Search Documents

By C. P. Davenport

At the risk of belaboring certain facts which have so often been stated in the past, please bear with me while I set the stage. What are the projected electrical power needs of the nation and of the Northwest during the next 15 to 20 years? No one who has researched the subject over its historical past has reached a substantially different result than the following simple conclusion: electrical power requirements are doubling every decade. There are some who question the necessity of a power company's need to install capacity every ten years equal to what it has done during its entire previous history; there are even those who would argue that such growth should be arbitrarily curtailed. We are not here today to decide who should have light, heat, jobs and comfort, for we know that a power company must, by law, meet its responsibilities of providing the energy the public expects when the switch is thrown. The Northwest area (the States of Oregon and Washington), for which I speak, has the same case history of electrical power need as does the nation as a whole, and the requirement boils down to roughly an average of a million kilowatts of new capacity each year over the next ten years and we can estimate an average two million kilowatts per year in the 1980's. This is simple arithmetic, but the problems of meeting this exhausting schedule are a real challenge. The subject to which I address this paper is the role that Western Coal will play in the 6 billion dollar investment in these power generation stations. That 6 billion dollar figure represents today's dollar value and you may wish to apply your own escalation - frankly, I haven't the courage.

Jan 1, 1972

By William L. Crentz

In a Nation-wide appraisal of coking-coal reserves and of the practicability of upgrading marginal deposits to metallurgical standards, this study of the preparation characteristics of the coals in Cambria County, Pa. , was undertaken. Over 90 percent of the coal remaining in Cambria Comity is found in the Upper Freeport, Lower Freeport, Upper Kittanning, and Lower Kittanning beds. The Middle Kittanning bed, although mined on a commercial scale in the past, is not an important bed now, as most of the remaining reserves are too thin to be mined over wide areas. For many years, Cambria County has been an important source of coal for industrial and metallurgical purposes. The) principal production comes from the Lower Kittanning bed, which accounts for almost .60 percent of the Cambria County coal output. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1950

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the Cost Approach category for Real Property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves, and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties.

Jan 1, 2011

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

By M van Kampen

The Resource Management Act 1991 has been amended on a number of separate occasions since its enactment in 1991, and has recently be subject to further amendment by way of the Resource Management Amendment Act 2005. The amendments as proposed in the Resource Management and Electricity Legislation Bill would have had revolutionary and far-reaching consequences. However, as finally enacted, the amendments are a greatly watered down version of what was initially proposed. &nbsp; Nonetheless, the Resource Management Amendment Act 2005 has provided for a number of amendments that will impact on the minerals industry to varying degrees. This paper discusses in particular the changes and impact of the changes to the definition of æcontaminated landÆ, clarification with respect to the duty to consult, amendments to the provisions relating to National Environmental Standards, and to the council and Environment Court hearing process.

Jan 1, 2005

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991

By P. A. Von Wielligh

Without minerals, man cannot possibly hope to maintain his present standard of living. Professional mining men throughout the world, particularly in mineral-exporting countries like South Africa, are faced with the increasingly difficult task of ensuring adequate supplies of minerals. The problems of gradually diminishing mineral reserves and rapidly rising mining costs can to a certain extent be overcome by the use of more-sophisticated technological techniques and by the improvement of efficiency wherever possible. However, there is growing concern in some quarters, that, despite the ingenuity of engineers, geologists, metallurgists, and scientists, the earth&apos;s mineral reserves will eventually become insufficient to meet man&apos;s needs. In order to ensure the continued well-being of the earth&apos;s population, it is therefore imperative that more attention should be paid to mineral research and the training of specialists in the field of mineral reclamation.

Jan 1, 1978

By J. Mastoris

The growing environmental awareness and the need for providing social service to the community, urge the primary sector companies (such as mining) to find new solutions, by adjusting their operations with the special, local conditions and meeting everyday problems in practical ways. We hereby present a real case of re-design of an open pit, closed-bench type industrial minerals (clay) excavation, for the purpose of rehabilitation and utilisation as a water reservoir. The potential use of rainfall water was studied on the basis of covering the irrigation needs and improving the living standard of the neighbouring farmers and also as a project or recreational development of the area by shaping a wetland. The experience from the project progress and the reservoir use has been positive to date and the reclamation plan seems to have the acceptance of the local community.

Jan 1, 2002

This paper will examine some of the significant developments in the training field in Australia in the past decade and the application of these changes to the mining industry generally, and the coal sector specifically. Three major aspects will be examined:1. Competency - the use of Industry Competency Standards and how these can be used for achieving enterprise performance requirements2. Assessment - making judgements about an individual&apos;s competence, and using a rigorous assessment system as the basis for the "authorisation" system at a mine3. Evaluation - ways to evaluate the return on investment in training, and convincing CEO&apos;s/shareholders that your training dollar is being spent wisely.Before examining these issues, it is important to understand the drivers of change in the training systems in Australia, and the functions that Industry Training Advisory Bodies (ITABs) perform.

Jan 1, 1998

The Australian lead-zinc industry faces a future in which the world market is likely to show at best only minimal growth and in which there will be increasing competition. Its production facilities use mature technologies employing expensive labour and increasingly costly energy in a country which demands the highest standards of environmental performance. Returns on investment are already unsatisfactory.Technology for survival would appear to indicate a need not only for more efficient capital, labour and energy usage combined with improved environmental performance, but also flexibility to handle more complex materials than the traditional, virtually single metal concentrates. This offers the potential for improved overall economics from the mine onwards, but will demand efficient separation and by-product recovery processes.In the lead industry these problems are being addressed in several emerging technologies. With zinc, the situation is less clear.

Jan 1, 1985

By E. D. Seymour

Minera Yanacocha operates a complex heap leach gold facility in the Northern Andes of Peru. Four leach pads and thirteen solution storage process ponds form an extremely complex system. Distinctly different wet season and dry season rainfall accumulations present unique challenges to the process water balance. Minera Yanacocha operates four excess water treatment facilities which discharge water to the environment at specific quality standards in order to maintain a balanced system. Numerous government agencies and non-government organizations are involved with the permitting, monitoring and control of the discharged water. Minera Yanacocha maintains a relationship with 65 villages and communities, with a population of approximately 29,000 people and the city of Cajamarca with approximately 100,000 residents. This paper provides a high level review of the system complexity, the water balance, the excess water treatment facilities and social aspects of solution management.

Jan 1, 2004

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

Material sampling theory is well established in mineral process monitoring, improvement and control. It has been much enhanced by fundamental contributions due to Gy. When GyÆs sampling theory is applied to sampling inspection and monitoring, it provides estimates of average quality or extent of contamination. It also provides estimates of uncertainty, but these often ignore uncertainty in estimated variograms or other measures of variability. Risk assessment is often an implied task in sampling inspection and quality monitoring. A valid technique of risk assessment needs to take into account the uncertainty in the variational measures themselves. Standard statistical tolerance limit calculations which do take such uncertainty into account can be adapted to develop a technique for handling uncertainty in variational measures such as the variogram. Data from a published example is used to illustrate the technique.

Jan 1, 2005

By N. L. Piret, E. N. Mounsey

Ausmelt technology is successfully used to process primary and secondary materials to produce lead in large-scale commercial operations and to meet stringent environmental standards. The development and commercial data covering these applications and the results with respect to metallurgical, cost and environmental performance are reviewed in commercial operations. A new smelter is scheduled for commissioning in 2000 at Korea Zinc's Onsan site to process lead fume and other secondary materials to produce 50,000 tonnes per annum of lead bullion. The unique features of Ausmelt technology also allow for the efficient processing of polymetallic concentrates and secondary materials, particularly copper and lead, through the effective separation of these elements into metal, slag and fume species. This capability has been successfully demonstrated at a commercial scale and the results and implications for the industry are discussed.

Jan 1, 2000

By Mark C. J

Since the commissioning of the BHAS Copper Plant in 1984 the copper electrowinning operations have not fully met expectations. During 1988, a laboratory scale electrowinning unit was constructed to enable an investigation of the effects of process parameters on copper cathode deposition and quality. The process parameters investigated were copper concentration, acid concentration, current density, electrolyte temperature, electrolyte flow, electrolyte impurities and electrolyte additives. The findings of this research program indicate that there is an optimum cathode deposition morphology which results in good quality copper deposits which have improved stripping characteristics. All of the process variables investigated influenced the copper deposition and therefore it was necessary to delineate a suitable operating envelope for the copper electrowinning. As a result new standard operating parameters in electrowinning have been implemented which has enabled the production of higher quality copper cathodes with improved stripping characteristics.

Jan 1, 1989