Search Documents

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By A. R. Elsea, C. C. McBride

HIGH-TEMPERATURE alloys, that is, alloys that are strong at high temperatures, have become increasingly important with the development of modern aircraft engines. Many alloys of this type are available. However, metallurgists do not have a clear understanding of the phases or structures which are responsible for these high-temperature properties. If these basic factors were understood, it might be possible to make better or cheaper alloys for service at high temperatures. For this reason, an investigation of the fundamental factors promoting high-temperature strength in alloys was started at Battelle Memorial Institute. This was to have included a study of the relationship between the structure and properties of cobalt-chromium base alloys of the vitallium type. It soon became clear that the structure of vitallium is quite complex and that the equilibrium diagrams which should explain these structures were unreliable. As a result, the cobalt-chromium binary diagram was determined as the first phase of this investigation1. This diagram is shown in fig. 1. During the study of the cobalt-chromium binary system, it was learned that these alloys may pick up considerable nitrogen when melted and heat treated in air. The extent to which nitrogen affects the various reactions in cobalt-chromium base alloys was not known, but there were indications that this impurity might be responsible for some of the erratic test results obtained for vitallium. Consequently, nitrogen was the first ternary addition studied. Thereafter the work was extended to ternary additions of iron and of nickel. This paper describes the investigation of the effects of nitrogen, iron, and nickel upon the reactions in cobalt-chromium alloys with 80:20 and 68:32 cobalt-chromium ratios. Experimental Work Alloy Preparation: A series of cobalt-chromium base alloys containing various amounts of the third element being studied were made for both the 80:20 and the 68:32 cobalt-chromium ratios. Electrolytic chromium, cobalt, and iron, and reagent-grade nickel powder were used as melting stock. Table I contains the chemical analyses of these materials. The charges were melted in alun-dum thimble crucibles which absorbed chromium oxide and effectively deoxidized the melts. These crucibles were supported by close-fitting graphite sleeves so that if they cracked during melting the metal would not be lost. Carbon increases, during

Jan 1, 1951

By T. S. Washburn

Deoxidation is one of the most complex metallurgical operations in the basic open-hearth process. The necessity for deoxidation arises from the fact that the refining operations that precede it require the oxidation of the steel bath. when the refining is completed and the desired composition of the bath has been obtained with respect to the elements subject to control by 'oxidation. there is usually an excess of oxygen present in the bath from the standpoint of the amount desired in the finished steel. The objectives of deoxidation are to control the amount and type of oxides and, although not directly ilnp1it.d by the term or always considered as a Part of the process, to control the amounts of gases such as hydrogen or nitrogen that will be present in the finished steel. There are other aspects to be consideretl in connection with deoxidizing procedures. In addition to the primary objectives of oxide and gas control. the composition of the steel is affected by the elements introduced during the deoxidizing process. Factors in furnace operations are likewise involved, such as slag composition, temperature control. arid heat time. .ill of these should be considered in establishing the most satisfactory deoxidizing procedure for each grade of steel. The purpose of this paper is to outline the objectives of deoxidation as related to steel characteristics, and to summarize the factors in furnace practice and the economic aspects to be considered in connection with deoxidation procedures. Objectives of Deoxidation The primary objectives of deoxidation are the formation and elimination of oxides. The amount of oxygen present in the bath prior to deoxidation is an important factor, since it is the basis of any deoxidation procedure. The oxygen content of the bath is primarily a function of the carbon content, although it is affected also by the temperature, the oxidation of the slag, and transient conditions within the furnace. The relation of oxygen to carbon in the bath is shown in Table I. Table I shows that under actual operating conditions, the amount of oxygen present in the bath is higher than the theoretical amount. This relation would be expected, since the bath is in a state of metastablc equilibrium during the period that the carbon is being eliminated. The most important feature demonstrated by this table, however, is the rapid increase

Jan 1, 1945

By G. Sachs, L. J. Ebert, W. F. Brown

INTRODUCTION ISOTHERMAL transformation, or "austempering," of a carbon-containing austenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.1 Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4-5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.6-7 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels.8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140). The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1948

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By F. E. Griffith

Several disastrous and a great number of near-disastrous mine fires have been started by igniting the combustible conductor insulation and outer covering of trailing cables. Those who have had experience in fighting such fires know that they are extremely difficult to combat and extinguish owing to the irritating and noxious gases, fumes and vapors evolved from evaporation, distillation and combustion of the sundry compounds used in the construction of cables. When electric-motor-driven coal-cutting machines were first introduced in coal mines, the electricity was transmitted to the apparatus by two single-conductor trailing cables. Later, two-conductor parallel and concentric types were developed. These early cables were made with the materials available at that time with relatively little thought given to using new materials or utilizing the old to the best advantage. The copper conductors were stranded to give flexibility, but there were too few strands and the method of laying them was such that they did not endure well the stresses of twisting and pulling, to which trailing cables used in mines are usually subjected. The rubber insulating compounds used were not satisfactory in resisting water, high temperature, and the crushing stresses encountered in mine service. The outer coverings were cotton or jute braids saturated with tars or asphalts having relatively no abrasive resistance. In fact, the only consideration given to trailing cable design because of its extremely short life, was to construct it at the lowest possible cost. With increased electrification and mechanization, more serious problems were encountered. Cables used in mines were exposed to more severe conditions than in any other industry. The excessive overload currents, poor heat dissipation, severe abrasion, crushing loads from falling material, runovers, and any of the other things that tend to destroy cable, called for vast improvement in trailing cable design for mine use. About 1918, one manufacturer who recognized the need for improving the toughness of cables in order to obtain greater safety and longer life, developed a special rope-stranded conductor, a superior rubber insulation compound and a tough rubber sheath or jacket compound. As a result of this type of construction, broken conductor strands were practically eliminated, the insulating material withstood high temperature without undue disintegration, and the jacket, similar to that used for automobile tire tread, had high abrasion resistance, high tear resistance, and was waterproof. While the initial cost of these cables was higher than the jute-filled braided types, this disadvantage was more than offset by increased safety and longer service. Cables with these improved characteristics were first installed in mines in 1920. Since 1930, the use of braided trailing cables in coal mines has been almost completely supplanted by the more superior types, employing high-grade rubber compounds for insulation and sheath. The next steps taken to improve the

Jan 1, 1949

By William Metcalf

William Metcalf, Pittsburgh, Pa. : In rising to discuss Dr. Dadley's paper, I feel somewhat as I did at the Baltimore meeting —that a "crucible" man has no right to interfere in a "Bessenier" discussion; yet having read the paper very carefully, I feel impelled to say something, for two reasons: First, because I believe Dr. Dudley is entirely on the right and having undertaken and partly accomplished a great work, he .is entitled to the help of all who have experience in these matters; and second, because the data given force me to colicur in Captain Jones's opinion that the analyses are incomplete, since they ignore sulphur, copper, nitrogen, and possibly other injurious elements. In an experience of fourteen years, and with probably more than a hontlwl tests, we have never found the chemistry and the of crucible steel to disagree. If in any cave a disagreement tins sp- . peared, it has been our invariable custom to go over all our physirtal testa with great care, and if we found no error, then to refer the matter back to the cherubt, who has invariably found some unexjmted element to account for the trouble. It is only just to the chemist to say here, that ordinarily be is only expected to determine phosphorus, silicon, sulphnr. Generally the metals, with the exception of manganese, are not looked for, although a watch is usually kept for copper and arsenic. Further, in most cases we have found our own work more liable to be faulty than the chemist's. Having arrived then at such a degree of experience that we can preJict the analysis from our tests, or our tests from the analysis, with almost absolute certainty, I can see no reason why the same results map not be attained in the Bessemer practice. But two things are essential, neither of which we have here; first, cornplete analyses; and second, a record of the nature of the blow, the heat at which the ingots were bloomed, and the mile finished,—in short, a complete history of the This latter is quite as essential as accurate and complete analyses. Dr. Duclley ignores sulphur and copper on fair enough grounds commercially speaking, bnt when he announces so gmve a conclusion as he has reached, in a scientific way, the omission of any elementn that, may affect the conclusion is hardly justifiable. His diEerenvcs of phosphorus units, which I milst term units of rottenness 83 fr os phosphorus is concerned, and which I am sorry be did not llama wnits of alloys,—are very small, and if eulphur and copper hod been inclurlid they might havo upset hie conclusions sitogether, The

Jan 1, 1881

HeRbeRT Haas,—(communication to the Secretary*).—Fig. I plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would be well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that '(two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saying that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the South-, west, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market. The greater number of power plants range in size from 300 to 1,000 hp.; the average size of the central station, on a basis of all central stations in the United States, not greatly exceeding 500 kw.; in these sizes it is hard for steam engines to compete with Diesel engines, unless fuol oil prices are excessively high, and coal prices very low, or the exhaust steam is used for heating purposes.

Jan 1, 1917

By William C. Marshall, Frank G. Norris

THE term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open hearth shop is dependent on the blast-furnace capacity rather than on its own needs for the amount of iron available are among those which, in contrast to "unit operations," we have chosen to call "total operations," Many of these problems, such as charging delays and the general mechanical problem of material handling, are so familiar that merely to define "total operations" brings them to mind. These problems are of such importance that already they have received careful thought and study and probably will merit further study. As will be shown later, these mechanical problems are so intimately related to metallurgical problems of total operations that the effect of certain changes cannot be ascribed with certainty to either a mechanical or a metallurgical cause entirely. Although the problems coming under the general term of "railroading" are included in the problems of total operations, two others are selected for the discussion of this paper. One of these is strictly a problem of composition; the other is strictly a problem of tonnage production. The problem of phosphorus is present whenever basic open-hearth slag is used in the blast-furnace burden. This practice has not secured universal acceptance chiefly because of difference in preference for high-manganese or low-manganese pig iron. If high-manganese (2.00 per cent) iron is to be made, open-hearth slag as a source of manganese is usually cheaper than man

Jan 1, 1943

By J. E. Gould, H. J. Hand

MANY independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final deoxidation In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding over-deoxidation to minimize the amount of inclusions present and to make as sound a steel as possible For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or long FeO values The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishing the state of oxidation at a given time Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors Data obtained are from actual furnace operations, the metal test being of the spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States Steel Corporation This method of taking open-hearth metal temperature was invented by Collins and Oseland,1 and was developed into its present form by L 0 Sordahl,2 of the Research Laboratory The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications 3,4,5 Slag components were obtained by chemical analysis Data were taken from four 165-net-ton furnaces during the working period of the heat Recognizing that additions of ore affect the

Jan 1, 1942

ON Oct. 5, 1926, the day before the general ses-sions of the fall meeting of the American Insti-tute of Mining and Metallurgical Engineers at Pittsburgh, a round table conference on the combus-tibility and testing of coke was held at the Bureau of Mines Experiment Station. There were about fifty present, with A. C. Fieldner, chief chemist of the Bureau of Mines, as chairman. The following organi-zations were represented: American Institute of Min-ing and Metallurgical Engineers, American Society for Testing Materials, American Gas Association, Eastern States Blast Furnace and Coke Oven Association, Gas and Fuel Division of, American Chemical Society, and Southern Ohio Pig Iron and Coke Association. In opening the proceedings, Mr. Fieldner explained that the meeting had been called at the suggestion of several members of the Institute and members of other organizations. The subject is of interest to the pro-ducer and the user of coke whether it be in a blast furnace, cupola furnace, house-heating furnace, open grate, gas producer, or in a water-gas generator. There has been much confusion on this subject largely because there is no common definition of combustibility. Does the blast-furnace superintendent, the coke-oven operator, and the fuel engineer have the same under-standing of the term "combustibility"? If a common understanding can be reached, many differences of opinion will disappear. COMBUSTIBILITY OF COKE R. H. Sweetser of Columbus, Ohio, disagreed with the statement of P. H. Royster, T. L. Joseph, and S. P. Kinney in Reports of Investigations, Serial No. 2524, of the Bureau of Mines, in which it was stated that the coke-oven op-erator cannot change coke combustibility by modifying oven practice. Mr. Sweetser held that the coke-oven man can change the combustibility of coke. Blast-furnace men know that coke that will burn easily with low pressure and will. come down in the regular way in the furnace can be pro-duced from a given mixture of coal. His idea of the combustibility of coke is the rate of flow through the com-bustion zone of the blast furnace. If the coke does not pass through in normal manner it is highly incombustible. H. J. Rose of the Koppers Co., Pittsburgh, objected to being pinned down so closely on this phase of the com-bustibility and incombustibility of coke. Coke-oven men are frequently obliged to change oven conditions to make a coke which gives blast-furnace men what they want. The size of the coke and the screening have an important bear-ing on combustibility, and there are many cases on record where by simply changing the different sizes of the coke, everything worked smoothly, and that is a much more combustible coke.

Jan 1, 1927

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Arthur Phillips, E. N. Skinner

DURING the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson1 who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.015 per cent at 1050°C. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000°C. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hewitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of minute concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicroscopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By Samuel E. Doak

The utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose, loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 11/2 per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In modern practice the percentage of sulphur in the cinder is rarely as great as six, and seldom lower than one and one-half. Average analyses for iron, silica, and sulphur of the cinders that have come under my personal observation are as follows:

Jan 1, 1916