Search Documents

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By M Chiquito, R Castedo, P Segarra, L M. López, J A. Sanchidrián, J Navarro

The aim of this work is to assess the performance of different constructive solutions against explosions on the strength of masonry walls. The solutions tested, namely an external metal mesh, a glass fibre film on the external face of the wall and a basalt fibre film located on the inner face of the wall, have low to medium cost and are originally designed for other purposes, like seismic protection. Four cubic boxes 3 × 3 × 3 m were built using each of the solutions and typical masonry blocks. In the tests, a spherical plastic explosive initiated in the centre was placed at scaled distance of 2.9 m/kg1/3, so that moderate damage would be caused on the wall. In order to assess the performance of the explosive, pressure gauges were placed at the wall and at different distances from the explosion. Additionally, vibrations were monitored with seismographs in the far field and a high-speed camera was used to estimate the shock wave velocity during the tests. The resulting damage has been evaluated on 13 points of the external wall of each box using a rebound hammer. Damage maps have been drawn for each wall based on these measurements and damage has been assessed inside the box considering the fragments mass launched during the test. The use of external metal mess leads to a decrease of 34 per cent on damage of the external wall and 38 per cent reduction of spalling. The use of a film in the inner wall provides a strong reduction on spalling.CITATION:López, L M, Segarra, P, Castedo, R, Sanchidrián, J A, Navarro, J, Santos, A P and Chiquito, M, 2015. Performance of different constructive solutions against explosions in full-scale masonry walls, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 819–824 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003

By L. Michael Kaas

Any increasing number of restrictions are being placed on mining management's ability to pursue profit. Raw materials pricing, the cost of capital equipment, labor cost, and overhead costs, are becoming more difficult to control. Cost reduction is one of the few remaining areas in which management may still exercise its profit making ability. Equipment maintenance is an area where mine and mill management can readily reduce costs and increase profits. Why is this possible? First, maintenance costs comprise a large portion of total operating cost. Thirty to sixty percent of the operating cost dollar is not unusual. Even a relatively small percentage reduction in this cost represents a very sizeable increase to mining profitability.

Jan 1, 1967

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Mohamed A. Mansour, Ahmed M. Soliman, M. H. El-Naggar

"Grouted helical piles allow significant increase in pile capacity with low additional cost over that of conventional helical piles. They can be particularly advantageous in sites where installation disturbance can reduce or even eliminate the pile shaft resistance. For helical piles with slender shafts, a grout column offers increased buckling resistance under compression loading, and may reduce the potential settlement required to mobilize the bearing component of their plates. This paper investigates the performance of grouted helical piles installed in loose sand. Grouted helical piles were constructed and tested in a controlled laboratory environment. Helical piles with hollow pipe shaft and single helix were grouted during installation. The grout was injected into the soil under high pressure through two nozzles placed above the piles helices. The load test results showed significant improvement in the performance and load carrying capacity of the helical pile due to the formation of a cylindrical grout column along the entire shaft leading to a higher shaft resistance contribution to the total pile capacity. The results suggest that grouted helical piles with slender hollow shaft could be used to support large structural loads. INTRODUCTIONHelical piles are widely used as a deep foundation system for different engineering applications. They represent an attractive foundation option because of their cost effectiveness, ease of installation even in limited access areas, low levels of noise and vibrations, and their ability to be installed through ground water without casing. In addition, they allow immediate loading upon installation. Helical piles are installed into the ground by applying a mechanical torque to the pile head. The installation torque monitoring provides a kind of quality control during the construction of helical piles. It could be used in predicting the ultimate pile capacity using several capacity-torque correlations (Livneh and Elnaggar 2008; and Hoyt and Clemence 1989).However, helical piles installation can cause soil disturbance within the annular zone affected by the pile helices. This disturbance can introduce fissures within the pile cylindrical failure surface (Vesic 1971; Mooney el al. 1985; and Zhang 1999). Thus, the shear strength of the soil decreases along the affected zone. Bagheri and El Naggar (2013) evaluated the installation effects of helical piles in sand. They reported that as the helical blade proceeds into the ground, sand within the cylindrical path circumscribed by the helices experiences torsional and vertical shearing accompanied by sand displacement and stress changes. This process is more pronounced in the case of multi-helices and large diameter anchors. Bagheri and El Naggar (2016) evaluated the installation effects of helical piles in structured clay. They indicated that the behavior of the helical pile and its capacity are significantly affected by the degree of soil de-structuring induced by the penetration of the pile shaft and helices. In addition to the installation disturbance, helical piles have other drawbacks including; high potential settlement required to fully mobilize the bearing component of their plates, low buckling resistance of their slender shafts, and the incomplete rigidity of the coupling joints along the pile shaft that allow some lateral movement under compression loading (Vickars and Clemence 2000)."

Jan 1, 2016

By LefTvre Y

In May 1991, AZSA commissioned a new conventional Cell House. This paper focuses on the major improvements introduced in the design and the construction of the equipment, machinery and control. An effective control system together with good reporting and routine operation has resulted in quality control of the Cell House at the highest possible level. Consequently the monthly current efficiency consistently averages above 93 per cent with a total energy usage of 3000 AC kWh/t of cathode zinc. The new concept for the year 2000 and beyond is introduced.

Jan 1, 1993

By Luiza Esteves

Corrosion testing was performed in white liquor from a Brazilian Kraft mill. Specimens of duplex stainless steel (DSS) and lean duplex (LDSS) were exposed at 170 °C for 30 days to simulate conditions of the digester. Corrosion rates were determined from weight loss measurements. After this exposure, the corrosion products formed on the steel surface was characterized by using scanning electron microscope (SEM) equipped with EDS, X-Ray Diffraction (XRD), and X-ray photoelectron spectrometer (XPS). EBSD can be used to quantify of basis balance phases in DSS and LDSS. General corrosion rates for UNS S32304 LDSS were higher than the UNS 31803 DSS in industrial white liquor at 170 °C for 30 days. XPS and XRD analyses indicated that the film formed after the immersion test may be consisted by Fe and Cr oxides and sulphides.

Oct 30, 2017

By McQuade C. V

Mining is an activity which has, in the past, been regarded as often leaving land in a condition unfit for further use. As the need for development that is both economic and ecologically sustainable has grown, so the issue of re-use of land after mining has become significant. During operation it is usual that mine environmental conditions which minimise unnecessary or avoidable environmental impact are agreed with the regulatory authorities . These conditions are usually set down in such a way that they can be interpreted reasonably well by both miners and regulators. However, the conditions to be met by a mining company before it can be absolved of responsibility of a site are often less clear. The close-out criteria by which the success of rehabilitation programs will be judged have received little attention in the past. These conditions are now growing in importance as the costs of rehabilitation of a mine site to an agreed post-mining land use assume greater significance in the economics of mining. This paper briefly describes the status of close-out criteria presently being applied across Australia. A comparison is made with similar guidelines from other countries.

Jan 1, 1994

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By Xiaoguang Zhao

The coal mining area in Northern Shaanxi, China, has been taken as the study area, and the damage mechanism of the ecological environment is discussed on the basis of analyzing the characteristics of natural eco-environment and resource development in this area. Mining subsidence is taken as an example, and by using the Gray Correlation Analysis method, the key impact factors have been selected. An assessment model with fuzzy comprehensive evaluation has been constructed, and 12 coal mines have been quantitatively assessed. This paper also constructs an ecosystem health assessment method and index system in the coal mine area on the basis of ecosystem health theory, and assesses the ecosystem health status in the Shenfu coal mining area from 2000?2006. The research results are expected to help the eco-environment protection process in the designated coal mining area.

Aug 1, 2013

By Irving Hartmann

The fire end explosion hazard of excessive coal-dust deposits in mines has been recognized for many years, and important measures have been developed for reducing dust formation and to alley loose dust near its source. Nevertheless, in the course of normal mining it has been estimated that 1 to 3 percent (in some thin, friable seams up to 10 percent) of the total coal mined is reduced to dust of through-20-mesh fineness. In highly mechanized, continuous mining operations the production of fines is even greater. Most dust is trapped near its point of origin and removed from the mine, but large quantities are transported by the air current and by haulage into entries, where the greatest proportion settles on the floor and the balance on the rib and roof surfaces. The latter is generally finer in particle size than the floor dust; this, coupled with its more advantageous position for dispersion, makes the rib-roof dust (also to be referred to as overhead dust) a greater potential explosion hazard.

Jan 1, 1954

It is very rare in the underground hard rock environment to find a deposit that is ideally suited to a specific mining method. Usually the irregular shape of the orebody will allow the deposit to be extracted by more than one mining method. During the prefeasibility stage, a number of conceptual mine designs are generally evaluated to see which offers the best method of extraction for the deposit. The selected method is usually based on key decision criteria such as the overall extraction of the orebody, the amount of metal produced annually and the unit cost of production. Often the prefeasibility study document will state that the project has an NPV of æxÆ million dollars. This statement can be made without any quantitative consideration of the likely risks of the mining methods reviewed or the level of confidence in the estimation of the NPV. By assigning a probability of failure to each component of the mining cycle a measure of the risk for each method can be determined. One mining method may provide the highest NPV when it is performing well, however, there may be a higher risk of a major failure impacting on the performance of that method, eg the failure of a mass blast of a crown or rib pillar. This paper will present a flowsheet approach to the use of risk analysis for determining the likely production rates of different mining methods. This framework allows the annual metal output to be estimated and from this the NPV for each method. A level of confidence can be applied to the estimated NPV for each option. An example will be presented on how this technique has been used within the Normandy Group.

Jan 1, 1998

By D. Arku

The increased use of sensors to facilitate automation has led to an explosion of data. As data sets grow in size, their use becomes more complex. Therefore, there is an incentive for reducing the size of the datasets, as long as this does not compromise information gleaning. With this in mind, this project explored basic aggregation as a viable alternative to amassing large amounts of data. The goal of the project was to determine if one would arrive at different conclusions had they analyzed aggregated data instead of raw data. In a mine, operational data is typically used for tracking process statistics, correlation between factors, autocorrelation and multivariate models (for a factor of choice). Therefore, this project compared results from such analyses when it was conducted with aggregated data (AD) with the results of analyses conducted with raw data (RD). The data consisted of one-minute-apart readings from a semiautogenous grinding (SAG) mill on the horsepower, feed rate (tons per hour), rotations per minute (rpm), noise, recycle (tons per hour), density (% solids) and bearing pressure (psig). This data was aggregated by averaging five and 10 continuous (one-minute) observations. Changes in statistical measures between the two approaches were typically within 5% of each other. Differences in correlation coefficients between RD and AD(s) were also within this range. Autocorrelations present within RD were preserved in AD, as long as the time lags were scaled for the amount of aggregation. Regression and neural network models were also developed for power consumption. The prediction performance of developed models was similar whether one used raw data or aggregated data. Overall, it appeared that aggregating the data based on 5- or 10-minute time spans would not have resulted in conclusions (from simple or complex analyses) being different from using raw data. In other words, whether one had used raw data or aggregated data, the conclusions would have been the same, suggesting that time domain aggregation, a common industry practice, is a good alternative to storing high-density data in this case.

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By L. A. Cornish, J. W. van der Merwe

"The hydrofluoric acid (HF) industry in South Africa uses normalized mild steel (SA 516 Gr 70) for the storage and distribution of its technical-grade product (70% HF). The technical-grade acid is split from the anhydrous hydrogen fluoride (AHF) product during distillation just after HF is produced, in a stainless-steel-lined kiln, from the reaction of calcium fluoride (CaF2) with sulphuric acid (H2SO4). Uniform corrosion of the storage tanks is mitigated during commissioning by contacting the steel with 70% HF. A corrosive reaction takes place (2H+ + 2F- + Fe - H2 + FeF2) to form scale inside the tank which diminishes the attack of the steel by fresh HF, thus prolonging the service life expectancy of the vessels. This iron fluoride scale in the vessel grows continually, resulting in corrosion of the vessels continuing at a predictable rate (approx.0.5 mm/a) since the first commissioning of the tanks at Necsa in 1993. In early 2012, an increase in the average corrosion rate of the tanks to 3 mm/a measured at and below the liquid band in the storage vessels was noted. Three months later the corrosion rate had increased to 30 mm/a, just before the first leak from the tank was detected. The tanks were decommissioned shortly afterwards and an investigation revealed that the rapid corrosion was due to the presence of increased levels (>50 ppm) of nitric acid (HNO3) in the tanks, which attacked the fluoride layer protecting the steel.The oxidation characteristics of high concentrations of HNO3 with low concentrations of HF on stainless steel surface treatment are well documented. The effects of low levels of nitric acid on the corrosion of steels in sulphuric acid are also known, but no suitable published data currently exists on corrosion by high HF concentrations with low HNO3 concentrations. Establishing the rate and mechanism of corrosion by HNO3 (0.1 to 1%) in 70% HF is currently a high priority for the HF industry in South Africa and will become increasingly important in the near future due to depleting fluorite reserves and cheaper, but less efficient, processes producing H2SO4 with higher impurity levels, which were not anticipated in the original plant design. The aim of this study is to simulate the corrosion conditions in the plant on a laboratory scale in order to establish the corrosion characteristics of the steels used in the HF plant, which are increasingly exposed to the HNO3 impurities that tend to concentrate in the final technical-grade HF acid product."

Jan 1, 2016

By Jurij Karlovšek, Wolfgang Angerer, Vojtech Ernst Gall, Jacob Grasmick

The International Tunneling Association (ITA) Working Group (WG) 22 “Information Modelling in Tunneling” has developed a guideline for the implementation of Building Information Modeling (BIM) concepts for Bored Tunneling Projects. The guideline primarily covers the use of BIM during the conceptual and delivery phases of a project. It provides Owners with an introduction to BIM, an overview of the current capabilities of BIM, and a guide for implementation for a Bored Tunnel. The document will be officially published at the World Tunnel Congress (WTC) in Copenhagen in 2022. This paper describes the need for the guideline and provides a preview of its contents.

Dec 1, 2022

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsolidated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries.

Jan 1, 1949