Search Documents

By Arthur P. Nelson

In opening, I want to thank the program committee and members of the Society of Mining Engineers of AIME for the opportunity to speak to you. Various chapters of AIME this past year have expressed interest in the Federal Metal and Nonmetallic Mine Safety Act. We want to see that interest continue, because the reason for the legislation was the safety and health of the industry's workforce. The Department of the Interior was directed by the Congress to administer the provisions of the Act and is therefore held directly accountable for the success or failure of its intent. We intend to see it succeed. Among other things, the Act does provide for education and training under Section 15. This provision has been implemented and is expanding. However, the responsibility of my office is inspection and enforcement and that is my subject today.

Jan 1, 1973

By HENRY COLEMAN

WE as employees of these related companies, I am sure, are proud to be affiliated with them, and have great faith in the sagacity and fore- sightedness of our employers. Most of us here have been called into important positions in these organizations, and it should be our most earnest endeavor to sense and carry them out as if they were our very own. We have been asked to supervise and carry on a work over which our employers cannot personally watch. It has been well said that the most efficient organization is that which requires the least attention from its head. Because of the very nature and condition of our work, which separates us by many miles from our employers and makes it impossible for us to receive attention and instructions from the heads of our departments, save for occasional visits and correspondence, we are given a great opportunity to prove that we can be efficient workers without too much attention from the heads of our departments. There are few employees who cannot do their duty when it is laid before them in specific terms, and when their employers are always there to see that their plans are carried out. But the employee who is really giving efficient service sees his duty himself and willingly does it. '

Jan 1, 1931

By Agnes Ágata Fróes Martins

Placas ósseas metálicas são componentes utilizados para correção ou cura de fraturas ósseas. Em se tratando de implantes ortopédicos, é fundamental conhecer o comportamento dos materiais quando submetidos a esforços mecânicos. Para isto ensaios são realizados baseados em normas técnicas, que no caso específico de placas ósseas, são utilizadas as normas ASTM F382 e ABNT NBR 15672-2. Na execução do ensaio para determinação da rigidez à flexão, de uma placa óssea, pode existir o efeito da flexibilidade do dispositivo de ensaio. Para verificar a magnitude desse efeito, foram realizados três ensaios de flexão estático e um ensaio de flexibilidade do dispositivo de ensaio, onde o ensaio foi interrompido ao final da fase elástica. As propriedades mecânicas da placa foram avaliadas, aplicando a correção da flexibilidade do dispositivo. Os resultados mostraram que para os níveis de carregamento alcançados, as cargas de prova apresentaram pouca influência na flexibilidade do dispositivo, e consequentemente pouca influência na rigidez após os cálculos de correção.

Aug 8, 2018

By R. E. Wagner

MISSOURI's famous lead area, in what is known as Southeast Missouri, is locally termed the "Lead Belt." These deposits are in the Bonne Terre dolomite of late Cambrian age which has a thickness of nearly 400 ft. Underlying this is the La Motte sandstone which varies in thickness from 0 to 400 ft. The La Motte beds are deposited directly on the ancient erosion surface of Pre-Cambrian porphyries and granites of probably Algonkian age. The buried igneous peaks extend up into the Bonne Terre in several areas within the Lead Belt. Overlying the Bonne Terre are shales and siliceous dolomites of late Cambrian and early Ordovician age. Within the Lead Belt these have a thickness of from 0 to 500 ft. The district is bounded in general on the southwest by the Sims Mountain fault, on the northwest and north by the Big River fault, and on the

Jan 1, 1947

By Leonhard Weixler, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep ground-water barriers, named Cut-Off-Walls (COW). It can be anticipated that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Therefore, there is the demand to minimize the size of equipment to accommodate such projects. Following this demand, a new trench cutter system, the so-called CUBE System, was recently developed. The complete trench cutter system has been fit into container size dimensions so that it can work in very limited space conditions. In addition, complex conditions in terms of space limitations require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Due to the limited space requirements, the impact on the surrounding environment is limited. As the system is electric driven, an additional reduction of carbon footprint can be expected. First tests of the system have been carried out and the results will be shared. The paper will explain the construction process and the specific challenges and experiences made for these extreme conditions.

Oct 1, 2022

By E. Watkins, J. C. LeRoy, A. Vivyurka

"TAILINGS REVEGETATIONWelcome to the Revegetation Session. My instructions are to introduce the Speakers and to provide a general introduction.I do the latter with humility not only because of a lack of personal experience or because tailings revegation is not well established technology, but because any general statement on a country or industry as diverse as the Canadian Mining Industry is bound to be wrong somewhere.Laying aside normal standards of accuracy I proceed as follows:In considering the question of tailings revegetation, one asks two basic questions:1. What ought to be done?2. What can be done?The first question can be broken down into three kinds of criteria or objectives:a) Legislativeb) Technicalc) AestheticThe first I leave to the politicians and the last I will avoid. Aesthetics is the philosphy of taste. It is concerned with the appreciation of things rather than what they really are. It is much easier to get into an argument on aesthetics than to get out of it feeling you have said something of consequence.Technical criteria can be divided into the following sub-objectives: 1. To isolate the tailings basin so surrounding land is not degraded. The first step here is stabilization of the surface to prevent wind and water erosion."

Jan 1, 1975

By J. Mothomogolo

Mining projects are capital-intensive and are also characterized by high technical and economic risks. These factors pose challenges to mining entrepreneurs when they seek to raise seed capital for mining start-ups. There are limited sources of mining investment funds in South Africa and each has shortcomings due to one reason or another. Another impediment is South Africa?s status as a developing economy, in which the standards of living ? which in turn influences the savings culture ? the limited GDPs and budget, the socio-political environment, and banking, mining, treasury and other regulations, determine the size of investments, particularly in mining ventures. The proposed funding mechanism was developed with the aim of filling the gaps identified in existing funding mechanisms that were developed by the government with the introduction of the Minerals and Petroleum Resources Development Act (MPRDA), 2002. The shortcomings identified were presented to the study participants as questions to obtain views that were used to define innovative ways of raising mining start-up capital. Most participants in the study supported the derived hypotheses and proposals, and these were used to refine the proposed mechanism for mining investment in South Africa. The proposed funding framework is aimed at encouraging interaction between mining entrepreneurs, government, and the investors to align goals and expectations when undertaking a mining investment.

Jan 1, 2012

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By B Mohanty, G Ludwig

A thorough assessment of development drilling and blasting practice was carried out at two underground mines at INCO operations in Thompson, Manitoba. The study showed that significant improvement in productivity can be achieved through careful selection of explosives and loading practice, and modifications of the standard blast lay-out. The analysis involved assessment of the effectiveness of various perimeter blasting methods, employing selected explosives and loading practice in both jumbo and jack-leg rounds. The blasting pattern as well as burden and spacing were varied to determine their effect on the blast results. The various types of explosives used were, pneumatically loaded ANFO, with and without detonating cord tracing, extra-strength detonating cord, and slurry and emulsion explosives with and without cord tracing. The study also dealt with various means to achieve increased rate of advance in both jumbo and jack-leg rounds. The diagnostic measurements consisted of VOD, 'burn' marks or half-barrels on perimeter wall, and blasting vibrations. The effects of geology, firing sequence, blast lay-out, and drill hole deviation on the final results were also examined. The results of the study have been shown to have very important bearing on the design of development round blasting.

Jan 1, 1998

By D R. Seaman, B Adamson, F Burns, B A. Seaman, P Manton

The Telfer concentrator, located in the Great Sandy Desert of Western Australia, consists of a dual train gold/copper operation processing ore from one underground and, currently, two open pit mines with differing mineralogy. The flotation circuit of each train was designed to operate in several modes depending on the feed mineralogy. The majority of ore mined at Telfer is processed in a sequential mode where copper minerals are first floated into a saleable copper concentrate followed by the flotation of an auriferous pyrite concentrate which is treated in an on-site hydrometallurgical plant (carbon-in-leach (CIL)). Gold is recovered as a gravity product within the primary grinding circuit, to the copper concentrate, and to a lesser extent, the CIL circuit.Since Telfer was re-opened, with a new concentrator, in 2004, the processing plant has struggled with poor copper concentrate grades, partially due to the excessive entrainment of non-sulfide gangue minerals in the copper flotation circuit and, more recently, due to composite copper particles produced when processing ore from a supplementary satellite pit that has not previously been processed through the new Telfer concentrator. Gold recoveries in the CIL circuit have also been below industry standard. This paper presents the implementation of recent changes made to the circuit to address these performance issues. The reconfiguration of the circuit has involved the installation of the following major equipment items: two ISAMillsÖ in ultra-fine grinding applications (one in the copper circuit and one in the pyrite circuit), two Jameson Cells to improve fine gangue rejection and a bank of 5 + Outotec TC30s to recovery copper and gold from the reground pyrite stream. The equipment was purchased direct from vendors and an engineering firm contracted to design and install the multi-vendor reconfiguration upgrade.CITATION:Seaman, D R, Burns, F, Adamson, B, Seaman, B A and Manton, P, 2012. Telfer processing plant upgrade - The implementation of additional cleaning capacity and the regrinding of copper and pyrite concentrates, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 373-382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By Brenda J. Wolfe

Following successful laboratory and pilot plant investigation of dewatering characteristics of molybdenum concentrate produced by a Chilean copper/moly producer, two (2) DENVER SALA 500 Series Tube Press Filters were installed in 1994 to handle the total production volume. Moisture requirements in the filter cake have been consistently met, eliminating the need for thermal drying after filtration. Operating data and Tube Press Filter are described herein.

Jan 1, 1995

By R. G. Reddy

Nickel solubilities in spent pickling solutions (i.e. HF-HNO3-H2O solutions ) were measured as a function of HF and HNO3 acid concentrations. The chemical analysis of the industrial pickling solutions and sludges were made. The stable phases observed in the sludges are FeF3?3H2O, and ( FeCr ) F3?3H2O. Pure Ni, and stainless steel type 316 were used in this study. The results showed that the solubility of Ni increased with increase in concentrations of HF in pickling solution at a fixed concentration of HNO3: An excellent agreement between the experimental solubility data and the theoretical data was obtained. X-ray diffraction analysis showed that the solid solubility product formed is mainly NiF2?4H2O compound.

Jan 1, 1992

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By Richard F. Link, Jr. Koch

"A mathematical simulation model has been devised to guide the layout of surface or underground mine workings, drill stations, and drill holes that are established in order to search for tabular ore bodies. The ore bodies may be contained within veins, sedimentary beds (including reefs), or other tabular structures.Programmed for a time-shared digital computer, the model contains both stochastic and deterministic variables. Stochastic or natural variables include the number of ore shoots and their sizes, orientations, locations and values. Deterministic or controllable variables include (i) locations and costs of workings (for underground exploration); (ii) drill station locations and costs; and (iii) drill hole azimuths, inclinations, lengths and deflections (if any).For various assumptions about the natural variables, the model is run while the controllable variables arc changed deliberately. Thus, layouts are devised to determine the percentages of the total number of assumed ore shoots found at different costs. In order to choose among the various layouts, cost-effectiveness measures are calculated."

Jan 1, 2014

By R. D. Brown

Higher employer costs and increased employee benefits will result from the current sweeping revisions of the un-employment insurance system now receiving consideration before Parliament. The new legislation, the Un-employment Insurance Act, 1971, will substantially increase the unemployment insurance costs of many employers through an increase in the level of employer contributions -generally, employer contributions will go to 1.4 times employee costs -as well as by extending coverage to many classes of employees now exempt. Under the new legislation, executives, technicians, teachers, institutional workers and others will be covered, and eligible for the higher benefits which it provides. For the first time, absence from work because of illness or accident may qualify individuals for unemployment insurance benefits.

Jan 1, 1971

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By Joel Chipana, Roberto Laredo, Benjamin Cebrian

Ring blasting is a common production method in underground metal mines. As a drill and blast process, it presents particular features that do not correspond with bench blasting in open pit or underground mining.

Jan 1, 2017