Search Documents

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By E. W. Filer, R. P. Smith, L. S. Darken

The solubility of nitrogen gas in purified iron and low alloy steels is determined for the y region (930° to 1350°C). The diffusivtiy of nitrogen is estimated from the rate of approach to equilibrium. The investigation of aluminum-killed steels, held in nitrogen, discloses precipitation of aluminum nitride, the solubility of which is determined. ALTHOUGH several investigations of the solu-bility of nitrogen gas in y iron have been reported, all have made use of the method adopted by Sieverts in his classic work, whereby the solubility is determined by the pressure or volume change of the gas. The agreement between different investigators* is rather poor, particularly as compared to the self-consistency of results of several individual investigators. The present report represents a portion of our investigation of the equilibrium of nitrogen and nitrogenous atmospheres with iron and steels. The method adopted in this temperature region (910" to 1400°C) consists of holding the specimen in gaseous nitrogen, quenching (or cooling), and determining the nitrogen content by direct analysis (solution in acid followed by distillation and titra-tion of the ammonia).** Up to 1050°C a 20 in. vertical wire-wound (Kan-thal) furnace was used; this was wound in three sections so that by proper adjustment of relative currents, and use of a modulator1 and a commercial controller (using a chromel-alumel control couple), a zone almost 6 in. long could be maintained uniform within a few tenths of a degree. Since the temperature coefficient of the nitrogen solubility is low, the full precision was not utilized and a variation of l° to 2" was tolerated; a variation of a similar amount also occurred occasionally between the beginning and end of the experiment. At higher temperature a vertically mounted, tubular Globar furnace and control unit was used; the zone of uniformity (l° to 2"C) was here limited to about 2 in.; fluctuations with time were comparable to those in the wire-wound furnace. Reported temperatures were measured by use of a platinum-platinum-rhodium thermocouple, which was frequently com- pared with a similar standard couple which was calibrated at the gold and palladium points and also compared with one certified by the Bureau of Standards; error from this source is believed to be less than 1 "C. Nitrogen gas from a commercial cylinder was mixed with slightly over 1 pct H by use of a gas mixer described previously.' This mixture was passed over hot copper and through ascarite and phosphorus pentoxide to remove oxygen and water vapor. The purified gas contained 1.05 pct H. This procedure was adopted to prevent the formation on the specimens of oxide film, which is well known to be nearly impervious to nitrogen; its success was attested by

Jan 1, 1952

By D C. Curry, M F. Young

Many flotation operations need to improve liberation to increase recovery, yet often plant operators are concerned that finer grinding will produce æslimesÆ with low flotation recovery. Yet simple circuits can be designed to give good liberation and excellent fines recovery. The economics of fine grinding has changed fundamentally with new stirred milling processes like the IsaMill. This has also transformed flotation design due to the clean surfaces produced in the inert grinding environment and the narrow size distribution produced by the IsaMill. Past poor experiences with æovergrindingÆ in flotation circuits was often due to the wide size distribution and the degradation of mineral surfaces produced by conventional devices using steel media, like ball mills and tower mills. The correct practice is to design both grinding and flotation together to suit the liberation characteristics of the ore. This may result in several stages of grinding and flotation, recovering mineral as soon as it is liberated, then applying further grinding energy only to those particles that still need liberation. Flotation then occurs in relatively narrow size bands and with minerals with similar liberation characteristics. Though the circuit may look more complex on paper, in reality it is far simpler to operate since each section performs predicably. Circuit design also needs to address materials handling. Finer particles affect froth handling and dewatering, but can still be easily handled by standard products with careful attention to design of launders, pumps and pumpboxes, and de-aeration before thickening and filtering. Excellent examples of designing circuits to include ultrafine grinding include Mt Isa and McArthur River (MRM). In the last decade these operations have produced over ten million tonnes of concentrate with an average grain size below 10 ¦m and above 80 per cent recovery. At Mt Isa, zinc recovery was increased by ten per cent by applying fine grinding to existing poorly liberated streams. In fact, grinding finer in the IsaMill actually improved the recovery of fine particles by ten per cent, and maximum particle flotation recovery occurs for 10 ¦m particles. A more recent example is the flotation of Platinum Group Metals (PGMs). The use of conventional ball or tower milling to improve liberation is severely limited by the impact of commonly associated chromite on classification, and degradation of flotation performance by the steel grinding environment. The ability of open circuit IsaMills to deliver a narrowly sized ultrafine product with clean mineral surfaces is transforming the design of platinum flotation circuits. The science and practice of fine-grained flotation is now thoroughly proven. The availability of the 2.6 MW IsaMill has made ultra fine grinding a practical tool for flotation plant design. It is expected to become a standard choice for future applications of both fine-grained ores and for minerals with difficult flotation characteristics.

Jan 1, 2005

By M. R. Goldick

The Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5½-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mcchanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. Ore Treated Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopy-rite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (go pct minus-zoo mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1949

By P. Chiotti, J. T. Mason

Metallographic, thermal, X-ray, and vapor-pressure data were employed in establishing the Ce-Zn phase diagram. Nine compounds and three eutectics were observed. The eutectic compositions in weight percent zinc and temperatures are 10 pct and 495"C, 37 pct and 795°C, and 56 pct and 810°C. Three of the compounds, CeZn, CeZnn, and CeZne.5, melt congru-ently at 825°, 87.505°, and 980°C, respectively; the other six compounds, CeZns, CeZns.67, CeZn4.5, CeZn5.25, CeZn,, and CeZnll, decompose peritectically at 820°, 840°, 870°, 885", 960°, and 795"C, respectively. The compound CeZn5.25 is an AB5 type with a small range of composition which lies on the zinc-rich side of the 1 to 5 stoichiometry. Zinc vapor-pressure data obtained by the dewpoint method were employed in calczilating the thermodynamic properties of both the liquid alloys and solid compounds. The data for the A critical review of the information available on the Ce-Zn system up to 1960 has been given by K. Gschneidner, Jr.' Of particular interest is the work by J. schramm2 who investigated the region between 55 and 100 wt pct Zn and reported a CeZn,, compound which decomposes peritectically at 785"C, a CeZn, compound which melts congruently at 972"C, and five temperature horizontals at 79@, 817", 840", liquid alloys were fitted to the relation from which the relation was obtained by integration. In these relations F XS is the excess partial molal free energy, N is atom fraction, and the constants c and d have the values c = (-22,000 + 7.0T) and d = 6171,000 + 74.0T). Relations for the standard free energy of formation for the solid compounds were derived from the data. At 973°K the enthalpy in kilocalories per gram-atom z)aries from —11.3 for CeZnz to —8.21 for CeZn~l and the free energy in the same units varies from —7.1 joy CeZn, to -3.82 for CeZn11. and 942°C in the region between 55 and 75 wt pct Zn. No attempt was made to identify other features of the system. I. Johnson and R. yonko3 used a fused-salt cell to measure the electromotive force between pure cerium and an alloy consisting of zinc-rich liquid in equilibrium with CeZnll. Solubility data for cerium in zinc has been reported by J. Knighton et u1 .4 Johnson and Yonko give the following equa-. tions for the mole fraction of cerium in zinc and the standard free energy of formation of CeZnll:

Jan 1, 1965

By M. R. Goldick

THE Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5 1/2-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mechanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. ORE TREATED Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopyrite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (90 pct minus-200 mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1947

By F. E. Buch

The smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The :smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pet moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pet oxide copper. The predominating minerals are chalco-cite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. General Description Flotation concentrate, containing 10 Pet moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and Spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which Prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been Set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1949

By E. C. Tveter, R. B. Tippin

The separation of minerals by heavy liquids is a standard laboratory technique which goes back at least 50 years, but commercially economic application of this principal to ore concenfration has been prevented by problems of liquid recovery. Recent investigations which demonstrate the different types of liquid-solid systems on various ores using the two major heavy liquids - methylene bromide and tetra-bromoelhane — are discussed in this article. As a result of these studies, over-all liquid recovery, and especially desorption of heavy liquid from the mineral surface, was improved by the use of surfactants as well as both thermal and mechanical energy. The examples given in the article indicate that heavy liquids which should find major commercial use in ore concentration are now available. The sink-float process using a heavy liquid medium has long been recognized as a nearly perfect method of mineral separation based on the differences in density of the minerals. The use of heavy liquid separation (HLS) offers the potential of an ore dressing method that provides the maximum possible natural concentrate grade and high recovery. In addi- tion the process requires no water, causes no waste disposal problems, and is extremely simple — the crushed ore is merely introduced into a liquid whose density is between that of the minerals to be separated. The minerals lighter than the liquid float while those heavier than the liquid sink. As such, HLS has become a standard laboratory tool but major commercial application has been prevented by the requirement for complete recovery of the heavy liquid, imposed by economics and materials handling hazards. Investigations, both in the United States and abroad, have shown that improved liquid stability as well as improved chemical engineering techniques brighten the future for HLS in ore dressing. The available commercial heavy liquids suitable for mineral separation cost from $2.00 to $20.00 per gallon1 and on this basis alone their complete recovery is economically desirable. Possibly of even greater importance is the fact that any residual heavy liquid remaining on the products could create a serious toxicity hazard. Consequently, to make the process commercially attractive requires (1) essentially complete removal of the liquid from the ore products and (2) optimum recovery of the liquid for reuse. Until recently these two stipulations have remained as obstacles but laboratory and pilot plant research now in progress suggests that these may soon be overcome. Various heavy liquid recovery systems have been proposed to meet these requirements and might be classified into one or more of the following three general classes: Solvent Wash (Fig. 1): The dissolution of the heavy liquid from the ore with a less expensive solvent,

Jan 1, 1969

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By Arthur Smith

THE Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district-the United Verde and the United Verde Extension-lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., . a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to? the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Wood chute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the . smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the vicinity of Allen Springs, at the south end of Mingus mountain and all within the boundaries of the Prescott national forest reserve.

Jan 3, 1924

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Matthew D. Meyer

SMART, an association of surface mining companies formed in 1995 to develop a coordinated approach to technology development for the mining industry, has recognized the need for the establishment of a worldwide database that continuously collects mining equipment data and provides metrics related to productivity and cost. Under the auspices of SMART, Syncrude Canada, Suncor Energy and Albian Sands Energy (three oil sands mining operations located in northern Alberta) have established a pilot project for mine benchmarking. This presentation will include a review of the pilot progress including: ???Data gathering techniques: means of collection and storage, proposed practice for data control and normalization, access to data/reports and format for data. ???Reports/analyses for individuals, across groups, within the total industry pool and publicly. ???Security and confidentiality of information belonging to identified parties. ???Sharing of best practices among members. SMART has identified two key deliverables to ensure success of the project. First, data supplied from surface mines must be validated and normalized to common definitions and then analyzed to provide participating companies with regular reports that allow them to understand their position and resultant opportunities to achieve world-class performance. This model maintains granularity of the data for each operation that can then be recombined into standard comparisons or specific indices as required. The general categories of: operating delays, maintenance downtime, standby, and scheduled downtime, have been used to frame comparisons. Second, participating companies are looking to go behind the indices to identify and share best practices that distinguish particular operations. The spirit of cooperation between the companies involved in the pilot project is meant to be a model for future expansion of the benchmarking project.

Apr 1, 2005

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By Adrian Villanueva

In this study, we compare the influence of two water soluble polymer-based organic binders added to bentonite, to form a hybrid-binder system for Iron Ore Pelletization. The kinetics of the agglomeration process and resulting properties of green pellets were analyzed, and examined in detail through Scanning Electron Microscopy (SEM) and Confocal Laser Scanning Microscopy (CLSM) analytical techniques. It was encountered that the differences in the mechanical properties of the pellets produced by each binder system could potentially be explained by the ability of the polymer to interact with bentonite at a macromolecular level.

Oct 30, 2017

By Tingyao Liu, Lihui Han, Qing Liu, Bao Wang, Teng Yang, Yong Sheng

This paper mainly investigates the mass transfer phenomena of rare-earth concentrate from leaching process in Rushton stirred tank reactor with rotate speed of 100-600 rpm. In the research, a certain amount of sphere particles with 50-450 μm in diameter is treated as the mineral particles. Comparison of laboratory experiment data with numerical simulation is performed. The results show that the critical impeller speed for complete dispersion is 300 rpm. And the maximum value of turbulence kinetic energy appeared 15 mm away from paddle, where the mixing time is decreased 55% and 80%, respectively, when mineral particles are injected into stirred tank through one or four filling ports. Moreover, with mixing process going on, the numbers of particles near the paddle region accounts for as much as 58% of the total amount. Meanwhile, following the particle diameter increasing, the particle concentration of the upper part of stirred tank reactor is increased.

Jan 1, 2015

By S B. Fitch, S A. Wilson, A J. R Barr, P R. Searle

Improving the safety culture and performance of any operation is a fundamental goal of every mine operator. Methods of implementing, or changing a culture have developed from the early methods of operant conditioning, for example rewarding crews for achieving nominated safety milestones i.e. 3 months Lost Time Injury (LTI) free through to the current model of engaging a workforce through education and empowerment. As a large scale and mature operation with multiple contractors, Telfer has been exposed to numerous programs throughout its history. This has provided the opportunity to build on and complement these systems by integrating key elements from each. SAFE 360° is a new approach developed to engage the workforce in a holistic approach to encourage positive behaviours across all facets of an individual’s life which results in a focus on situational awareness at all times, rather than being workplace specific. It is based on three key modules: • Emotional Intelligence • Mindfulness • Situational Awareness Each module has a series of modules that help enhance the individual’s sense of self, leading to an ability to self-reflect and self-manage whilst empowering them with the moral courage to challenge their peers to raise standards. Since commencing this SAFE 360° behavioural safety risk management journey in November 2017, we have witnessed a change in the way our workforce engages with each other, their workplace and with management. There has been an increase in hazard perception, identification and ownership of issues, and we have seen a significant decrease in site TRIFR rate from 13.7 to 5.7 (as of April 2019). This paper will provide an overview of the program, how it has been implemented, case studies to demonstrate outcomes and KPIs used to measure effectiveness.

Mar 15, 2021

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987