Search Documents

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

[MUNOZ, P.: New Oil Fields in Trinidad, M27, 311 MUNRO, C. H., biography, M84, 354 MUNROE, H. S., biography, M83, 277 Muntz metal (See also 60:40 Brass): corrosion. See Corrosion of Metals. fatigue and corrosion-fatigue, 78, 597 heat-treated: cleavage structure, 83, 498, 505 grain growth, abnormal, 83, 503, 505 machinability, 99, 323 stress-corrosion cracking, 89, 249. 266 MURAKAMI, T.: iron-silicon diagram, 80, 253, 255 MURDOCH, J. A. W., biography, M28, 157 MURDOCK, W. J.: Discussion on Adaptability of Various Coals as Generator Fuel in Manufacture of Water Gas 78, 561, 565, 566, 568 MURPHY. D. W. AND CHIPMAN, J.: Solubility of Nitrogen in Liquid Iron (T.P. 591) 116, 179. Abs., YB35, 33; M35, 114 MURPHY, L. J.: Relative Advantages and Costa of Electric Power in Lease Operations 77, 219]

Jan 1, 1936

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

Geological information is essential for a diversity of public and other purposes, including land use planning, hazard mitigation, and the exploration and sustainable use of natural resources. This is especially important in New Zealand, where the complexity of the geology is due to its position on an active plate boundary - the ultimate cause of earthquakes, mountain building, subsidence and volcanic activity. The geological setting also controls the origin and distribution of New Zealand's varied mineral and energy resources. Providing information about the origin, quality and quantity of mineral resources has long been seen as a key function of national geological organisations such as the Institute of Geological and Nuclear Sciences. Such information is essential for wise land-use decisions under the Resource Management Act. One of the major goals of the Institute is to quickly and effectively disseminate research results to interested users. The most effective and internationally accepted method of presenting geological data is by means of geological maps, which show the distribution of rock types and structural features at the surface. Most countries have ongoing gelogical mapping programmes, and in recent years the need for up-to-date, reliable information has led to a trend to accelerate basic geological mapping (eg US National Geological Mapping Act 1992; Australian National Mapping Accord 1990; Plan 2000 in the UK). Over the last 25 years, the Institute of Geological and Nuclear Sciences and its predecessors (NZ Geological Survey and DSIR Geology and Geophysics) have concentrated on detailed mapping of priority areas selected on the basis of economic and scientific interest. This has included remapping of Nelson-West Coast and Coromandel, regions with high mineral potential, for which 1:63 360 or 1:50 000 maps have been prepared.

Jan 1, 1994

By S. Dallaire

With the attainment of high temperatures it becomes possible to process any kind of material (particularly ceramics) in their liquid state. In the plasma spraying process, the material to be sprayed is rapidly heated until it is molten and is propelled by high velocity gases onto a surface where it adheres, to give protective coatings for a wide range of applications. The method could be considered as one of the most versatile and rapid to build up thick deposits (of plastics, metals, ceramics, cermets) and also free-standing artifacts for particular requirements without resorting to lengthy forming and sintering studies. Although plasma spraying is at the production stage in industry, advanced processes have also been developed for economically producing a wide range of new materials. This paper illustrates the benefits of the process and evaluates the challenges it represents.

Jan 1, 1987

By Harold J. Rose

It is a real pleasure to attend another meeting of the Institute. This is partly because I am a Westerner by birth and training. As a young man I had personal experience with firing Colorado and Wyoming coals. The coal industry of the United States has done an outstanding job of producing coal. We can all be proud of the industry's record of continuously adopting technical improvements in coal mining. NEED FOR MORE EFFECTIVE COAL MARKETING However, it cannot be said that the industry has done an equally good job of marketing coal. There has been a rapid growth in U. S. population, and an even greater expansion of industrial demands for heat and power. Yet coal consumption for the past several years has been no greater than it was 40 years ago, in 1912 and 1913.

Jan 1, 1954

By Kato Y

As a direct result of the Mining Industries need to improve efficiency and production in Open Pit type operations, the size of haulage units have increased dramatically. This trend has continued such, that the majority of dump trucks operating in Open Pit operations are in the 170 ton class. Continued mining in existing locations has meant that the increase in vertical lift and resultant grades, and increases in hauling distances are making electric drive systems unsuitable. This is largely due to the electric drive systems heat limitations on major propulsion components. With these mining requirements in view and the present limitations on electric drive systems in mind, Komatsu have been developing the Komatsu HD1600M. A diesel powered mechanical drive dump truck capable of operating in deep pit operations. This presentation introduces: Komatsu HD1600M Dump Truck

Jan 1, 1982

By Bernard H. Hertlein

Transportation system structures have come under very close scrutiny in the last couple of years, largely due to the damaging effects of disasters, both natural and man-made. In the Pacific northwest and California, earthquake risk is a major concern. In the central and eastern states barge impacts on bridge piers and docks are a big worry. In all cases of bridges over water and waterside structures, scour is a primary concern. Some of the results of this scrutiny have been changes in design and construction methods, and the introduction of more testing to supplement field inspection during construction, and throughout the service life of the structure. Future construction of bridges and docks will almost certainly see a continuing growth in these practices. Where foundations are concerned, particularly for bridges and waterside structures, many state and local authorities have started specifying drilled shafts rather than driven piles. Where the shafts must be constructed under water or slurry, visual inspection of most of the work is impossible, and one of several different Nondestructive Tests (NDT) is often specified. Contractors' experiences with these methods have varied considerably, and there is a great deal of controversy in the deep foundation industry over the reliability of NDT methods for assessing the integrity of foundation shafts or piles. The author has had more than 15 years of practice with the various NDT methods for deep foundations, on projects all over the US, particularly foundations for bridges and dock structures, and has developed an understanding of the "NDT controversy" as it has become known. In particular, experiences in the Pacific Northwest, California, and Alabama have illustrated the reasons for the controversy. This paper reviews these experiences, and suggests some steps that owners and contractors can take to reduce the risk of inconclusive or downright inaccurate test results.

Jan 1, 1998

By Gary P. Sames

The Bureau of Mines recently initiated a study of geologic features that contribute to roof instability in western U.S. underground coal mines. The purpose of the study is to provide information for use in ground control planning and safety hazard reduction in that region, where mining activity has been increasing. Hazardous geologic conditions were surveyed in selected underground coal mines in Utah and Colorado, and both depositional and structural features were identified as potential ground hazards. Although the conditions found do not differ in kind from hazardous geologic conditions in the Eastern United States, they do differ in intensity of occurrence and relative importance. Three depositional features dominate where unstable roof occurs in western underground coal mines: paleochannel deposits, crevasse splay deposits, and flood basin deposits. Three structural features identified as hazardous, but not so widespread or common as the depositional hazards, are faulting, jointing, and igneous intrusions. This survey establishes a foundation for future studies aimed at reducing and preventing ground control accidents in western coal mines.

Jan 1, 1988

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By John H. Lichtblau

There are three parties to the oil imports controversy: the domestic oil producers, whose side has just been ably summarized by Mr. Jameson; the oil importers; and the public. Domestic producers and importers are both motivated by economic self-interests, that is by their natural and legitimate desire for profit maximization, in their respective positions. Thus, domestic producers, rightly, regard every barrel of imported crude oil (with the exception of some specialty crudes) as a displacement of a barrel of their own crude. Hence, the lower the import Level the better they like it. Conversely, U .S. refiners whose plants are located at the seaboard or at certain inland waterways generally welcome a higher level of imports because refiner profits are based primarily on the spread between the crude oil price and the refined products price, since crude oil represents by far the refiner?s largest cost factor. The relatively low cost of foreign oil means therefore higher profits to those refiners able to process such oil, This applies particularly to integrated companies whose own domestic oil production is insufficient, to meet their refinery requirements but who have developed ample low-cost foreign oil supplies.

Jan 1, 1962

By John H. Schloen

Copper refineries are constantly looking for methods to upgrade their plants to reduce refining costs and to improve the purity of their electrolytic cathodes at the same time that the purity of the anodes they refine is being lowered by the rehabilitation of reverberatory furnace smelters to one of the direct smelting processes. The comments given below are based on the answers to the questionnaire returned bf the 36 copper refineries that represent 66% of the western world s refining capacity. Eleven refineries employ some form of uniform weight anade casting, e.g., Outokumpu, Contilanode, Mitsubishi, Lurgi, or Hazelett. This type of anode casting presents the best possibility for improving cathode purity. The cathode press of Phelps Dadge can improve current efficiencies and cathode quality. The press is used on first-run cathodes, after 48-60 hours, on half-cells at a time without interruption of the cell current. One refinery interrupts current for sever.al hours to allow the anode slime to settle before the, cathode pressing. The cathode press is now used at eight refineries. Apart from periodic reverse current (PRC), it is not expected that current densities will be increased. Thirty refineries, using direct current, average 231 amps/M, with a low of 178 and a high of 350. Five refineries use PRC at an average of 338 amps/M, with a low of 290 and a high of 380. Current efficiencies are good at an average of 94%, with a low of 88% and a high of 99% for the 34 refineries that reported. It must be remembered that the cycle efficiency with PRC is about 93%., so that the effective current efficiency with PRC would be only .94 X .93 or 87% However, PRC should be considered seriously for refinery expansions because it can save about 25% on capital costs.

Jan 1, 1987

By E. D. Gardner

This is one of a series of papers written for the consideration of operators of small gold and silver mines in the West. The paper discusses smelting schedules, general smelting practices that have a bearing on rates, and the reasons for penalties or credits for certain constituents of ores. Crude gold and silver ores generally are shipped to smelters only when milling facilities are not available; however, high tailing losses in milling a high-grade or refractory ore or low smelting rates because of the fluxing value of an are may make direct smelting more economical.

Jan 1, 1936

By D. B. Dow

The presence of sulphur compounds in petroleum and its products is, generally speaking, undesirable, and the problems involved in removing such compounds are of great importance to the petroleum refiner and to the manufacturer of gasoline. There are several types of these compounds which are dissimilar in physical and chemical characteristics, as evidenced by different objectionable features which they exhibit, and special treatments have been developed to meet conditions existing in various products. This paper deals with the treatment of natural-gas gasoline for the removal of certain sulphur compounds which, if not removed, impart on objectionable odor and in addition badly discolor the product. The presence of this particular type of sulphur compounds is detected by the "doctor" test.* In some instances natural-gas gasoline is purchased on "doctor" test specifications, and the ordinary purchaser, while not buying on "doctor" specifications, is insistent in his demand for a water white product. Gasoline which fails to meet the "doctor" test, if not received by the buyer within a few weeks after time Of manufacture, may be "off color" enough to warrant a deduction from the market price.

Jan 1, 1923

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By E Forbes, G V. Franks

"This study investigates the dual function of a temperature responsive anionic co-polymer of poly (N-isopropyl acrylamide) (PNIPAM) as a selective flocculant/flotation collector. PNIPAM is used for separating hematite from 50:50 mixtures of hematite and quartz, at a variety of particle sizes. The performance of PNIPAM in this system is compared to that of conventional flotation collectors: sodium oleate and sodium dodecyl sulfate. The results of the study demonstrate that anionic PNIPAM used at 50¦C (above the lower critical solution temperature (LCST)) is the most effective flotation collector for hematite particles in the size range between 10 and 20 ¦m. This is attributed to the increased probability of both particle/bubble collision and particle/bubble attachment through the formation of hydrophobic hematite aggregates. Anionic PNIPAM used at 50¦C also produced the highest hematite recoveries for very fine hematite particles (circa 1 ¦m). However this recovery was completely unselective. This lack of selectivity is partially attributed to the activation of quartz particles by PNIPAM, but is thought to mainly occur as a result of entrapment of quartz particles within the matrix of hematite aggregates.CITATION:Forbes, E and Franks, G V, 2013. Selective separation of hematite from quartz by flotation using a temperature responsive polymer, in Proceedings Iron Ore 2013, pp 381-390 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013