Search Documents

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Roger A. Blais, Michel David

"Matheron&apos;s geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world&apos;s future needs for minerals - the needs which it is our industry&apos;s task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world&apos;s mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world&apos;s demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth&apos;s crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974

By Frederick K. Allgaier

This is the first in a series of progress reports on the longwall subsidence research program at the Bureau of Mines Denver Research Center. As part of this program, the Bureau and the Utah Power and Light Co. are cooperating on a study conducted at the Deer Creek Mine, which is directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. A monitoring network has been established at the Deer Creek Mine to measure subsidence over four adjacent longwall panels. To date, two panels have been mined. Subsidence began as the first panel was mined and continued for 1 year following completion of the panel, during which time the adjacent panel was mined" A maximum of 2.7 feet of subsidence occurred over the two longwall panels mined at a depth of 1,500 feet. Because of the length of time that subsidence continued after mining, the final subsidence profiles and angle of draw have not yet been determined.

Jan 1, 1982

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By F. G. Horino

The Bureau of Mines conducted compressive strength tests on model pillars of selected rock types with each pillar containing a critically oriented plane of weakness. The objective of these tests was to determine if a significant increase in the strength of the model pillar could be obtained by either (1) installing tensioned rock bolts through the pillar and normal to the plane of weakness, or (2) wrapping tensioned steel wire ropes around the pillar at uniformly spaced intervals along the pillar. Equations based on Coulomb&apos;s failure criterion are developed to predict uniaxial compressive strength of model pillars that are either rock-bolted or wire-roped. Laboratory compressive strength tests on unbolted and bolted model pillars of sandstone, marble, Indiana limestone, and oil shale containing a plane of weakness oriented at 45° showed that the bolted pillars are stronger than the unbolted pillars by 84, 31, 52, and 28 pct, respectively. Laboratory compres-sive strength tests on nonroped and roped model pillars of Texas limestone, sandstone, and granite containing planes of weakness showed that the roped pillars were stronger than the nonroped pillars by factors ranging from 1.01 to 2.41, depending upon the angle of the plane of weakness and the rock type. Rocks with a low Young&apos;s modulus benefited most by the wire-roping technique.

Jan 1, 1971

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Gary L. Seider, Dana A. Wesolek, Fred C. Schmednecht

"A new condominium project, The Atelier, developed by Pickus Companies located at the corner of Bryn Mawr and Sheridan in Chicago, IL required an earth retention system to protect the surrounding roads, alley, and existing neighboring apartment bui lding during its construction. Slurry Systems, Inc. (SSI) and Ground Engineering Consultants, Inc. designed the earth retention system using cantilevered sheet piling for three of the four sides: two sides bordering major streets and one side bordering an alley. For the fourth side, which borders an existing occupied brick building, a combination of sheet pil ing and AB. CHANCE® helical screw piers were used. SSI was actively involved in the review process of its earth retention system with the City of Chicago and quickly learned that there was no specific code for hel ical piers/anchors. (It appears that this is the case with most metropolitan cities throughout the United States). Consequently, the approval of underpinning for this project became the critical path, as much testing, calculations, meetings, and other details were required prior to its approval.SSI and AB. CHANCE® recognized that this process for underpinning approval must be seen by other contractors/suppliers who wish to use helical piers/anchors in the City of Chicago. Consequently, this project served as an opportunity to work with the City of Chicago and the City's Building Code Committee in furthering the development of the Helical Piers/Anchors Code, Section 1814. INTRODUCTION - HELICAL PIERSDefinition. A helical pier or anchor consists of one or more helix-shaped steel bearing plate(s) attached to a central steel stem (solid bar or pipe), which is installed by rotating or ""torquing"" into the ground. Each helix is attached near the tip, is circular in plan , and is formed into a screw thread with a defined pitch. Helical piers/anchors are pre-fabricated and can derive their load-carrying capacity through both end bearing and skin friction. The helical piers/anchors can be augmented with grout."

Jan 1, 2005

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By III, Peter J. Rogers, J. Gordon Ogden

A study is described which attempts to identify the chemical factors of common concern to environmental and exploration geochemistry as indicated by recent work in both disciplines in Nova Scotia. Cores taken in lake sediments define geochemical baselines for the modern and pre-industrialisation periods. The investigation of lake and stream drainage indicates the presence of numerous chemical and organic factors that can be attributed to man's activities, such as construction and energy consumption. Geochemical surveys of lake and stream sediments are used to locate potentially toxic, high risk areas in Nova Scotia. Rapid change occurs in most surface drainage systems with the possibility of numerous chemical reactions taking place. It is found that spatial and temporal variations in the chemistry of modern and recent sediments are of interest to exploration and environmental surveys.

Jan 4, 1992

By Brianna M. Eiter, Jennica L. Bellanca

Mineworkers face a challenging and dynamic work environment every workday. To maintain a safe workplace, mineworkers must be able to recognize worksite hazards while they perform their jobs. Though hazard recognition is a critical skill, recent research from the National Institute for Occupational Safety and Health (NIOSH) indicates that mineworkers fail to identify a significant number of hazards. To further the understanding of mineworkers’ hazard recognition ability and to begin to address hazard recognition performance, NIOSH researchers analyzed data collected during a laboratory research study to determine the effect of individual mineworker factors including risk attitude, work experience, and safety training on hazard recognition accuracy. The results of this study show that mineworker risk attitude and safety-specific work experience affect hazard recognition performance while hazard-specific safety training does not. These results suggest that some of these individual factors can be overcome through experience and training. Potential strategies that can be used to address these factors are also discussed.

Aug 31, 2020

By S. Schutte, J. Pelders, F. Magweregwede, S. Ngobese, W. Botha

A people-centric, systematic approach that involves different stakeholders is considered necessary to successfully address changes associated with modernizing the South African mining industry. In this paper we discuss the inclusion of various South African mining industry stakeholders, particularly the employees, in equipment design and development processes. Data was acquired through a literature review and inputs from South African mining industry stakeholders through focus group discussions, interviews, and an online survey. It was suggested that some of the areas that could be improved by the inclusion of employees in the process are design quality, ergonomics, equipment acceptance by the workforce, safety, efficiency, skills, insight into context of use, and early design iterations and identification of problems. Among the issues considered to be barriers to inclusion were lack of buy-in, lack of resources, difficulty in manufacturers accessing the mines, difficulties in involving too many people, intellectual property concerns, and unavailability of mine employees due to their key responsibilities. Identified critical factors in the equipment design and development process include iterative design, stakeholder participation throughout the process, needs analysis through consultation, and change management. A guideline was developed for worker inclusion in equipment design and development that could be used by the South African mining industry. The study identified several economic and social benefits of including stakeholders in the early stages of design and development. It is recommended that the South African mining industry considers using the developed guideline.

Apr 5, 2023

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract -A test survey using the MEGATEMII airborne electromagnetic system was flown over the Iso and New Insco massive sulfide orebodies in the Rouyn-Noranda mining camp, Canada. The results were compared with data from historical systems (INPUT, DIGHEM) used to discover the deposits. The historical data show that the two deposits have comparable conductances. However, the modern MEGATEMII system reveals that the New Insco deposit has a much slower decay than the Iso deposit, and it is, therefore, interpreted to be more conductive. The MEGATEMII anomaly maps provide estimates of the location, depth, dip, and strike of the two deposits, information that was not available from the historical anomaly maps. The signal-to-noise ratio of the MEGATEMII data is greater than the historical data, yielding more sharply defined anomalies. The investigations also included a comparison between 90 Hz and 30 Hz MEGATEMII data. The 90 Hz data were found to be useful for mapping the less conductive parts of the Iso body, whereas the 30 Hz data demonstrated that the New Insco body is more conductive. Analysis of height attenuation data over the Iso body indicates that the body could be seen by the MEGATEMII system if it were buried an additional 230 m deeper (in highly resistive material). On the other hand, the INPUT system would detect the Iso body only if it were buried no deeper than an additional 60 m. Tests with the transmitter turned off showed that, for this flight, the MEGATEMII system noise levels on the processed data are about 300 pT/s. Sommaire - Dans le cadre d’un projet de recherche, un ensemble de levés d’essais électromagnétiques aéroportés employant le système de MEGATEMII a été effectué au dessus des dépôts d’Iso et de New Insco, Rouyn-Noranda, Canada. Les données ont été comparées avec les réponses des systèmes qui ont découvert ces deux dépôts (INPUT et DIGHEM). Les données antérieures montrent que le dépôt d’Iso a une conductance comparable à celle de New Insco. Cependant, les données de MEGATEMII démontrent que le dépôt de New Insco a une haute valeur de la constante de décroissance, ce qui reflète une plus forte conductivité. La carte d’anomalies de MEGATEMII indique la localisation, la profondeur, le pendage et l’orientation des deux dépôts, ce que la carte d’anomalies antérieure ne montrait pas. Le rapport de signal à bruit de MEGATEMII est plus grand que celui des données de INPUT et de DIGHEM; de plus, les pics sont mieux définis. Les tests ont également permis une comparaison entre les fréquences de base de 90 Hz et de 30 Hz. Les données de 90 Hz se sont montrées utiles pour cartographier la partie du dépôt Iso dont la conductivité est la plus faible, tandis que les données de 30 Hz montrent clairement que le dépôt de New Insco est plus conducteur. Les analyses de l’atténuation du signal avec la hauteur ont indiqué que le dépôt d’Iso pourrait être détecté par le système MEGATEMII s’il était enfoui à 230 m sous la surface (dans un milieu hautement résistant). D’autre part, le système INPUT pourrait seulement détecter le dépôt d’Iso s’l était situé à 60 m de profondeur. Les tests avec l’émetteur fermé démontrent que le niveau de bruit est des l’ordre de ±300 pT/s."

Jan 1, 2006

By C. H. Schack, K. C. Dean

An investigation was made to devise and evaluate a flexible flotation method for beneficiating typical tactite types of calcareous scheelite - bearing ores ; these scheelite - bearing ores are available in large tonnages in deposits containing 0.2 to 0.3 pct tungsten trioxide . The objective was to achieve a high recovery of the tungsten in concentrates , containing a minimum of 10 pct WO3 , that would be suitable for chemical processing into high- quality synthetic scheelite . The principal problems encountered and resolved by bench- scale flotation tests on ore samples from five different deposits were to define the conditions and reagent combinations essential for ( 1 ) achieving selective flotation of a small amount of scheelite from a large amount of calcite and ( 2 ) controlling the effect of small amounts of calcium , magnesium , and iron salts in the ores and water used . The flotation process was evolved from batch tests and continuous runs in a pilot - scale mill with a capacity of 100 lb per hour . The flotation process comprised ( 1 ) removal of sulfide minerals , ( 2 ) conditioning the residual ore pulp with sodium carbonate , quebracho , and trisodium phosphate , and ( 3 ) rougher flotation and single - stage cleaning of a scheelite concentrate . In a pilot plant run , over 91 pct of the tungsten was recovered from ore containing 0.27 pct WO3 , in a concentrate containing 11.2 pct WO3 .

Jan 1, 1964

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011