Search Documents

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By S. E. Haszko

SEVERAL new XGa2 intermetallic compounds, Table 1, where X is a rare earth, having the AlB, structure were prepared as part of a continuing study of the magnetic and structural properties of rare-earth alloys.' In this note, the crystallographic results of these compounds are presented. Chart, Eq. 121 for the data in Fig. 1 can be adequately represented by The corresponding standard free-energy change is AF; = -4.576 T log K = -20,900 + 10.20T [5I At low nitrogen concentrations the ratio of mole fraction to weight percentage is a constant so that the mole fraction X of nitrogen is given by X = 0.0392 [%NJ. At low values of X, the activity and the concearation approach each other, hence K, = 0.0392 K,, where K, is expressed in terms of the mole fraction of nitrogen. Hence Eqs. [4]. and [5] become

Jan 1, 1962

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alternative: the fully optimized use of the facility&apos;s present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements in the mine or plant necessary to support new technology will be equally effective when implemented for the facility&apos;s present operators. Firms that optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 2000

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By O. A. Bascur

Applying the latest information technologies in mining and metallurgical complexes has become a serious challenge to management and technical teams. Emerging component design is changing the way the user relates to the desktop. Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. The integration of information from mining, mineral processing and metallurgical performance monitoring increases production efficiency, even when many elements cannot be measured directly. Three case studies of large mining/metallurgical complexes are highlighted.

Jan 1, 1999

At Yucca Mountain, USA, a tunnel is being built according to nuclear quality standards. It has proved possible to meet very high quality demands while at the same time achieving high advance rates. To be able to do this, routines on how to record and store quality related information have been established. This has meant that a new philosophy has entered the tunnelling industry. Especially for nuclear waste projects, of which Yucca Mountain is one of the first ones to be built, the experiences made and the quality assurance program established will be of great importance for future projects. The paper gives examples of what the Nuclear Quality Assurance system has meant in practice for the tunnelling at Yucca Mountain. And, it also explains why a non-grouted bolt, Super Swellex-, was chosen for long-term reinforcement in the tunnels which might host nuclear waste for thousands of years.

Jan 1, 1999

By F. Woodcock, A. R. Laplante

A test to characterize the amount of gravity-recoverable gold (GRG) in an ore is described. Typical GRG results are given and possible uses are discussed. The overall database, which includes 68complete tests, is presented. The ore samples treated had an average GRG content of 63% of the total gold in the sample, with a standard deviation of 20% and a range of 3% to 97%. Both the F8(, of gold and the GRG content at a grind of 100% finer than 850 pm correlate well with the overall GRG content (at 80%finer than 75 pm). The primary use of the test is to determine whether gravity recovery should be used and how. Results can also be used to predict gravity recovery, as many of the ores tested are from plants employing gravity recovery. Gravity-circuit simulation can be used to refine recovery estimates or for optimization studies.

Jan 1, 2000

By M. Beus, S. Stewart, S. Iverson

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods and better hang-up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mockup of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were compared Loads on an active ore pass chute were measured

Jan 1, 2000

By B. Tönjes

In the course of the last decade, the concept of sustainability has turned from a catchword into a vision - a vision to which politics and industry feel increasingly committed. In terms of the energy industry, the key criteria for sustainable development are supply security, economic efficiency and social responsibility. Coal is able to meet all these criteria if it is produced in conformity with high safety standards through the use of modern mining technology and converted into electricity with the aid of environmentally friendly methods. Among the fossil energy resources, coal will, according to the vast majority of global energy scenarios, continue to be the most important input energy in power generation for the foreseeable future. Coal is therefore today, and will in future continue to be, an important element in ensuring sustainable energy and raw material supply, worldwide, in Europe and also in Germany.

Jan 1, 2005

By Daryl R. Tweeton, William H. Engelmann, Orin M. Peterson, Jon K. Ahlness, Gregory R. Anderson

The Bureau of Mines measured the geochemical changes as H2SO4 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen,HC03, U. V, Na, K, Ca, Mg,S04, CI, Mo, Mn, Fe, AI, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V =kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By Hainsworth D, Winstanley G, Gurgenci H, Corke P

Past experience has shown that the automation of the dragline swing motion requires real time monitoring of the bucket position. A current project at the Centre for Mining Technology and Equipment (CMTE) is aiming to achieve this using machine vision. The hardware platform is a Datacube MaxVideo 200 system. The images are obtained by a fixed camera installed on the dragline boom. The field of view is large enough to include the bucket in all possible configurations. Standard chain coding and run-length coding algorithms are used to process the video image. The three-dimensional bucket position is calculated by combining the output of the machine vision system with the rope length data obtained from transducers installed on drag and hoist drums. This information is then fed into a control computer which takes corrective action to suppress bucket oscillations before they reach dangerous levels.

Jan 1, 1995

Managers are demanding efficient use of their resources and part of this demand is leading to the idea of integrated audits for Occupational Health and Safety (OH&S), quality and the environment. It is possible to construct audits which test the compliance in this area with standards established by management systems and it may be that such an integrated audit of a site could reduce the time of auditing and be equally effective as three separate audits. However, this is only a maybe. To do an audit on all three aspects when they are not fully integrated results in more time wastage than doing three separate audits. But organisations are not structured around the audit process (some financial managers may query this statement). The organisational management systems are put in place to achieve the organisational goals - presumably in an efficient and cost-effective manner.

Jan 1, 1995

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

Within the Mt Whaleback open cut mine the integrity of the final pit wall is achieved through careful rock slope design, use of rock reinforecement technology where marginal stability exists and use of controlled blasting techniques and excavation practices. By reducing the effective density of ANFO explosive within blastholes to around 0.2 glcm&apos;, and developing standard blast pattern designs for various rock types, blast damage to pit walls has been minimised. Accurate geological prediction is necessary for optimum blast design. Controlled blasting is undertaken where blasting occurs within 90 m of the designed final batter crest and hole by hole assessment of final limit blast patterns is undertaken before pattern charging. Shovels and trucks remove the bulk of blasted and dozed rock material, but due to the mine&apos;s variable pit wall slope configuration, bulldozer excavation of some critical design batters has been successfully Implemented.

Jan 1, 1986