospected for oil and 4 per cent for minerals. Detailed exploration by means of the magnetometer has been carried out over about 85 per cent of this surface. The great advantages offered by this method resulted in the fact that the magnetometer was tried out in most places in which geophysical methods were applied. The main purpose of such e:rploration is to obtain the maximum knowledge valuable to the geologist; therefore good geological interpretation of the results of measurements is important. The possibility of drawing practical conclusions from a map representing the results of the study of the terrane depends greatly on the accuracy with which the measurements are made. The purpose of this article is to show the different sources of error by which the work of an operator may be affected and to discuss the means by which the carrying out of a magnetic survey may be improved.

Nov 1, 1931

By R. Gilman Brown

INTRODUCTION. MINES are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique geological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.' On the other hand, this output has been mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness-from 0.5 in. of "specimen rock" to 30 ft. of clay and quartz; distributed through a zone about 2,000" ft. in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a few miles from its western edge, marked here by Mono lake on the line of the Great Fault. The average elevation of the outcroppings of the veins may be taken at about 5,700 ft. The andesite projects from south to north in a great tongue, 12,000 ft. long and 5,000 ft. wide, reaching an extreme height at the northern end of perhaps 1,000 ft. above the adjoining small canyons. These separate it from the main mass of the foot-hill

Jul 1, 1907

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Thomas Fraser, M. G. Driessen

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation, and utilization of coal . The mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British Committee . Engineers from other allied countries cooperated in some of the investigations . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , deputy solid fuels administrator . The personnel of the mission consisted of H. F. Yancey , in charge , J. W. Buch , Thomas Fraser , L. L. Newman , and L. D. Schmidt , of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology ; H. J. Rose , vice president and director of research , Bituminous Coal Research, Inc .; and F. H. Reed , chief chemist , Illinois Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These and microfilms of supporting data obtained in the course of the investigations are on file at the Bureau of Mines , Washington , D. C. where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproductions of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of 10 dollars will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low-temperature carbonization processes ; metallurgical coke from weakly coking coals ; low- ash electrode carbon from coal ; new developments in the production of metallurgical coke and the utilization of gas and byproducts ; briquetting brown coal and bituminous coal without the use of binders ; recent engineering developments in gas turbines and steam generators , with special reference to use of coal ; German coal-fired heating and cooking stoves; and the commercial extraction of coal with solvents for production of synthetic liquid fuels or chemical products . Numerous reports on the activities of German synthetic - liquid -fuels plants and the plants for the production of synthesis gas from solid fuels are available in the same office as the Solid Fuels Reports . It is planned to publish in this series of Information Circulars the more important reports or combinations of reports prepared by the members of the Solid Fuels Mission . A similar series on synthetic - fuel activities is being prepared .

Nov 1, 1946

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By Frank T. Sisco

SHORTAGES of metals and minerals and substitution of less critical materials for those in which a virtual famine exists received detailed and frank discussion at a recent conference in Washington called by Robert E. McConnell, director of the Conservation Section, Office of Production Management. Representatives of the large engineering societies in the United States and O.P.M. department heads participated in the discussion. To open the session Mr. McConnell called upon Zay Jeffries, chairman of the O.P.M. Advisory Committee on Metal Conservation and Substitution, to summarize the present situation. Dr. Jeffries touched briefly on the status of metal shortages, which has already received considerable attention in the popular press, and said that much of the present difficulty was caused by the too-hasty substitution-without sufficient con¬sideration of the immediate conse¬quences-of metals having ordinarily a small yearly consumption, for those having a much larger annual consumption. As a result, all the alloying metals used in alloy-steel manufacture have become scarce, with the exception of molybdenum; further¬more, despite a reserve of 11,000 tons of molybdenum in this country and despite a normal consumption of only about 3500 tons and a prospective annual production rate of 21,000 tons by October, a shortage of molybdenum is possible before this war is over.

Jan 1, 1941

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Carlos Torres, Albert Cabrejo

For the last 20 years mine slopes have been monitored with slope stability radars. Since 2015 a group of dedicated geotechnical engineers dedicated to remotely monitor radars around the world have detected 2000+ slope failures of different characteristics. A statistical analysis of the information gathered of these failures have been made and the summarized results are presented with some degree of analysis appropriate for the vastness of the database. The analysis considers different types of commodities, countries, mining processes, rock types, and weather conditions.

Sep 29, 2023

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

The Atlanta Mine is located in east central Nevada, in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of the old mining town of Pioche. From this famous district, high-grade copper ore was mined and shipped to a smelter in Wales in the 1850s; an early day lead blast furnace was also in operation. The Standard Slag Company began operations in May 1975 on the well known Atlanta Mine, which was operated by Roy Hardy in the 1930s. The mill is currently processing 450 mtpd (500 stpd) of gold-silver bearing ore. Mining by open pit is in a brecciated zone occurring between limestone-dolomites on the foot wall and tertiary rhyolites on the hanging wall. The quartz breccia is considered among the most abrasive in the world - shovel teeth must be replaced every week. Stripping ratio is 3.9 to 1.0. Because of the hard abrasive ore, the crushing plant consists of four units: two jaw crushers in series, one Hydrocone, and one Gyradisc. Mine feed to the primary crusher is limited to 610 mm (24 in.) in size. The remaining crushers work in closed circuit with screens to produce a mill feed of 6 to 13 mm (0.25 and 0.50 in.). Hardness of the ore is demonstrated by the fact that the reversible liners of the primary jaw crusher had to be replaced in early 1978 after handling only 39,000 mt (44,000 st) at a cost of $0.095 per mt ($0.086 per st). Another example of the extreme abrasiveness of the breccia ore was the total cost per ton in 1977 for all wear parts in the comminution circuit, including screens and grinding media. This amounted to $2.84 per mt ($2.58 per st). The Atlanta grinding plant consists of three ball mills to grind the 7 mm (1 /4 in.) crushing plant product to 85 to 90% minus 150 microns (100 mesh). Feed rate to the primary Tricone mill is determined by maintaining a cyclone overflow at 28 to 38% solids, which controls the grind mentioned above. A mixture of 90 and 65 mm (3.5 and 2.5 in. ) balls are charged to this primary mill. Both the secondary mills are charged with 50 mm (2 in ) balls. Total ball consumption is 2 kg per mt (4 lb per st). All three ball mills use rubber liners. Primary mill cyclone underflows are fed to the secondary mills close circuited with the same cyclones.

Jan 1, 1981

By V. H. Gottschalk, John Grodd, R. S. Dean

"Elemantary ConsiderationsAlthough magnetiem was first discovered in and derives its name from an oxide of iron found in magnesia and called lodestone its pracical uses date from the discoveries of Faraday concerning its relation to the electric current. We may therefore start our discussion of magnetic properties with Faraday's law for relation between induced electromotive force and the change in a magnetic where e is the electromotive force induced in an electric circuit by a unit rate of change of magnetic flux N, H is the intensity of the magnetic field, S is the area enclosed by the circuit, and i an angle between H and the normal to dS. In the simplest case we could use this law to measure the strength of a magnetic field by passing it at a measured rate through a coil of copper wire and determining the,electromotive force. As a matter of practical convenience, it will be simpler to nee the total quantity of electricity produced by a change of magnetic field. For this purpose we may let i denote the strength of the electric current induced by the change of magnetic field in time in a circuit of area a and resistance R. Then the total electric quantity. Q is given. by"

Mar 1, 1934

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By C. Sun

With complex component, higher salt content, low biodegradability, DSD acid oxidation wastewater could not be efficiently dealt with traditional methods. It is pointed that the coal water slurry could be made with DSD acid oxidation wastewater of different concentration and the density of coal water slurry could be up to 70%, while its viscosity is only 850~930 mPa?s. The coal water slurry could be perfectly jetted and burnt under different conditions. The higher density the DSD acid oxidation wastewater has, the better properties the coal water slurry have. The pollution components and characteristic group of DSD acid oxidation wastewater are similar to the additives of coal water slurry, so it could be used as a kind of usable additive of water coal slurry. It is so reasonable and feasible to make coal water slurry with DSD acid oxidation wastewater that the pollution of DSD acid oxidation wastewater can be solved completely.

Feb 23, 2014