Search Documents

By F. N. Siddiquie, Mohd Shaif, Rajiullah Khan, Juned Alam

Manganese ore bodies of Banswara Mn belt were classified into stratiform and stratabound types, based on their mode of occurrence, distribution, and their chemical characters. These ore bodies generally composed of braunite, pyrolusite, cryptomelane/ psilomelane, wad, etc. The stratiform-type Mn ore bodies are conformable with the associated host rocks (Mn phyllite, etc.) and occurred in the form of layers, bands, etc., which are variable in their shape and size. These ore bodies are also strongly folded with the enclosing host rocks. The others, which are stratabound-type Mn ore bodies, also showed an intimate association with the associated host rocks. These types of ore bodies occurred in thin layers, pockets, lenses, stringers, etc. The classified ore bodies are confined with Kalinjara formation of Aravalli Supergroup of Paleoproterozoic age. The ore bodies are structurally controlled and well associated with phyllite, schist, limestone, quartzite, etc. The stratiform-type ore bodies constitute a marginal to low Mn grade and are also characterized by lower Mn content (26.19–39.24%) along with the Mn/Fe ratio of 7.16–12.23, while the stratabound-type Mn ore bodies are rich in Mn (35.92–49.64%) along with the higher Mn/Fe ratio of 14.15–23.97. However, the poor Mn grade along with high siliceous impurities of Banswara Mn deposits is subjected to them for intermittent mining activities in the past and, consequently, did not attract the scientific and industrial community for the evaluation of these resources. Therefore, the authors attempted this study in a scientific and systematic manner (mode of occurrence/distribution and possible methods for evaluation/exploration) to evaluate the potential of existed and newer Mn deposit resources in the Banswara Mn belt. The whole findings would be very much helpful for exploration/ mining geologist along with other concerned, to completely evaluate these Mn deposits in the future.

Aug 16, 2021

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By H. D. Hoskold

I. Instrument-Parts and Implements. Cross-hairs ; Stadia-measurement; Fineness of Graduation ; Cylindrical Gradu ation ; Nonius; Vernier ; One Vernier or two ; Leveling-Screws ; Troughton & Simms' Shifting Tripod-Head ; Hoskold's Shifting Tripod-Head; Hoskold's Extensible Tripod ; Electric Lamp ; Plumb-lines; Chain. II. Instruments. Compass (Mine-compaes of 1518, Compass of 1541, and Agricolals of 1556, Voig tel's Setz-compass, Circumferentor, Stanley's Hedley Dial, Compass on Tele scope, Hanging Compass, Lack of Precision) ; Plane-table; Octant and Quadrant; Theodolite and Transit (Evolution of the Theodolite, Scott's Tachymeter, Hoskold's Engineer's Theodolite, Angleometer, Precision of Mine-Theodolites). I. Instrument-Parts and Implements. Cross-Hairs.—Mr. Scott‡ says Lean's dial " might also have been provided with a diaphragm and cross-hairs; for Huygene discovered that any object placed in the common focus of the two lenses of a Kepler telescope (1611)- appeared as distinct and well defined as any distant body. Following this established theory, in 1669 Jean Picard, Marquis Malvasia and others crossed silken fibers in the mutual focus of their astronomical instruments." If by this Mr. Scott means that Huygens and Picard first devised and applied cross-hairs to the focus of the telescope, the writer cannot agree with him. Huygens did not describe " his telescope without tubes until 1684, in his Astroscopia Compendiaria."§ Moreover, it is recorded that the English astronomer, Gascoigne,?

Jan 1, 1902

By J M. Nel

Richards Bay Minerals (RBM) has recently undertaken an exercise to improve orebody basal definition. Older mineralisation bases (pre-2005) were highly erratic using old protocol reverse circulation (RC) (also known as Air Core) drilling and interpretation. The erratic nature of this estimation tool, resulted in impractical modelling towards the end of mineralisation (EOM), difficult mine design and unrealistic reconciliation. New protocol drilling, which includes high definition SONIC drilling data, has provided more data to be available for more accurate interpretation. Recent advances in drilling methodology has allowed for better penetration depths for SONIC drilling, which was previously restricted to approximately 80 m (pre-2005). This improved data set allows more emphasis on geological interpretation with factors such as lithology, slime content, and mineral species distribution. These factors when in unique combination enable more accurate and realistic EOM data points. These points are modelled into surfaces using conditional simulation techniques and result in a vastly smoother surface and consequently, a more representative resource.

Oct 5, 2011

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M. H. MacLeod

"IntroductionTHE ORE PASS raise system at the H.B. mine as contracted by the Patrick Harrison Company consisted of two raises 6 ft. by 10 ft. in section •at 60 degrees to the horizontal. No. 88-88 raise, the longer of the two, was a straight raise 690 feet long, with access only from the bottom. In addition, this raise had two branch knuckle-backs only one of which was driven by. the Patrick Harrison Company. The other, known as 88-89 raise, was 540 feet long with knuckle-backs at 280 feet and 410 feet. Its access, also, was from the bottom (see Figure 1)."

Jan 1, 1954

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement.This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects.The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied (1). The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2017

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

By M. Savich

A graphical method has been developed for the evaluation of the U.S. Occupational Safety and Health Act Noise Exposure Index and the Equivalent Continuous Sound Level. The method makes use of a noise survey form and a mechanical integrator with two sliders, and is less tedious and susceptible to error than alternative methods. The graphical method is adaptable to various codes for noise exposure and may be used with any instrument that measures noise level. One example of its application to a practical situation in a Canadian mine is given to demonstrate the procedure .

Jan 1, 1978

By J Paradis, K Dudgeon, M Topping

At Newmont’s Jundee Operation, exploration and resource geologists collaborated to produce an open pit resource model. Using a variety of modelling and estimation techniques but no new data, an uneconomic underground target was converted into a potentially economic open pit evaluation. During an industry downturn, it is more important than ever to efficiently share expertise, ideas and resources to problem solve and produce meaningful project outcomes. The two departments brought together different methods and ideas, and the process showed that certain methods worked better than others in different situations, thus the appropriate method was applied to each part of the evaluation. The results were used to create new procedures and improved lithology modelling and resource model estimations. Adaptability of the geology departments and collaboration such as this are key to ongoing improvements and future mine life at Jundee.CITATION:Dudgeon, K, Paradis, J and Topping, M, 2014. Cook open pit model – the hurdles: how we leapt, lunged, stumbled and overcame them, in Proceedings Ninth International Mining Geology Conference 2014 , pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001