Search Documents

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956

By O. D. Sherby, J. E. Dorn, C. D. Wiseman

MCLEAN&apos; has shown that the total strain obtained during creep of aluminum polycrystals arises exclusively from the mechanisms of 1) microscopically observable slip, 2) subgrain tilting, and 3) grain boundary shearing. Extensive analyses, however, suggest that the high temperature creep of metal polycrystals is controlled by a single thermal activation process."" These somewhat contradictory observations might be reconciled if it could be shown that the activation energies are identical for each of the mechanisms isolated by McLean. Such identity of the activation energies, of course, would demand that the same unit process controls the functioning of each individual mechanism. Under these conditions the activation energies for creep of single metal crystals and polycrystalline aggregates and for grain boundary shearing should be identical. This paper is primarily concerned with the possible identity between the activation energies for high temperature creep of single crystal and polycrystalline metals. In addition, comparisons will also be made between the activation energies for creep of single crystals and polycrystals with previously reported activation energies for grain boundary shearing.0"8 Materials and Techniques The same high purity aluminum, lead, and tin were used in the creep tests for single crystals and polycrystalline aggregates. Single crystals of aluminum and tin were prepared by the strain-anneal technique, whereas lead single crystals were prepared by growth from the melt. The tensile creep stress was maintained constant by Chalmers-Andrade parabolic-type lever arms. Strains were measured to &0.0002 in. per in. with rack and pinion type extensometers, and temperatures were maintained to within & 0.2"C of the reported values by mercury-thermoregulated resistance-heated silicone oil baths. The previously reported unambiguous technique for determination of the activation energy for creep was employed throughout this investigation.&apos; ." It involves periodic abrupt small changes in temperature during the course of creep, accomplished by rapidly replacing one creep bath at temperature TI by a second bath at T,. The abrupt change in creep rate from i, to & attending the abrupt change in temperature is due exclusively to the change in temperature, since both the stress and the substructure are identical the instant before and the instant after a change of temperature. Therefore, all other factors being identical where AH is the activation energy for creep and R is the gas constant. Results Typical examples of the creep rate vs creep strain data during temperature cycled creep tests of single

Jan 1, 1958

By E. E. Donath

THE coal hydrogenation process is well known as a means for production of liquid fuels from coal. In this paper, the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid-phase and vapor-phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high-molecular-weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below 325ºC, for instance-can be influenced by temperature, residence time, and catalyst of the liquid-phase hydrogenation. In vapor-phase hydrogenation, a solid bed catalyst is used to convert the intermediate oil from the liquid-phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring-compound content of the liquid-phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparafhns.3 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid-phase stage, coal is made into a paste with re- cycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high-pressure converters where the liquefaction of coal, conversion of the high-boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470ºC. The reaction products enter the hot catchpot in which oil vapors of lower boiling point

Jan 1, 1953

By Daniel Kim, Michael Free, Justin McAllister, Urian Marshall, Shijie Wang

"Cathode impurity levels of electrorefined copper were evaluated based on 1/10* scale laboratory electrorefining tests. Cathodes were evaluated near the top, mid-section, and bottom sections of cathodes on both the set and mold sides and strip and scrap cycles. Slime weights were measured, and slime and electrolyte samples were also evaluated for impurities. Results from these tests have been compiled and compared to evaluate the effects of changes in operating conditions and electrode location on cathode impurities.IntroductionMany types of impurities are commonly found in commercial copper electrorefining anodes. The smelter operations that produce the anodes process concentrates that contain a wide variety of impurities that vary based on the mineralogy of the ore. Most anode impurities are removed during electrorefining. However, a portion of the anode impurities is incorporated into the copper cathode product. The mechanisms by which impurities are transported from the anode to the cathode are not well understood. Some impurities can be transported as anode slime particles to the cathode where they are incorporated into the cathode. Other impurities can be transported as dissolved species that are electrochemically reduced with the copper to become part of the cathode. Although research has been performed on anode slimes and impurities [1-4], there is a need for additional information regarding the relationships associated with electrorefining cycles, electrode faces, local electrode positions, anode impurities and specific cathode impurities. The objective of this study was to evaluate lead, arsenic, and antimony cathode impurity trends associated with electrorefining cycles, electrode faces, local electrode positions, and anode impurities. A variety of techniques including electrolyte filtering, anode heat treatment, high electrolyte arsenic concentration, high arsenic and/or lead in anodes, flocculation of slime particles, and appropriate current density control were used to vary cathode impurity levels. Each test was performed only once for a strip cycle and once for a scrap cycle. Consequently, the results for the individual conditions are preliminary and are not the focus of this study. However, the collective set of data with varying impurity modifying techniques provides a broad range of impurity levels, and the associated trends with respect to lead, arsenic, and antimony are discussed in this paper. Approximately 180 analyses of copper cathode were used to track the antimony, arsenic, and lead impurities. Eighteen anode slime samples were also analyzed for antimony, arsenic, and lead."

Jan 1, 2012

By W. L. Chu

It was observed that chromized coatings on low carbon steel could be embrittled by cooling slowly through the 475°C range. A higher chromium coating was more susceptible to embrittlement than a lower chromium coating. Coating structure and composition could be correlated with the chromizing process and prior carbon content of the steel. IT was recently observed that during the fabrication of rectangular tubings made with chromized thin gage 1010 steel, a high percentage of these parts were fractured readily in a brittle manner under the light impact-forming load employed. Ensuing investigation indicated the cause for such brittle failures to be the so-called 475°C embrittlement of the chromized coatings. The experimental work and results are briefly reported. Rectangular tube sections of normalized AISI C1010 steel, which had a cross-section of 0.5x1.5 in. and a wall thickness of 0.030 in., were chromized to yield coatings having several ranges of thickness, varying from 0.0005 to 0.002 in. Essentially, the chromizing process is similar to that described by Samuel and Lockington,&apos; which consists of heating the parts in a sealed container at about 955°C for 4 hr in intimate contact with a chromizing mixture* samples in a hydraulic press, and the other employed a simple beam bending test of the flat sides of the tubing walls. Neither, however, was able to differentiate the relative brittleness of samples known to include both the brittle and tough types, since the impact-brittle samples were found to deform readily in a manner similar to the tough ones. Both the tough and brittle samples were studied by reflection microscopy. Observation showed that the microstructures of the steel cores were similar in content and distribution of inclusions as well as in the ferritic grain size. Results of Filar micrometer measurements showed that coating thicknesses+ of the brittle samples averaged 0.0007 in., whereas those of the tough samples averaged 0.0016 in. The micrographs of Fig. 2 illustrate the structural differences between coatings of both types of samples. By dissolving the steel cores in nitric acid, coatings of both the brittle and tough samples were isolated. Simple bending tests showed that coatings of the brittle samples cracked readily at about 90" bend, whereas those of the tough samples could be bent nearly 180° without cracking. The coatings as well as the steel cores were analyzed for carbon and

Jan 1, 1956

By Wilhelm Flesch

THE object of development work in the field of gasification is to find a process by which all&apos; fuels, regardless of their individual properties, can be gasified economically. This paper describes the development of the Winkler process. The economy of the gasification process depends not only on the degree of the gasification effect but also, to a decisive extent, on the costs of fuel, production, and installations. Fig 1 shows the relation between fuel costs and gasification efficiency for various types of fuels. Since the fuel cost in the gasification of coke amounts to two thirds of the price of gas, and the thermal unit in brown coal costs only one third of what it costs in coke, it is easily seen how profitably cheap fuels can be gasified, especially if these fuels require minimum preparation and gasification is done in the vicinity of the mines. These possibilities were a great advantage of the Winkler generators, which were installed 20 years ago in the central German brown-coal fields and, at that time, were without rival for the gasification of finely divided fuels. In the Winkler generator (Fig 2), crushed and ground solid fuels were, for the first time, successfully gasified with oxygen and steam on an industrial scale. Unlike the usual processes formerly employed on an industrial scale, this gasification, which proceeds continuously in the glowing, seething fuel bed, makes only extremely low demands on the fuel. The fuel no longer has to be in lumps and abrasion-resistant, but must be capable of reaction and must be fed into the generator in a grain size of 0 to 8 mm. Brown coal or bituminous coal, or their low-temperature cokes, can be gasified in the Winkler generator. Large plants using fuels are operating on an industrial scale in Europe and in Japan. Table 1 shows the results obtained by gasifying these, fuels in Winkler generators. The thermal efficiency of gasification, which is the relation between the calorific value obtained in the gas produced and that of the fuel consumed, gives no indication of the quantity of steam generated in gasification. The generation of steam in the waste-heat boiler of the Winkler generator adequately-covers the steam consumed in gasification. To obtain effective gasification in the Winkler process, combustible mate-

Jan 1, 1953

By R. P. Heuer

In recent years an increasing amount of research work has been done on refractory materials for use in copper-smelting furnaces. A few of the larger refractories manufacturers have erected special research laboratories which are fully equipped to study the refractory problems of the smelter. A typical laboratory of this type was described in the January, 1929, issue of Mining and Metallurgy, in an article entitled "Methods of Research Newly Applied to Refractories," by W. F. Boericke. This particular laboratory is equipped for the manufacture of full-size refractory brick. It aims to study on a fairly large scale the behavior of various refractory raw materials and the effect of improved methods of manufacture. The refractories manufacturer has at his disposal the naturally occurring refractory oxides in various degrees of purity, mixed or combined with other oxides. In order to supply the copper smelter with a refractory brick that will permit the most economical operation of the smelting furnaces, it is necessary to have the optimum combination of a number of both physical and chemical properties in the brick. Unfortunately, nature has not provided any raw materials in which the perfect combination of these properties exists. It is, therefore, a problem for man&apos;s ingenuity to seek out the most desirable raw materials and develop methods of manufacture that give, in the resultant product, the necessary combination of properties in as full a measure as is possible. In the laboratory it is possible to carry out fairly broad experiments with this objective. It is first necessary to obtain and process the raw materials, then to manufacture them into brick and finally, to test these bricks under conditions designed to interpret or simulate in the laboratory the actual conditions in the smelting furnace. It is necessary for the research engineers to determine certain fundamental properties in the brick which may be subjected to laboratory measurements and to interpret these measurements in terms of brick performance in smelting-plant practice. Such procedure is not what might be called an exact, scientific one but it has been found that great progress can be made when these principles are applied. For example, the resistance of refractory brick to spalling and thermal change can be related to the thermal expansion of the refractory, its thermal conductivity and heat capacity and its

Jan 1, 1934

By E. S. Greiner

Germanium and silicon have been plastically deformed in torsion at elevated temperatures. Slip took place on the four {Ill} planes. Dislocations, revealed by etch pits on a (111) face, occurred in rows that were traces of operative slip planes. THE plastic deformation of germanium and silicon by bending and tension at elevated temperatures has been reported by Gallagher.&apos; Transla-tional slip during plastic flow in these materials, according to Gallagher&apos; and Treuting,&apos; occurs on (111) planes. Recent work by Treuting&apos; indicates the direction of slip to be <1l0>. The present paper describes the plastic flow characteristics of germanium and silicon deformed by torsion. Torsional deformation was accomplished by twisting 1/4x1/4x2 in. specimens held in molybdenum grips and contained in an atmosphere of helium in a transparent quartz tube and heated by an external resistance furnace. The angular displacements were measured on a graduated circle with a pointer attached to the movable grip. Temperatures were measured with a chromel-alumel couple; the hot junction was within the quartz tube and in close proximity to the specimen. Photographs of samples of germanium and silicon twisted at 850" and 1180°C, respectively, are shown in Fig. 1. The germanium was twisted 230" per in. and the silicon 80" per in. These deformations are larger than those used in experiments to be described later and are presented only to emphasize the extensive plasticity of these materials. Germanium A single crystal specimen of germanium (n-type, 7 ohm-cm resistivity) with a (111) plane normal within 3" of the torsion axis, Fig. 2, was chemically polished with CP-4 solution" and then twisted 9" during the twisting of these specimens of germanium, the slip lines from the (lli) plane should have appeared in the four lateral faces instead of in only two. Perhaps the absence of rotational slip is brought about by the square cross-section. A cylindrical specimen would have a more uniform stress distribution in torsion than one with a square cross-section, and may deform by rotational slip. A specimen of germanium (n-type, 5 ohm-cm resistivity) twisted less than 8" per in. at 550°C, was cut to expose the (111) face 19" 28&apos; from the torsion axis, Fig. 4a. This face, after metallographic

Jan 1, 1956

I BELIEVE that my work would surely be host a seed without fit and that I would fail in that cause which disposed me to satisfy your request to write and form this work [75] if while laboring on it I did not tell you of the art of casting, since it is a necessary means to very many ends. I realize even more that I must tell as much as seems necessary since I have already demonstrated the methods of recognizing the natures and locations of the metals, of smelting and reducing them to their ultimate perfection, and finally have taught you to make their associations and alloys. It is especially necessary since this art and work is not well known, so that no one can practice it who is not, so to speak, born to it, or who does not have much talent and good judgment. For this reason and also because it is closely related to sculpture, whose arms are the support of its life, it is very highly esteemed. In order to describe the whole art in every part, I say that the greatest labors of both mind and body are required for its operations in the beginning, middle, and end. It is indeed true that these labors are endured with pleasure because they are associated with a certain expectation of novelty, produced by the greatness of art and awaited with desire, particularly since the artificer sees that it is an art pleasing and delightful even to ignorant men. As a result, as if ensnared, he is often unable to leave the place of work. To conclude: The outcome of this art is dependent upon and subject to many operations which, if they are not all carried out with great care and diligence and well observed throughout, convert the whole into nothing, and the result becomes like its name [cast away]. Therefore, having considered this work many times, with its extraordinary obstacles and the bodily labors heavy as a stevedore&apos;s, instead of exalting it with praise, I wish to say that it is such that a man of noble birth, even though he be gifted or be drawn to it by pleasure, should not practice it and could not unless he is accustomed to the sweat and many discomforts which it brings. He must suffer the great natural heats of summer as well as those excessive and continuous ones from the enormous

Jan 1, 1942

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,&apos; and Hess and Cieorge.&apos; Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on &apos;Microcloth&apos; using a lubricant of &apos;Hyprez&apos; oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the &apos;Microcloth&apos; nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then &apos;whipped&apos; to a smooth consistency with 100-ml &apos;Hyprez&apos; oil. Before polishing, the diamond loaded &apos;Microcloth&apos; is moistened with a few drops of &apos;Hyprez&apos; oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By Floyd C. Kelly

There is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensataion of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is little gained by using specially purified gas, because it becomes contaminated after reaching the furnace. Low-carbon Steel If a sheet of low-carbon steel is annealed in such a furnace at 750" C. and allowed to cool with the furnace, an adequate flow of purified hydrogen being maintained all of the time, the steel will come out with a very thin coating of blue oxide. If a similar sheet is annealed at the same temperature and quickly pushed into the cooling chamber, it will come out nearly bright, or perhaps with only the edges slightly discolored. It is difficult to get a piece of steel through a furnace of this type with an absolutely bright surface. This is due to the fact that there are always traces of oxygen or water vapor in the furnace. When the steel is allowed to cool with the furnace, it reaches a critical temperature where the affinity of iron for oxygen is greater than that of hydrogen for oxygen, and the steel comes out discolored. If the steel is pushed from the hot zone

Jan 1, 1931

By Anne Kvithyld

Silicon solar cells, that convert the energy of sunlight into electric energy, are attractive sources of energy. In the production line wafers of solar cells are sliced from a multicrystaline ingot solidified unidirectionally. Recycling scrap from top and sides of such ingots is addressed. SiC and Si3N4 inclusions are a major problem. Scrap from Scan Wafer ASA is melted in a high vacuum furnace at around 1500ºC. The filters, from commercial producers, are C and SiC with 10, 20 and 30 ppi. Characterisation of inclusions before and after filtration, and in the filter itself, is performed by microscopy. Dissolution of silicon in acid and counting of the un-dissolved inclusions is also carried out. In the filter Si3N4 needles and SiC inclusions were identified. The amount of these inclusions in the filtered silicon is much less than in the input. In conclusion, filtration using SiC and C filters in vacuum system in argon atmosphere removes SiC and Si3N4 inclusions from solar cell scrap. Flow of metal through the filters is not a problem. These results are promising with scale-up to industrial application in mind.

Jan 1, 2006

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By Charles A. Mitke

Discussion of the paper by CHARLES A. MITKE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1941 to 1958. GERALD SHERMAN, Bisbee, Ariz.-Mr. Mitke justly might have made much stronger his claim for increase in efficiency of labor due to the introduction of forced ventilation. The product per man shift in stoping in the Gardner division has practically doubled. While it is true that improved methods have been responsible for a great part of this gain, and what is due to better ventilation cannot be definitely known, yet it is also true that the results could not have been obtained in that division as it was in 1912. . The paper discusses the two systems of ventilation in use, exhaust and pressure. In both the object is the same, to take foul air or gas out of the mine by the most direct course and replace it by fresh. In coal mines, the exhaust system is in almost universal use, and since the most advanced work in ventilation has been in that class of mines, it was naturally the first one to be considered. It has the advantage of leaving all adits, shafts, or other openings free for use. Doors are only needed to direct the course of the air, and not to confine it. Its disadvantages appear in case of fire, or if the ground over the mine is much broken by subsidence. The fan must work in gas in the case of a -fire, and may be. damaged or destroyed either by heat or by corrosive gas. At the time of the fire in the Lowell division of the Copper Queen, a small exhaust fan was placed over a ventilating raise, but the vanes and housing were destroyed by sulphurous gases within a few weeks. If the ground above the mined area is much broken, as is frequently the case when the ore deposit is thick vertically, a good deal of air is likely to pass through it, particularly if it is near the surface. Leakage from this source is a loss to the exhaust system by short circuiting, which is exaggerated by a contraction or block in the air course. It serves as an added outlet in the pressure system. This is strikingly shown at the United Verde, where many jets of steam may be seen coming up through the ground above the stoped country on a cold day.

Jan 12, 1915

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite&apos;s use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. &apos;C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. &apos;M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. &apos;E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. &apos;W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. &apos;H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By A. U. Seybolt

RECENTLY, cases of coexisting ordered and disordered phase equilibria have been reported among face-centered cubic metals,1"3 but not on body-centered cubic systems.4 McQueen and Kuczynski5 showed a single line as the boundary between ordered solid solution of Fe3Al type and corresponding disordered solution in the Fe-A1 phase diagram based mainly on dilatometric and magnetic measurements. Such a single line would indicate a second or higher order transition. or an absence of coexisting order and disorder. The writer found previously a two-phase equilibrium region at 800°C consisting of ordered and disordered solid solutions of Fe3Si in a matrix of approximately 1-6 wt pct Si (Fe3Si is of 14.3 wt pct Si). A similar two-phase region of ordered and disordered Fe3Al solid solutions might be expected if the similarity between Fe3Si and Fe3Si structures hold true. In the present investigation, a wire of 22 at. pct Al, balance Fe and 0.0513 cm in diameter was subjected to electrical resistivity measurement in vacuum as a function of temperature between 300 and 800°C, see Fig. 1. There was excellent agreement between data taken on heating and on cooling: no hysteresis was observed. The Curie temperature was determined to be 640 °C which agrees with the finding by McQueen and Kuczynski.5 But in addition, there were two transitional points in the resistance-temperature plot at 510oC and 400 "C. The former is thought to be a connection with the transition from disordered state to a coexisting order and disordered equilibrium state; while the latter, from such coexisting state to ordered state. Fig. 2 shows a phase diagram where the suggested two-phase region lies between dotted lines. The solid lines are those of McQueen and Kuczynski.5 Since these authors found only a single-phase boundary between ordered and disordered Fe3 Al, it would seem likely that the dilatometric method used by these authors was not sufficiently sensitive to resolve the ordering reaction into the two-phase boundaries. In addition, their phase diagram conflicts with the statement they make on P. 1 of their paper: "The sharpness of the peaks indicates that ordering to Fe3A1 is a first order reaction." The suggestion of coexisting order plus disorder in Fe3A1 must be considered tentative until confirmed by high-temperature X-ray examination. If

Jan 1, 1961

By Wang Ding-heng, Wang Zhi-yuan, Nolan B. Aughenbaugh

The People&apos;s Republic of China has abundant coal resources with proven reserves amounting to 582 Gt (641 billion st). Recognizing coal as a major energy source on which to build the country&apos;s industrial and economic base, there has been a rapid increase in production since the founding of the People&apos;s Republic. In 1949, only 29.4 Mt (32.4 million st) of coal was mined. Production has increased to 576.5 Mt (635.5 million st), exclusive of Taiwan, at present, making China the third largest coal producing country in the world. Plans call for a 4-5% increase in annual production for the next 20 years. Coal constitutes 70% of the primary energy consumption in China. The remaining 30% is divided between petroleum and natural gas with 26% and hydropower with 4%. Coal use and consumption is divided as follows. General industrial use comprised 48.9%, power generation uses 20.1%, and coking accounts for 10.5% (6.3% for metallurgy and 4.2% for chemical industry). Domestic use such as home heating and cooking makes up 17.8% and coal-fired steam engines for railways uses 4.7%. Coal Districts Coal underlies about 1/18 of China&apos;s land area. It occurs in 30 provinces, autonomous regions, and municipalities. In addition, the western interior region, which has not been explored, may contain sizable reserves. Based on geology, geography, and administration, the coal fields can be grouped into five districts as shown in Fig. 1. The north China district, the heart of the industrial base for the country, has the most extensive and largest deposits of the five districts. This amounts to almost 40% of the country&apos;s total reserves. The largest coal basin with proven reserves of 181.4 Gt (200 billion st) and the most exploitable seams is located some 300 km (186 miles) southwest of Beijing (Peking) in Shanxi Province. Centered around Taiyuan, the compound field extends from Datong in the north to Xian in the south. Its western extension is not known fully. The Northwest and Northeast districts contain the second and third largest deposits. The biggest coal field in South China is located in the Sichuan and Guizhou Provinces near Chongqing. At present, it is not known if sizable coal measures exist in the Tibetan district. Coal Types China&apos;s coal varies widely both in age and rank. Geologically, coal measures were deposited from the lower Carboniferous (Pennsylvanian of the US) and Permian of late Paleozoic, mainly during the Jurassic of the Mesozoic and peri¬odically throughout the Cenozoic. Collectively, coal from the lower Carboniferous, Permian, and Ju-

Jan 3, 1983

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

HAVING previously described the metals to you, before I proceed any farther I do not wish to fail to tell you, as I promised to do in the first chapter on metals, what I have learned through experience concerning the semiminerals, although this may seem to you outside our proposed subject. Since these are not produced by Nature as all rock or all metal they are called semiminerals by speculative physicians. Many kinds of these are found; those that resemble rocks are earthy, very difficult to liquefy, and much more adapted for adorning paintings than for anything else. Those that liquefy with fire, like sulphur, antimony, marcasite, [22] calamine, zaffre, manganese, and others, resemble the metals almost like brothers. Some others are more watery so that they dissolve in water, although they are fairly dense, and are obtained and reduced to their, perfection by means of water. These are the salts, vitriol, rock alum, and saltpeter. To these, as a watery thing, belongs also quicksilver, as it is commonly called because of its motion. Although it appears. not only liquid, but very liquid, this is not at all similar in its effects to any of the above. Indeed, it retains its same being until its very form is consumed. Since the reasons for its effects are almost impossible to investigate, I do not intend to speak of them here or to enter now this maze of speculation, because I wish to make definitely clear to you what this quicksilver really is. Therefore, leaving aside opinions and disputes, I shall take only those of the said semiminerals that I know are useful. First we shall see the method by which the semiminerals can be found and then how they are to be extracted from their matrices. These, perhaps, have no less need of effort and industry than the metals since they are substances completely hidden in the rocks or in the earth. For this reason some of these that are sought are made use of by means of fusion after they have been mined from their mother mountains, and some others need to be disposed by a certain maturative corruption, now with moisture and coldness, now with dryness and heat, as with waters, rains, frosts, or long baking in the sun, with fire, or even with a strong reheating within themselves. Most of them can finally be brought to the desired end by means of solution with water and fire.

Jan 1, 1942