Search Documents

By T. Orser

In 2010 Newmont made the decision to purchase a 42 foot (ft) Semi-Autogenous Grinding (SAG) mill from Metso and a 28 Mega-Watt (MW) Gearless Mill Drive (GMD) from ABB for the Conga Project in Peru. The test and study work showed that a single line 42 ft SAG mill circuit gave the most favorable project economics in comparison to an equivalently powered single line 40 ft SAG mill circuit. This paper does not address the process design or the project economics, but instead focuses on the key aspects of the SAG mill design, GMD design and the associated component manufacturing. This paper also addresses, where applicable, the potential reliability differences between the initially proposed 40 ft SAG mill and the finally accepted 42 ft SAG mill.

Jan 1, 2012

Duties on Lead Imports from Mexico. - On September 15, the President signed Proclamation 4792 suspending concessions formerly granted as of January 1 on red lead imported from Mexico. The Proclamation also increased the duty payable on litharge imported from Mexico from 3% ad valorem to 3.5% ad valorem, effective September 15. Appeal of Lead Standards. - The U.S. Court of Appeals for Washington, D.C., rejected petitions by the Lead Industries Assoc. and St. Joe Minerals Corp. for a review of standards promulgated by EPA and OSHA. The Lead Industries Assoc. reportedly will appeal to the U.S. Supreme Court on the basis of the "benzene" and "cotton dust" decisions. Scheduled implementation of standards will continue during the appeal.

Jan 1, 1980

The XVIth International Conference on Coal Mine Safety Research was divided into eight half-day technical sessions. In accord with the established practice of these conferences, at each session, presentation of the papers was followed by a discussion period. Questions and comments submitted in writing to the session chairman were answered or discussed by the authors of the relevant papers or by their representatives. These discussions were tape-recorded in the original language of the speaker and subsequently translated into English when necessary. Questions to which no answer was available at the time and a few comments that exceeded the scope of the session have been omitted.

Jan 1, 1975

By Frank Pepe, Nestor Garavelli

The 2023 Rapid Excavation and Tunneling Conference (RETC) will be held in Boston, MA and will include the presentation of 133 papers divided into 20 technical sessions during the 3 day conference that were selected from over 200+ papers that were submitted to the committee. The selected papers are included within this book to provide a comprehensive recap of the conference while also providing a source of reference for contractors and engineers in the future. The selected papers will include contributions from all divisions of the tunneling industry plus risk management and best contract practices. Boston is known to the tunneling industry for its complex and difficult tunneling history, specifically of recent memory the Central Artery/Tunnel Project also know as the “Big Dig” of the 1980s and early 1990s. The selection of Boston as a host city was fitting from a historical perspective and as avenue for the city to present its upcoming tunnel projects. RETC began in 1972 with the idea of sharing ideas, design and project construction experience, and new technology, between contractors, designers, owners and suppliers. The ability to provide a single location every other year for all facets of the tunneling industry to gather and discuss the aforementioned was and still is viewed as a way to help the tunnel industry grow. The lessons learned from completed projects, the advancement of technology which could be implemented into design and the presentation of new projects by owners/designers and contractors allows for the limits and complexity of upcoming projects to be expanded beyond our current capabilities. Our industry has never been as busy as it currently is, and we are seeing more future projects coming out for solicitation across all business sectors. With the good fortune that all of us have been blessed with one of the biggest challenges that we have been faced with is the shortage of future management on all levels for our projects including the labor force. We all want our industry to continue to grow and succeed, our most important assets are the people that we employ. Investing in the education and continued training of our work forces to be up to date with the latest technology and methods is the key to our success. This also includes develop, recruiting and mentoring of young students graduating college to join our industry so that we can all continue to grow. We hope that all those attending the conference will have the ability to attend as many sessions as possible and to expand their network within our industry. As in past years, scholarship students will be in attendance and we encourage all to offer these students an opportunity to visit jobs, attend learning sessions or future internships to expand their interest in our industry that needs an injection of young engineers to contribute and lead our future Rapid Excavation and Tunneling Conferences. The program chairs wish to thank the session chairs, co-chairs, authors, and other members of the RETC Executive Committee for their dedication to this conference. Last but certainly not least, we give special thanks to the SME staff for their hard work and enthusiastic support in making this conference possible.

Dec 1, 2023

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

By K. K. Kelley

The first bulletin (269) 3 in this series, which appeared in 1932, compiled the entropy values then available for the elements and in-organic compounds, results being listed for some 150 substances. Elaborations and revisions followed in 1936 (272) and 1941 (280), when over 500 usable entropy values were tabulated. The present bulletin constitutes a further elaboration and revision. The accumulation of data since 1940 has been marked, and 800 entropy values now are available. The present bulletin also contains all the pertinent explanatory matter that appeared in its predecessors. Thus, it retains the same dual purpose of assembling the available values of the entropies at 298.16° K. of the elements and inorganic compounds and giving enough explanation of methods of calculating entropies to make the results comprehensible.

Jan 1, 1950

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By M. Peters, P. Schmäh

The development of renewable energies and a sustainable power grid are the challenges for future energy supply. Underground cables will replace the vulnerable overhead lines, because of their safety benefits. Due to the public environmental awareness, smart tunnelling and trenchless solutions are required for inner-city and cross-country installations of underground cables, as well as for crossings and the landfall sections to connect offshore wind farms to the transmission grid. Methods from the tunnelling and pipeline industry provide a high flexibility in the planning of alignments, including versatile tunnel concepts and the installation of protective pipes with E-Power Pipe and Direct Pipe.

Jun 13, 2023

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By Sarkis G. Ampian

Published optical microscopic and X- ray diffraction characteristics of the following compounds are critically evaluated and compared with Bureau of Mines data : Tricalcium aluminate , calcium monoa luminate , dodecacalcium heptaluminate , dicalcium silicate , tricalcium silicate , and sodium aluminate . A recommended set of definitive optical and X- ray diffraction characteristics is presented . These values are used to identify products of the lime soda sinter process for production of alumina . Polymorphism of gamma- , beta- , and alpha prime - dicalcium silicate is reexamined , and new data are presented on polymorphism of tricalcium silicate and sodium aluminate by high- temperature X- ray diffractometry . Polymorphism is not observed for tricalcium aluminate , calcium monoaluminate , and dodecacalcium heptaluminate . Bureau of Mines data indicating a stoichiometry of 12Ca0.7A10 for the phase 5Ca0.3A1 0₂ are discussed . A critical review of the literature concerning calcium dia luminate and sodium undecaluminate ( 8 -A10 ) is also included .

Jan 1, 1964

Only West Australian entrepreneurs and Queensland politicians generate more debate than the uses and abuses of expert reports. Indeed, there are 300 of us here today to debate the very issues that, in general, have been unsatisfactorily managed by regulators and industry to date. I imagine Trevor Sykes will have some interesting stories to tell tomorrow morning in describing "Mines that weren't quite".

Jan 1, 1989

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By Darold Woodward, Stefan Haydn, Petr Pospisil

Most fatalities in tunnel fires are caused by the spread of toxic smoke. Controlling the spread of smoke is crucial to provide a survivable environment for emergency egress. A properly designed and tuned feedback control loop is required to achieve a target flow that is slow enough to allow pedestrians to escape under different boundary conditions. Feedback control loops are also helpful in optimizing energy consumption under moving traffic conditions. A reliable feedback flow control system requires sophisticated engineering knowhow and experience, careful selection of instruments and controlled variables, and thoughtful implementation from design through field testing and commissioning.

Dec 1, 2022

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017

By K. C. Dean

A semiquantitative test for the presence and identification of cesium and rubidium in rocks, clays, and mineral waters has been developed by the Bureau of Mines. The test can be used in the field, as a guide for the prospector, geologist, or mining engineer engaged in location or development [w]ork. It comprises two simple spot tests of a solution prepared from the [m]ineral sample. Phosphomolybdic acid, added to a drop of the test solution, [d]etects cesium, rubidium, and potassium in quantities as low as 60 parts per [m]illion. Silicomolybdic acid, added to a second drop of test solution, enables the operator to distinguish between cesium and/or rubidium and potassium. Test procedures, equipment requirements, and limitations of the method are described in this report. Cesium and rubidium were discovered in 1860 and 1861 by Bunsen and Kirchhoff with a spectroscope. The elements usually occur together, particularly in granite and granitic pegmatites. Rubidium does not occur as an essential constituent of any known mineral, yet it is found as a minor element in so many minerals that rubidium is 16th in abundance in the earth's crust. Cesium, which ranks as the 37th most abundant element, is the principal component of pollucite and a minor element in a wide variety of minerals.

Jan 1, 1960

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

By Louis J. Sousa

In November 1989, the U.S. Bureau of Mines sponsored a 2-day conference to stimulate thinking and discussion about changing materials technologies and implications for the Government's materials information programs. On the first day of the conference, speakers provided overviews of developments occurring in each of the major materials groups. Emerging technological developments, applications, economic and national defense significance, intermaterial competition, and potential market growth in advanced plastics, polymer composites, ceramics, metals, and electronic materials were described. In general, the speakers forecast advanced materials market growth rates in excess of overall gross national product (GNP) though high costs will tend to limit growth outside of aerospace, defense, electronics, medical equipment, and other typically high value-added businesses. On the second day, a wide range of speakers representing several facets of the materials community described how advances in materials technology are creating a need for new types of data, statistics, information, and analysis. Reflecting the speakers' broad range of organizational, professional, and personal perspectives, an array of information needs was identified. Most requirements, however, seemed to fall into one of five major categories: Federal materials research activities, material standards, market and economic information, health and safety, and public policy.

Jan 1, 1990