Search Documents

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By William Gleason

"Caterpillar is the largest manufacturer of mining equipment in the world. In hundreds of surface mines around the globe, Caterpillar’s flagship 793 haul trucks can be found moving material for copper, coal, gold, iron ore and other mines. Likewise, its iconic yellow bulldozers are at mine sites the world over — the company recently announced the sale of its 40,000th large dozer. And since its acquisition of Bucyrus in 2011, Caterpillar has positioned itself to become a worldwide leader in the underground mining sector as well.But don’t think that the company is resting on its reputation. As evidence of its commitment to the global mining sector, as well as its confidence in the future of mining, Caterpillar invited mining trade press, including Mining Engineering, to its Tinaja Hills Training Center near Tucson, AZ in November to introduce the latest editions to its mining portfolio. The two-day event focused mostly on the newest electric drive haul trucks, the Cat 796 AC, which will operate in the 326-t (360-st) class, and the 798 AC in the 360 t (400 st) weight class.Caterpillar representatives also spoke about new offerings in the underground space as well as the newest version of the D11 large dozer.“It has been 10 years since we launched the F Series,” Jean Savage, Caterpillar’s vice president, surface mining and technology said. “Since then, we have been on a journey to serve our mining customers and we wanted to have trucks in every application. Today, we are launching two new trucks that will allow us to fill out our portfolio.”While Caterpillar previously offered the broadest range of off-highway haul trucks to the mining industry, it was noticeably absent from the 326-t (360- st) and 360-t (400-st) weight classes."

Dec 1, 2018

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Frank Mucciardi, Zhongsen Yuan

A new heat transfer technology --- termed Thermopump technology has been developed. This technology originates from conventional heat pipe configurations but has now evolved into its own class of heat transfer units, which we refer to as `Thermopumps (TP)'. A key feature is that Thermopump technology can be applied to high temperature / high heat flux environments where conventional heat pipe technology fails. Moreover, when implemented in less demanding applications where heat pipes appear to operate, Thermopump units have been found to function more smoothly and reliably. This paper will introduce Thermopump technology and several applications of this technology in steelmaking and refining will also be discussed. In addition, this paper will focus on three classes of applications: 1) waterless, non-consumable, high efficiency Thermopump oxygen lance and/or burner for EAF's, 2) Thermopump ladle lance for the desulfurization process, and 3) Thermopump cooling panels for furnace walls and roofs. Facilities equipped with Thermopump technology are expected to he better than the current corresponding ones in terms of increasing productivity and energy efficiency while at the same time lowering operating costs.

Jan 1, 2004

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

By R. L. Merrifield

Cominco Snip is a 60: 40 joint venture of Cominco Ltd. and Prime Resources Group Inc. Cominco manages the operation. The mine site is located in a narrow mountain valley where Bronson Creek enters the Iskut River in Northwestern British Columbia. Access is by air only to the company's 1,500 meter airstrip. Milling at a designed feed rate of 300 tpd began on schedule in January 1991. Tonnage and gold production in the form of bullion bars from the gravity circuit and gold bearing float concentrate have exceeded design forecast. This presentation will examine many of the factors that influenced the final plant design inclusive of exploration findings, bench scale and pilot plant test results, environmental and social considerations, capital and projected operating costs and product transportation alternatives such as the operation's Hovercraft.

Jan 1, 1993

By Pascual Perazzo Vaschetti Gabriella

The increasing emphasis on environmental issues has crucial importance in mining projects, hence in tailings dams. Their water barrier needs a two-fold environmental assessment: the environmental impact caused by construction activities, and the environmental impact over time. Unfortunately, tailings dams’ failures have great and long-lasting environmental consequences, and as mining sites become bigger and tailings dams higher, the risk of failures may increase. Furthermore, since these dams are mostly constructed over many years, design parameters/materials may change, the engineers may change, and since cost is a driving parameter, less attention may be given to quality control and monitoring. Geomembrane water barriers mitigate such impacts.

Sep 30, 2022

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres' pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By AIME AIME

APROXIMATELY one third of the world's iron ore is mined in the United States; and about 80 per cent of this third is mined in the Lake Superior ore region, and about 60 per cent in Minnesota. The Lake Superior iron ore region covers a vast area in the vicinity of Lake Superior that contained in early geological times large areas of iron-bearing sediments, which today form metamorphosed iron-bearing rocks, such as jasper, chert, taconite, and slates. Concentration of the iron content chiefly through solution and resultant removal of silica produced the ore bodies we find today in rock folds as on the Menominee range, at dike or impervious wall intersections such as on the Gogebic range, and blanket-type enriched ore bodies ly¬ing on or within the ore formation, such as occur on the Mesabi and in steeply pitching ore lenses elsewhere. In many places, folding and subsequent erosion of the tops of the folded areas has resulted in steep dips in the ore formation and contained ore bodies. The upper eroded edges are mostly buried under glacial over-burden. The slightly dipping Mesabi formation is the principal exception as to steeply dipping ore bodies.

Jan 1, 1941

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

By Ph. Cauwe

This paper presents the experience that NESA and MECHIM have gained about recovery of non ferrous and precious metals from complex sulfide materials. Processed materials are from natural deposits or metallurgical by-products or residues. Roasting of these materials is closely related to the pyro or hydrometallurgical processes used downstream of the roasting. Conditions of a first step of roasting the SELECTIVE ROASTING, are analyzed and explained. The roasted products so obtained are characterised by an extended elimination of volatile sulfides (AS, Bi, Sb, Sn, Pb, Hg, ?? ) and are readily available for the pyrometallurgical recovery of non ferrous and precious metals. After the SELECTIVE ROASTING, thanks to. the high porosity obtained in the "selective calcine", the SULFATE ROASTING is per-formed in excellent conditions. Hydrometallurgical tests performed for the final calcine show a high recovery of non ferrous and precious? metals and require only simple and well known processes. Many experimental and commercial data are given.

Jan 1, 1983

By J. S. Stachulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The first objective is to prevent a fife.The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife.The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife. Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By J. S. Stacbulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The flirt objective is to prevent a fife. The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife. The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife.Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By Corby G. Anderson

Since 1985, the Sunshine Mining Company has used a patented nitric-sulfuric acid pressure leaching system for production of silver and copper from a refractory sulfide ore body. To better understand this novel process, a program of lab scale testing was undertaken to quantify the effect of system variables on silver recovery. Some of the factors studied include temperature, agitation, acidity, vessel pressure, particle size, percent solids and oxidizer amount. In turn, this knowledge will be applied in actual plant practice to upgrade reaction time, increase concentrate throughput, raise silver recovery and lower reagent costs. A discussion of plant process changes resulting from lab scale testing is included.

Jan 1, 1991

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001