Search Documents

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By R. von Gal

Hazelett Strip-Casting Corporation has been producing the Hazelett® twin-belt casting machines for copper casting since the mid-1960s. The first commercial casters were developed for copper alloy strip and anode plate. In 1968, development work was started to adapt the twin-belt caster for copper bar casting to be rolled in-line into wire rod. Since then, 36 casters have been sold as part of the CONTIROD® system for the production of a substantial portion of the world's copper rod supply. A unique feature of the twin-belt caster is the mold's ability to comply with the size and shape of the cast bar as it shrinks during solidification. Maintaining contact between the mold and the bar provides a high rate of heat transfer as well as other benefits, including the prevention of surface imperfections caused by remelting in the mold. This paper will give an overview of the continuous evolution of the twin-belt caster technology with an emphasis on recent developments in compliant mold technology for copper casting.

Jan 1, 2007

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The performance of the improved microclimate suit by N. B. STRYDOM M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, B.Sc. (Potch.) (Visitor), and W. H. VAN DERWALT, M.Sc. (Potch.) (Visitor) An assessment has been made of a new improved microclimate jacket when worn by men working for four hours in a hot environment (wet-bulb temperature of 33,9°C and an air speed of 0,4 m/s) and at work rates of 35 Wand 70W. At the lower rate of work in heat, the use of microclimate suits maintained the rectal temperatures of the men at almost the same level as when they worked without that protection at normal room temperature (20°C). At the greater rate of work without protection, the men's rectal temperatures rose to 40°C within two to three hours, so that they could not complete four hours of work. When they wore microclimate suits, they easily completed four hours of work, and their rectal temperatures were lower than when they worked at the lower rate without protection.

Jan 8, 1975

To improve operational effectiveness of enclosed cab filtration systems. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. Most cab designs achieve heating and air conditioning effectiveness by recirculating most of the interior cabin airflow, with a smaller portion of the outside air added to the cab as makeup air. Both the recirculated cab airflow and exterior makeup air added to the cabin should be efficiently filtered, with the makeup air positively pressurizing the cab interior. Ideally, operator cab air filters should provide at least 99% capture efficiency for dust particles as small as 0.3-pm aerodynamic diameters. These higher efficiency air filters provide good dust control for the equipment operator, but tend to accumulate dust more quickly than lower efficiency air filters.

Jan 1, 2001

By E. P. Gush

Diamonds, an enigma in a mineral resource sense. Chemically, diamonds are no more than carbon crystals in a cubic system-formed one might add under conditions of great pressure and temperature. They have certain physical properties which are fairly unique. They are very hard, they have a high refractive index, they luminesce, some of them fluoresce, they have a high specific gravity, they don't wet and they are a good conductor of heat. In a way, a rather clinical set of qualities. Of course, these qualities are what give diamonds their use and their beauty. It is on the emotional side that they get complex and stir memories of legends, of beauty, of wealth and romance, of war, happiness, bad luck and curses. It is on the emotional side that the value of a diamond is established, if such a thing is possible. Diamonds are extremely varied, there are more than 5000 categories into which they are sorted, so there is room at each point across the spectrum for their individualities to emerge, and accordingly their attractiveness to each buyer is unique.

Jan 1, 1994

Dynamic hydrothermal modeling is a tool that can aid in studying problems associated with hydrothermal ore deposits and can help increase our understanding of the spatial distribution of ore within hydrothermal systems. Models are constructed by a sequence of steps involving development of a conceptual model, followed by its mathematical description in terms of governing equation with accompanying initial and boundary conditions. This equation is then solved either analytically or numerically. The four model types ò that fully describe a hydrothermal 'system are those for fluid flow, heat and ore solute transport, and deformation. At Renison, models have been used to help understand two major exploration problems. These are the controls on ore localisation in dolomite horizons and feeder faults respectively. The types of models used ò have simulated the distribution of all mineral zones, pyrrhotite, and temperature in the dolomites. This has allowed evaluation of the effects on ore localisation by physical and chemical heterogeneities within the dolomite host rocks, and allowed estimation of potential controls in different physical and chemical environments.

Jan 1, 1987

By M. Boussuge

Ceramics and refractories have many common constituents and consecutively exhibit several analogous properties. For example, concerning the thermomechanical properties this paper will focus on, the type of creep that can be observed in both materials is often the same (kinematic hardening). Changes in microstructure (phase transformation, dehydration, sintering, crystallisation,...), induced by heating and/or cooling, can also drastically modify the mechanical behaviour of ceramics and refractories. But the coarse granulates, the porosity and the impurities contained in industrial refractories may lead to specific responses of this material to thermal and/or mechanical loadings. In particular, some differences can be observed with technical ceramics in the main type of damage observed in service : diffuse damage in refractories (microcracking) and localised damage in ceramics (macrocracking). In this paper, the possibilities of transferring a part of knowledge from ceramics to refractories will be discussed, in the field of thermomechanical properties : experimental characterization techniques, mechanical behaviour models. Finally, some problems caused by scale effects and by the integration of thermomechanical properties of refractories in the numerical simulation of industrial structures will be evoked.

Jan 1, 2004

By Ali Akbar Mottahedi

It is known for a long time that the reaction of oxygen with carbon, silicon, iron and many other elements is exothermic. The heat of released from these kind of reactions can decrease the time of fusion of iron and steel for metallurgical purposes in the electrical arc furnaces. By decreasing the time of fusion, we increase the rate of process and the amount of production. So, by blowing oxygen in to the furnace, we can reduce the consumption of electricity and save cost. There are many problems in the procedure of the oxygen blowing. In this project, the theoretical aspect of the oxygen blowing and its side effects into the arc electric furnaces are investigated. An oxygen blowing system into the arc electrical furnace of metallurgy department of Machine Sazi factory was also set up. This process reduced the consumption of electricity up to 22% and increases the rate of production, by reducing tap ? to ? tap time up to 15%. In this project; all oxygen blowing systems and its control were set up.

Jan 1, 2006

By R. Markovic

The objective of this research study was the investigation of heavy metal removal from wastewaters of the "SARAKA" stream by using low-cost materials. These wastewaters flow into Krivelj River and through the network of existing rivers into regional water reservoirs. Sawdust, cardboard and fly ash were used as reactive materials in laboratory studies. Sawdust was obtained from oak and fir-wood while fly ash from heating station Bor, bitter-oak and oak. Experiments were carried out using real Saraka stream wastewaters and the degree of removal for iron, copper, manganese and zinc was investigated. The content of these heavy metals in Saraka stream wastewaters was under the limit of III and IV class of water (Law on Water - Official Register of the Republic of Serbia). Parameters such as flow rate of water, pH and effluent volume, contact time between water and reactive material, etc, were monitored during the experiments. All used materials give satisfactory results for iron and other heavy metals removal; the highest degree of removal was obtained by using fly ash.

Jan 1, 2006

Benjamin B. Thayer was elected as representative of the Institute on the John Fritz Medal Board of Award vice Albert Sauveur, whose term expires. Robert M. Raymond was confirmed as member of the, Engineering Foundation Board for two years in accordance with the By-Laws of the United Engineering Society. The following preambles and resolutions were passed: WHEREAS, the Chamber of Commerce of the United States is taking a vote, through the Chambers of Commerce, Boards of Trade and other constituent members of the National Chamber situated throughout the country, on the question whether or not the primary natural resources, comprising timber, the ores and deposits of useful metals, and' the deposits of minerals, which are a source of heat, light and power, should he exempt through remedial Congressional legislation from the restrictive limitations of the Anti-Trust Acts, and WHEREAS, a Committee of the National Chamber, the Chairman of which is a Past President of the American Institute of - Mining Engineers, has recommended favorable action upon this question, and

Jan 2, 1917

By Oliveira JF

Thiourea is an alternative reagent for cyanide in gold leaching. The recovery of gold from acidic thiourea solutions by adsorption on activated carbon is based on methods similar to those applied for the extracting of gold from cyanide solutions, but the mechanism involved in the process is not completely understood. In the present work, studies were carried out to evaluate the adsorption of gold onto activated carbon. Experimental data showed good agreement with both the Freundlich and Langmuir isotherms. The adsorption of gold from acidic thiourea solutions proved to be an endothermic process, while the adsorption from cyanide is known to be exothermic. The isosteric heat of adsorption of -11.3 kcal/mol in the early stages of the adsorption is an indication of a process involving chemisorption. The effect of temperature was studied between 15¦C and 55¦C. An activation energy of 3.5 kcal/mol was determined by the Arrhenius plot, which indicates that the controlling step in the kinetics of adsorption is the diffusion onto the porous structure of the activated carbon.

Jan 1, 1993

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (S) of the liquid-to-solid transfer at each temperature has been derived S - ZLXL(XL - P) + Zsxs(P - XS) ZL(xL - P) + Zs(P - XS) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, XL and xs are the composi-tions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under considera-tion. The S equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known.

Jan 1, 1940

By Robert H. Richards

In the latter part of December a batch of amalgam was retorted and the tin in the retort uncovered while at a low red heat, and allowed to cool slowly to a temperature more suitable for ladling into moulds. It was then ladled and made what appeared to be nice, white, malleable block tin. On February 15th our attention is called to the fact that the tin is brittle, and on examination we find that the molecular condition of the pigs has changed to the extent of one-half its material. The change shows itself by an enlargement appearing on the surface something like crystallization, and comes in spots. The condition of the metal in these spots is very peculiar. It has changed from a malleable metal to a brittle one, with a structure somewhat resembling stibnite, and a color very considerably darker gray than tin. The analyses of the two parts of this tin pig showed the following results: Mercury. Tin. Specific Gravity. Crystalline part,.....2.62 97.24 6.175 Malleable part,.....2.38 97.50 7.387

Jan 1, 1883

By T. Cutard, E. Yeugo Fogaing, C. Gault, H. Marzagui, N. Prompt, M. Huger, C. Deteuf

This paper deals with studies made in the field of the French research network PROMETHEREF. Several refractory castables are considered in this program. In the present paper, one of these materials is considered, it is a low cement castable based on andalusite aggregates. A particular attention is paid to microstructural changes during the first heating and on their effects on the high temperature mechanical behavior. Microstructural evolutions have been characterized by the way of dilatometry, scanning electron microcopy and X-ray diffraction. In-situ observations by environmental scanning electron microscopy gave complementary results on these high temperature microstructural changes. They deal with microcrack formation, phase changes, crystallization, liquid phase formation and sintering. By propagation of ultrasonic waves, high temperature continuous measurements of the Young's modulus have been made. Results confirm the existence of microstructural changes and allow to quantify the Young's modulus variations all along specific thermal cycles. High temperature four point bending tests and room temperature tensile tests were made in the same temperature range. Behavior evolutions could be found and interpreted with the help of previously mentioned results.

Jan 1, 2004

Equilibrium in Lead Smelting. By S FREDERICK RAVITZ AND KENNETH E FISHER (Tech Pub 681, also Trans , vol 121 2300 words) Four liquids are ordinarily produced in lead smelting, namely, bullion, speiss, matte and slag To determine whether these exist together in equilibrium, the distribution of gold and silver among them was measured To crucibles containing similar mixtures of all four products, varying amounts of silver were added, and the crucibles were heated together under the same conditions for 3 hr, during which the charges melted and separated into four layers After cooling, these layers were assayed for silver, and the distribution coefficients, 1 e , the ratios of the concentration of silver in any particular layer to that in the bullion, were calculated In each experiment, each distribution coefficient was found to be constant, regardless of the amount of silver used Similar results were obtained using gold instead of silver The constancy of the distribution coefficients indicates that the bullion, speiss, matte, and slag exist together in equilibrium

Jan 1, 1937

Canadian owned Lake are carriers will be used again this year in an attempt to make up the deficit caused by the two months steel-strike. Buffalo mills need between 5 million and 6 million tons of ore before the Lakes navigation season ends. Mutual Security Program aid will help reactivate Austria's largest iron ore mine. The Erzberg development is one of the moat important in Europe. MSA announced approval of $500,000 in supplemental financing of equipment. Following the war, the Russians stripped the Erzberg and Radmar deposits of equipment. The he Carborundum Corp. is going to build a $2.44 million plant at Akron, NO.. TOP near Niagara Falls for production of rare metals used by the Atomic Energy Commission. A subsidiary, the Carborundum Metals Co., Inc.,, will produce zirconium, hafnium sponge metals. The pyrochlore rich Sukulu Hills in Eastern Uganda will be mined under a pool arrangement including Tinto Mines, Monsanto Chemicals and Frobisher Mines. The combine will be known as the Uganda Development Corp., Pyrochlore is used in the manufacture of heat-resisting. alloys for Jet engines.

Jan 1, 1952

By Cyril Stanley Smith

BETA brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, but at low temperatures [ ] an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 490°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An [ ] excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shockley.1 All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching. With most ordered alloys, cold-working induces disorder and

Jan 1, 1942