Search Documents

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

THE first session of the Institute was held on Tuesday evening, September 16th, in the William Molson Hall, of McGill University, Dr. T. Sterry Hunt, Chairman of the Local Committee of Arrangements, in the chair. Dr. Hunt introduced Monsieur S. Rivard, Mayor of Montreal, who spoke as follows : GENTLEMEN: We welcome you with pleasure to our city, and we are proud to find that you have deemed it worthy of your visit. I understand that your association was founded in 1871 with some thirty courageous members, and that so valuable has it been esteemed, and so attractive was it found, that nearly one thousand have now enrolled their names as members and associates. But we must regard your profession as dating back to the stone age and mingling therewith ; how remote that is none of us can tell. Much of civilization is due to the discovery of metals, and the magnitude of our works to their widespread abundance. If you have not accomplished what the alchemists aimed at, which was to turn the ruder materials into gold, you manage, by your subtle skill, to turn stones into gold value. Europe has long since been-dug into and perforated with shafts and galleries in search of metals, and great wealth, and power, and comfort have arisen there-from ; but by an increase of knowledge, and more than European enterprise and energy, America is following rapidly in the race, and by means of natural advantages of a geological character has out-stripped the Old World. We are pleased to see you, gentlemen, as an evidence of the unity of this continent. Maps may have various delineations, but the veins and arteries of commerce and the nerves of science knit all together into one social organism with the same vital functions. We live here on the margin of the world, and can claim but a modest share in. the great works of modern times, but such as we have that can interest you we gladly offer for your observation.' Our Victoria Bridge may he considered appropriate, for without mining engineers to precede the civil and mechanical, no bridge would be there to-day. In truth, the same may be said of all works of metal, and of all that are executed by tools and machinery made of metal. The Mont

Jan 1, 1880

By G. H. Khoe

Neutralisation of acid uranium mill tailings with lime or other alkaline materials is usually practised to reduce the dissolved concentration of heavy metals and radio nuclides. Computer modelling of this process was carried out using the geochemical equilibrium code MINTEQA2. Computed dissolved metal and sulfate concentrations were compared with laboratory-based experimental data. It was found necessary to include the modelling of adsorption of trace metals (such as uranium and lead) by the precipitated ferric hydroxide in order to obtain acceptable concentrations in the neutralised liquors. There were limitations of the modelling exercise due to important aspects which were not addressed or properly accounted for such as chemical reaction kinetics and the effect of high ionic strength. These are discussed in the paper.

Jan 1, 1991

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By A. M. Esteves

This paper offers an overview of local content policies and practice in the mining sector. Specifically, the paper aims to answer the question of how national and regional governments, industry and civil society can work together to seek an optimal outcome while pursuing their diverse objectives. The paper begins by defining local content and its scope at the subnational level. Specific recommendations for the design of local content policies to mitigate social, economic and governance risks are developed. The document then offers some recommendations regarding the role of partners in design, implementation, monitoring, and enforcement of local content policies.

Aug 1, 2013

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Pramod C. Thakur

Coal is a major source of energy in the world today and will, undoubtedly, continue to be so for the next few centuries. Naturally, a great number of studies has been made of its physical and chemical properties. Unfortunately, the work on technical properties which influence the mining of coal and the consequent yield of inflammable gases and respirable dust particles has not progressed at a comparable pace. Coal is a brittle material. Irrespective of the mechanism of breaking coal, some dust is always produced. In mining parlance dust is defined as solid particle, smaller than 100 microns (micron = 10-6 meter), in size Coal dust, when raised into a cloud, creates two well known hazards in mines, namely, the coal dust explosion and Coal Workers' Pneumoconiosis (CMP). The latter is, perhaps, the greatest environmental hazard in U.S. coal mines today. In this context it is not only natural but also necessary to investigate the proneness of a coal seam to respirable dust production. It has been established that the amount of dust produced is a function of two groups of variables (1), (2), viz. (1) Material dependent variables, e.g., moisture content, compressive strength, hardness, etc. (ii) Breaking mechanism dependent variables, e.g., type of machine, depth of cut, etc.

Jan 1, 1973

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By D. B. Dreisinger, M. Mokmeli, B. Wassink

Dissemination of selenium and tellurium in sulphide minerals results in the contamination of pregnant leach solutions and electrolytes in the hydrometallurgical treatment of sulphide ores and residues. The selenium and tellurium content of the copper sulphate-sulfuric acid solution may be reduced into insoluble precipitates of copper selenides and tellurides using cuprous ion. This study presents the use of the thermodynamics and kinetics for the removal process of selenium and tellurium in real life application. Dominant species of selenium and tellurium in acidic copper sulfate solutions were identified and the reduction rates of species were compared. The findings were applied to industrial conditions by modeling the Vale’s CRED (Sudbury, Canada) plant’s selenium and tellurium purification circuit. Rate reducing factors on selenium and tellurium removal were identified and discussed.

Jan 1, 2014

By C. C. Popoff

The development of glass-making industries in the Pacific Northwest as well as other industries that use pure silica has been retarded by lack of local supplies of low-cost raw material. Several quartz deposits along the Skagit River constitute the only known source of relatively pure silica within the range of cheap transportation to the Seattle industrial area. Although some silica has been mined from these deposits, very little information regarding their size, grade, and other physical characteristics has been available to the general public. As a part of its program of investigation of the mineral resources of the Pacific Northwest, the Bureau of Mines assigned the writer to examine the Skagit River silica deposits in October 1946. This report presents the factual data obtained from an examination of the so-called Stoner, Bacon Creek, and Pressentin deposits. These deposits are the largest and most easily accessible known to exist in the area. The deposits are near Marblemount, which is on State Highway 17A. They are within 1 mile to 1-1/2 miles of the Skagit. River Railway, which provides transportation to Seattle, a distance of 130 miles. None of the deposits has been developed thoroughly. The Stoner deposit, however, has been developed by a quarry about, 5,0 feet square and has been exposed by hydraulic removal of the overburden throughout a distance of 180 feet along the hanging wall of the vein

Jan 1, 1949

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978

By M. Mai Manga, M. Renaud, A. Faucher, C. Bazin

ABSTRACT Grinding circuits are operated in the presence of disturbances resulting from ore changes and equipment malfunctions, such as hydrocyclone overloading, worn or partly plugged apexes, surging, and internal liner detachment that may cause a loss of classification performance. Metal recovery losses in downstream leaching or flotation circuits justify the development of methods for rapid detection of hydrocyclone malfunction. Two methods are presented in this paper. The first method uses measurements from sensors available in a grinding circuit and the second uses vibration sensors installed on the individual hydrocyclones of a nest.

Jan 1, 2011

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By Charles M. McCulloch

This Bureau of Mines report discusses the principles of using computers to draw maps and plot geologic data of mining areas. The types of maps that can be drawn by a computer are reviewed, using as examples two separate areas where poor roof and gas emissions caused mining problems. Such maps can be used not only to help identify problem areas, but also to predict areas where problems could occur, thus giving mine operators time to work out solutions prior to mining. The average cost of a computer-drawn map for a mine property is less than $100, including computer time and man-hours for data preparation.

Jan 1, 1976

By Fouad Faraj, Julian M. Ortiz

Within the natural resource industries, there is an increasing amount of data and number of variables being recorded when sampling a site. This has made multivariate geospatial datasets more difficult to analyze, in particular the definition of estimation or simulation domains used in geostatistical analysis. Establishing these domains is typically the first step for any subsequent geostatistical workflows or modeling. Domains are traditionally established using categorical data such as lithology, mineralization, or alteration from geological logging and are aimed at identifying distinct populations with particular geological, spatial, and statistical features. The manual logging process is time-consuming and costly but is required because defining geologically homogenous volumes is crucial for the planning, extraction, and processing of natural resources. Classical clustering methods have aided in analyzing the multivariate datasets, but the resulting clusters from these methods do not correlate well with geological logging and do not allow practitioners to input their knowledge of the domain in the clustering process. In this work, a simple unsupervised classification workflow is presented which allows the practitioner to input domain knowledge by selecting relevant variables to cluster reasonable geological domains. This can be used as a tool to aid the manual logging procedure or as a tool to establish domains for different uses such as defining zones with different rock hardness distributions which allows the corresponding volumes to be sent to appropriate mills for efficient mineral processing. The performance of the workflow is assessed on a mining dataset using the geochemical information and validated with the geological logging.

Apr 16, 2021

By Hernani Mota, Eleonardo Lucas, Christ Barriga

Este trabajo técnico presenta los estudios realizados para una caracterización física, mecánica y mineralógica del macizo y material rocoso presentes en una mina en la sierra del Perú, con énfasis en el estudio de las estructuras mineras (tajo, pila de estéril y pila de lixiviación). El principal objetivo fue determinar la influencia que tiene la alteración del pH cuando los agentes de meteorización como las condiciones climatológicas (temperatura y precipitación) someten al material y que puede causar imprevistos en las obras de ingeniería realizadas en minería.

Sep 29, 2023

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971