Search Documents

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By R. R. Brandenthaler

A series of open-flow tests was conducted in the Chickasha gas field, Grady County, Oklahoma, during June, 1927, under the direction of the U. S. Bureau of Mines and at the request of the Oklahoma Corporation Commission. The purpose of these teats was to determine whether or not any differences existed in the open-flow volume of a gas well when taken through well-head nipples of different diameters, and further, to establish if possible a relationship between open-flow volumes taken through well-head nipples of various diameters. The open flow of a well is the volume or quantity of gas, measured under standard conditions, that a well will produce when open to the atmosphere. There are several methods used for determining the open flow of wells; some of the methods are more suitable under certain conditions than others. The Pitot tube method is the simplest, is applicable to almost any condition, and is the one most commonly used. In the tests described in this paper no attempt was made to compare the Pitot tube method with the minute pressure measurement method or the orifice measurement method.5

Jan 1, 1928

By Santiago Garcia, Dariusz Lelinski, Devan Govender, Tyson Baker, Mads Jespersen

"In recent years, the scale-up of mechanical flotation machines has been attempted with greater frequency. In contrast, the development of rotor-stator designs has been subject to greater inertia. The rotor-stator components are integral to the operation of mechanical flotation machines, responsible for the key physical processes of solids suspension, gas dispersion and energy dissipation. Design modifications are predicated upon the dual purpose of meeting customer needs while achieving metallurgical performance objectives. Accomplishing the latter is a rigorous undertaking, typically involving the sequential application of fluid dynamics principles, prototyping, smaller-scale research screening studies and larger-scale development projects. This industrial evaluation details the final stages of the forced-air rotor-stator development process using a double-refractory Carlin-type gold ore. A bypass stream of the primary rougher feed was further classified into cyclone underflow and overflow products. Four rotor-stator treatments were evaluated using parallel flotation rows coupled with a randomized statistical design. Only two treatments are compared in this initial assessment. Metallurgical responses were measured as a function of the random variation of key machine factors. Machine characterization measurements complemented the analysis of flotation performance indicators."

Jan 1, 2014

By C Taylor, E Retz

Sequential Gaussian conditional simulation of wide-spaced exploration data has been completed in order to optimise a drilling grid at Fortescue’s Eliwana deposit. The aim of this drill grid is to improve the confidence in the Inferred Mineral Resource. A mineralised domain within the Joffre Member of the Brockman Iron Formation was selected to be tested as it makes up a large proportion of the Inferred Mineral Resource and is drilled at a reasonable spacing.One hundred realisations of Fe, SiO2 and Al2O3 grades were completed in the domain. Three realisations were selected for each analyte to represent the range of equiprobable values and a further realisation was selected to represent the truth data set. These realisations were used to flag theoretical drill holes on varying spacings and patterns. The theoretical drill holes were used to estimate into block models using ordinary kriging.These estimates were analysed and the accuracy and precision of each drill spacing was assessed. It was concluded that the greatest improvement in estimation results was noted at either a 100 m × 50 m or 50 m × 50 m spacing.CITATION:Taylor, C and Retz, E, 2015. How much do we need to drill?, in Proceedings Iron Ore 2015, pp 491–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By William B. Coker, Vladimir J. Sopuck, J. S. Fox

"Preliminary investigations indicate that organic lake sediments offer some potential for gold exploration within the Canadian Shield of northwestern Saskatchewan. It is also apparent that certain precautions must be taken.Gold is primarily related to the organic fraction of the lake sediments, which, although giving consistant Au contents to those sediments, may restrict the dispersion of Au within the lake itself. It may be necessary to carry out selective extractions on the lake sediments to differentiate between Au related to organic sequestration, indicative of hydromorphic and/ or chemical dispersion, and Au related to inorganics, indicative of mechanical dispersion.Lake sediments are probably only of use for very detailed exploration (i.e. every lake). One to three samples per lake should be appropriate, although a single centre-lake organic-rich sediment sample may be adequate in very small lakes. Each lake sediment sample should be analyzed at least twice and the analytical data carefully monitored and evaluated.The use of As in lake sediments as a pathfinder element for gold is applicable in the search for certain types of gold occurrences.Following detailed lake sediment sampling, basal till sampling can possibly be used to localize areas of potential gold with or without base metal mineralization."

Jan 1, 1982

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997

By Kyle Bartholomew, Robert McIvor

"Functional performance analysis of closed circuit grinding provides valuable insight into the two components of ball mill circuit grinding efficiency: classification system efficiency and mill grinding efficiency. Classification system efficiency isolates the combined effect of classifier performance and circulating load ratio from other circuit variables, such as ore grindability and the mill grinding environment. Optimization of classification system efficiency ensures grinding energy is applied to particles needing further size reduction and not to overgrinding. Entirely based on size distribution data, classification system efficiency precisely distinguishes subtle changes in classification system performance. Use of the functional performance equation to isolate mill grinding efficiency allows for proper optimization of the mill grinding environment by isolating confounding effects of changes in classification and ore grindability. Variables such as mill percent solids and grinding media selection can be optimized using the mill grinding efficiency subcomponent of functional performance. First published by McIvor in 1988, the functional performance equation provides a set of standardized, quantitative optimization criteria, simple and powerful, which link circuit performance to plant design and operating variables that can be manipulated. Functional performance optimization has been applied in numerous mineral processing plants globally and continues to gain acceptance as a practical means for grinding circuit optimization. In this paper, examples of derivation and industrial application demonstrate the means by which functional performance analysis dissects grinding circuit efficiency into its subcomponents allowing the reader to apply this straightforward, powerful optimization methodology at their mineral processing operation."

Jan 1, 2014

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dust escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dusthog- type bit to improve dust extraction during the critical initial phase of drilling. A twistedbody drill bit is also evaluated to determine the quantity of dust liberated in comparison with the dust-hog-type bit. Based on the results of our laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emission can also be substantially reduced. The use of a twistedbody bit has minimal improvement on dust capture compared with the commonly used dust-hog-type bit.

Jan 1, 2014

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By Miro Mihelich

The mines and prospects in the vicinity of Landlocked Bay, 25 miles southwest of Valdez, Alaska (fig. 1), were examined, mapped, and sampled in July and August 1955 as part of a comprehensive investigation by the Bureau of Mines of ore deposits adjacent to Prince William Sound. The purpose of the investigation is to establish and record the location, nature, extent, and metallurgical characteristics of copper and associated metallization in the Prince William Sound district and to indicate, if possible, those areas in which additional exploration and development may be justified. Of particular interest are the possibly numerous deposits of massive iron sulfides that were neglected during early mining operations. These deposits may constitute important reserves of sulfur and iron. At Landlocked Bay deposits of copper-bearing iron sulfide minerals have been mined or partly explored through mine workings, which are in a zone about 1 mile wide along the western side of a large overthrust fault known as the Landlock Overthrust. Eight of the principal mines along this zone were examined end sampled. Although only three of the mines have a recorded production of shipping-grade copper ore, all have deposits of copper-bearing iron sulfide minerals that are similar in occurrence. The deposits occur as lenticular masses and disseminations of chalcopyrite, pyrite, and pyrrhotite which replace crushed rock or fill cavities along shear zones in greenstones and in sedimentary rocks that are exposed between sea level and an altitude of 2,500 feet. These lenticular masses of sulfide minerals range in size from small pods to ore bodies that have been stoped to maximum widths of 9 feet, strike lengths up to 70 feet, and dip lengths as much as 350 feet. Where accessible for sampling,, the copper content of the deposits ranged from a few hundredths of a percent to over S percent; zinc, gold, and silver are present in negligible amounts. Flotation tests of a sample composited to represent typical mine-run ore indicate that 81 percent of the copper is recoverable in a product assaying 28 percent copper at a concentration ratio of 17.5 : 1. INTRODUCTION Statistical records indicate that approximately 110,000 tons of metallic copper (about 16 percent of total Alaskan production) was produced from mines adjacent to Prince William Sound during the 40-year period ended in 1938. Although the principal production was from a large-scale mining and milling operation on Latouche Island (Kennecott Copper Corp., Beatson mine), a substantial amount of the total copper was derived from direct-shipping ores selectively mined or hand-sorted from numerous other deposits in the district. No production has been made since 1938; many of the claims have long been abandoned, and mine workings are either caved or deteriorating rapidly.

Jan 1, 1957

By P Oikkonen

Sprayed concrete has played an integral role in underground rock support for nearly a century. However, concrete is also considered to be one of the biggest environmental problems in construction and mining, largely because of the high carbon footprint of cement and aggregates production. This is driving the industry to find ways to cut concrete usage where possible. Improving sustainability by cutting concrete material consumption also reduces application time and costs. Improving concrete properties can make it possible to design thinner linings, but as awareness of safety and longer design lifetimes are driving developments in the opposite direction, it is not realistic to see this as a major factor in cutting concrete consumption. More accessible solutions are focusing on layer thickness control and minimising rebound and wastage. Digital technology and innovation offer excellent tools for improving sustainability while optimising other aspects of the spraying process at the same time. A digital layer thickness control system gives near-real-time information to the sprayer operator with full coverage of the sprayed surface. This enables the operator to achieve consistent layer thickness on the first pass, in comparison to the traditional methods of overspraying with the aim of achieving sufficient layer thickness, probe drilling after the concrete has set, and respraying at a later stage if needed. Operator competence is the single biggest variable in a successful sprayed concrete process, affecting rebound and wastage levels. Unfortunately, the learning curve to become a master sprayer is quite steep and training on a real sprayer and real concrete requires a significant amount of time and money. Training in a virtual reality (VR) environment enables operator training to be carried out in a low-risk environment and provides a way of measuring performance and assessing and certifying the operators. After the VR training period, a novice nozzle operator has the basic understanding to start working on a real sprayer, and an experienced nozzle operator can benefit from the possibility of assessing their performance.

Mar 29, 2023

By Craig A. Johnson

Cyanide speciation and behavior have been examined at three active heap leach operations, three heaps undergoing rinsing, and three sites with cyanide contaminated groundwater, all in the southwestern U.S. Data from these studies demonstrate that strong cyanometallic complexes of iron and cobalt can play ?an important role in cyanide behavior throughout the lifetimes of heap leach operations. In active circuits, we find evidence that significant amounts of cyanide combine with iron and cobalt to form strong cyanometallic complexes, and that these species can be adsorbed, probably onto iron hydroxides, or precipitated as insoluble cyanometallic compounds. When spent heaps are rinsed, the release of this cyanide is likely controlled by the slow kinetics of desorption from, or dissolution of, solids that have gone largely uncharacterized. We find evidence that strong cyanometallic complexes can give rise to transient free cyanide in some settings by rapid photo dissociation where heap rinse effluent is exposed to sunlight in open channels or translucent sample bottles. Thus, these species can complicate the ,preparation of spent heaps for decommissioning, even where regulatory standards ?are based on weak acid dissociable cyanide. There is a critical need for information on the form and stability of adsorbed and precipitated cyanide in spent ore heaps, on the concentrations of strong cyanometallic complexes in mineral processing effluents -particularly the complexes of cobalt, and on the natural attenuation of iron and cobalt cyanometallic complexes in both surface and subsurface waters.

Jan 1, 1998