Search Documents

By M. C. Ruiz

This work outlines the results of leaching studies on a copper concentrate containing chalcocite (Cu2S) and digenite (Cu9S5) with an acid saline solution of cupric chloride oxygenated at ambient pressure. The variables studied included the stirring speed, concentration of cupric ions, concentration of HCI, concentration of chloride ions, oxygen flow rate, temperature and time. The leaching system was found to be very effective for the dissolution of the concentrate. Over 95% of the copper was dissolved in 30 minutes with negligible dissolution of iron. The dissolution of copper increased with the stirring speed up to about 400 rpm and depended little on the total chloride concentration. The oxygen flow rate affected the dissolution of copper only below 0.1 1/min. The concentration of HC1 did not influence the dissolution providing its was sufficient to avoid the precipitation of copper oxychloride. The study of the effect of the temperature showed a maximum in copper dissolution around 90 "C

Jan 1, 1997

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By Maria Salazar-Villalpando, Todd H. Gardner

"Efficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). Hexaaluminate catalysts prepared at NETL may represent a product that can be utilized for the conversion of CO2 to syn-gas. In this work, transition metals dispersed in barium hexaaluminate have shown to be promising new catalysts for dry methane reforming. In this investigation, a series of BaNixAl12-yO19-d catalysts with varying Ni content were prepared by co-precipitation followed by calcination at 1400°C. CO2 reduction by dry methane reforming was carried out to determine catalyst performance as a function of temperature and carbon formation was also quantified after the reforming tests. Results of catalysts characterization, dispersion and surface area, were correlated to catalytic performance.IntroductionEfficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). The dry reforming reaction has been known for a long time. Recent publications have reported studies over several catalysts. For example, the CO2 reforming of CH4 over mesoporous nanocrystalline zirconium powders (ZrO2–3%M2Ox; M: Ce, La and K) at 700ºC have shown methane conversion up to 60% (1). Similarly, the effect of Ni content (1–12 wt%) on the surface and catalytic behavior of bimetallic PtNi catalysts supported on ZSM-5 for reforming of methane with CO2 has been studied and report shows a maximum conversion of 16% and catalyst deactivation was observed during the first hour of time on stream (2). In another report, (3) Ni/a-Al2O3 catalyst was tested for syn-gas generation at 750ºC. The maximum methane conversion was 25%."

Jan 1, 2008

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By José Antonio, Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo, Antonio Ernandes M. Paiva

"The production of alumina from bauxite using the Bayer process generate 1.25 ton of the residue known by red mud and 460 kg of CO2 per ton of alumina.The direct use of exhaust gases from the alumina refineries to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing the reactivity of red mud and sequester approximately 15% or 67 kg of CO2 per ton of alumina.This paper shows the reaction of a suspension of bauxite residue-water with a simulation of the calcinator exhaust gases of the refinery. The influence of the temperature and the ratio water red mud is also analyzed.2 IntroductionThe production of millions of tons per year of alumina around the world generates around 1.25 tones of the residue known as red mud and 0.4 ton of CO2 per ton of alumina . The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity is considered dangerous and currently there is no operating process capable of reuse all the material at any refinery. These lakes after filled of solid material eventually have the surface revegetated. Otherwise will need monitoring for decades and remain as an environmental passive. The search of a industrial process that combine the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of use in large scale in a economically viable way is the main objective of this work.The use of the exhaust gases of the refineries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester million of tones of CO2 plus other gases like SO2 [7] and NOx.This project main objective is to study the reaction of the CO2 with the Bayer process residue in order to obtain the basic parameters to design an equipment capable of process this reaction on a pilot scale. With this objective compositions of red mud on spray were processed with flow of gas containing CO2 at different temperatures and with concentration similar to the exhaust gases of the calcination process of the refineries. With the results, basic concepts of a pilot scale equipment were evaluated.A revision of the work already done on this type of residue were done [3, 9, 10]. Alternatives and potential barriers on chemistry and environmental fields were discussed. With the objective of industrial application the potential use of these materials were evaluated through the pH control, mass balance and x-ray diffraction."

Jan 1, 2010

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By H. B. Comstock

This paper reviews the trends in supply and consumption of the principal magnesium compounds in the United States in relation to domestic requirements and world resources. The data are confined to these principal magnesium compounds: Magnesium chloride, magnesium hydroxide, precipitated magnesium carbonate, and magnesium oxide (commonly referred to as magnesia). The properties and uses of magnesium compounds are shown in various chapters of' the 2nd edition of Industrial Minerals end Rocks. 3/ The third edition of this reference is in preparation. A more recent description of properties, uses and sources of magnesium compounds appears in a Bureau of Mines publication.4/ The American Iron and Steel Institute and the Refractories Institute have published comprehensive data on the properties and uses of basic refractories. Many magnesium compounds are prepared by the producers to meet specifications set by individual consumers.

Jan 1, 1960

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By R. K. Agarwal

In this paper a simple three-layered medium is considered. A circular hole is centrally located in the intermediate layer. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of [the] intermediate layer and [the] hole diameter. A comparison of stress the distribution and procedures for preparation and testing of [the] model are given. The potential of the technique is outlined.

Jan 1, 1968

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By Gabriel Riveros, Ariel Balocchi, Andrzej Warczok, Daniel Smith

Blister copper from converting of copper matte is processed by fire refining prior to electrorefining. The fire refining consists of two steps: copper oxidation with impurities slagging and copper reduction. The classical batch process is carried out in vascular or reverberatory furnaces called anode furnaces. A new process for continuous copper fire refining has been proposed. The copper flows through two reactors in cascade, where is oxidized and reduced. The flow of a liquid copper through a ceramic packed bed increases the surface area and the rate of oxidation as well as the rate of reduction in the packed bed of charcoal. Mathematical modelling allowed for the design of a laboratory scale demonstration installation and industrial-pilot installation in Hernan Videla Lira Smelter (Paipote). The results have demonstrated the process feasibility and flexibility in operation.

Jan 1, 2009

By Enderson Silva Gomes

A PRAXAIR é uma das três maiores empresas de gases industriais do mundo, com atuação em mais de 40 países e fortemente atuante na indústria siderúrgica. A PRAXAIR possui experiência para fornecer produtos e serviços para todos os tipos de siderúrgica. No Brasil, a PRAXAIR é a controladora da White Martins, maior empresa de gases industriais da América do Sul, presente em nove países do continente. O presente trabalho tem por objetivo mostrar os benefícios do Stove Oxygen Enrichment (SOE), ou seja, o enriquecimento do ar de combustão (comburente) dos fornos regeneradores de altos fornos, visando atingir economias de combustível. O enriquecimento do comburente permite que combustíveis de menor poder calorífico sejam utilizados em substituição de combustíveis de maior poder calorífico, tornando-se disponíveis para aplicações mais nobres dentro da siderúrgica, como a laminação e a geração de energia elétrica. Outro aspecto importante é a redução da queima de combustíveis que antes eram descartados no flare, reduzindo as emissões de carbono para a atmosfera.

Oct 30, 2017

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By AIME AIME

THE United Electric Coal Companies, operating large strip mines at various points in Illinois, pioneered in developing and perfecting the strip method of mining coal by use of large shovels and drag-lines. Coal stripping was first started on the properties owned by this company near Danville, Ill., in 1885. The first mechanical' excavating machine used for the purpose was really a dredge minus the hull, which had been purchased from the Marion Steam Shovel Co. It was erected on a wood frame supported by wheels and was referred to as a dry-land dredge or stripping machine. Wood was used throughout in the construction of this primitive excavator, even for the boom which was 50 ft. long. A single-cylinder vertical steam engine furnished power to hoist the %-yd. dipper arid swing the boom. 400 cu. yd. of overburden moved in a day was a great record.

Jan 1, 1936

By Frances H. Clark

IN a concern with the varied interests of the Western Union Telegraph Co., where practically all types of metals, both ferrous and nonferrous, are utilized, many types of failures of materials occur. These have to do not only with outside plant construction, such as corrosion and fatigue of line wire and cable, but also with inside plant equipment operating at such high speeds that rapid deterioration of metal. parts due to fatigue and wear results. Both corrosion and fatigue affect the life of copper wire so its normal life in any particular locality is largely dependent on the atmospheric conditions. Tensions vary widely owing to changes in temperature and ice and wind loadings and the wire is Subject to a great range of vibration caused by wind gusts aril vibration front trains or other heavy vehicles transmitted through the earth. High frequency low-amplitude vibrations are sometimes audible as singing in the wire. The other extreme is the vertical slashing or dancing of the wire observed during severe storms where amplitudes of 9, ft. or more at low frequencies have been observed.

Jan 1, 1942

By Myron Read

DURING the past 25 years, mining engineers have seen the development of a multitude of specialized engineering curricula in the mineral industry field. Bachelor degrees are now !ranted in the fields of mineral dressing petroleum engineering, geological engineering, fuel technology, and many others. These fields were all, previously considered to be part of a mining enginieer's work and elementary phases of them were included in mining engineering curricula. Their emergence has left some mining engineers with the fear that nothing will he left for a purely mining engineer to teach, or that mining engineering graduates will be unable to complete in any of these fields with the more specialized students and thus will have neatly restricted employment opportunies. A secondary reaction has been that if students who began to say that the pining engineering curriculum taught everything but mining, since so many of :he subjects that had always been udedAuded in the mining engineering curriculum now were fields in their own right.

Jan 1, 1946

By Tengfei Qi, Liqiang Fan, Huiqing Tang

A new method to process the oolitic high phosphorus iron ore for phosphorus removal has been proposed in this research. It is an integration of direct reduction and melting separation with carbon-containing pellets prepared using biomass char. Experiments of direct reduction were preceded using a tubular furnace and three parameters were investigated and they were reduction temperature, biomass char adding ratio(molar ratio of carbon to oxygen） and atmosphere. Results show that the optimum condition is of reduction temperature is 1373 K, biomass adding ratio 0.9, PCO2/PCO 1.0 and reduction time 15~25 min. Under this condition, the reduced briquettes with a metallization of 75.0~80.0 % and a residual carbon content of 0.69~0.11 wt% could be obtained. Subsequent melting separation experiments were conducted using a Si-Mo high temperature furnace. Results show metal with phosphorus content of about 0.4 mass% could be obtained from the reduced sample.

Jan 1, 2015

By Onuralp Yucel, Ahmet Turan, Murat Alkan, Hasan Ozer

SHS (Self-propagating High-temperature Synthesis) is one of the important methods to synthesize B4C powders. The process contains the reaction of boron oxide powders (B2O3) with magnesium reducing agent and carbon black carburizer. SHS products are leached in HCl media to purify synthesized B4C powders in the following step. In the present study, effects of various functional additives (KClO3, KHSO4, MgSO4.7H2O, NaCl, MgO and Na2SO4) in the SHS stage were carried out. Various proportions of the additives were mixed with the initial SHS charge mixtures. Two different molar ratios were employed in the initial SHS mixtures as 1:3:0.8 B2O3:Mg:C and 1:2.5:0.8 B2O3:Mg:C. After the SHS step, HCl leaching process was applied to the SHS products. Filter cakes were dried and characterized by using X-Ray Diffraction Spectroscopy, BET and chemical analysis techniques.

Jan 1, 2015

By Linfeng Zhou, Yuanbo Zhang, Rong Sun, Guanghui Li, Zhiwei Peng

The volatilization behavior of rhenium in the process of oxidative roasting of a molybdenite concentrate with 43.55 wt.% Mo and 321 g/t Re is explored based on identifying the relationship between volatilization of sulfur and rhenium. The results show that rhenium volatizes after sulfur and precise control of operating variables plays an important role in separating rhenium from molybdenite concentrate. When the roasting parameters are optimized as follows: roasting temperature 600 oC, roasting time 2 h, roasting atmosphere air, the volatilization rate of rhenium reaches 89.26%. In the process of solidification roasting, the volatilization rate of rhenium decreased almost to zero when the ratio of slaked lime/molybdenum concentrate was 10% excess to the stoichiometric requirement at 600 oC for 2 h.

Jan 1, 2016