Search Documents

By M. P. Amsden

"Ecstall Mining is a wholly-owned subsidiary of Texas Gulf Sulphur at Timmins, Ontario. The mill tonnage is 10,000 tons per day of two different ores, a copper zinc ore and a silver lead zinc ore, producing about 2400 tons of concentrates per day. These are as a copper concentrate, a high silver zinc concentrate, a low silver zinc concentrate and a silver-lead concentrate. For flotation recovery a very fine grind is required, about 80% minus 325 mesh and the concentrates produced are 40% minus 10 microns.The thickened concentrates are pumped to the filter floor for filtering and drying. The filtering and drying section is separated from the flotation section by a wall and is controlled from a dryer control room by one operator.Two operating panels are located in this control room. One contains stop-start controls for the thickeners, filter motors and vacuum pump motors, and stop-start controls for dryer feed conveyors and dryer product conveyors to concentrate load-out bins, as well as ammeters for conveyor drive motors. Dryer throughput is regulated by Merrick Type L weightometers located on the dryer discharge conveyors and recorded on tons per hour strip charts.The second panel contains the temperature strip charts, furnace drive ammeters, scrubber and exhaust gas controls, burner controls and panel alarms for the four dryers.Filtered concentrates are dried in Nichols-Herreshoff, multiple hearth, dryers consisting of nine hearths (zinc) and seven hearths (copper and lead). There are two dryers for handling zinc concentrates and one each for copper and lead concentrates. The dryers are heated by burning natural gas. Each zinc dryer handles 1,000 t.p.d. and the copper and lead dryers 750 t.p.d. each.Multiple hearth dryers are unusual in the base metal mining industry and the reasons for selecting them in preference to rotary dryers are as follows:1) The concentrates could only be filtered to 15 to 17 percent moisture. These sloppy filter cakes would be extremely difficult to handle in rotary dryers."

Jan 1, 1972

By P. Piga, O. Sammarco

There is a markedly increasing tendency to design deeper and deeper mines, to use larger amounts of explosive per round, to increase the advance rate of the excavations and so the natural ventilation tends to be more intense in the new mines. For this reason, the mines that make use of powerful mechanical ventilation should also take into account such factors as natural ventilation pressures, especially in the case of mines excavated in high-temperature rocks for which natural ventilation is particularly intense. The results of the studies reported here refer to a very hot mine excavated in an area with a high geothermal flow (the Boccheggiano - Campiano mine, southern Tuscany). At various external temperatures, experimental measurements and analyses have been made of the trend of the thermodynamic characteristics of the ventilation air and of the trends of the air/rock heat exchange along the downcast shaft and along the upcast shaft. These data were then used to work out approximate values of the corresponding natural ventilation pressures. After having identified the most conspicuous variations of the thermodynamic parameters of the ventilation air and the factors causing them, an assessment was made of the repercussions they have on the air flow rates and, above all, on the climatic conditions of the underground excavation sites. The natural ventilation pressures were found not to be constant in time; indeed they change continously and it is difficult to predict the changes. Moreover, it was found that their influence on the ventilation of a section of the mine network is greater if the effect of mechanical ventilation on that section is weaker. In the mine section where the measurements were carried out, some portions were found where the ventilation could become insufficient as a result of the effects of natural ventilation pressures. Finally, some guidelines to be followed in designing hot mines have been put forward which ensure efficient ventilation throughout the network at times with the aid of the natural ventilation pressures, which in certain circumstances may reach very high values in mines of this type.

Jan 1, 1987

By L. B. Lindemuth

To those who are in a position to carry the thought to a conclusion; I would like to present a theory for the cause of blisters in galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered because the reason for their formation is entirely obvious. Blisters that occur periodically with no apparent system of ocation, number, size or grouping, and then disappear with no. apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pressure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or washing and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening where it entered as moisture.The pressure so generated forces the sheet apart along those lines of lamination ;hat may be found in practically all flat sections of steel rolled comparatively cold. The increase in volume. from moisture to steam at 800° F. is 2244 times the original volume of the moisture. The pressure generated by ;he moisture heated to 800° F. and entirely confined would be enough to expand or explode any container. This would explain the source of sufficient pressure to cause a sheet to blister.

Jan 3, 1927

By Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (d) of the liquid-to-solid transfer at each temperature has been derived: d = ZLXL(XL - P) + Zsxs(P- ZL(XL - P) + Zs(P - Xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, XL and xs are the composi-tions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under considera-tion. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d -versus-temperature curves for two alloys Pl and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid FIG. I.-GENERAL SOLID SOLUTION DIAGRAM SHOWING S CURVES FOR ALLOYS P1 AND P2. phase only at the temperature of the be-ginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate tem-perature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1940

Foreword—H. Foster Bain........................ 7 Officers and Committees......................... 9 PAPERS Growth of Metallic Crystals. By C. H. Desch...............13 Aluminum Castings of High Strength. By R. S. Archer and Zay .Teffries (With Discussion).............................35 Constitution of Alloys of Aluminum, Zinc and Tin and Aluminum, Zinc and Cadmium. By V. Jares.......................65 Exudations on Brass and Bronze. By W. B. Price and A. J. Phillips (With Discussion)..................•..........80 Preparation of Metallic Single Crystals and Twinning in Zinc and Zinc Single Crystals. By 0. E. Romig (With Discussion).............90 Plastic Deformation of a Zinc Single Crystal. By S. L. Hoyt (With Discussion) 116 Plastic Deformation of Coarse-grained Zinc. By C. H. Mathewson and A. J. Phillips (With Discussion)......................143 The Solidus Line in the Lead-antimony System. By E. E. Schumacher and F. C. Nix (With Discussion)........................195 Note on the Distribution of Energy in Worked Metals and the Effect of Process Annealing Temperature on the Final Annealing Temperature of Fine Copper Wire. By L. Zickrick and R. S. Dean (With Discussion)........207 Note on the Relation of Annealing Temperature to Conductivity of Copper Wire. Ry J. C. Bradley (With Discussion)..................210 Beryllium-copper Alloys. By W. H. Bassett (With Discussion)........218 Some Comparative Properties of Tough Pitch and Phosphorized Copper. By W. R. Webster, J. L. Christie and R. S. Pratt (With Discussion).....233 A Study of the 470" C. Transition Point in Cast 60:40 Brass. By Frances Hurd Clark (With Discussion).......................253 Strldy of the Heat Treatment, Microstructure and Hardness of 60:40 Brass. By Frances Hurd Clark (With Discussion)...............276 Corrosion and Physical Properties of Some Alloys of Aluminurn, Zinc and Tin. By N. 0. Taylor (With Discussion)..................302 Equilibrium Relations in Al-Mn Alloys of High Purity. By E. H. Dix, Jr., and W. D. Iieith (With Discussion)....................315 Deformation of an Aluminum Alloy by a Constant Load. By C. B. Sadtler and J. L. Gregg (With Discussion)....................336 Still Casting of Metals. By P. H. G. Durville (With Discussion).......343

Jan 1, 1927

By E. C. Roberts

TO facilitate some recent microscopic investigations it was necessary to devise special mounting techniques for the polishing of two quite different metallographic specimens. These techniques are extremely simple and are submitted for whatever value they may be to other investigators. The first specimen mount proved very satisfactory for the study of untempered martensite. Since it was undesirable to heat the specimen, lucite or bakelite mounting materials could not be used in the conventional manner. A cold mount was made by drilling a hole of the same diameter as the specimen in a cylindrical piece of polystyrene then press- ing the steel specimen into the hole on an ordinary vise. A prefabricated disk of lucite should work equally well. The only precautions necessary are that the hole be drilled out cleanly and the piece of steel be pressed into the plastic uniformly, otherwise the mount will crack. The second type of mount was required for the study of slag specimens by reflected light. Mounting these specimens in bakelite and then attempting to rough finish the surfaces on graded emery papers resulted in a considerable amount of chipping and breaking out of the slag particles. This made further satisfactory polishing almost impossible. It was found, however, that if the bakelite-mounted specimen was first rough finished to a point where a good specimen surface became visible, the interstices in the specimen surface could be filled and the polishing completed. This filling was accomplished by placing a small amount of lucite powder in the bottom of the steel specimen mold then reinserting the bakelite-mounted specimen on top of the lucite powder. Reheating the mold to the proper temperature and applying the required pressure resulted in the formation of a thin disk of lucite on the bottom of the bakelite specimen. By carefully grinding the lucite away a uniform surface including the slag specimen was obtained and further polishing was unhampered by slag disintegration.

Jan 1, 1951

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by "remote control" mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation. In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term "communications ' as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the

Jan 1, 1981

The following additional studies are recommended: 1. Future development of the magnetic sludge process should involve optimization of the process variables; these include stirring rate, sludge heating time, aeration rate, method of preliminary sludge dewatering, and the effects of magnetic separation for final sludge processing. In addition, the matter of amenability of coal mine waters to treatment should be considered more thoroughly by means of a more comprehensive literature review as well as actual tests on mine drainage samples. 2. The technique of sludge freezing should be explored further. Emphasis should be given to conservation of energy in the process, and the filtration characteristics of the resulting sludges should be evaluated. 3. Further studies should be conducted on the feasibility of the CO2-addition approach to mine drainage sludge densification. The filtration characteristics of product sludges should be evaluated, and the possibility of recovering and recycling the residual alkalinity of the sludge, either directly as CaCO3 or as CaO plus CO2 after calcination, should also be explored further. 4. Efforts should be made to develop cost data for the conceptual processes involving magnetic sludge formation, sludge freezing, and C02 pretreatment, with the purpose of selecting at least one of these processes for further testing at a field site. 5. The use of inexpensive waste materials (e.g. fly ash, "red dog," slag) as sludge additives, possibly in conjunction with coagulant aids, should be considered further. Results of the present studies have indicated that such materials, employed in relatively large amounts, increase the density and enhance the filterability of sludges from lime neutralization of coal mine drainage. The use of pulverized blast furnace slag in this regard appears particularly promising, and studies should be made to ascertain its availability, relative cost, residual alkalinity, and behavior as an additive in conventional mine drainage treatment processes involving lime neutralization and aeration.

Jan 1, 1971

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922

By Samuel Hoyt

THIS paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use.

Jan 1, 1928

By Albert R. Ledoux

I am indebted to The Kaolin Co. of West Cornwall, Conn., and particularly to its engineer, Mr. M. Wanner, for permission to make public, through the Transactions of the American Institute of Mining Engineers, the interesting results of his experiments, having in view the winning of kaolin from deep deposits without shaft-sinking or removing of the overburden. So far as I am aware, nothing like it has been accomplished heretofore, although it reminds one of the methods successfully employed in Louisiana for the winning of sulphur from deep beds by the sinking of pipes one within another, injecting superheated steam under pressure through one pipe, the heat of the steam liquefying the sulphur and the pressure forcing it up through the other pipe to bins at the surface. The kaolin-deposit at West Cornwall is an alteration in situ— that is, it is not sedimentary. A series of clay-veins, dipping about 50" from the vertical, lie between a foot-wall of' limonite and a hanging-wall of gneiss and hornblende schist. The clay-veins alternate with veins or seams of more or less broken quartz, and unaltered feldspar. The deposit, which occurs at a point about 600 ft. above the Housatonic river, was opened five years ago, and about 5,000 tons of a superior grade of washed kaolin have been extracted from open pits, and sold. It soon became evident that this mode of extracting the product would prove unremunerative, by reason of the dip of the vein and the intercalary strata and lenses of quartz, and a more satisfactory method of working the deposit was sought. It is well understood that, in the preparation of all clays for market, especially residuary kaolin, the most important as well as the most difficult step is the washing of the crude product. The dificulties increaee with the percentage of foreign matter, especially quartz and mica, contained in the product. Hence, a system

Jan 1, 1907

Australian wheat belt agriculture is causing a decline of its natural resource base. The major problem, salinity, arises from a small reduction in water consumption by agricultural crops compared to what prevailed under the prior native vegetation. This causes groundwater accumulation which, in the low relief landscapes of the wheat belt, is leading to extensive surface saturation in low landscape positions and dramatic, destructive change in the hydrological behaviour and habitat of streams and rivers. The ability of agriculture to invest in salinity control is severely limited by its long-term decline in its terms of trade. Extensive planting of perennial vegetation has the potential to increase water use and arrest the salinisation process. If these perennials were also commercially attractive, the cost of salinity treatment could be minimised. Given the difficult commercial position of food commodities, it is logical to develop ænon-foodÆ perennial crops, in particular woody crops suitable for industrial products. This paper looks at the example of Sweden, where there has been a generation of investment in developing forest harvest residue recovery, and short cycle woody crops for bioenergy, but with only limited success. In contrast, secondary residues (processing wastes) from forestry industry are readily saleable for low value uses like bioenergy. This suggests that the model woody crop must have a higher value fraction to facilitate delivery and commercial use of its lower value fractions. This model is being emulated in the development of native mallee eucalypts as short cycle woody crops in Western Australia. Some $50 million has been expended on mallee development in the past decade and this has culminated in an engineering demonstration of integrated processing. The putative high value products are activated carbon and eucalyptus oil and the residue (plus waste heat) will be converted to electricity. The potential scale on which crops of this type would be required to achieve salinity control means that many more high value and residue products will have to be developed. Metallurgical charcoal appears to be a promising product option.

Jan 1, 2006

By Walter O. Snelling

In combating mine-fires the use of carbon dioxide as a means of producing an atmosphere in which combustion cannot be sustained, has been many times suggested and frequently tried, generally with a fair degree of success. The carbon dioxide is produced by acting on limestone with dilute sulphuric acid, large wooden boxes being used to hold the limestone, and arranged in such a manner that one box may be cleaned and refilled with blocks of limestone while another is being used in generating the carbon dioxide.. The gas is led by means of pipes of large diameter to the location of the fire, tight brattices having been previously put up as close to the fire as possible on every side, so as to limit the space to be filled with the gas to the smallest possible volume. The cost of producing carbon dioxide has been, however, a decided draw-hack to the use of this method, and the danger of producing carbon monoxide by the reduction of the carbon dioxide by heated carbon, and consequently bringing about an explosion, has also tended to prevent the application of this method. The use of sulphur dioxide in combating mine-fires has not, I believe, been previously suggested or tried, and yet the method presents such decided advantages over the use of carbon dioxide that it seems proper to suggest the advisability of considering it as a cheap, convenient, and safe means of fightr ing stubborn mine-fires. 1. Cost, Preparation, etc.—One ton of brimstone, costing from $20 to $30, will produce about 25,000 cu. ft. of sulphur dioxide gas, and allowing for all sources of loss it is probable that sulphur dioxide gas can be produced for about $1,300 per 1,000,000 cu. ft. For carbon dioxide gas, produced by the action of sulphuric acid on limestone, a good estimate would be $4,000 per 1,000,000 cu. ft., provided that sulphuric acid

Jan 1, 1909

Discussion of the paper of L. O. HOWARD, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1785 to 1790. E. P. MATHEWSON, Anaconda, Mont.-I would like to add a few words of praise on Mr. Howard's work at the Old Dominion. Mr. Howard has given this particular converter shell his personal attention, and the results are shown in the figures given. Similar converter shells, a little different in shape and of about the same size, have been tried in many plants throughout the United States. The results have been highly satisfactory, but there is no shell of the size of the one described by Mr. Howard that has given anything like the results that Mr. Howard's shell has given. I know of larger shells that have given very good service, and are still in operation, and require very little repair. The main thing about the whole process of using the basic lining in copper converting is to keep the temperature within reasonable bounds, particularly not to get the furnace too hot. If it is overheated a little bit, for say half an hour, an entire lining may be ruined. It is very easy to keep the temperature regulated 'if the mass is large. If you have a large mass in your converter you can easily prevent it from getting over-heated, and that is the big argument in favor of the extra large converters. Of course, there is a limit to what a plant can turn out in the way of matte. Very few plants can supply matte sufficient to keep a converter of 20 ft. in diameter in operation constantly, but the 20-ft. converter is very much superior to the 12-ft. converter in easy handling and absolute control of the temperature. I think Mr. Howard is to be congratulated on the excellent showing he has made.

Jan 12, 1914

By B. D. Cullity

INTRODUCTION THIS investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy-the thermoelectric efficiency-has been discussed by Telkes1 in a recent review of the subject. She gives the thermoelectric efficiency as: [ ] For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of properties. BISMUTH-SELENIUM ALLOYS Work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson,2 who gives the diagram reproduced in Fig I. There are two intermediate phases in this system, BiSe and Bi2Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedral crystal

Jan 1, 1948

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By N. B. Pilling, R. E. Bedworth

The corrosion of metals is one problem on which time and thought have been expended for many years. In the effort to avert the destructive action of a hostile environment, attention has been directed almost entirely to the conditions under which most metallic structures are called upon to perform, and the extensive and complicated phenomena attending the corrosive action of atmospheric agencies, acting at the ordinary atmospheric temperatures, have been studied, but there is unanimity of opinion regarding many fundamental facts. One neglected phase is the corrosive action of various gases upon metals exposed to temperatures considerably higher than the atmospheric range, and more especially the attack of atmospheric oxygen upon exposed metallic surfaces. That the problem is difficult is connoted by the practical dominance of industrial electric heating by alloys of one type (nickel-chromium). Proprietary interest may account, in part, for the paucity of information available upon even the most general factors determining the behavior of metals and alloys when exposed to such exacting conditions. The present paper gives some conclusions reached as the result of experimental work, extending over several years, on the mechanism and contributory factors of the high-temperature oxidation of a number of simple unalloyed metals; it is free from experimental detail and proof. High-temperature metallic oxidation may be considered as a phase of metallic corrosion. The scheme outlined below, in which corrosive agent and environment are the principal criteria, is one way of analyzing the several groups of corrosion phenomena. Erosion.—Disintegrating or destructive action by physical causes. Corrosion.—Disintegrating or destructive action by chemical causes. Low-temperature Corrosion.—Solid participating phases essentially immobile: (a) Gaseous agent; (b) liquid agent: action electrolytic and action non-electrolytic. High-temperature Corrosion.—Solid participating phases possess diffusive mobility: (a) Liquid agent; (b) gaseous agent: reducing gases, oxidizing gases. (1) Water; (2) miscellaneous elemental and combined oxygen.

Jan 1, 1923

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By Zay Jeffries

IT is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a. fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a fine-grained steel rail might have grains or cells 100 times larger than coarse-grained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable than the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of. metal for a specific use, the latter determination being more indicative of. the life of the metal part than the tensile test. A grain-size determination with a tensile test is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now.

Jan 12, 1915

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939