Search Documents

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

Most mineral products exported from Australia to Japan, with the notable exception of coal, are purchased with weight and quality determined on discharge. Sampling of imported minerals for purpose of payment is done at facilities owned and operated by the purchaser. The selling shipper is represented at the weighing, sampling and testing by an independent inspection group who supervises the whole procedure. Sampling and testing are done within the provisions of the contract between the two parties, and normally in accordance with the relevant Japanese Industrial Standards (JIS). These JIS specify such things as the number and mass of increments to be taken; the practice of taking these increments; the method of determination of moisture, size distribution and quality. The JIS concerned with sampling however, are meant to be basic guides rather than rigid rules. Hence sampling and testing practice varies from plant to plant. In general Japanese sampling facilities and methods are elaborate and efficient. Opportunity is given for the discussion of varying technical viewpoints between consumer and shipper. However the resolution of differences and the implementation of changes normally takes a long time. Such discussions seem best reduced by prior contract agreement on reasonable specifications and detailed testing methods. The independent inspectors

Jan 1, 1976

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations addressing hoist safety, automatic hoisting, and shaft obstruction. The regulations are quite similar among provinces, with only slight differences. Risk-mitigation strategies used in other industries are discussed, including their applicability to mine hoists. The specific case of software safety is introduced through examples. The mitigation of software failure is based on the use of the software lifecycle as recommended by the International Electrotechnical Commission (IEC) 61508 standard. Finally, ways to improve hoist safety are proposed.RÉSUMÉ Le présent article compare entre elles les diverses réglementations provinciales canadiennes concernant la sécurité des machines d'extraction, le levage automatisé et les obstructions dans les puits. Les réglementations sont assez semblables entre les provinces, mais elles comportent de légères différences. Les stratégies d’atténuation des risques utilisées dans d’autres industries sont abordées, incluant la possibilité de les appliquer aux treuils de mines. Le cas spécifique de sûreté des logiciels est abordé par des exemples. L’atténuation de la défaillance des logiciels est basée sur l’utilisation du cycle de vie du logiciel, comme cela est recommandé par la norme 61508 de la Commission électrotechnique internationale (CEI). Des moyens d’améliorer la sécurité des treuils sont également proposés."

Jan 1, 2016

By O. C. Wheeler

During 1938, Colombia witnessed greater activity in oil prospecting and development than in any previous year in its history; more wells were drilled, more potential production established, more geological and geophysical work was accomplished, and more leases and concessions were acquired. Many companies, including the Texas, Socony Vacuum, Richmond (subsidiary of the Standard Oil of California), the Shell, and Tropical, contributed to this activity. Probably the most noteworthy development was in connection with the Barco Concession, which forms part of the Maracaibo Basin in eastern Colombia, adjacent to the Venezuelan frontier. There a great deal of preparatory work was accomplished in addition to camp and other construction, 20 producing wells were drilled and work was begun on the construction of a 12-in. pipe line to transport the oil to the port of Covenas, a distance of 260 miles. It is reported {hat 58,000 bbl. daily initial production was established during the year and is awaiting an outlet through this pipe line. Leasing and exploratory operations in Colombia continued active throughout the year; applications were made for concessions covering more than 1,100,000 acres of national lands and, in addition, leases were taken up on large areas of privately owned lands. Under Colombian law

Jan 1, 1939

By Pier Luigi Iovino

As Technical Director of the Naples, Italy based Fondedile, a geotechnical construction firm specializing in static restoration of structures, Fernando Lizzi, Ing., devoted over 30 years to the pursuit and advancement of static restoration and subsoil strengthening. Seismic events, construction of new structures on polluted and/or unstable soils in urban areas, and a need to carefully preserve and restore delicate, war-damaged historical structures, manifested the need for underpinning projects. Traditional construction methods and approaches, such as underpinning with additional foundation masonry, were not suitable and would have further jeopardized the stability of the structures. The introduction of the palo radice (root pile) revolutionized the field of underpinning. At the time of the first application of micropiles, the industry standard was driven piles. The drilled micropile was conceived and first implemented in the early 1950s, as an innovative means to underpin sensitive, historic structures and structures in urban areas. Specifically, the new construction technique was conceived as a less expensive alternative, designed to accept structural loads, be installed in limited access areas, in varied working and sub-surface conditions, which did not involve changing soil characteristics, and had minimal disturbance to the structure being underpinned, or to adjacent structures.

Jan 1, 2003

By John Goheen

CONSIDERABLE work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods ¼ in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constructed to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses 2200-2250° F. (1205-1234° C.) Yellow brasses 2250-2400° F. (1234-1318° C.) Bronzes 2300-2550° F. (1260-1400° C.)

Jan 11, 1921

By R. J. Sawyer

*An earlier version of this paper was presented at the IMM meeting, "Use of Cultivated Carbon in Extraction of Gold and Other Metals," held in London in January, 1983, and was subsequently published in Trans. IMM (Sect. C: Mineral Process. Extr. Metall.) in December, 1983. Reprinted with permission of The Institution of Mining and Metallurgy, London. INTRODUCTION This paper describes the development of the processing route for the Alligator Ridge Mine which commenced operation in 1980. It also reviews the modifications which have been made to improve operating efficiency during the three years that the mine has been in production. Alligator Ridge is located 70 miles Northwest of Ely, Nevada. The mine is a joint venture between Amselco and Nerco with Amselco acting as operator. The deposit consists of micron sized disseminated gold imbedded in siltstone. Although definitive conclusions have yet to be drawn as to the age and origin of the deposit, it is probable that it is young by geological standards, perhaps only 5 million years old. It is likely that the gold was brought to the surface by hot springs. As the superheated solutions rose through the porous siltstone, they redeposited minerals in the rock, forming the present ore bodies.

Jan 1, 1984

By Haydn H. Murray

The three major catalyst markets that utilize industrial minerals as raw materials are petroleum refining, chemical processing, and emission control. Because of economic, competitive, and regulatory pressures, catalyst producers are pushed to develop products with improved performance to meet changing environmental standards. Also, refiners are demanding new families of cracking catalysts that will crack residual fuels. In 1987, worldwide cracking catalyst sales amounted to $457 million (Occelli, 1988a). Recently enacted federal and state laws to improve air quality have prompted strong growth for environmental catalysts, which in 1989 accounted for more than a third of the $1.9 billion catalyst market in the United States (Farrauto, Heck, and Speronello, 1992). A catalyst is a material that promotes or enhances a chemical reaction but does not itself enter into the reaction. One of the more important mineral groups used as catalysts is clays. The first recorded use of clay as a catalyst was its use in the dehydration of alcohol (Bondt et al., 1797). Clay minerals that are used as catalysts are kaolinite, halloysite, smectite, palygorskite, and sepiolite. Minerals used as catalysts, catalyst supports, or as a raw material to make zeolites are kaolinite, halloysite, sodium montmorillonite, calcium montmorillonite, hectorite, palygorskite, sepiolite, talc, calcined kaolinite, gibbsite, chlorite, and titanium dioxide.

Jan 1, 1994

By E. J. Meets, C. F. Meyer

Bord and pillar mining at shallow depth (400 m approx. maximum) is widely used in South African coal mines. One of the problems encountered in extracting coal in this manner is the ventilation of advancing bord and pillar headings. The traditional ventilation methods of force, exhaust and overlap (force/exhaust) are reasonably effective but tend to be both cost and labour intensive. Ducting often restricts the available free area of roadways thus impeding the transport of coal and other materials inbye the coal production section. Due to the above facts, ductless fans are currently being used to minimize the amount of ducting required in advancing sections. Two different types of fans are used, namely, vortex fans and the so-called `jet' fans. Vortex fans were developed from the fan blade design used for vertical take-off aircraft. The fans have the capability of delivering air over distances of about 30 m in the underground situation without any ducting attached to it. Jet fans are standard axial flow fans fitted with outlet reduction pieces which increase the velocity pressure at the discharge to such an extent that the air delivery distance is improved to almost match that of vortex fans. The paper describes some applications of both these fan types in advancing bord and pillar sections.

Jan 1, 1993

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

Development of the Greenvale orebody, containing 40,000,000 tonnes of nickel ore, began in 1971 and production commenced in 1974. Annual capacity is 2,800,000 wet tonnes. The variations in ore grade and physical characteristics which occur throughout the ore- body had a major influence on the selection of mining methods, grade control procedures, and equipment. After removal of overburden by scrapers, ore is excavated by draglines sidecasting into windrows. Feed to the crushing plant is .reclaimed by front end loaders into rear dump trucks according to a grade selection pro- gramme. After crushing, ore is stockpiled into blended units of ore of required quality. Ore is stacked and reclaimed for train loading using techniques designed to give maximum mixing of ore characteristics through Bach unit. These procedures are repeated on discharge at the plant site at Yabulu. The railway, constructed by Queensland Nickel Pty. Ltd. to Q.G.R. standard, and operated by the Q.G.R., is 216 km long and includes eight major bridges and three tunnels. Two trains per day, one of four locomotives and 92 waggons, and one of three locomotives and 69 waggons, haul crushed ore to Yabulu. Train loading is semi-automatic. A small township and associated services have been constructed for employees at Green- Vale.

Jan 1, 1974

By Y. L. Su, R. Stefanko, Y. J. Wang

This chapter describes a new approach to the solution of stress distribution around underground openings utilizing the finite element method and employing stochastically simulated rock properties. It is well-known from extensive laboratory tests that the properties of rocks, e.g., Young's modulus and Poisson's ratio, are not single-valued but form some distribution. If the scatter of test data is attributed to the variability of the rock itself rather than due to an inadequacy in test procedure, then stress solutions have to consider these variations. Utilizing this basic philosophy, the present study was initiated. A long circular opening subjected to plane strain in a hydrostatic stress field was chosen as a specific example to illustrate this approach. The technique adopted in solving stress distributions was based on the finite element method. This method is essentially a generalization of standard structural analysis procedures in which the continuum is idealized as an assemblage of "elements," interconnected at a finite number of nodal points. It is capable therefore of handling different material properties for individual elements in the model, if desired. In this study, each individual element was assumed to be isotropic, homogeneous, and elastic. However, values for Young's modulus and Poisson's ratio were randomly varied from element to element according to an assumed frequency distribution.

Jan 1, 1970

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of'these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990

By Ritchie I

Copper minerals are often associated with gold ores. These create processing problems since cyanide solutions are not selective for gold alone. Copper minerals are also leached by cyanide, and typically each one per cent of `reactive' copper in the ore consumes about 30 kg t 1 cyanide. Once in solution, copper cyanide species create further processing problems as they adsorb onto carbon along with the dicyanoaurate ion. These problems make conventional cyanidation of gold ore uneconomic if the ore contains too much copper. As a result, methods of economically processing gold-copper ores are becoming of increasing importance.One of the more promising methods of treating these ores is by selective leaching of the gold by an ammoniacal cyanide solution, a method first described by Hunt in 1901. This method is already in commercial use in Mauritania, treating copper/gold tailings. In general terms, the addition of I - 2 g U1 ammonia to a standard cyanide leach solution causes a significant increase in gold extraction and decrease in copper extraction. However, early testwork on this system has concluded that the optimal leach conditions are critically dependent on ore composition, and the mechanism is not well understood, making predictions of best conditions impossible.

Jan 1, 1997

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

By J P. R de Villiers

The Vanderbijl Park sinter plant in South Africa was investigated to determine the reason for the production of very fine sinter not acceptable as feedstock for the blast furnace. A procedure was designed to generate representative samples and to prepare the samples for chemical and mineralogical analyses. Results from a mineral analyser showed that the samples are extremely heterogeneous and therefore the sampling and sample preparation methods had to be tested in order to produce representative samples. The high production capacity at the sinter plant could also give rise to sampling errors. The method designed involved sampling of the conveyor belt at the sinter plant every four hours for the duration of three days. The samples were then milled and split into smaller sections appropriate for analysis. X-Ray diffraction (XRD) and X-Ray fluorescence (XRF) analyses were conducted on the samples. The results showed a standard deviation of less then one per cent, which indicates that the samples were representative and that the method used was therefore adequate. Systematic differences in the phase proportions between normal and fine sinter samples were detected, with the fine sinter containing more haematite than the normal sinter. The sampling method employed gives added confidence that the differences are real.

Jan 1, 2008

By Richard A. Bideaux

In mid-1975, the United States Borax & Chemical Corp., a member of the RTZ group, engaged Computing Associates, Inc. (CAI) in a continuing project to model their operating property at Boron, CA, with the goal of computerized assistance in medium- and long-range open-pit mine planning. Their property, 161 km (100 miles) northeast of Los Angeles, is the largest producer of borate minerals in the world. Because of unusual geological complexity, this unique deposit presents interesting problems in computer modeling, compared with the coal, uranium, and other metallic deposits with which CAI ordinary deals. Mine planning for Boron has historically been based on manually plotted contour plan maps and cross sections, with geological reserves derived from manual triangularization of the drilling pattern. Standardization and reproducibility of log interpretation, contouring, and reserve calculation were principal goals of using the computer. Additionally, it was desired to shorten both the time and cost of a planning cycle, while at least equalling the accuracy of the manual planning. The present recovery plant processes only water-soluble borates; at some time in the future it will be necessary to recover acid-soluble borate minerals as well. With computer assistance the economics of this changeover point can be more thoroughly evaluated.

Jan 1, 1979

By Howard M. Graff, Sidney C. Bouwer

The economics of mining has traditionally been viewed quite apart from the economics of blast furnace operations. It was realized, of course, that blast furnaces would operate best with good raw materials, but the shipping grade of ore, for example, was decided by a sort of collective bargaining process between the ore producers and the blast furnace operators. The mine operators had to keep their costs down, and were usually successful in convincing management that the ore in any particular deposit was endowed by nature with a certain iron content and that the mine grade could not be raised beyond a certain economic limit. The blast furnace operators would have liked a better grade, but as long as they were able to make a fairly good showing it was more or less accepted that they had to take the ore as it came. The mine operators were able to ship to the nation's blast furnaces thousands of tons of iron ore that would be completely unacceptable by present-day standards. As late as the early 1950's, the major steel companies were witnessing an actual decline in the iron content of their incoming ore supply as the mining companies mined progressively leaner material and upgraded it only enough to pass competitive market requirements

Jan 8, 1965

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993