Search Documents

By Afrodite Ntziouni, Vassilia Kasselouri – Rigopoulou, Athanasia Kyritsi, Konstantinos N. Pistiolas, Stamatia Gavela, Konstantinos Kordatos, Lazaros Iliadis

"The present study deals with the production and characterization of rice husk ash (RHA) and its use in the synthesis of zeolite of type ZSM-5. Rice husk was combusted in various temperatures with aim to find the suitable conditions for the production of amorphous silica. The resulted amorphous silica ash was then utilized as a starting material for the synthesis of ZSM-5 zeolite using the low temperature and atmospheric pressure process. The method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced material was characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM).IntroductionRice husk is a major by-product of the rice-milling industries and it is usually used as a fuel for steam generation due to its high calorific power. During its combustion, rice husk ash (RHA) is produced. Knowing that the annual rice world production is over 615 million tons (2005), thus resulting in a potential production of more than 22 million tons of RHA [1], it can be understood that the RHA disposal is a crucial issue towards the environmental protection. However, due to the high silica content, RHA can be used as an alternative cheap source of silica for many uses, including as filler in polymers [2], concrete [3] and synthesis of zeolites [4-7].The burning of rice husk in air results in the formation of RHA with content in SiO2 that varies from 87 to 97% depending on the burning conditions, the rice variety, the climate and the geographic area [8]. Some small amounts of inorganic impurities are always present in the ash along with unburned carbon. The unburned carbon can be removed from the ash by further heating treatments in high temperatures, but this usually leads to the crystallization of the amorphous silica to cristobalite and/or tridymite [9]. The crystallization of the contained silica of the ash is also occurred when the burning conditions of husk are uncontrolled [10]. This crystallization is a disadvantage towards the preparation of silicon based materials, because the silica ash is rendered inactive in its crystalline form [11]."

Jan 1, 2008

By S. Stutz

COAL, like most other minerals, only exceptionally occurs in a sufficiently pure state to he directly available for general manufacturing purposes. And even where this is the case, the small coal or slack is usually more impure than the lump coal, as the slate, clay, etc., from the roof and bottom of the vein become mixed with it in the handling it undergoes. These impurities often exceed ten or more percent in addition to the impurities of the coal itself. The most common impurities of the coal are slate, or shale, clay, and sulphur. The latter occurs in different forms, but most frequently as bisulphide of iron, or iron pyrites, and as sulphate of lime, or gypsum. In both cases the impurities add greatly to the amount of ash, and where they are present in considerable quantities the raw coal, and still more the coke made from it, is unfit for the, manufacture of iron. Coke will contain on an average at least ;fifty per cent, more ash and sulphur than the raw coal from which it is, made. To the manufacturer of iron every additional per cent. of ash which his coal or .coke contains is a source of additional expense, seemingly small, and yet very important in the aggregate. In the blast-furnace, for instance, the ash must be heated up to the melting-point, and, since it is composed largely of refractory substances, the consumption of carbon in melting it will be equal to at least one-half of its weight ; that is, a certain part of the coke is consumed for the melting and fluxing of the ash and is lost. Besides this, it is well enough known to the-iron-master that coke containing less ash makes the slag or cinder more liquid and less inclined to stick to- the walls of the furnace. Fuel containing much sulphur produces generally a white iron, poor in carbon, while from the same ore and flux, with a pure fuel, a good foundry iron might be obtained. The work of separating slate, sulphur, etc:, from the coal 'has as yet only been succesafully accomplished by the washing process. This process depends for its success on the differences in the specific

Jan 1, 1881

By Eric R. Jette, A. G. H. Anderson

During the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth—why and how it occurs—were treated in papers by Howe,' .Jeffries,² Sauveur,² Chappell,4 Beilby,5 Mathewson and Phillips,6 Mc Adam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,l0 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size sperified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filamentsl1 wherein it is important to prevent "sagging" between consecutive turns of the helix.12 This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,'? in the hardening treatments of high-speed steels,14'15 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is

Jan 1, 1938

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By Morris A. Steinberg

Because of the broad scope of my topic I will discuss my subject from the point of view of a present status of the metallic materials that are used in structures and will dwell primarily on those structures related to high- performance aerospace systems. Thus, I can best portray the status of these structural materials as related to existing transportation systems, delineating some of the highlights of alloy development, fabrication, and properties obtained. I shall point out what are, in my opinion, the needed solutions to pressing unsolved metallurgical problems connected with certain selected metals: aluminum alloys, beryllium, titanium, steels, superalloys, refractory metals and some metal-matrix composites. Aluminum Alloys For a number of years a series of strong aluminum alloys used for airframes has had an important bearing on the development of minimum- weight, highly efficient structures. Among these alloys are such familiar ones as 2024-T3, 2014-T6, 7075-T6, 7079-T6 and 7178-T6. A review of the development and use of strong aluminum alloys in aircraft structures indicates that before about 25 years ago there was very little application of products other than forgings in the high-strength tempers produced by precipitation heat treating to T6- or T8-type tempers. 1 As stated by Dix in 1944, "There has been a gradual evolution in engineering viewpoint regarding the mechanical characteristics which are required in a structural material suitable for aircraft. Formerly, emphasis was placed on a generous spread between yield and tensile strengths, on elongation, on impact strength and on resistance to corrosion. Aircraft structural engineers still differ widely as to the importance which they attach to these proper tie.” 2 It is fair to say that this evolution is still taking place, that the problem is much the same in 1970 as in 1944 - except that strength levels have advanced some - and the question remains as to how far we can go in that direction. In the meantime, a new group of alloys has received acceptance and widespread use. The first alloy of this group, 7075-T6, was formally introduced by Dix's 1944 paper. The drastic changes that have taken place in the size and configuration of components employed in air-

Jan 1, 1971

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By C. H. Li, R. J. Stokes, T. L. Johnston

A portion of the Ni3Cr-Ni3Al phase dzagram has been investigated, including the precipitation of 1 (Ni3Al) as well as the existence of ordered Y (Ni matrix), Extensive metallographic studies by electron microscopy have been carried out and X-ray diffraction diagrams have been taken at both elevated and ambient temperatures, No long-range ordering of the phase was found above 893°C (1639°F) in the compositional range investigated. The high rate of formation of the ordered ?1 phase upon quenching has been confirmed, a phenomenon which up to the present Lime has retarded the understanding of this phase diagram, Specimens with controlled amounts of ?1 exhibited up to a six-fold improvement in yield and creep strength compared with single-phase Ni-Cv-A1 alloys. MOST of the important high nickel heat-resistant alloys are related to the nickel-chromium-aluminum system. One of the important functions of the aluminum, often accompanied by titanium, is to produce a precipitate of the very fine ?1 phase (Ni3A1, X) where X may be Ti, Cr, or other elements. A number of investigators1-" have demonstrate the presence of y' in these alloys but most of their materials contained large amounts of other elements resulting in appreciable amounts of con- fusing phases such as carbides. Further clouding of the precise role of y' has been the suspected existence of an ordering reaction in the y matrix itself, ro-3,12-17 It appeared from these investigations that aluminum in Ni-Cr alloys would raise the ordering temperature of the matrix from 540°C at NisCr to 1300°C at Ni,Al. In support of this possibility, the matrix phase in the parallel Ni-Fe-A1 system is ordered to very high temperatures.1 OBJECTIVES OF THIS RESEARCH From this survey of the literature it appeared desirable to conduct an investigation of the simple Ni-Cr-A1 system using the alloys of the highest available purity to avoid the complication of foreign phases and thereby isolate the structures in the Ni-Cr-A1 system. Procedures were developed to study ? - ?o and ? - ?1 equilibria. Preliminary mechanical tests at elevated temperatures were also conducted.

Jan 1, 1962

By Clarence Balke

SMALL buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreci-able size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numer-ous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the- entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects clue to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By Frederick Rhines

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ? in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activa-tion heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. Much of the argument concerning the properties of metals that deter-mine D and Q has been drawn from data in which variations of the quan-tities with concentration are unknown, for these data- have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concen-trations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By K. O. Bennington

[Thermodynamic properties of two amphibole asbestos minerals were determined by the Bureau of Mines. The enthalpies of formation were determined by the hydrofluoric acid solution calorimetry method. Heat capacity measurements were made with an adiabatic calorimeter over the range of 5 to 315 K. High-temperature enthalpies above 298 K were determined with a copper-block drop calorimeter to 852 K for amosite and to 902 K for crocidolite. Thermodynamic data determined for amosite of the composition Fe5+2.2766Mg1.5209 Fe+03.12Mn0.0825) Si7.9163Al0.0837022.0363)(OH)1.9637 are: S°298 = 168.8 ± 5 cal/deg-mole; ?Hf°298-15 (elements) = -2419.24 ± 2.95 kcal/mole; ?Hf298.15 (oxides) = -30.92 ± 2.47 kcal/mole; and ?Gf° -2260.1 kcal. Corresponding data found for s3 ,1s = crocidolite of the composition (Na1.9Ca0.1)(Fe2+.024Fe2.5 01Mg0.475) (Si7.9713024Fe+2 2.501Mg0.475) (Si7.971 Al0.029022.095) (OH)1.905 are: S2.98-15 - 161.1 ± 4 cal/deg-mole; ?Rf° 2 298.15 (elements) = -2433.56 ± 2.99 kcal/mole, 10298.1s (oxides) = -87.69 1.70 kcal/mole, and ?Gf°298.15 = -2269.8 kcal.] Calorimetric values from this investigation were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and the constituent oxides.

Jan 1, 1978

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By T. R. Graham, R. S. Dean. J. R. Long

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By R. S. Dean. J. R. Long, T. R. Graham

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By S. F. Radtke, J. A. Snyder, R. M. Scriver

An automatic, continuous casting arc furnace employing a nonconsum-able electrode and a direct current arc has been constructed and operated successfully for titanium. A comparison of the properties of arc and induction-melted titanium indicates that where high ductility, formability, and toughness are required, arc-melted metal is preferable. BECAUSE of the reactivity of titanium metal with all known refractories and the common atmospheric gases, melting of the metal presents numerous problems. It is necessary to provide an inert atmosphere in the furnace as well as a crucible material that will not react with the molten metal, if a ductile ingot is to be produced. Two special furnaces have been developed that meet the requirements and one, the induction heated graphite furnace, has been described in some detail.' Little information is available for sizable units wherein power is applied to the melt through an arc, and the dearth of technical information on such a furnace prompted this report. It has been demonstrated clearly that arc melting produces titanium metal with superior toughness, ductility, and formability. To produce titanium ingots with these properties, an automatic, continuous casting arc furnace has been developed and is described herein. The history of arc melting may be traced to 1800, when Sir Humphrey Davy2 first experimented with Volta's electric battery and found that light could be produced and an arc formed between two carbon points attached to the cell. The discovery of the arc was followed by the design and construction of an arc furnace by Napier," in 1845, for the reduction of metal oxides. In 1853, Pichou' described a similar furnace, although it was not until the discovery of the dynamo in 1867 that the arc furnace could achieve commercial significance. In 1878, Siemens- esigned the first arc furnace intended for the melting of metals and by 1882 had melted steel and platinum successfully. . This was followed by Moissan's" classical work with the arc furnace in 1892. W. von Bolton,' in 1905, found that the arc furnace was suited admirably for melting refractory metals. In his work with tantalum, no suitable refractories for retaining the molten metal were found to exist. Together with Otto Simpson, he developed an arc furnace with a water-cooled copper crucible in which tantalum could be melted without contamination. This technique proved eminently successful. In his paper on the preparation of ductile titanium, Krolle first described an application of the von Bolton furnace to the melting of this metal. The

Jan 1, 1952

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By J. R. Long, T. R. Graham, R. S. Dean

ALTHOUGH considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to 11 pct aluminum, with some incidental information on the single-phase alpha solid solution alloys. Strauss1 gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper5 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50° temperature levels from 400° to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solubility of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 1300°F and higher,

Jan 1, 1947

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By I. Ueda, S. Ishikawa, T. Nagata

“O-SR process” in which the S-Furnace of the Mitsubishi process is followed by existing reverberatory furnaces (RFs) and Peirce Smith (PS) converters has been operated since December 2007. The S-Furnace smelts copper concentrates to produce molten matte containing 58-62%Cu which is then settled in the RFs and converted to blister copper in the PS converters. The SO2 gas generated from the S-Furnace and PS converters is converted to sulfuric acid in the acid plants. In addition to the smelting copper concentrates, the O-SR process has advantages in terms of recycling various waste/secondary materials. Automotive Shredder Residue (ASR) has been treated in the RF to reduce fossil-fuel consumption in RFs, and to recover various metals included in ASR as well, since 1993. Electronic circuit boards (E-scrap) has also been processed in order to recover not only copper but also rare resources such as gold, silver and PGMs since 2013. Strategic modifications have enabled expansion of the processing volume of E-scrap. Enhancing recycling of wastes and scraps from urban mines while reducing the consumption of natural resources in the “O-SR” process will be demonstrated and discussed in the present paper. INTRODUCTION Onahama smelter and refinery has been operating as a custom smelter since 1965. Smelting facilities were subsequently expanded to two green-charged RF furnaces and five PS converters in 1973. Since RF is a conventional old-fashioned smelting furnace that necessarily consumes a huge amount of fuel to smelt copper concentrates, saving fuel cost has been an important objective. In early 1980’s the fuel was changed from bunker oil to pulverized coal, while utilizing the combustion heat of waste tires. Furthermore, treatment of combustible waste such as shredder residue (SR) was initiated in order to save fossil fuel for smelting concentrates in the RFs. Since enhancing of the treatment of SR requires a reduction in concentrate smelted in the RFs, most concentrates were dried and injected through tuyeres into the PS.converters. These modifications enabled to reduce the amount of the pulverized coal combustion and to increase SR treatment in the RFs. SR treatment capacity has increased to 12,000mt/month because the SR market has grown after the enforcement of the Vehicles Recycling Law. Such business environment has been attributed to establish the thermal-materials recycling system of SR in which the RFs have changed their role from copper concentrates smelting furnaces to waste materials combustion furnaces.

Jan 1, 2019