Search Documents

By S. W. Zehr, G. S. Murty, W. A. Backofen

AN observation by Squires, Weiner, and phillipsl has stimulated interest in a mechanism of deformation at high temperature (above -0.5 of the absolute melting point) that is not usually thought to be involved in the creep of metals. They found precipitate-free or "denuded" zones along grain boundaries normal to the stress axis in tensile specimens of a hydrided Mg-1/2 wt pct Zr alloy after slow straining at 450° and 500°C. Their suggestion that the zones were a result of directional diffusion of magnesium atoms was supported with calculations from Harris and Jones2 which also tended to identify the process as Nabarro-Herring (N-H) creep3,4—a process that is characterized by Newtonian viscosity, with stress (o) directly proportional to strain rate (C), and one that proceeds by lattice diffusion. Material transport by diffusion along grain boundaries is an alternative basis for Newtonian viscosity, as demonstrated by Coble,5 and is favored over N-H creep for fine grain size and lower temperature.6 In either case, the strain rate sensitivity of flow stress, defined as m = d log o/d log E (which commonly appears in the empirical a = KEW), is unity. The experiments to be described here gave metallo-graphic indications of diffusional creep which were no less clear than those just cited, but the associated m (as measured by the method of Ref. 7) was much more like that of a Bingham material. For true Bingham behavior, (a — ao) E, where oo is an initial yield stress. Therefore, even if flow after yielding should occur by diffusional transport, m must increase from 0 as < is raised to reach unity only in the limit as One result is that the resistance to tensile necking conferred by Newtonian viscosity is lost, which would become increasingly apparent through the formation of more sharply defined necks as 6 is lowered. That trend appeared in these experiments. Most of the work was done on an extremely finegrained alloy of magnesium with -6 wt pct Zn and ½ wt pct Zr (Mg ZK60); the initial mean-intercept grain diameter, L, was 0.55 µ. Shown in Fig. l(a) is a germanium-shadowed carbon replica of the surface of a specimen that was coated with silicone oil,* heated to 270°C under a helium atmosphere, and then stretched locally -200 pct at an initial E = 3.3 x 10-5 sec-1. Under

Jan 1, 1969

By Samuel Doak

THE utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores, for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust, as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder, from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 1 ½ per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In

Jan 9, 1915

By David Reger

LITTLE new oil was found in West Virginia, during 1923, but there were important discoveries of gas. Most of the large oil producers have contented themselves with pumping old wells or in drilling only enough new wells in defined territory to maintain a fairly constant production, the attitude being that no, profit is made in producing high-grade oil at a low price and that an eventual loss is sustained by draining the reserves of a limited commodity that, at some more favorable time, will be of much value. The representative of one large company said: "We have done nothing but pump old wells during 1923 and we have made no plans for 1924." Careful attention to producing wells has been the rule, there having been few abandonments; the belief is prevalent that small wells will eventually become profitable under more favorable marketing conditions. In natural gas, the opposite point of view prevails. Because of the vast capabilities of the state for producing gas, its output being ahead of all others, great systems of transportation and distribution into the markets of four adjoining states have been built and a demand has been created that no present, or apparently potential, production can satisfy. This demand has become so great that large distributing companies not only discourage new applications for service but advise old customers to install coal furnaces for auxiliary fuel; some have requested public-service commissions to grant higher &apos;rates against large industrial consumers than those allowed for domestic heating. The response to this known market has been a rapid increase in price, both at the well mouth and at the door of the ultimate consumer, and the industry has become so stable that the only uncertainty, or hazard, appears to be the question of the presence of gas in fair quantity in a given territory under consideration. Several oil companies have now forsaken their policy of selling gas, wells outright when drilled and ;have organized gas departments to drill for gas and to dispose of the daily output by meter to distributing corporations. With such companies and with other producers whose interest is chiefly gas, the year has been busy and profitable. Some new territory of apparently large value has been proved and deeper producing sands in old fields have been tapped.

Jan 3, 1924

By E. T. Knight, John D. Gill

Much has been written and said concerning the alleged wasteful and uneconomic use of natural gas and petroleum. Espccially condemned has been the use of natural gas for the production of carbon black and the use of heavy fuel oil under steam boilers.&apos; The critics of these usages of gas and oil have sought to make effective their verbal attacks on the industry by the repetitive expression of the words "inferior" and "superior" uses2 of petroleum. Thus, to employ natural gas for residential heating was to use it in a superior way; to use it for the production of carbon black was to use it in a wasteful and uneconomic way. To use petroleum for the production of automotive fuel was to use it in a superior way; to employ it as a residential fuel and as the prime source of power in an industrial plant was to use it in an inferior and uneconomic way. No doubt the objections to such employment of gaseous and liquid natural hydrocarbons originated in the belief that natural gas and petroleum are limited, nonregenerative mineral resources, and that the functions they perform can be just as well performed by other natural resources like coal13 of which practically unlimited reserves are known. The generations that have dominated each of the last four decades have counted reserves4 of petroleum in terms of a few years supply. Meanwhile, domestic demand for motor fuel rose spectacularly from a few million barrels in 1900 to more than 500,000,000 bbl. last year.5 The more imaginative and vocal critics drew startling word pictures of the catastrophe of 25,000,000 motor vehicles made useless and of the great automotive manufacturing and allied industries brought to an untimely end, and millions of workers left hopelessly unemployed by what they called the deplorably rapid depletion of the petroleum reserve. Many of the critics have been sincere advocates of the conservation of natural resources; many others, and in recent years probably the majority, have espoused the doctrine of conservation to promote their own self-interest rather than that of the public. The latest advocate of severe restriction in the use of petroleum for the alleged purpose of conserving the petroleum resource proposes to achieve that end by a bill,6 now before

Jan 1, 1938

By T. J. Woodside

Prior to 1927 the lead blast furnace charge at El Paso consisted principally of direct-smelting carbonate ores, very low in zinc, and the resulting slag seldom carried more than 4.0 pct. With the exhaustion of the mines in Northern Mexico which supplied these ores, they were supplanted with a much smaller tonnage of sulphide concentrates containing appreciable amounts of zinc, and the zinc content of the slag rose to 10.0 pct. The Anaconda Company&apos;s slag fuming plant at East Helena, Montana, had then been in successful operation for several years, and it was immediately recognized that, while at that time the production of high zinc slag was small, if the grade held, a plant for the recovery of zinc from the accumulated slag might some day be practical. The grade not only held but became increasingly higher so that by 1946 suffcient slag had been accumulated to warrant the construction of a fuming plant regardless of future slag production from the blast furnaces, and with the removal of Government restrictions on construction at the end of the war the project was undertaken. The general design of the plant follows that at Bunker Hill, with waste heat boiler, unit coal pulverizers and even more extensive instrumentation and automatic control. The area around the lead blast furnaces is rather congested, being cut off from the nearest feasible site for the fuming plant by the copper plant, so that the most practical route for hot slag transfer is through the converter aisle. For this reason and also to make use of the existing converter cranes to serve the fuming furnace, an unused reverberatory at the north end of the converter building was dismantled and the fuming furnace and boiler located in its place. A flue at right angles to the furnace and boiler runs northward to the U-tube coolers and baghouse (Fig 1). From the bag-house a steel flue runs eastward to an existing and long unused 300 ft con- Crete stack. The coal handling system and de-leading plant lie north of the furnace and east of the cooling tubes and baghouse. The furnace is conventional, 8 X 21 X 33 ft high inside and completely water jacketed (Fig 2). There are 21

Jan 1, 1950

By Jerome Alexander

It is an outstanding fact of Nature that many of the practical properties of substances are dependent, not on their ultimate chemical composition, but on the kind and degree of aggregation of their constituent particles. Thus, a granite boulder is unmoved by wind or water, but if reduced to a fine dust it will be blown about by the wind and washed away by the rain. Carbon in one crystalline state of aggregation (diamond) is the hardest known substance, whereas in another crystalline state (graphite) it is so soft that it is used as a lubricant. Laying too much stress on the mere chemical analysis of substances is apt to obscure the fact that the nature of the aggregation of their particles is always a factor of importance, and sometimes the most important factor. Colloid chemistry deals with matter in a very fine state of subdivision; its sphere begins with particles just a little smaller than a wave length of light and extends down until they blend into molecular dimensions. With particles of this size, such phenomena as surface tension and adsorption, which depend on the development of free surface, become enormously magnified. Thus a cube of 1 cm. edge has a surface of only 6 sq. cm.; but if it is reduced to colloidal dimensions by being cut up into cubes each having an edge of 0.01 µ (0.00003 mm.), it will yield one million, million, million (1,000,000,000,000,000,O~) such cubes, having a combined area of 600 sq. m., or 21,274 sq. ft. The tiny force with which a drop of rain clings to the window pane becomes a factor to be reckoned with, if the surface involved is increased millions of times. From the colloid-chemical viewpoint, metals and alloys may be regarded as jellies or sponge-like structures,. the viscosity or stiffness of which at ordinary temperatures is exceedingly great; and like all jellies their properties are dependent on the composition and degree of dispersion of their constituent phases. These, in turn, depend on chemical composition, mutual solubility, speed of chilling, subsequent mechanical and heat treatment, etc. In fact, in preparing metals and alloys for practical use, we remove undesirable constituents (as in the conversion of pig iron into steel), add desirable constituents (as in

Jan 1, 1919

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6&apos;7 grain boundaries and possibly twinning planes.8&apos;9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5&apos;6&apos;9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By August Wendel

weight, and deflection, and recommends that the Pennsylvania Railroad Company denland that rails be made on specifications, based on these six variables, so narrow, that to fill them would cause the constant rejection of enormous quantities of steel, and a consequent enhancement of the price of rails, probably ten or twenty per cent., without any certainty that such rails would be any better than those the steel-mills are now making. I earnestly hope that the investigation which Dr. Dudley has so ably carried on will be continued. I hope the Pennsylvarlia Sailroad Company, or preferably a combination of several railroads, will institute the prolonged investigation which I think will be necessary to solve this deep problem; that they will take a hundred or more rails, watching and noting down carefully every detail of their manufacture as well as their analysis; that they will be carefully weighed before, during, and after service; that their crop-ends will be tested before service, and the rails themselves after removal; that all the sources of error which Dr. Dudley admits in the present investigation may be removed, and that enough facts may be gathered and tabulated so that the conclusions which may be drawn from them may be apparent to every one without labored discussion or heated argument. But I venture to prophesy that after this investigation shall have been completed, and a formula adopted which shall be satiefactory to both manufacturers and consumcrs, that formula will not be the one now under discussion. I hope Dr. Durlley will pardon me if I have been unduly severe in my criticism, and consider that I have written my remarks hastily and at a time which should have been given to needed rest. I differ with him only as regards the conclusions which he has drawn. I appreciate the value of his labors, and only make public my own conclusions in the hope of contributing to the advancement of the science of steelmaking, in which we are ail so deeply interested. Dr. August WENDEL, Troy, K. Y.: Dr. Dudley&apos;s last paper gives, certainly, very valuable and interesting information regarding the wear of rails under different conditions. His results concernillg the composition of rails, explotle, rather startlingly, some old theories regarding the wear of rails, and 1 think after his formula is silnplified it will be one good formula to work by. As he now arrives at the same conclusions reached ill his first paper, some of my remarks will apply to both, althougl~ I would

Jan 1, 1881

GEORGE F. COMSTOCK (author&apos;s reply to discussion*).-Mr. Thum&apos;s description of the effects of butt welding and spot welding on the micro-structure of steel are interesting and timely. The speed with which the changes noted by Mr. Thum must take place is indeed remarkable, but the writer has noted a similar very rapid diffusion of carbide in annealing a t a rather high temperature certain samples of soft sheet steel containing massive cementite segregated on a small scale. The massive cementite in such steel can be dissolved and distributed very quickly if the proper temperature is attained. Mr. Thum&apos;s explanation of the structure he found in the spot welds seems entirely reasonable, but the mystery of the decarburized material in the butt weld is one that might well be the subject of further research. The possibility of decarburization by air ,might perhaps be worthy of a little more consideration than he gives it, for the oxides formed would be gaseous on account of the presence of carbon, and hence not visible in the microscope, and the effect of the pressure might be to squeeze the carbon oxides, which would normally form blow-holes, out of the metal or possibly into such small volumes as not to be noticed The removal of carbon by liquation and squeezing into the fin would be an effect similar to the "bleeding" of a steel ingot that is rolled while the center is still liquid, giving a soft low-carbon interior in the finished section while the segregate was removed in cropping the pipe. This effect in Mr. Thum&apos;s butt welds could, however, only be obtained if the weld was heated to near the melting point of the steel, and if the carbon was considerably segregated in the bars at the start, for the first effect of the high temperature would be to promote diffusion rather than the contrary segregation and Equation. It is gratifying to learn from Dr. Ruder&apos;s remarks that his researches have resulted in no disagreement with the few points brought out by the writer&apos;s experiments. In addition to the three forms in which nitrogen may occur in iron that he mentions, it would seem that a fourth form is often found; This is apparently a eutectoid, like pearlite, and sometimes almost as coarse as the massive cementite seen in soft steel sheets that have been annealed for a long time. One of the things needed in the metallographic study of steel is an etching reagent that will distinguish definitely between nitride in this form and the more common pearlite or cementite.

Jan 6, 1919

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

By Hong N. Vu, Jitka Jandova

"Gypsum and limestone methods were examined in this study to process zinnwaldite wastes originating from dressing Sn-W ores mined in the Czech Republic. These wastes containing 0.20-0.30% Li and 0.10-0.20% Rb were subjected to magnetic separation to obtain a zinnwaldite concentrate with 1.36% Li and 0.94% Rb. It was observed that processing of the zinnwaldite concentrate with gypsum resulted in almost 96% recovery of Li into aqueous liquors, whilst rubidium extraction was only 25%. At the same time, it is possible to extract almost 92% Li and Rb from the identical zinnwaldite concentrate if the concentrate is processed by limestone method. Lithium carbonate, a final product of both methods was recovered from the refined sulphate solution using K2CO3 as a precipitation agent and/or from unrefined hydroxide solution using gaseous CO2. In the continuation of this study, rubidium will be separated from carbonate solutions after Li2CO3 precipitation as RbAl(SO4)2, an intermediate for Rb2CO3 production. IntroductionLithium is used as an alloying constituent in lightweight alloys, as a heat transfer medium in nuclear reactors and as a component in primary and secondary batteries. With the development of a new generation of electric vehicles, the lithium demand will dramatically grow. Lithium chemicals find extensive application in many industrial branches such as metallurgical, glass, ceramic and pharmaceutical industries. Rubidium compounds are predominantly used in psychiatry and medicine, in magneto-optic modulators, solid-state lasers, phosphors and components of electrolytes for fuel cells. The four most important lithium minerals are amblygonite, spodumene, petalite, and lepidolite. Spodumene LiAlSi2O6 (6.0-7.5% Li2O) and petalite LiAlSi4O10 (3.5-4.5% Li2O) belong to aluminosilcate minerals. Lepidolite (Li.Al)3(Al.Si)4O10(F.OH)2 (3.30-7.74% Li2O), lithium mica, is the most important representative of the mica minerals, a subgroup of the aluminosilicates. It frequently contains 3–5% Rb2O and eventually caesium. Zinnwaldite, which has the general formula K(Li.Al.Fe)3(Al.Si)4O10(F.OH)2 (2-5% Li2O), is regarded as a variety of lepidolite with a high iron content. Commercial amblygonite is a complex phosphate (Li.Na)Al(F.OH)PO4 (up to 9.88% Li2O), however, its deposits have not been commercially exploited because of their small size. Natural brines with a high lithium chloride content are important in the industrial production of lithium [l]"

Jan 1, 2008

By J. A. Herrick Nashua

IN this country steel made in a Siemens furnace or Bessemer converter, is generally tapped into a ladle or shoe, and then drawn through an aperture in its base into the various moulds. In order to regulate the flow of the molten mass a refractory valve is arranged at the aperture. A plumbago nozzle is fixed firmly in this aperture, and a stopper of like material is fitted to it, making a socket valve. In order to raise and depress this stopper at will, a rod is fastened-to it, extending through, the metal and over the brim of the ladle, where it is bent back in a half circle and secured in a slide. This slide plays vertically in a frame, permanently fastened to the outside of the ladle, and is moved by a lever having as a fulcrum a pin fixed in this frame, one end, of the lever being temporarily fixed to the slide, and the other end being moved by hand. Reference being had to the drawing (see Plate 1, Fig. 1), E is the nozzle, D is the stopper, A is the rod, protected as hereinafter described, C is the cast-iron framework, B is the wrought-iron slide, B&apos; is the offset into which the rod, A, enters, and is secured in the usual manner by a key, a. Section J, K, shows the manner of hanging the lever. J is a pin attached to the slide by which the end of the lever raises the slide, B. J is the fulcrum fastened to the frame, C. K (Fig. 1) is a hand-nut fastening the slide, B, to the frame, C, at will. Fig. 2 is a side elevation of ladle, showing the outside working of the parts above described. It is the common practice to protect the rod, A, by a coating of clay and fire-sand, kneaded to the right consistency and applied to the rod, and then thoroughly dried. Just before casting, the plumbago stopper, D, is heated at its extremity to redness separate from the ladle and, at the moment of pouring, is placed in the ladle and slide, and adjusted as well as practicable. Some very serious defects ensue, causing much trouble and vexation as well as actual loss. The fire-clay coating in drying becomes cracked and seamy, and at its best is more or less loose on the rod. The hot metal sometimes cuts

Jan 1, 1879

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6&apos;7 grain boundaries and possibly twinning planes.8&apos;9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5&apos;6&apos;9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By L. C. Clare

In a meeting of this kind where everyone present is connected with or engaged in coal mining, and where each one is present with the set purpose of learning new thoughts or ideas, the subject of the saving of life by any method in the industry is a vitally interesting and important one. On the cost per ton basis, it mounts to a formidable figure especially so during these days of depression and stagnant, or no business. But entirely outside of the human side of the question, to lose lives would cost more than saving them. Your insurance under haphazard safety measures would mount, loss of time due to accidents would impair efficiency among employees and the breaking of the morale of the staff, due to criticism of lax methods would cost more than an efficient safety program. Taking it for granted that most of you are looking at the question from the viewpoint of a yearly or five-year cost sheet, and that at this time you are doing all that can be done without bringing a ruinous cost upon your companies, I can offer only one suggestion: Raise the quality of your safety, or lower the cost. In this meeting, there should be no question of standing still or retreating in the quality of safety, so I will amend the suggestion with "Raise the quality and lower the cost." We have learned that when the coal beds were forming, nature sealed them in with a strata of mud that the ages have turned to shale, sealing them effectively against the deteriorating influences of the air. Mudite is carrying out nature&apos;s plan of coal preservation to the inside of the coal mine. Text books teach us that a large proportion of the vegetation that forms our present coal beds grow on what might be termed mud, later falling and being buried practically where it grew by mud, then on being subjected to heat, pressure and time, was changed to coal. The mud being subjected to the same three forces forms our present shale stratas. Now if nature saw fit to use this solidified mud as a preservative through countless centuries, isn&apos;t it reasonable to expect that occasional coatings on the ribs and roofs of entries and rooms will aid materially in preserving our coal and coal dust? Nature took mud and formed it into shale; mudite takes the shale, reduces it into dust, adds water and makes a mud, applies it to the ribs, roofs and floors of the mine in a thin coating

Jan 1, 1925

By Richard J. Mainiero, James Q. Wheeler, Lewis H. Kopera, Yael Miron

The research reported here was part of the effort to evaluate the safety of a process to recover TNT from MK-9 depth bombs by the autoclave melt out process. In this process the depth bombs are heated to 121°C so that the TNT will melt and run into a vat. Unfortunately, asphalt lining the inside surface of the bomb also melts and flows out with the TNT. It is not known what effect the asphalt contamination and the higher than normal process temperatures (12°C) would have on the sensitivity of the TNT. Testing was conducted on molten TNT and molten TNT contaminated with 2 pct asphalt at 90, 100, 110, 120, 125, and 130°C. In the liquid drop test apparatus with a 2 kg weight, the molten TNT yielded a 50 pct probability of initiation at a drop height of 6.5 cm at 110°C,decreasing to 4.5 cm at 130°C. Asphalt-contaminated TNT was somewhat less impact sensitive than pure TNT at temperatures of 110 to 125°C, but became more sensitive at 130°C; 50 pct probability of initiation at a drop height of 7.8 cm at 110°C, decreasing to 3.3cm at 130°C. In the card gap test, the molten TNT detonated at high velocity for a gap of 0.25 inches at 90 to 125°C and detonated at high velocity for a gap of 0.5 inches at 130°C. For gaps of 0.5 to 3 inches at 90 to 125°C and 0.75 inches to 3 inches at 130°C, the TNT did not detonate at high velocity but produced a violent explosion that caused significant damage to the test fixture. For gaps of 4 inches the TNT did not react. In the gap test there was no significant difference between the pure and asphalt-contaminated TNT. The thermal analysis test results showed that when asphalt is present in TNT, it greatly accelerates the exothermic decomposition of TNT, starting at temperatures near 200°C. The research demonstrated that asphalt-contamination of recovered TNT does not appear to have a significant effect on TNT shock sensitivity, but does adversely affect impact and thermal sensitivity. The results also showed that molten TNT seems to be more shock sensitive than previously suspected. It appears that at relatively low shock stimulus levels, the molten TNT may be undergoing a low velocity detonation, wherein the shock wave traveling through the gap test pipe cavitates the molten TNT, greatly increasing its sensitivity.

By William Kent

In a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on " Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron procluced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the " furnace hook," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable callses which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wetor dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1879

D. EPPELSHEIMER, * Middletown, Ohio.-The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in. a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them

Jan 5, 1919

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By William Kent

(Read at the Amenia Meeting, October, 1877.) IN a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on "Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron produced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the "furnace .book," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable causes which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wet or dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third. class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1878

By J. P. Dovel

HAVING been requested to prepare a paper referring especially to my patents as applied to blast furnaces, I shall confine my discussion to those improvements and inventions pertaining directly to the blast furnace itself, omitting a number of patents pertaining to blast furnace operations. I spent the early part of my life in the construction of blast furnaces, from rivet-heating to drafting and designing, much of the work relating to repairs and rebuilding. Later, as I became more interested in maintenance and operation of a group of blast furnaces, one fact especially made a lasting impression on me, namely that a very expensive piece of equipment was very short lived, and the expense of replacement, relining, etc., in many instances consumed most of the profits made while in actual operation. As far back as 1910, I began to lay plans to build with a view to permanency and not merely for a blast, the common expression at that time, which really meant only one or two years in southern practice. Since we did not then blow so hard most failures occurred in the bosh and hearth. The failure of either generally meant a complete new lining, as the inwall did not look good enough to last another blast. At that time we were using two types of hearth, one of heavy steel plate protected by well and sprays on the outside, and .one of heavy. cast iron, made in sections and bound together with wrought-iron bands. The former type proved dangerous, for if the iron should come through, as it frequently did, it would cut away the steel plate, quickly turning large quantities of molten iron into the water, causing a severe explosion and costly repairs. The cast-iron type gave trouble also by the iron finding its way through the joints between the sections, which was&apos; not so serious; since the iron would not cut away the heavy cast-iron sections very quickly, and generally caused only small damage, and repairs-were easily made. Both types have been improved; the former by the introduction of cast-iron -water-cooled plates, placed on the, inside of the steel, jacket. This has proved to be very good construction, but has no real claim to permanency: As the cast-iron plates cannot be replaced from the outside, therefore the operator must assume that some time, at no late date, he must replace them from the inside, which will mean a blowing out of the furnace. The heavy cast-iron hearth has been improved by making the

Jan 1, 1928