Search Documents

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By Evans E. C.

Discussion of the paper presented at the Manchester Geological and Mining Society' general meeting held in Manchester, March 14th , 1916, with Leonard R. Fletcher, President, in the Chair included contributions by Fletcher L.R., Paton J.D., Orchard A.J.A., Ross A., Gerrard J. and Stephenson H., with the author's responses

Dec 1, 1916

By S Hall

Mining schools around the world, many unfortunately now closed, were often established to teach the techniques of narrow vein mining and associated processing to students studying part-time while working in the industry. This arrangement ensured graduates (or æassociatesÆ) had a mix of skills and knowledge invaluable to the industry.It is argued that there is still a need to educate students in these narrow vein techniques and that there will be a growing demand for such graduates with a high level appreciation of this type of mining. There is also a need for innovation in narrow vein mining and processing to develop specific technologies and allow the use of techniques applied in æbulk miningÆ to achieve improvements in productivity, safety and economic performance.This paper aims to review the situation with regard to education and innovation in narrow vein mining.CITATION:Hall, S, 2012. Narrow vein education - back to the future?, in Proceedings Narrow Vein Mining 2012 , pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By R. S. McCaffrey

In addition to its importance in agricultural production, Wisconsin is a very large manufacturing state and its rank in the metal working industries is probably first among the States of the Union per unit of population. The University of Wisconsin is a state supported institution and the Wisconsin tradition has always emphasized the relation of the University to the state and its responsibility to exercise its leader-ship where it might, in any and every way, for the development and benefit of the state and the community. The Department of Metallurgy of the University realized its responsibilities in the carrying out of the co-operative tradition and, two' years ago, an experiment was started in co-operative research between the University and certain of the industrial plants of the state. At the present time this work has so far progressed that it is no longer an experiment, and its results prove that this co-operative research may be carried on very advantageously and that, under the conditions existing in the state, the method employed has been satisfactory.

Jan 1, 1926

By Fred A. Webber

STEEL ROPE WIRE is one of the more specialized commodities among the many grades of highcarbon steel wires. In its production there are many metallurgical aspects of interest from the steelmaking on through the final stages of wire drawing. We produce rope wire in an integrated mill com prising all the operations from the blast furnaces to finished wire drawing in the wire mills. Steelmaking is carried out with close control on hot metal, selection of scrap, and fluxing materials. The basic open hearths are of 170 tons capacity. Steel is teemed into 19 1/2 in by 19 1/2 in big-end-down molds and is hot-topped with the use of clay refractory hot-tops. The weight of this ingot is 6,900 pounds. All high -carbon steel ingots are charged hot into the soaking pits and are then rolled through the blooming mill in 16 p asses to a bloom ax~ in. by 41/2 in. and approximately 65 feet long. Necessary bottom and top crops are taken on the bloom as it passes from the blooming? mill to the billet mill. The still hot bloom is continuously rolled through the billet mill in . 5 passes to a 2 3/8 in. square. Billets are cut to 32 feet in length by a flying shear and then allowed to cool on the hot bed.

Jan 1, 1957

By Mingchun Lu, Zhijia Liu, Xueqi Zhang, Jianliang Zhang

"In order to solve the problem of shortage of scrap, especially high quality scrap, a new substitute for scrap or DRI has been developed. The decarbonization mechanism of granular pig iron has been analyzed and the technical process and decarbonized granular pig iron have been evaluated in this paper. The research result shows that this new process is superior to direct reduction process in product quality, construction investment, operation flexibility, production efficiency etc. Decarbonized granular pig iron (DGPI) not only can be used as conventional scrap but also can be charged into EAF as high purity .burden equivalent to heavy scrap:IntroductionIn the past years, with the universal application of continuos casting technique in China, the amount of scrap generated inside steelworks has been reducing continually. On the other hand, the EAF steel proportion is increasing and this gives to the obvious change in structure of steel product. At present, the requirement on both scrap quantity and scrap quality is being paid more and more attention. Because China is a country which is devoid of scrap and poor in resource (nature gas and high grade iron ore) for developing direct reduction iron (DRI) so that sponge iron can not be produced cosmically in China and has to be mainly imported. Instead of part of scrap, some cold pig iron in cold state has been charged into EAF in China. However the high carbon content in pig iron has limited its proportion in EAF metal burden. Because the price of pig iron is lower than that of imported DRI in China, the technique of granular pig iron decarboniztion is hopeful to become effective way to produce substitute for scrap or DRI."

Jan 1, 2000

By Roger L. King

The Bureau of Mines has developed probes to be used in emergency mine rescue operations by being lowered through a borehole drilled into an underground mine. Various probes can provide two-way voice communication with trapped miners, continuous mine atmosphere monitoring, temperature indication, and television searching capability. At present, an infrared imaging probe is being developed for "seeing" through coal smoke.

Jan 1, 1976

By Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"The LCDs are used in televisions, calculators, mobile phones, computers (laptops and tablets), video games and other electronic devices. The advancements in technology make obsolete these devices, causing excessive disposal of LCDs and therefore decreasing life span of landfills. In this context, the LCDs from LED LCD TVs arise as an additional source of waste electrical and electronic equipment (WEEE). Thus, it is essential to develop LCDs recycling methods, beginning with the LCD characterization followed by displays processing, aiming the materials separation and using some Ore Treatment Techniques, and finally, the recovery of indium using acid leaching. The analysis methods that will be used in this work are: Fourier Transform Infrared (FT-IR) and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES).IntroductionLiquid Crystal Display (LCD) technology is applied in modem televisions, calculators, mobile phones, computers and a wide range of electronic devices. It has replaced Cathode Ray Tube (CRT) technology as the most advantageous display product, due to lower electrical power consumption, size and weight reduction, and no radiation emission [ 1]. The constant improving of LCD screen technology reflects on its growing contribution to the amount of waste electrical and electronic equipment (WEEE): an estimated 50 million tons of WEEE are produced every year [2]. Once the most common method of its disposal are landfills, the LCD technology therefore became an environment issue [3].LCD structure is composed by components made by different materials. In order to develop a LCD recycling methodology that gives the right destination to these materials, a previous characterization stage is required. This characterization includes a disassembly process and material identification analysis. One of the LCD components is the screen, which is composed by polymeric and glass layers. The liquid crystal glass was the starting material of this study. It contains indium in the form of indium tin oxide (ITO) film. This ITO film is deposited in the glass by a sputtering process and acts as the electrode material [4,5]. It has in its composition 90% ofln203 and 10% ofSn02 [6]."

Jan 1, 2014

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By J. D. Sloop

This paper discusses the current state of EAF dust recycling at AmeriSteel's Dust Processing Division in Jackson, Tennessee. Included are a brief history of the plant, a description of the facility, a description of the process, and operating data.

Jan 1, 2000

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By Wayne Bell, Matthew Andriese, Shuqian Xie, Jiann-Yang Hwang, Zhiwei Peng

"Pyrolyzed carbons are generally known as good microwave absorbers and their dielectric properties still remain to be fully explored. In the present study the dielectric properties and dielectric polarization-relaxation phenomenon of a typical activated carbon was investigated. The experimental results indicate the complex permittivity is highly dependent on temperature and frequency. The decrease of permittivity with increasing temperature from room temperature to ~100 °C is probably ascribed to the release of the water vapor adsorbed on the surface of activated carbon, and the variations of permittivity with temperatures between 100 °C and 450 °C in the frequency range of 300 MHz to 3000 MHz are mainly attributed to the decreased relaxation time of dielectric polarization.IntroductionPyrolyzed carbons have been identified as excellent microwave absorbers owing to their high dielectric and electrical loss under microwave irradiations. Among them, activated carbon continues to attract more and more attention from researchers. Due to its special physical properties, the production, modification and regeneration of activated carbon with the assistance of microwave have been widely studied over the last few decades [1-6]. However, only few attempts have been applied to explore the dielectric properties of such materials due to the complexity and variability of their organic precursors and activation processes [7,8]. In order to shed a light on this problem, a typical sample, Norit® A Supra USP powdered activated carbon, was adopted to perform dielectric characterization, which may provide useful information for its wide application in the fields of purification, energy (hydrogen) storage and so on."

Jan 1, 2011

By E. S. Wheeler, M. W. Murphy

A LARGE part of the molybdenum produced in Colorado is converted and consumed in the Eastern States. As the raw materials and the power needed for the conversion of the Colorado concentrate are also accessible in the Eastern States, the conversion plant has been installed some 1500 miles east of where the ore is mined and milled. When concentrate was first produced at Climax in 1918, a custom smelter converted the product into ferromolybdenum. By 1924, the Company had decided to produce calcium molybdate and rented a building and installed equipment for that purpose at Langeloth, near Burgettstown, Pa., about thirty miles west of Pittsburgh. For the first few years the plant was a simple one of small capacity. A small hand-rabbled roaster was used, the product of which was made iota calcium molybdate by a conventional method; then an eight hearth mechanically rabbled roaster was installed to increase and speed up production. The output was considerably less than a million pounds of contained molybdenum annually until 1928, when a small part of the produc-

Jan 1, 1946

By Neusa Alonso-Falleiros, Aristeu Braz da Veiga, Marcelo B. Mourão, Adriano Pescarmona, Antonio Alberto Froes Schettino, Cyro Takano, Carlos A. S. Giraldo

"The Caron process of nickel extraction from lateritic ores produces a fair amount of an inert residue, the so-called “black sludge”, that is disposed in a dam according to the required environmental regulations. On the other hand, it represents an opportunity to resource recovery. This work presents the characterization of the residue, discusses some possible ways to recover the valuables, and presents experimental results of pyrometallurgical runs aimed at recover nickel as an iron-nickel alloy. It has been shown that the residue contains large amounts of silicon, iron, aluminum and magnesium, in the form of oxides and silicates, and small quantities of nickel, cooper and cobalt, besides several other elements. It has also been shown that gravimetric or magnetic concentration methods do not present promising results. On the other hand, it is possible to obtain iron-nickel alloys by high-temperature carbothermic reduction of the “black sludge”.IntroductionThe Caron process consists of a combined pyro-hydrometallurgical process to extract nickel from high iron limonitic lateritic ores, recovering also the cobalt present in the ore. The main steps are the reduction roasting of the ore, aiming at a selective reduction of nickel and cobalt to the metallic state, avoiding as much as possible iron reduction, followed by leaching with ammonium carbonate solution and the recovery of metal from the pregnant liquor [1,2]. As a result, significant amount of tailings are generated, that are disposed in appropriate dams. This residue, called “black sludge”, contains significant proportion of silica and iron, and also small amounts of nickel, cobalt, cooper and some other elements. Due to diminishing deposits of nickel ore, high metal prices and a significant amount of “black sludge “ available after several years of operation of the plant, Votorantim Metais, who operates a facility in Brazil that uses the Caron process, decided to explore the possibility of recover nickel from the residue. This paper presents the characterization of the residue, and the results of experimental work aiming recovery of nickel from it."

Jan 1, 2008

By Frank G. Breyer

C ONDITIONS have not been favorable for new developments in any line. It has been a period, how- ever in which recent developments have been subjected to the severest tests. Those which have been able to hold their own in the severe competition of 1932 must be considered fully proved commercial processes. The continuous vertical-muffle retort plant at Palmer- ton is reported to have been in operation at practically full capacity throughout the year. The high quality of metal produced and the low operating costs are factors which have kept this plant running when many of the older furnaces were shut down. The plant at Meadow- brook, W. Va., is also reported to have been in steady operation throughout the year. Average retort life is said to be better than two years with about three-quarters of the original retorts still in operation after 2 ½ years.

Jan 1, 1933

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015

By O Salisbury

Ingress of air into the longwall goaf environment needs to be managed appropriately to reduce the risk of creating a spontaneous combustion event. The maingate goaf edge is an area of particular concern in this respect, as air often penetrates for some distance into the goaf along this region inbye of the longwall face. Since the flow rate in this part of the goaf is also quite low, an opportunity exists to disrupt the air pathway by implementing a barrier to the airflow. Previous attempts using plugs made from an assortment of materials have resulted in varying degrees of success. More recently, Narrabri Coal Operations (NCO) has introduced the use of a chemical foam that is mixed with nitrogen to produce a standing barrier with the consistency of shaving cream. The implementation of this practice has consistently proven to be very effective for reducing the oxygen concentration along the maingate goaf edge by systematically retreating the foaming unit with the longwall. This paper presents how the foam is applied in the underground goaf environment to prevent oxygen ingress and uses results from gas monitoring to confirm the foam effectiveness.

Oct 12, 2022