Search Documents

By Thomas M. Drown

I DESIRE to communicate to the Institute the results of a few analyses which bear on the condition of carbon in gray and white iron. These analyses were made in the course of an investigation, now in progress, of the chemical composition of "chilling" irons. It will be remembered that Bell says he found no material difference in the amount and condition of carbon in gray and white pig iron made at the Clarence furnace, in England, and he therefore refers the difference in color and appearance in these two varieties of iron to the size of the particles of graphite. I quote from his "Chemical Phenomena of Iron Smelting:" "The inference I would draw from the information afforded by these analyses is, that the condition of iron in respect to its so-called `richness' is, within certain limits, entirely independent of its chemical constitution... . In the fluid state, I conceive the carbon, so taken up, confers upon the iron the property of fusion much below the temperature at which the pure metal melts, and the carbon itself may be regarded as dissolved in the iron. If, during the process of manufacture, the pig metal has been formed at a low temperature, consolidation, I imagine, takes place under such circumstances that the crystals are so minute, and the carbon which is separated assumes the uncombined or graphitic form in particles so minute as to be invisible, and, in consequence, the iron is white. If, on the other hand, the furnace is working at a very high temperature, the intensely heated iron crystallizes with large facets, upon which the extruded carbon assumes the condition of distinct plates or flakes. Should the temperature be less intense, these crystals are of smaller dimensions, and the separated carbon is less conspicuous, and, as the temperature of the furnace declines, the crystals decrease in size, as do the flakes of carbon, until both disappear in white iron. . . . Returning, then, to temperature as the cause of differences in quality of pig iron, the `chilling' of gray metal, and its conversion into white, may be regarded as the effect of preventing, by rapid cooling, the formation

Jan 1, 1875

By Carl Keuffel

THE manufacture of optical glass is a new industry in this country. In 1914, after the war started, the supply of optical glass from Europe was cut off, but as there was a fairly large stock of glass on hand, it was not until the end of 1915 that the optical instrument makers made serious efforts to produce their own glass. These early attempts were generally made by practical glass men and, due primarily to the fact that very little scientific help was used, the first attempts were unsuccessful. It was not until the whole problem was attacked by technically trained men who used advanced methods of research that good results were obtained. These researches proved that the accurate control of the temperature was a most important factor in the manufacture of optical glass. The early glass maker judged temperatures with his eyes; later, Seger cones were introduced into the furnace at various stages of the melt. Then radiation, indicating and recording pyrometers with rare-metal thermocouples were introduced. Now, in addition to these, an optical pyrometer every hour or so is sighted right into the pot and on the molten glass. Figs. 1 and 2 show how pyrometers are used to control the melt. InFig. 2, Y is the clay pot in which the batch is melted to glass within the furnace X. The rare-metal thermocouple S, protected by a clay tube, extends through the wall and about 4 in. into the furnace. This couple is connected to an indicator T and a recorder U so that a complete record of the furnace temperatures is obtained. The section of the curve ABCD, Fig. 1, shows how gradually and carefully the clay pot must be heated to get rid of moisture AB and during the calcining at CD. The stem of an expansion pyrometer R is extended through a hole in the door Z of the furnace and into the pot in order to more closely follow the temperatures of the clay pot itself during the burning process, that is from A to D. After the pot is calcined, the temperature can be rapidly raised to E (about 1430° C.); from E to F this temperature is much higher

Jan 9, 1919

By Enrique Touceda

As IN the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time. A few years ago, about the only test made to ascertain the physical properties of the product, t except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in, castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 2, 1920

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By Hanlu Xie, Liang Yu, Ping Wang, Yuanchi Dong

"The leaching process is the first step when recycling BF slag as raw material for some other products. While studying the kinetics of the BF slag leaching process, a fractal phenomenon was found, which indicated some interesting mechanism in the process. The result suggested a new understanding of the leaching process in detail which useful for the industrial applicationIntroductionTypical composition (wt. %) of blast furnace slag varied in a pretty wide range: SiO2 30–40, Al2O3 10–20, CaO 30–40, MgO 5–10.The ground granulated slag is commonly used as base of roadway (mixed with natural inert for paving, soil stabilization, etc.) or one of the resources of Portland cements because of its good hydraulic activity [1]. To recycle the slag economically, the selective recovery of some components of the slag may be considered. As main components exist in the slag, silica [2, 3 and 4] and alumina [4] recovery was first considered.While recovering of silica from the slag, silica gels are recovered selectively from the leaching solution deriving from the treatment of the slag with waste sulfuric acid. After separation of the exhausted solid of leaching, the silica gel is precipitated from the solution at pH 3.2. Although the silica gels obtained by this procedure contain many impurities and need some more work afterward, it is the first and important step for the process.In the prior work [5], silica extraction using blast furnace slag had been investigated, focused on the pH value of selectively silica extraction. In the present work, kinetics of the leaching process was focused. It is important to design an economical process.ExperimentalThe composition of the slag and the calcined gels has been determined by a LINK860 (Oxford Instruments, Oak Ridge, TN) energy dispersive spectrometer (EDS) in conjunction with a CAMBRIDGE S250-M2 (Cambridge Instrument Ltd., Cambridge, U.K.) scanning electron microscope(SEM). The leaching of slag and the precipitation of silica gels have been conducted at atmospheric pressure in a stirred reactor placed at temperature controlled by a heated water bath."

Jan 1, 2008

By F. Leclerc, V. Rebeyrolle, M. Revil-Baudard, A. Jardy, M. Založnik, H. Combeau

"Since the quality of Vacuum Arc Remelted ingots is linked to their chemical homogeneity and metallurgical structure, a modeling study of the solidification during VAR has been undertaken. It is based on the solution of the coupled transient heat, momentum and solute transport equations during the remelting of a cylindrical ingot. Solidification mechanisms implemented in the model include a full coupling between energy and solute transport in the mushy zone, and accounting for nucleation and finite diffusion of solutes at the microscopic scale, in both solid and liquid phases. This modeling can be applied to actual multi-component alloys. In this paper, the macrosegregation in Zircaloy 4 ingots is investigated. To validate the model, one single melt of a homogeneous electrode has been specifically performed. The comparison between the predicted macrosegregation and the experimental results shows the importance of accounting for solutal convection to forecast properly the macrosegregation in remelted ingots.IntroductionVacuum Arc Remelting of zirconium alloy ingots is a key step in the manufacturing process of fuel assembly components in nuclear reactors. The control of the chemical homogeneity is indeed fundamental to ensure the quality and the in-reactor performance of the final products. Despite the use of electromagnetic stirring to homogenize the liquid melt composition, chemical heterogeneities develop in the mushy zone during the solidification stage. One of the main challenges for zirconium producers, as well as titanium producers, is to master the VAR process in order to control the macrosegregation in remelted ingots. Macrosegregation results from the association of microsegregation and transport phenomena. The latter are primarily due to the flow in the liquid and mushy parts. It is now well established [1-4] that the hydrodynamics of the melt pool in a VAR ingot depends on the combined action of the followings: thermal and solutal buoyancy, self-induced electromagnetic force and the periodic centrifugal force caused by the angular movement generated by the stirring. However, for zirconium alloy ingots, the effects of thermal and solutal buoyancy forces on macrosegregation through their influence on the flow in the mushy zone have not been clearly identified."

Jan 1, 2012

By George Hallerman, R. J. Gray

In the customary method of studying age hardening, the process of aging is interrupted by cooling the specimen and measuring its room-temperature hardness. However, the aging process may be conveniently measured while it is occurring at an elevated temperature by a series of hardness measurements at suitable time intervals. The latter method gives data void of complications that might result from processes occurring during the quench, and the data may be more indicative of the alloy's properties at elevated temperatures. The elevated-temperature hardness tester1 used in the present study employed a dead-weight loading system with a synthetic sapphire Vickers-type in-denter mounted in a molybdenum holder. The tests were performed in a vacuum of l0 to 10 torr. Hardness impressions were made by applying a 2-kg load for 15 sec. Although the hardness impressions made in the tester at elevated temperatures were measured at room temperature, the correction for thermal contraction during cooling was insignificant and therefore neglected. The two methods of obtaining age-hardening data were compared using eighteen samples of Haynes alloy No. 25* which had been annealed for 2 hr at 2250°F (1232°C). The test surfaces of the 1 by 1 by 1/4-in. samples were ground and then polished on vibratory polishers2 prior to testing. Three groups of five samples were aged at 1400°, 1650°, and 1800°F (760°, 899", and 982°C) for 4, 16, 32, 64, and 100 hr and then water-quenched. Room-temperature hardness as a function of aging time for these samples is shown in the broken lines of Fig. 1. Only one sample for each of the three temperatures was necessary to determine the hardness of the alloy at the aging temperatures with the elevated hardness tester. The specimens were heated isothermally and hardness impressions were made after various time intervals up to 100 hr. The results of these determinations were represented by solid lines in Fig. 1. Comparison of the two sets of curves shows, as expected, the hardness values determined at the aging temperatures are lower than the room-temperature hardness of the quenched specimens and the hot-hardness values reflect a strong tempera-

Jan 1, 1964

By W. H. Adams

I DOUBT if many of our engineers know of the existence of coal-fields extending over hundreds of miles of territory bordering on and lying contiguous to the Rio Grande River in Mexico. Essential as these facts are to those contemplating the starting of industrial works along our frontier, I have not been able to learn that any surveys or examinations have been made of these deposits, and I trust the preliminary and unofficial investigations lately made by myself may be found of interest, especially to those of our members whose experience has been with poor fuel, or in districts remote from railway facilities. While it is true that Northern Mexico is generally bare of charcoal-making timber, yet no greater mistake can be made than to condemn the light, quick-growing woods found in profusion, and which cannot be excelled in flame or heat-producing qualities for boilers, reverberatory furnaces, or hearths. No country could be surer of a full supply of wood if wise legislation in regard to irrigation and preservation of young timber were adopted and enforced, but the beneficiation of the low-grade ores of Mexico demands a more dense fuel for furnace work, and, fortunately for metallurgists, who will hereafter make this frontier a base of operations, there have been disclosed, near the surface, seemingly inexhaustible beds of semi-anthracite and bituminous coals. No extensive openings have as yet been made, and my own workings at the Cedral mines are all that can yet be said to prove the quantity and quality of the coal, other openings furnishing only corroborative evidence. Our location (one hundred and ten miles west of the Rio Grande River) is on the western line of the depository basin, as it has existed since the period of activity along the volcanic line. The region farther inland I have not examined, but the elevations, as a rule, are much greater, though from the nature of the formation, they are not necessarily barren-ground. Beginning at the base of the Santa Rosa Mountains (location of the Cedral mines), we find very interesting breaks in the foot-hills, disclosing the stratified rocks from the volcanic centres to the valleys.

Jan 1, 1882

By S. W. Parr, T. E. Layng

The low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700" or 800" C. For convenience in this discussion, the single number 750" will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750") there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750") there is substantially no secondary decomposition; above 750") the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750". Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for- example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing . conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement of the evolved gases is lively and reduces, correspondingly, the time for the retention of the gases in the passageways where these milder decomposing conditions exist. It is acknowledged that the maintenance of these temperature conditions at the present time has only an ideal and not a practical status. Actual operations under these conditions, as a? industrial accomplish-

Jan 1, 1920

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By B. L. Dunic, Terkel Rosenqvist

rr has long been suspected that sulphur has a small but finite solid solubility in iron, but up to the present more accurate data have been lacking. The survey given by Hansen' illustrates the divergence of data and opinions. Solubilities between 0.01 and 1.5 pct have been suggested, and opinions vary regarding the effects of temperature and phase transformations in iron on the sulphur solubility. The extent of solid solution and its variation with temperature might be expected to be an important factor in the occurrence of hot shortness in steel. Therefore, the object of the present investigation was to study this problem more systematically. It was furthermore hoped that solubility data for sulphur might contribute to an understanding of the factors which determine solid solubilities in general. Experimental Procedure The present work was based on the measurement of the chemical activity of sulphur in the solid solution by means of equilibrium with a mixture of hydrogen and hydrogen sulphide. When the solid solubility limit is reached, the sulphur activity in the iron becomes equal to that in the coexisting sulphide phase. A gas mixture of a controlled H,S/H, ratio was passed over pure metallic iron heated to a temperature in the range 900" to 1500". The amount of sulphur absorbed by the iron was determined by analysis, and from a plot of percentage of sulphur vs. gas composition the sulphur activity and the solubility limit were determined. As the rate of diffusion of sulphur in solid iron is very small, often several days were needed to be sure that equilibrium conditions had been established. To produce a gas flow with less than 1 pct H,S of constant composition for several days, was in itself a problem. The most satisfactory arrangement was obtained by a continuous synthesis of hydrogen sulphide from the elements. This was done in the part of the apparatus shown to the left in Fig. 1. The hydrogen used was first purified in tank batches by passage through activated charcoal cooled in liquid nitrogen under a pressure of 150

Jan 1, 1953

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

The scheme of rehabilitation of surface plant commenced in 1936, included the provision of improved and more hygienic changing and bathing facilities for the employees.At that time the Thompson's Shaft section of the British Mine was being prepared for a resumption of operations, and it was decided to repair and re-equip the existing building. Thus any new scheme adopted could be given a thorough trial, and the proved arrangement used as a basis for the contemplated new main changehouse on the North Section.Investigations were carried out to determine the most suitable arrangement for the Thompson's Shaft changehouse, to provide for a total of 120 men, with particular regard to the internal fittings and fixtures. Also, as the mining conditions were such that a large proportion of clothes worn underground by miners, etc., were wet by the end of the shift, the problem of drying these clothes in the availaole time from a man coming off shift to his commencing again some sixteen hours later was one of the most important to be dealt with.The changehouses in use on the North mine section of the lease were provided with racks around the walls for the men to hang their street clothes on, and a section was partitioned off to house the mine clothes and their drying facilities. The actual drying was carried out by means of hanging the wet clothes over racks between which ran pipe coils heated by means of hot water circulated from the hot water boiler supplying the showers.This method had proved to be far from satisfactory for several reasons, the main objections being:-

Jan 1, 1940

By C. R. Hayward, H. O. Hofman

The aim of instruction in a metallurgical laboratory is to make real the principles on which metallurgical processes and operations are based, and to foster the spirit of investigation. The materials with which experiments are carried out are ores, metals, and metallic compounds. The method varies with the end sought. A class may work as a whole, each member contributing his share to the solution of a problem, or the students may carry on investigations independently; the former exemplifies class-research; the latter, individual research. It is with a branch of the former, with special reference to ore-treatment, that the present paper deals. In smelting an ore by a well-established process, the result is shown by analyzing the products to see whether their compositions correspond to those calculated in making up the charge; by taking account of stock to show the distribution of metal in the different products made and the losses from dust and volatilization; by casting a thermal balance to find the distribution and losses of heat; and by making a cost-sheet to ascertain, as far as possible, the necessary outlay of money. In lixiviation and amalgamation, the mode of operating has to be varied to adapt a process to the individual ore. Here a number of tests become necessary. Each will consist of a series of experiments with one variable, in order to find the conditions under which the variable gives the best result; a summary of several tests will give the best method of operating. Working a number of charges with the best method will furnish the data desired for ascertaining the recovery of metal,

Jan 1, 1910

By d&apos, Alton AJ, Rigden DT

Modern petroleum refining offers a complexity of environments, each requiring different metals for the satisfactory performance of-the various sections of the refinery, and this paper first outlines the varied enva.x¦on-ments thus met.It follows that the metal types in use will also vary to suit each particular environment, and the paper' consequently covers the use of ferrous-metals, ranging from plan carbon steels to the high alloy types and the non-ferrous metals, particularly copper and its alloys.The failures of some,of these metals and alloys are then illustrated by experiences it Kwinana. These failures are duo to (a) corrosion, (b) erosion, (c) faulty welding, and (d) mechanical defects,' of which the first is by far the most prevalent. The protective measures taken to prevent subsequent failures are then given under one or other of the following headings :(1) alterations in process conditions, (2) the use of alternative ,alloys,(3) suitable heat treatment, (4) redesign of the failed section, (5) cathodic protection, and (6) use of corrosion inhibitors.Reference is then made to the use of specialised metals and alloys.Metals, generally in the form of oxides or salts, are also used as catalysts in refining processes. Activated alumina is used, combined with silica .forScracking' of heavy oils, and as a support -for platinum, cobalt, molybdenum, nickel and similar metals, which catalyse hydro-genation and dehydrogenation-processes. .In the final formulation of petroleum products metallic compounds may be added. Reference is made to the large quantities of lead used by the petroleum industry and to the use of metallic soaps and detergents in the formulation of lubricating oils and greases.

Jan 1, 1962

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By Linli Wu, Guangchun Yao

"The influence of deformation on the properties of short-carbon-fiber reinforced 2024 alloy matrix composites was investigated in this study. It was found that the distribution of carbon fibers changed from the random state before deformation to the ordered state that carbon fibers arranged along the direction of rolling and extruding after deformation. Under the temperature range in control, the increase of rolling and extruding temperature would benefit to improve strength and elongation of composites, but was not conductive to improve the hardness of composites. With the increment of total deformation, all the strength and the hardness of composites became greater, nevertheless the elongation decreased. After being rolled and extruded, the strength and the hardness of composites were all bigger than those of composites before being rolled and extruded; moreover, the strength of extruded 2024 alloy matrix composites was higher than that of rolled 2024 alloy matrix composites under the same heat treatment conditions.IntroductionCarbon fibers have been reckoned as very important reinforcements due to the high specific strength, specific modulus, high thermal and electric conductivity, low expansion coefficient and good self-lubricant properties [1-4]. Light metal composites reinforced with carbon fibers, such as carbon fibers in an aluminum matrix, are widely used and studied. Some studies have concentrated on the interfacial characteristic of CF/Al composites in order to search for the way of improving the bonding between carbon fibers and the matrix alloy [5-8], and on the influence of the carbon fiber percent composition in the composites [9-11]. Some researchers began to take interest in the deforming characteristic and failure behavior of carbon fiber reinforced metal matrix composites [12-16]. However, the same with other metal materials, most of CF/AI composites were prepared by some single processes, such as powder metallurgy, extrusion casting and vacuum press infiltration, which caused that the composites products could not be manufactured directly. In order to cover the shortage of the mentioned above processes and get composites products with perfect mechanical properties and dimensional accuracy, the composites should be reworked by rolling, extruding or forging process. Compared with research about manufacturing process, the correlative investigation on the reworking of CF/Al composites was much less evidently, which restricted the application and the further development of CF/Al composites."

Jan 1, 2012

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

Book reviews Natural gas substitutes from coal and oil, by S.A. Qadar. Amsterdam, Elsevier Science Publishers, 1985. U.S.$83.25. Reviewer: U. Grimsehl High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metalurgy, 1985. 593 pp. £30. Reviewer: S.A. de Waal 2. Recent publications Uranium recovery from phosphates and phosphoric acid, by S. Huwyler. 3rd edition. Wirenlingen (Switzerland), Swiss Federal Institute of Reactor Research, EIR-Bericht (C) no. 1. Apr. 1985. 56 pp. Geological aspects of mining productivity. Canada's base metal resources, by B.W. MacKenzie. Kingston (Canada), Centre for Resource Studies, Queen's University, Technical Paper no. 6, Aug. 1985. 115 pp. $10.Taxation policies in the Canadian minerals industry, edited by M. Wojciechowski. Kingston (Canada), Centre for Resource Studies, Queen's University, 1985. Mineral policy update 1984: Policy and program changes afecting the Canadian mineral industry, by M.l. Wojciechowski and M.L. McAlister. Kingston (Canada), Centre for Resource Studies, Queen's University, 1985. $12. 3. Mintek reports Report MU7 The selective solvent extraction of pal/adium by the useof di-normal hexyl sulphide. Report M218 Modification of the design of screen boxes for carbonin-pulp and resin-in-pulp plants. Report M225 The commissioning, operation, and maintenance of an on-line corosion-monitoring station for the mining industry. Report M231The determination of selected lanthanoid elements by atomic-absorption spectroscopy using electrothermal atomization. Report M233 A computer programme for the prediction of hydrocyclone performance, parameters, and product size distributions. Report M234 The solvent extraction of base metals by mixtures of carboxylic acids and non-chelating oximes. 6 The efect of particle size and coloid stability on the wet high-intensity magnetic separation of uranium from cyanidation residues. Report M238 The beneficiation of fine coal. Report M240 The spectrophotometric determination of tin in silicates and tungsten-bearing materials. Report M242 Wear and performance of materials in pipelines for the hydraulic conveyance of fused ash. IPMI award for distinguished achievementThe International Precious Metals Institute has announced that Professor Henry C. Taube, Nobel Laureate, wil be the recipient of their 1986 Distinguished Achievement Award. Dr Taube is Professor of Chemistry at Stanford University, Palo Alto, California.

Jan 1, 1986

1. Book reviews Underwater tools, by Donald J. Hackman and Don W. Candy. Columbus (D.S.A.), Battelle Press, 1981. 152 pp. $32,95. Reviewer: B. Schmitz Uranium exploration case histories. Proceedings of Advisory Group Meeting Vienna, IAEA, 1981. Price: Austrian schillings 630. Reviewer: E. C. Kostlin Jet cutting technology, a review and bibliography, edited by Robin Brown. Published by BHRA Fluid Engineering, Cranfield, Bedford MK430AJ, England. Reviewer: D. O'Beirne 2. New Books Proceedings, Twelfth Congress of the Council of Mining and Metallurgical Institutions, by H. W. Glen (editor.) Johannesburg, The South African Institute of Mining and Metallurgy, 1982. 2 vols., 1060 pp. R78,85 (air-mail RI53,85). Amborite. Johannesburg, De Beers Industrial Diamond Division (P.O. Box 916), 1982. 6 pp. Free of charge. 3. New Journal BHRA Fluid Engineering has announced its new journal World Ports and Harbour Abstracts and the associated newsletter World Ports and Harbour News, which are issued from January 1983. The Abstracts is published bi-monthly and costs £60 in the V.K. and E.E.C., and £72 elsewhere. 4. Mintek reports Report 2134D On-line analysis, by X-ray diffraction, of fluorsparcontaining slurries. (First published 30th Sep., 1981.) Report 2135D A preliminary on-line analysis, by X-ray diffraction, of pyrite-containing slurries. (First published 30th Sep., 1981.) Report M28 The measurement of flow velocity distribution in fluids. Report M34 The determination, by atomic-absorption spectrophotometryusing electrothermal atomization, of platinum,palladium, rhodium, ruthenium, and iridium. Report M45 Two computer programmes for the calculation of massand heat balances in the production of high-carbon ferromanganese. Report M50 The development of an on-line gold analyser. Report M54 Major amounts of mercury in native gold from upper Witwatersrand sediments. Report M55 A new robust method for the treatment of analytical data. Report M57 The hydrometallurgical treatment of liquors generated by the leaching of a low-grade matte. Awards for inventions For inventing devices of exceptional value to the mining industry, two mining men were presented with awards in Johannesburg on 25th November, 1982, under the Chamber of Mines' Ideas and Suggestions Scheme. Mr W. W. Malan, President of the Chamber of Mines, made the presentations.

Jan 1, 1983