Search Documents

By H. K. Work

THE Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of steelmaking are partly economic and partly metallurgical.' In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect-it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Bessemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (I) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. THE CONTROL PROBLEM In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to 1706°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous days burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the day, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By Howard A. Meyerhoff

IN western Argentina, in the Province of Mendoza and the Territory of Neuquén, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina's limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina's fuel problem. CHARACTER OF SOLID BITUMENS The solid bitumens of Mendoza and Neuquén are petroleum derivatives, as is indicated by the following ultimate analysis: [CONSTITUENTS PER CENT Hydrogen6.8 Carbon82.4 Nit.rogenI.6 Oxygen2.7 Sulphur2.2 Ash4.3 100.0] In physical appearance they bear a close resemblance to coal and are commonly called carbón. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-conchoidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquén. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens, are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Esperanza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1947

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

IT is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references 1 to 4. Investigations on the properties at elevated temperatures are few, however,5-7 and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. As is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hardening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During [TABLE I.-Sources of Materials Used in the Testing Program MATERIAL ORIGIN AND TREATMENT 24S-T Alclad.... From Lockheed stock. 24S-RT Alclad... Direct from mill. 24S-T80 Alclad.. 24S-O Alclad from Lockheed stock, solution-heat-treated (925°F., water quench) and aged at 375°F. for t0 t % hour. 24S-T8I Alclad.. 24S-T Alclad from Lockheed stock, plant stretched up t0 I per cent and aged t0 ± % hr. at 375°F. 24S-T86 Alclad.. 24S-RT Alclad from Lockheed stock aged 534 ± 34 hr. at 375°F. 6IS-W (bare).... From Lockheed stock. 6IS-T (bare) 6IS-W (bare) from Lockheed stock aged 8 hr. at 350°F. XB7SS-T Alclad. From Lockheed stock.] the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "overaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: I. The higher the temperature, the more rapidly is the fully aged condition attained.

Jan 1, 1945

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By John E. Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverberatory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustion will take place

Jan 1, 1938

By R. E. Steiner, A. F. Weinberg, R. J. Van Thyne

Uranium solubility in molten bismuth was determined in the temperature range 350" to 600°C, varying from 0.09 wt pct to near 2 wl pct, respectively. Zirconium and magnesium, simulated fission products, and sodium were found to increase or decrease uranium solubility in bismuth in the temperature range 370° to 420°C, depending upon the addition or temperature. Data were obtained by both chemical analysis of samples obtained by filtration from saturated melts and by measurement of the variation of electrical resistance with temperature. IN a study for the United States Atomic Energy Commission, a Liquid Metal Fuel Reactor Experiment (LMFRE) was proposed in which a solution of uranium dissolved in molten bismuth served as both the fuel solution and the primary coolant. It was proven necessary to add other elements to this solution for certain desirable properties: 1) zirconium acts to prevent reaction of the fuel solution with the graphite core (which would result in the formation of uranium carbide) and also to inhibit mass transfer of iron and chromium from the walls of the reactor tubing to cold spots resulting in blockage; and 2) magnesium acts as a deoxidant and prevents loss of uranium. In addition to these intentional additives, other elements entering the solution are: 1) fission products which are a by-productof reactor operation, 2) sodium (the secondary coolant) through possible small leaks in the heat exchange system, and 3) iron and chromium from the container walls. Each of these elements may affect the solubility of uranium in the fuel solution. Since the concept of this reactor is based upon a liquid solution, the relatively low solubility of uranium in bismuth will dictate the minimum temperature at which the reactor heat exchanger can be operated. The solubility of uranium in liquid bismuth and the effect of some additives on this solubility have pre- viously been investigated1-' (more recent results6" became avaliable after initiation of this investigation). However, some discrepancies between the various results have been noted, and also the cumulative effect of the several additions or impurities was not known. This investigation was commenced to obtain definitive results. MATERIALS Analyses of the materials used are presented in Table I. Although ostensibly of extreme purity (99.999 wt pct), the bismuth was found to contain a significant amount of impurities, probably oxides. Except for determination of the binary system, Bi-U, prior to use all bismuth was hydrogen-refined and

Jan 1, 1962

By E. W. Davis

IF the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indica-tions that this new process may make commercially possible the manu-facture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to mag-netite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe2O3) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red tempera-ture in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900° F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1936

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By Otto H. Henry, J. J. Cordiano

THOUGH powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. PURPOSE OF INVESTIGATION Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: I. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1945

By A. H. Daane, J. J. Hanak, F. H. Spedding

IN the study of the rare earths at the authors' laboratory, methods have been devised for preparing pure rare earths and many of their properties'- have been determined. Very little information is found in the literature on the properties of europium metal, which is the scarcest of the naturally occurring rare earths. Since we have recently prepared europium in appreciable quantities, we are in a position to describe the method of preparation and some of the properties of this metal. Metallic europium was first prepared by Klemm and Bommera who heated a mixture of potassium and EuC1, in vacuo, and obtained a mixture of europium metal and KC1. Trombe4 electrolyzed a molten salt bath containing NaC1, KC1 and EuC1, and collected the europium in a molten cadmium electrode as a cadmium alloy. The cadmium was subsequently removed by distillation but the properties of the residue indicate that pure europium was not obtained. McCoy attempted to prepare europium by distilling mercury from europium amalgam, but the stability of the Eu-Hg intermetallic compounds prevented a complete separation of the two elements. The preparation of very pure europium was suggested by previous work in this laboratory1,4 in which ytterbium and samarium were prepared by heating the respective sesquioxides with lanthanum metal turnings to 1450°C in vacuo and distilling ytterbium and samarium from the mixtures. Subsequently, small test experiments showed that europium also could be prepared by this method. A more detailed version of this method was used in the work described in this paper. Klemm and Bommer3 found by X-ray analysis that the metal had a body-centered cubic (bcc) structure with a lattice constant a, = 4.582 ± 0.00A (converted from kX units), with a bulk density of 5.30 g per cu cm. They found europium to be weakly ferromagnetic. Spedding, et al,7 found a,, to be 4.606 ± 0.001A. Barrett' showed that the bcc structure persists throughout the temperature range 5 to 3000K with a, at 5, 78, and 300°K being 4.551 ± 0.003, 4.551 ± 0.004 and 4.577 ± 0.001A, respectively. Trombe1 described europium as being iron gray, malleable, about as hard as neodymium and not attacked by cold water. He estimated the melting point to be between 1100 and 1200°C. Previous work in this laboratory indicated that the pure metal corrodes rapidly in air and reacts with cold

Jan 1, 1959

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The properties of quenched Ti-Fe alloys have been correlated with their microstruc-tures. For specimens quenched from equilibrium in the a-ß field, the dominant micro-structural variable is the a-ß ratio. A comparison of specimens having equiaxed a-ß structures with those having acicular a-ß structures shows that the equiaxed specimens have better tensile ductility, but lower impact resistance. There is evidence to show that specimens with acicular structures reach equilibrium in the a-ß field more rapidly than specimens with equiaxed structures. Both strength and ductility are lowered by heat treatments below 700°C. IN previous work,1, 2 certain principles of the physical metallurgy of a-ß titanium alloys have been evolved. Most of these principles have been based on data obtained on alloy systems which undergo no eutectoid reaction, or in which the eutec-toid reaction is so sluggish as to be inoperative. The alloy systems previously studied included the Ti-Mn alloys, with and without a-stabilizing additions, and the binary Ti-Mo alloys. The most important of these principles are: I) The compositional factors which affect mechanical properties are solid solution strengthening, the martensite transformation, and instability of

Jan 1, 1957

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.' Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953