Search Documents

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By M. R. Geer, H. F. Yancey

"INTRODUCTION With the advent of war in 1941, military operations in Alaska were enlarged on such a scale that the demand for coal in the Territory more than doubled. Coal was needed urgently for heating forts and other military establishments, for use on large construction projects, and for handling the greatly increased volume of traffic on the Alaska Railroad. -The additional tonnage required, estimated at perhaps 250,000 tons per year, probably could have been supplied by the United States, but shipping space between Pacific Coast ports and Alaska was already overburdened with military supplies and construction materials. Moreover, although of only secondary importance in wartime, the cost of coal shipped into the Territory is reported to have been as high as $40 per ton. The alternative to importing coal was, of course, to increase the Production of the Alaska mines.Production of coal in Alaska reached, 350,000 tons in 1944, or more than double the prewar' output. The responsibility for increasing coal production was assumed largely by the Army, A Coal Commission attached to the Alaska Department arranged financial assistance for some mining operations, aided the operators in producing equipment for mechanization, and provided most of the labor necessary to operate the mines. The Bureau of Mines contributed to the program in several ways. First, exploration by the Bureau in the Moose Creek district revealed a substantial tonnage of coal of better grade than any currently mined in the Territory, 4/ and drilling in the Broad Pass district, where a mine to supply coal for the army had been started, revealed that the reserves were far less than had been supposed; this operation was abandoned. Second, coal-preparation practices were studied, and recommendations for improvements made, at two of the operating mines at which the quality of the coal makes preparation a factor of vital importance. Some of the information obtained in these studies forms the basis for the present report."

Jan 1, 1946

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

By J. D. de V. Louw

Introduction Zircon is a natural occurring mineral and may exhibit natural low level radioactivity. It contains trace levels (90 to120 pCi/g and 110 to 115 pCi/g respectively or 3.3 to 4.4Bq/g and 4.1 to 4.3 Bq/g) of naturally occurring radioactive uranium and thorium. This mineral is often found in a suiteof minerals (rutile, ilmenite and monazite) Due to the overlap in physical properties of monazite (containing 4–7% thorium) with some of the zircon (slight magnetic susceptibility) it often contaminates the zircon, adding to the levels of thorium in the product. Hazards associated with the products from zircon and its processing is inhalation of respirable dust (generated by milling) containing radioactive uranium and thorium which may cause cancer of the lungs. Legislature regulates the transport, use, workplace environment exposure and storage of radioactive material. In America the general regulation for the unlicensed use of low levels of radioactive materials limits the concentration to 500 ppm (U plus Th). Europe (IAEA) specifies a limit of10 Bg/g (Bequerels per gram) on the parents for transport only which is a higher level of U+Th. Companies selling into these markets need to comply with these regulations and certification is therefore required, not only of the major constituents determining the price, but of the U and Th levels as well. Exceeding the limits for U and Th may result in material being returned to the country of origin. However, for the analyst the requirement is to analyse for these elements throughout the production process as well as the analysis of the ‘tails’ that is returned to the mine area. This requires a wide range of concentration to be analysed. Methods of analysis A wide variety of methods exist for the analysis of U and Th in a range of matrices. (Table I) All these methods have been used with varying degrees of success in terms of accuracy. Overall precision for the different techniques varies from 5 to 25% relative. Time to produce results from these methods vary from a few minutes to several days. The Production Chemist is expected to produce between5 and 10 analyses per hour for process control purposes. A suitable technique that fits this requirement is X-Ray Fluorescence. Both Wavelength Dispersive (WDXRF) and Energy Dispersive X-Ray (EDX) instruments are suitable. X-Ray analysis in general has a few major advantages over competitive techniques. •It is fairly simple to set up and interferences are known and easy to correct •It has multi-element analysis capabilities •Clean spectral lines for U and Th (in zircon specifically) •Uncomplicated and easy to measure background •Low detection limits (3 to 5 ppm) •A very high degree of precision •Sample preparation is uncomplicated and fast (pressed powders and fused beads). In Zircon (ZrSiO4) processed sands the matrix is constant(>99% ZrSiO4) and the background is thus essentially constant. A typical set up for the analysis of U and Th by WDXRFis given below: X-Ray Tube Tungsten (W) Target, 2.5 to 3kW operated at 50mA/50kV Crystal LiF200 (or LIF220 for higher resolution) Analytical Lines (2?)U La1,226.14Th La1,227.47 Detector Scintillation Counter Analysis time, depending on the concentration can vary from as little as 20 seconds up to 5 minutes. Standards As with any other comparative technique XRF analysis relies heavily on the quality of the standards used. Assuming proper set-up and operation of the instrumentation as well as consistent sample preparation, accuracy is determined by the quality of the initial calibration standards. A search for the available zircon certified reference materials (CRMs) shows that there are only a few CRMs

Jan 1, 2003

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999

By José Adachi

La ventilación de minas es un proceso relacionado a la dinámica de la mina que genera el acondicionamiento del aire circulante a través de las labores subterráneas. Como tal, los requerimientos de la mina se adecúan de acuerdo a la estructura física de la misma. En consecuencia, no existe un sistema de ventilación estático puesto que los sistemas requieren de constantes monitoreos y ajustes para alcanzar una ventilación óptima. Así, el presente trabajo señala los aspectos importantes del diseño de ventilación principal de la mina Condestable realizado entre el período de 1992 y 1993 por encargo de la compañía minera. La metodología empleada comprende mediciones de campo y el cálculo de requerimientos del caudal. Asi también está la construcción del modelo de red de ventilación y el diseño del nuevo ciricuito con ventilación forzada.

Nov 24, 1993

By M. Kane, O&apos

BHP Iron Ore initiated research programs in January of 1995 to develop long term plans for decommissioning of the waste rock material at their Mt. Whaleback operation. More than 2 billion tonnes of waste rock were deposited during the past 30 years. Ultimately, the operators will deposit a total of approximately 5 billion tonnes in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semi-arid climate adjacent to Newman, Western Australia, approximately 1200km north-northeast of Perth, Western Australia. The primary research program includes the development of technology for the long term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion, and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. A laboratory program and the soil-atmosphere modelling completed to design the horizontal field test plots are described. The construction of the horizontal surface field test plots are discussed together with the field instruments installed to monitor performance. The key components of the instrumentation program are the design and installation of large scale field lysimeters to measure the unsaturated flow of moisture into the waste rock from the base of the cover layer. The cover system is designed to maximize infiltration during wet periods for subsequent evapo-transpiration while minimizing surface runoff. The result is a near zero net infiltration to the underlying waste material. A key feature of the design is the use of pit run waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long term performance.

Jan 1, 1998

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

By D. Harrington

Ventilation of underground workings consists of establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, mad without impairment of health; and that the mine openings may be made subject to such control of air flow as to remove from the workings at ordinary times harmful gases and dusts, and at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically operated fans, to ether with other ventilating devices such as doors, overcasts, regulators, etc. Every mine, large or shall, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims have been made that in specific mines there is sufficient natural al" flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion the mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them.

Jan 1, 1933

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By H. P. Hatch

Ash is a material that many people leave to nature to handle. Others sometimes sweep it under the rug to be disposed of by someone else. In our business we cannot do either. In fact the American Electric Power System spends many millions of dollars in plant investment costs to collect the material, and then many more millions to dispose it. In 1965 alone the coal fired steam generating plants in., the AEP System produced approximately 2,400,000 tons of ash, enough to fill 40,000 coal cars which would extend as a single train across the entire states of Ohio and Indiana. Even though our present ash production is large, this is only the beginning when we forecast the future growth of our system. By 1980 it is estimated that our generating capacity will expand to about three times its present size, and with coal as our primary source of fuel our ash production will increase proportionately to about 7 million tons a year.

Jan 1, 1966

By J Addai-Mensah, W Skinner, C Kelsey, J R. Kelly, E Baawuah

Comminution continues to be the most capital-intensive unit operation in mineral processing. The fundamental purpose of comminution is to liberate the valuable minerals so that they can be economically concentrated into saleable products. Declining ore quality characterised by lower grade and increased complexity requires significant energy consumption for comminution. Low-grade magnetite ores are typically fine-grained and require fine to ultra-fine grinding (P80 ~ 30 - 40 µm) to enhance its liberation from the typically siliceous gangue matrix. Historically, this has been achieved using multi-stage crushing and grinding technologies, which require high energy consumption with low energy efficiency. This motivated innovations in energy efficient technologies for comminution. Such technology has been developed in the IMPTEC super-fine crusher. It is an innovative, dry (with the potential to be operated wet), media-free, energy efficient crusher that can to reduce 10 mm feed particles to 19 – 30 µm with very low recycle loads. In this study, the mineralogical and physicochemical characteristics of crushed magnetite ore using the IMPTEC super-fine crusher have been investigated in comparison with those of rod milling. The super-fine crusher generated higher liberated magnetite minerals in the – 300 + 212 µm and < 45 µm size fractions compared to rod mill. Both comminution devices generated large low-grade hematite and goethite middlings. However, the rod mill produced higher locked/unliberated hematite and goethite compared to that of the super-fine crusher. Quartz mineral had the highest liberation irrespective of the comminution device used. The super-fine crusher generated higher entrapment of other minerals within the silica matrix compared to the rod mill. The breakage mechanism of the super-fine crusher which is predominantly through high compression with shear, generated improved mineral liberation in the coarse size fractions compared to the predominant abrasion and attrition breakage mechanisms of rod milling. The higher mineral liberation generated by the rod mill is potentially due to the prolonged batch milling of the ore compared to the single-pass open circuit of the super-fine crusher.CITATION:Baawuah, E, Kelsey, C, Kelly, J R, Addai-Mensah, J and Skinner, W, 2018. Mineral liberation studies of IMPTEC super-fine crusher – 130 crushed product, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 313–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A G. Rogers

This paper discusses the lubrication of surface and underground mining machinery and equipment from the standpoint of machine components. The machine components considered are bearings, cylinders, gears, chains, couplings, fluid drives, hydraulic systems, screws and wire ropes. The best selection of lubricants for these machine components, and for sub-divisions of the components, are outlined. They form general recommendations, for average operating conditions in both surface and under-ground mining operations. The American Petroleum Institute's service classification of both engine crankcase oils and gear oils is de-scribed and used in recommending products for these applications. The practical aspect of lubrication is kept foremost in the recommendations, which are designed to meet the requirements of a wide variety of equipment with the minimum number of lubricants. THE lubrication of mining machinery and equipment presents a variety of problems peculiar to the industry. The type of mine, the ambient temperature, water, dust, and operating and maintenance practices, as well as the age and condition of the equipment, are variables which have to be considered in making lubricant recommendations.

Jan 1, 1963

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By Eric Nelson

The paper point out the structural openings and the localization of ore bodies. Structural openings in rocks constitute the primary permeability network for the formation of most hydrothermal ore deposits. The distribution, geometry, density, and orientation of ore bodies in structural openings are controlled by two primary factors: the far and near field stresses and the mechanical properties of rock. When stress controls the orientation and kinematics of faults and fractures in the absence of pre-existing weaknesses, ore shoot orientation is perpendicular to the fault slip vector and can be predicted by kinematic analysis. However, when structural openings form along pre-existing weaknesses, ore shoot orientation cannot always be predicted by kinematic analysis. Because we can classify ore bodies based on the types of geological structures discussed above and the variations that naturally occur from material property heterogeneity, exploration for hydrothermal ore deposits should include analysis of geologic structure and evolution, rheological variations, pre-existing weakness, and fault kinematics to evaluate structuralcontrols on localization of ore bodies.

Apr 22, 2003

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By J. B. Zadra, H. J. Heinen

Electrowinning molybdenum from oxide feed materials dissolved in a variety of molten baths was investigated . A NaCl - NaF - Na₂ B₁ O -Mo0, system operating at 1,000 ° C in a cell without a protective atmosphere gave the best current efficiency , metal - to - cathode adherence , and purity of electrowon Technical - grade molybdic oxide , containing associated impurities of aluminum , iron , copper , silicon , and tungsten in combined quantities of 10 percent , was used as feed material to produce dendritic crystals of molybdenum metal containing less than 0.5 percent total base metal , carbon , and oxygen impurities . Arc - melting molybdenum electrowon from either chemically pure or commercial - grade Mo0, produced ingots that contained less than 0.1 percent total impurities and had hardness readings of 168 to 200 Vhn .

Jan 1, 1964

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022