Search Documents

The Rio Tinto Iron Ore group currently estimates grade attributes for mineral resources using ordinary kriging (OK). OK produces a smoothed globally unbiased estimate, but does not capture local variability, which can have significant impact on mine planning and scheduling. The dimensions and the multivariate nature of iron ore deposits make point simulations of whole deposits impractical. With a direct block simulation method the size and speed limitations of point simulations can potentially be overcome, resulting in a viable method for capturing local variability and for providing risk measures into the mine plan and schedules. Some iron ore deposits are highly folded (post mineralisation) and require preprocessing using an unfolding algorithm to properly define the continuity parameters and directions of anisotropy before simulation can proceed. Block co-simulation proceeds in unfolded space and since mine planning require a block-model with regular block-sizes; a regular block-model is unfolded first. This paper discusses a block co-simulation approach that can be used to simulate the irregular blocks resulting from the unfolding process. A section of an iron ore deposit is used for testing the block co-simulation algorithm and the simulation results are compared against the Isatis direct block simulation method. Available blasthole data is also used to validate the behaviour of the block co-simulation algorithm.

Sep 26, 2011

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989

By E. Saez, M. Bellet, T. Coupez, O. Jaouen

"The paper presents a 3D finite element solver for non-steady state fluid flow. The thermomechanical simulation package REM3D® has been initially developed to model Stokes' flow for polymer injection. The mechanical module is based on a Eulerian velocitypressure formulation. The spatial discretization uses P 1+IP1 tetrahedral elements. The front tracking module consists of the resolution of a transport equation, thanks to a space-time discontinuous Galerkin formulation. It includes mesh adaptation, which permits a dynamic refinement at the front, thus controling the numerical diffusion. The same approach is used to solve heat transfer. In this paper, we focus on the specific adaptations done to treat Navier Stokes flow. The treatment of inertia is detailed, as well as the implementation of sliding conditions at mould surface, using conservative normals. Industrial applications are presented.IntroductionThe study of the mould filling stage in casting processes requires the ability to simulate complex non steady-state three-dimensional flows. Most commercial software use the volume of fluid (VOF) method, associated with a Eulerian formulation, see for instance the series of conferences ""Modelling of Casting, Welding and Advanced Solidification Processes"" [1-3]. The VOF method [4] consists in solving the conservation equation dF / dt = 0 for a variable F - the volumic fraction of fluid - whose value is 1 in filled regions and 0 elsewhere. Two fluids are actually considered: the molten alloy and a gas in the empty regions. This method suffers generally from numerical diffusion in the resolution of the free surface tracking equation, which is of pure advective type. The precision of the computation is then strongly dependent on the mesh density. Since the mesh is fixed (Eulerian formulation) this implies that in case of complex flow the user must have a priori a fairly good idea of the flow characteristics in order to capture properly the critical features of the flow. In addition, the method can hardly handle the discontinuity of the material viscosity at the interface. To prevent this difficulty, the viscosity value is smoothed around the interfuce, adding once again some inaccuracy. Since the value F = ½ is supposed to represent the free surface, it results in a smeared fluid surface. An alternative to the fixed mesh methods are the methods in which the mesh covers the fluid domain only, as proposed by Navti and Lewis [5-6], or Gaston and Bellet [7]. Based on updated Lagrangian schemes, they must be associated with an ALE formulation (arbitrary LagrangianEulerian) in order to reduce the number of full remeshing operations."

Jan 1, 2004

By D La Rosa, D Bennett

"Exploration drill core provides for a number of standard measurements essential for determining the viability of a new mine or the extension of an existing one. Rock lithology and alteration can be visually determined and grade measured from the half core. Geotechnical parameters such as rock strength and structure can also be measured. Using suitable proxies, these metrics can then be used to estimate run-of-mine (ROM) particle size. In combination with comminution test results, these can subsequently be used to design comminution circuit configurations and estimate their performance.The Frieda River Project drill core for the large Horse-Ivaal-Trukai copper-gold porphyry deposit was unusual due to a late stage gypsum-anhydrite stockwork event that overprinted much of the deposit. Above the base of the oxidised zone, which closely matches the water table, gypsum and anhydrite has been leached out, effectively removing the glue holding the rock mass together. As a result, much of the rock above this gypsum-anhydrite surface is fragmented and gravel-like in texture, while the material below this horizon is typically uniform and competent.Large volumes of the orebody above the gypsum-anhydrite surface are expected to need minimal or no blasting for efficient excavation. In addition, the fragmented nature of much of the material was expected to reduce comminution specific energy as it already appears as though it has been crushed. While this was expected to have positive impacts to the operation, the lack of standard geological logging methods available to accurately define the degree of in situ fragmentation led to difficulty in gaining certainty over the ROM product and grinding circuit feed size distributions.Using the extensive library of core photos for the project, a novel method using image analysis techniques to take both the intact core and gravel into account to predict ROM fragmentation was developed. In addition, existing point load test data was used to infer the strength of the rock and its impact on the blasting, crushing and grinding processes. The novel approach allowed development of ROM size distribution data and improved certainty in the results of comminution circuit designs.This paper describes the methodology undertaken in detail, and discusses the results obtained.CITATION:Bennett, D and La Rosa, D, 2016. The Frieda River Project – a Novel Approach to Analysing Exploration Drill Core: How Broken is Broken?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Barrick Gold Corporation is the gold industry leader, with 25 operating mines and a pipeline of large, long-life projects located across five continents, in addition to large land positions on some of the most prolific mineral districts. Barrick's high level of commitment to sustainable economic development and environmental stewardship was recognized by Dow Jones Sustainability Index (DJSI) - World, for the third consecutive year in 2010. The potential for adverse environmental effects from acid rock drainage (ARD) and metals leaching (ML) and their financial implications for Barrick are key considerations in our environmental assessment and business development processes. Barrick's membership in the International Network for Acid Prevention (INAP) reflects the importance of these issues to our business. INAP's development of the Global Acid Rock Drainage (GARD) Guide (a best practices guide for acid rock drainage prevention) provides Barrick with an important tool to assist in the assessment of environmental and financial risks from ARD and ML associated with our planned and ongoing mining operations (INAP, 2009). In this paper we will discuss how Barrick incorporates the GARDGuide and its principles for ARD and ML prediction and prevention in our business development processes and the management of our operations. The GARDGuide serves as a key reference for our project environmental assessments and as a common link between our projects and operations management, consulting specialists, permitting and regulatory authorities and the public. We will discuss how the GARDGuide is being "syndicated" throughout Barrick as a standard of practice and present a case study of how it was used in a recent Barrick Business Development Project.

Jan 1, 2011

By Chris McKee

Quartz has been of interest in occupational health for years because it can cause silicosis after prolonged exposure. New OSHA regulations (Air Contaminant; Final Rule) list perlite as a nuisance dust. They conclude that perlite is nontoxic when air-borne total particulate concentrations are 15 mg/m3 or below and when quartz content is less than 1% crystalline silica. OSHA has established an 8-hour PEL of 15 mg/m TWA for total perlite dust containing less than 1% quartz. OSHA has established a 5 mg/m3 TWA PEL for respirable perlite. These limits will protect workers from significant risk of eye, skin, or other physical irritation. This regulation is based on a Group 2A classification as a probable carcinogen in humans, at the 0.1% crystalline silica level, by the International Agency for Research on Cancer (IARC 1987a, b). IARC found sufficient evidence for carcinogenicity of crystalline silica in animals and limited evidence in humans. Perlite is not listed as a carcinogen by OSHA or the National Toxicology Program.

Jan 1, 1990

By D. Haraguchi, S. Izawa, C. Tokoro, S. Owada

"Arsenic is widely known as a toxic element for humans, animals and plants. Because of more stringent wastewater standards not only in Japan but also around the world, research for appropriate and efficient treatment method for arsenic is becoming increasingly important. Coprecipitation or adsorption process using ferrihydrite is widely implemented for dilute As(V) removal from wastewater. In this study, the sorption mechanism of dilute As(V) with ferrihydrite in coprecipitation or adsorption process was investigated. To accomplish this, we conducted batch experiments of coprecipitation or adsorption and compared these results for sorption isotherm and zeta potential. These experimental results showed that sorption mechanism in coprecipitation process depends on the initial As/Fe molar ratio; simple twodimensional adsorption onto the surface of ferrihydrite when the initial As/Fe molar ratio was < 0.4, and some three-dimensional uptake with ferrihydrite when it was = 0.4. We also evaluated the sorption mechanim by analysis of X-ray diffraction (XRD) and X-ray Absorption Fine Structure (XAFS). XRD or XAFS spectra showed that surface precipitation of amorphous ferric arsenate was formed when the initial as/Fe molar ratio was = 0.4, beyond the thermodynamic bulk precipitation range for ferric arsenate.INTRODUCTIONArsenic is toxic to animals, including humans, and long-term exposure to arsenic via drinkingwater causes cancer of the skin, lungs, urinary bladder, and kidneys, as well as other effects on the skin such as changes in pigmentation and thickening (Ghosha et al., 2008). Elevated levels of arsenic are often present in the environment as a result of the weathering and dissolution of minerals as well as in response to numerous anthropogenic sources including the discharge of mine wastes, coal fly ash and the use of pesticides that contain arsenic (Nriagu, 1994; Singh et al., 2007). Indeed, the potential for arsenic exposure affects many people, as evidenced by several million people in Bangladesh and India being at risk of exposure via drinking water obtained from contaminated groundwater sources (Ahmed, 2001).Acid mine drainage (AMD) containing arsenic is a global environmental problem (Dold, 2008; Liang and Thomson, 2008) that also affects Japan, which has many abandoned or closed mines that have been generating AMD for the last few decades (Masuda et al., 2008). Several such facilities in Japan produce AMD containing dilute concentrations of arsenic that exceed Japanese effluent standards (0.1 mg/dm3) (METI, 2006). For example, AMD from the abandoned Horobetsu sulfur mine, the largest AMD source in Japan, contains approximately 10 mg/dm3 arsenic."

Jan 1, 2012

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By Raghoottma S. Pandurangi, Mohindar S. Seehra

"The interaction of amorphous 1ilica particles with several hydrogen bonding agents (H2O, C2H5OH, C7H2NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy. It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction or surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C7H2NO > C2H5OH > H2O. Index Headings: Silica; Surface vibrational modes; Photoacoustic spectroscopy; Hydrogen bonding agents.INTRODUCTIONThe use of m spectroscopy to study the adsorption on solid surfaces is well documented in the literature.1 2 For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1• Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-5 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity, 7- 9 catalysis, 10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8NO), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by m spectroscopy, and Knozinger16 and Rouxlet and Semples11 have used transmission m spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties. In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18•19 Moreover, according to a recent paper, 20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry. In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H50H, and H20) with the silica surface by monitoring changes in the surface m modes. Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents. Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16•17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification. Details of this work are given below."

Jan 1, 1990

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By R. Heikkilä

Fluent information exchange between different work phases, software and systems used in infra construction is a key for successful execution of infra construction projects. Open and publicly available information formats with the determined data models aim to facilitate the interoperability between different software and systems developed by competitive vendors. While building and construction industry has developed and used IFC format for years, infrastructure sector has just recently started to target clear efforts on the development of open information formats for infra construction processes. In the paper, a new Inframodel3 extension just developed in Finland and based on the LandXML1.2 international standard is to be introduced. The aim of the Inframodel3 was set to meet the requirements of information transfer needed especially between BIM based design software, measurement systems and 3-D machine control systems used in road, railway and watercourse construction projects. Some test results are reported and evaluated in the paper. In the field of bridge engineering, the IFC format and IFC Bridge extension have been tested and evaluated in Finland. The results from the experiments show and verify as well the applicability of these open formats to the information exchange requirements in bridge engineering. The current limits for open information transfer of these formats are shown. The active co-operation with the International Building SMART Organization has led to the achieved status and position for both the Inframodel3 and IFC Bridge formats and hence the continuing international support provided by Building SMART.

Aug 1, 2013

By Morgan Schauerte, Laura Raimondi, Mariel Palomeque

Executives in the mining industry are facing dramatically changing market expectations on reporting and transparency regarding the environmental and social impacts of projects, supply chains and products. Companies increasingly need to disclose the governance procedures they have in place to ensure communities, investors, employees, and Indigenous partners are effectively managing social and environmental risks. These disclosure requirements begin during exploration and carry through to all stages along the project life cycle. This type of environmental, social and governance (ESG) disclosure is referred to as ESG performance by the investment community. ESG is not a new concept, and it builds on and is intertwined with many concepts such as corporate sustainability, corporate social responsibility, eco-efficiency, triple bottom line thinking, life cycle management and many others. This paper will explore how mining companies can develop a credible ESG governance approach and strategy that will reduce risk, open opportunities, and create value. This paper will summarise ESG trends and drivers, discuss the economics and investors’ perspective towards ESG, and outline leading ESG standards and guidelines of interest to investors, regulators, communities and other stakeholders. Linkage of ESG to global sustainability efforts such the United Nations Sustainable Development Goals and Global Compact will also be addressed.

Jan 1, 2023

By F. Karakas

Water based paint formulations consist of some industrial minerals with quantities varying from 20 to 50 %. Quality of paint is directly related to these minerals used as pigment or filler in the production. Titanium dioxide is the most important and expensive pigment in paint formulations. Other minerals such as calcite and calcined kaolin are used as filler and mainly as a substitute for TiO2. Consequently, particle-particle interactions including adsorption, coating and size distribution of pigment mixture directly affects the paint quality. In the present paper, a new type of pigment mixture for possible use in architectural water based paints was developed through grinding. The effect of different types of grinding methods on physical properties of TiO2 and calcite mixture and the quality of paint produced by these mixtures have been revealed. Three different types of mills; conventional ball mill, vibratory ball mill and high-speed attritor were used for grinding of TiO2 and calcite. Viscosity, zeta potential and particle size distributions were used to characterize the pigment mixtures obtained upon grinding. The quality of paint was evaluated by standards based on both wet and dry paints such as viscosity, density, opacity and gloss. The paint produced with the pigment mixtures prepared in vibratory ball mill and high speed attritor showed improvement in physical properties particularly in the distribution and dispersion of mineral particles. Keywords: grinding, pigment, paint, TiO2, calcite

Sep 1, 2012

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By Richard F. Hewlett

This Bureau of Mines report presents the computer programing methods and mathematics required to generate either random numbers or normal random numbers to be used for the construction of statistical probability models for simulating mineral deposits by Monte Carlo techniques . Theoretical frequency functions are evaluated as an illustration of simulation applications . Numerical and analytical methods of simulating and dissecting some complex frequency distributions are described .

Jan 1, 1964

By John Randall

It is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary first to consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size .at the right-hand side of the diagram and measuring toward the left. This is not altogether convenient and might be changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, making it less convenient for most purposes, and for that reason the method here discussed is the well-known one based on the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have noted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 1, 1918

By John Randall

IT is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless. of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary to first consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size at the right-hand side of the diagram and .measuring toward the left. This is not altogether convenient and might he changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, snaking it less convenient for most purposes, and for that reason the method here discussed is the well-known one based oil the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although .not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal. parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have rioted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series &apos;of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 9, 1917

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method&apos;s usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987