Search Documents

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By M. T. Hepworth, T. P. Papazoglou

Hydrogen diffusion in hcp and bcc titanium in the temperature range 610° to 900°C was measured by reacting cylindrical specimens of high-purity titanium at constant temperature with small constant pressures of hydrogen of the order of a few Torr. In the range 0 to 6.7 at. pct H in hcp titanium, the diffusion coefficient D in sq cm per sec is given by: where T is in °K and R in cal per g-atom OK. Only three measurements of diffusivity in bcc titanium were made: at 900' : the diffusivity in ß titanium was found to be 1.8 x 10-4 sq crn per sec. McQUILLAN1 has studied the constitution of the Ti-H system and reported the concentration of hydrogen as a function of pressure of hydrogen and temperature. He found hydrogen absorption was reversible and rapid at temperatures above 500°C in both crystallographic modifications, the a (hcp) phase and the ß (bcc) phase, with the latter phase stabilized by hydrogen additions. Wasilewski and Kehl 2 measured the diffusivity of hydrogen in hcp and bcc Ti-H alloys. For bcc alloys, they reacted cylindrical specimens of titanium with hydrogen gas at 1 atm pressure. They measured the rate of absorption of hydrogen isothermally on specimens ranging from zero hydrogen content when above the transformation temperature to hydrogen contents sufficient to stabilize the bcc phase when below the transformation temperature. By integrating Fick's second law for a cylindrical geometry, assuming a diffusion coefficient independent of composition, they calculated diffusivities as a function of temperature. In the range 650" to 1000°C their results in bcc titanium yielded the expression: where D is in sq cm per sec, T in OK, and R the gas constant in cal per g-atom-OK. Their studies on the hcp a phase were conducted by exposing long cylindrical titanium specimens to hydrogen at a sufficiently high pressure to establish a surface layer of fl phase 80 to 120 u thick for the duration of an isothermal experiment. Concentration profiles were then determined by hydrogen analysis from chips obtained upon machining quenched specimens. The diffusivity of hydrogen was then calculated yielding the expression: The present investigation was undertaken principally to redetermine the diffusivity data on a titanium by a direct absorption from the gas phase at sufficiently low hydrogen pressures to avoid the presence of a surface bcc phase and also to check the diffusivity data at low hydrogen concentrations in the bcc stmcture. EXPERIMENTAL PROCEDURE High-purity electrolytic sponge titanium (99.9 pct) of BHN 91 was arc-melted, forged, rolled, and machined into cylinders of final hardness, upon annealing, of BHN 92. Cylindrical specimens of two sets of dimensions were used: 1.524 by 2.931 cm and 1.905 by 3.663 cm diam and length, respectively. The experimental apparatus used for annealing specimens and for admitting known amounts of hydrogen at constant pressure is shown in Fig. 1. In a typical experiment, a specimen was lightly abraded with fine-grain silicon carbide, washed with water and detergent, and then thoroughly degreased with reagent-grade tri-chlorethylene and acetone. The specimen was suspended by a Chrome1 wire in the center of a quartz furnace tube, without contact with the tube, and heated to 925°C (as measured by a thermocouple adjacent to the specimen, outside the tube) for a period of at least 4 hr under a vacuum of from 10-6 to -7 Torr as measured by an ionization gage. The furnace temperature was then adjusted to the temperature chosen for the particular diffusion study and the specimen allowed to equilibrate thermally. Hydrogen was then ad-

Jan 1, 1969

At present the feasibility of developing underground facilities for the storage of a number of products including toxic waste, oil, nuclear waste and low pressure gas is under investigation in e number of countries. A possible method of storage is in large excavations, Preliminary ventilation design work has identified that the climatic conditions encountered within these large excavations are a limiting ventilation pollutant within the ventilation system. This paper examines the design of a variety of sizes of excavation from a ventilation viewpoint. The main phases of an excavations lifetime can be divided into four main phases, these being construction, civil and mechanical fitting, storage, full and sealed. The paper details ventilation design options for the first two phases of e vaults lifetime, giving climatic simulations to assess the likely climatic conditions within the excavations for e number of facility depths. The options for climatic control are given and analyzed by means of climatic simulations techniques. l. INTRODUCTION The feasibility of developing underground facilities for the storage of a number of products is under investigation at present in a number of countries. This paper details a possible design for such a facility where the product is to be stored in large underground excavations. A facility layout has been designed with the aim of allowing concurrent construction and storage operations. Thus from a ventilation perspective the facility consists of two circuits , a construction ventilation circuit and a product ventilation circuit both of which are served by an intake and a return surface connection The construction and storage circuits are considered as independent of each other , any interaction in the form of leakage must be from the construction to the storage circuit. From the facility design a ventilation network was developed to assess the ventilation requirements of the facility. In analyzing the pollutant loads for the construction circuit two pollutants were recognised to be critical to the ventilation design , these being diesel exhaust fumes and heat end humidity. In this paper ventilation design options for the construction and civil and mechanical fitting phases of the excavations are analyzed by means of climatic simulation and options for climatic control within the vaults are outlined . 2. FACILITY DESIGN A schematic diagram of a facility design is illustrated in Figure 1. There would be two distinct ventilation circuits , one to service the construction operations and the second to serve the storage operations which occur concurrently with construction , the circuits are separated by ventilation bulkheads . Access to the facility for intake air is provided by two drifts, one to serve each circuit. Two shafts act as returns to surface. The facility consists of two distinct zones for the storage of two types of product. One type is to be stored in smell linear excavations. The second zone is for the storage of a second product in larger excavations. The maximum cross-sectional area and perimeter for the smell linear excavations are 456.25 m2 and 83.2 m, while for the larger excavations they are 440.1 m2 and 86.4 m. Excavation construction consists of three phases: 1. Initial pilot tunnel development between main intake and return to provide through flow ventilation. 2. Enlargement to produce the required finished cross-section. 3. Civil and mechanical engineering work to fit out the excavation ready for storage. It is proposed to excavate the excavations using drill and blest methods utilising diesel equipment. Spoil is to be transported to surface by a conveyor belt system. At any one time the maximum number of working places requiring ventilation will consist of ; 3 storage sites, 2 excavations under construction, 2 excavations undergoing civil and mechanical fitting. [ ]

Jan 1, 1993

By P. M. Aziz, I. Markson, C. S. Barrett

The abnormal after-effect in twisted wires that occurs when untwisting is interrupted by etching con be brought under control and used to study the mechanical properties of thin surface films and how they are effected by reagents and heat treatment. Results are given of studies of oxide films on high purity aluminum. IF a wire is subjected to plastic deformation by torsion and then released, it untwists in the normal after-effect, but under certain circumstances the untwisting is abruptly lessened or reversed by the application of an etchant to the wire.1,2 This abnormal after-effect may occur, for example, if there is a coherent oxide film on the surface of the wire which is removed by the etchant. Following a suggestion of A. H. Cottrell that predicted this effect, it is attributed to dislocations that had piled up beneath the oxide layer and represents the rapid release of residual stresses caused by these dislocations. When the layer is removed, the stress relief may be by escape of piled-up dislocations from the metal, or by an activation of latent sources of dislocations located at the surface, together with rebalancing of elastic stresses to compensate for the loss of stressed material, as in a residual stress analysis determination, these mechanisms acting singly or in combination.' The slower the attack of the reagent, the more gradual is the stress relief and the smaller the change in strain rate when the reagent is applied. A study has been made of the factors that influence the magnitude of the normal and abnormal after-effects with the object of developing techniques suitable for a quantitative investigation of the influence of various surface films on dislocations in wires, and of the rate and extent of the attack on the films by different reagents. It was found that reasonable sensitivity and reproducibility could be achieved if a suitable choice of variables was made and if these variables were held constant through a series of experiments. The method was then applied to a study of oxide films produced and treated in different ways on the surface of high purity aluminum wires, and to a study of the damage to these films caused by various reagents. Experimental Procedure The material used throughout this work was prepared from 99.9968 pct Al. This high purity aluminum was melted, cast into 1/2 in. diameter ingots, and then swaged and drawn without intermediate annealing to 0.040 in. diameter wire. A sketch of the apparatus employed for twisting is shown in Fig. 1. The test wires were mounted into the apparatus by cementing one end of the wire to the beaker and the other to the tube with laboratory wax of high melting point. The length of the wire between the waxed joints was 4.2 & 0.2 cm. Extreme care was taken during mounting to avoid cold-working the wire. The wire was twisted through 335" in 2 to 4 sec by rotating the pinion on the gear box until the vertical post on the rotating table, which was initially touching the horizontal stop, was arrested by the stop. All the tests were conducted with apparatus and reagents at the same temperature (about 25°C). In all tests, except those where the duration of the initial torque was investigated, the torque was applied for a period of 2 min. At the end of this time the table was rotated back a few degrees away from contact with the stop and the wire allowed to untwist. The after-effects were measured by reflecting a beam of light from the mirror shown on the apparatus. After the wire had untwisted for 6 min, a reagent was carefully poured into the beaker and thereby applied to the surface of the wire.. In some tests the liquid in the beaker was removed after a few minutes and replaced by an-

Jan 1, 1954

By M. Korchynsky

"The key words which characterize vanadium are: unlimited availability, versatility of applications and price stability. The supply of vanadium is assured by diversified sources, distributed all over the globe. The inexhaustible raw materials base is complemented by a strong vanadium industry. Both the fully integrated vanadium producers and converters of vanadium oxide or vanadium-containing slags or residues guarantee an adequate supply, commensurate with the steady growing demand.The major share of the world's vanadium output is being consumed by the steel industry. As an additive to steel, the versatility of vanadium is particularly impressive. A few hundreds of one per cent of vanadium convert plain carbon steel into high-strength, low-alloy steel with more than double strength. On the other extreme, high-speed steels made via the powder metallurgy route show superior performance with vanadium additions as high as 6 or 8 percent. Vanadium is used as a cost-effective alloying addition in steels for high-temperature service, fully alloyed heat-treatable steels, new dual-phase steels for automotive components, rail steels, etc., to mention only a few applications. Vanadium is also an established essential addition for titanium alloys. The chemical industry is relying on vanadium compounds as important catalysts.In spite of a wide diversity of applications and continual growth in consumption, vanadium has exhibited, over the past several decades, a remarkable price stability, free of conjunctural fluctuations. Because of its availability and versatility, it will continue to be one of the key metallic elements for future technologies.Key Features of VanadiumIn attempting to single out the key features of the metallic element vanadium, three descriptive characteristics come to mind: availability, versatility and price stability."

Jan 1, 1982

By E. H. Jr. Dix

OF all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations had been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 5.25° C. to about 1 per cent. at 300° C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540° C., and that this amount decreases to about 3 per cent. at 20° C.

Jan 2, 1926

By Rospigliosi RT, Krouse HR

The San Vicente stratabound zinc-lead rhythmite deposit, Peru, is hosted in carbonates of the Late Triassic - Early Jurassic Pucara Group. These strata were deposited in a large, shallow water, carbonate platform which extended nearly continuously for 150 kilometers (north-south) in the eastern part of the Pucara basin.The distinctive sulfide-bearing rhythmites occur in three dolomite units which, from bottom to top, include the San Judas horizon with one sulfide-bearing manto; the San Vicente horizon with seven sulfide-bearing mantos including the main ore horizon; and the Alfonso horizon with three sulfide-bearing mantos. The dark gray sulfide-bearing dolostone layers range in thickness from a few millimeters to a few centimeters and contain variable amounts of carbonaceous material, pyrite, quartz, fine-grained sphalerite and galena. They are bordered on each side by selvages of yellow to red-brown coarse-grained sphalerite containing minor amounts of galena. Coarsely crystalline white or gray sparry dolomite is found between the coarse-grained sphalerite layers. Although commonly stratiform and uniform in thickness, the dark layers curve, "pinch out," coalesce, and form "islands" and "peninsulas."Mineral replacement textures, the paragenetic sequence, and presence of sparry dolomite, bitumen, intraformational breccias and isotope data support a hydrothermal replacement origin by metal-bearing solutions that deposited the ore and related minerals in space previously occupied by dolomite and evaporite minerals. The alignment of the Zn -Pb deposits, and at San Vicente the orientation of the mantos, the spatially and temporally associated igneous sills and the tourmaline-bearing sandstone support hydrothermal mineralization driven by a magmatic heat source in a tensional regime.

Jan 1, 1990

By M. E. Wadsworth, J. R. Lewis, J. M. Quets

Samples of snythetic magnetite were reduced in hydrogen at various partial pressures and temperatures. The reaction mas found to be surface controlled and directly proportional to hydrogen partial pressure over the temperature range studied (400° to 1000°C). A transition in the mechanism occurred at approxirnately 590°C. This has been attributed to a change in the slow step of the reduction reaction resulting from the presence of stable wüstite at higher temperatures. Below 590°C the heat of activation for the reduction was found to be 14,700 cal per mole and it was 3,200 cal per mole above 590°C. THE reduction of the oxides of iron has been a subject of study and interest for many years. Edstrom1 has reviewed the work up to 1953 and his findings provide much basic information concerning details of the reduction of hematite (Fe2O3 ) and magnetite (Fe3O4) with both H2 and CO. He concluded that below 600°C the reduction of both hematite and magnetite was essentially identical, since the rate was controlled by a surface reaction at a magnetite gas interface and the iron formed was very porous. The decrease in the reduction rate for both hematite and magnetite immediately above 600°C was attributed to the formation of a stable wüstite phase across which diffusion was very slow. The wide difference in reduction kinetics for hematite and magnetite above 600°C was explained in terms of the character of the wüstite formed. The rate of magnetite reduction increased slowly with temperature beyond the minimum immediately above 600°C and rates equivalent to those observed at 550°C were not obtained until the temperature was increased beyond 850oC. Edstrom and Bitsianes2 studied the solid-state reduction of magnetite, the reaction of which can be written (4x-3)Fe + Fe3O4—4 FexO [1] where x is between 0.83 and 0.95. The rate was found to be controlled by the kinetics of transport of iron ions through the wüstite phase. Bogdandy and Riecke3 studied the kinetics of reduction of small grains of iron oxide in hydrogen and qualitatively attributed the slow step in the reduction process to the diffusion of hydrogen and water vapor through pores. McKewan4 has analysed the data of Joseph,5 Stalhane and Malmburg,6 and Lewis7 and has demonstrated that the kinetics of reduction of both hematite and magnetite are controlled by surface reactions and also that the variation in surface area during reduction must be accounted for. McKewan was able to correlate the reduction data by the equation rodo[1-(1-R)1/3] = Kt [2] where ro is the initial particle radius, do is the density of the iron oxide, R is the fraction reduced at time t, and K is a rate constant. The applicability of Eq. [2] for temperatures above 600°C where a stable wüstite phase is present, indicates the slow step in the over-all kinetics does not result from diffusion unless diffusion occurs laterally along the oxide metal interface or through a wüstite layer of constant thickness. Diffusional control through a layer of wüstite is unlikely, however, in view of the pressure effects demonstrated by Tenenbaum and Joseph,' Diepschlag,9 McKewan,10 and the results of the present study. McKewan has demonstrated a linear rate dependence on the hydrogen partial pressure over the temperature range 400" to 1050°C for the reduction of hematite.

Jan 1, 1961

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed'-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,'~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967

By D. J. Pye

Certain high molecular weight synthetic polymers in very dilute solutions decrease water mobility in porous media 5 to 20 times more than would be expected from the solution viscosity. This indicates that increasing water viscosity to reduce adverse mobility ratios in water floods is economically feasible in many situations. Laboratory results are consistent with accepted theory with respect to improved areal sweep, permeability distribution and displacement efficiencies as would be predicted from the solution mobility measured in the core. The laboratory results have been confirmed by field pilot floods which recovered 80 per cent and 100 per cent more oil than comparative water-flood pilots in fields containing 16 cp and 130 cp oil respectively. Economic analyses based on pilot data indicate the method to be profitable. INTRODUCTION The desirability of improving the water-oil mobility ratio in waterflood-ing operations has long been appreciated, especially for high viscosity crudes. Methods of reducing the oil viscosity by application of heat, gas resaturation and miscible drives have met with some success. Conversely, it has been generally conceded that increasing the water viscosity would also be effective, but the amount of thickening agent required to effect an appreciable increase in viscosity is discouragingly high. The use of such materials as glycerin, sugar, or glycols is completely out of the question economically, so that considerable attention has been given to the use of the much more efficient synthetic water-soluble polymers as viscosity improvers; but even these materials are not economically attractive. If increased water viscosity could be economically realized, marked improvements in areal sweep efficiency, as discussed by Caudle and Wittel and others, would be realized in field operations. Similarly, the improved mobility ratio would bring about increased recoveries by correcting permeability distribution problems as discussed by Stiles2 and Dykstra and Parsons,' and improvements in displacement efficiency would be obtained as recognized by Buckley and Leverett4 and Welge.5 LABORATORY STUDIES THE RESISTANCE EFFECT In the course of research to develop a more efficient water-soluble polymer viscosity builder, we discovered that a very few types of water-soluble polymers exhibited a most unusual and very interesting property not previously observed. Among the earliest materials showing such activity were polymers containing acry-lamide. Fig. 1 shows a typical plot of the solution viscosity vs concentration for one of these polymer solutions as determined in an Ostwald viscometer. As usual, such a plot is an approximate straight line on semi-logarithmic paper. Now, an inspection of Darcy's law, shows that a viscosity value can also be determined in a formation sample if the pressure, flow rate and permeability are known. If the core permeability is previously determined with wa- ter or brine, then the viscosity of another aqueous fluid may be determined from the equation. The viscosities so determined for glycerin (glycol or polyvinyl alcohol solutions, for example) agree with the viscometer determinations. However, in the case of the water-soluble polymer solutions in which we are interested, the viscosities measured in the formation sample depart very markedly from the viscometer values. A typical relationship for a polymer solution is also shown in Fig. 1. This unusual departure from the expected response is referred to as a resistance property of the polymer and is quantified as "resistance factor". Since the resistance factor R can best be determined in a core under study, the term has been defined on the basis of the ratio of the brine mobility to the polymer solution mobility at residual oil saturation so that:

Jan 1, 1965

By P. Dayal, L. S. Darken

THE migration of carbon in austenite under the influence of an electric current has been observed qualitatively several times.14 Lebedev and Guterman5 recently have reported quantitative measurements; their method consisted of welding a low-carbon to a high-carbon wire, passing current, and later estimating the carbon distribution metal-lographically. We believe the method reported in this paper is superior in principle since electrolytic migration and ordinary diffusion are not necessarily coupled as in the weld method; also for the first time the extent of migration is determined by combustion analysis for carbon. A uniform tubular specimen (S.A.E. 1045 or 1095) was mounted as illustrated in the figures. the whole assembly being in an atmosphere of purified nitrogen. Direct current (129 to 226 amp at 0.65 to 1.0 v) served as source both of heat and of potential gradient for carbon migration. The duration of experiment was 7.5 to 12 hr, during which time the temperature was controlled (±10°C) manually. The experimental conditions are indicated in the first five columns of table I. With this experimental arrangement, the temperature initially has a maximum value at the central plane. Also, in this vicinity (by virtue of the symmetry), the carbon entering any volume element is equal in quantity to that leaving; the loss or accumulation of carbon occurs near the electrodes since the carbon moves uniformly near the center and is "frozen" at the cold ends. Hence, providing the time of experiment is not sufficiently long to seriously influence the conditions at the central plane, carbon crosses this plane only under the influence of the electrical potential gradient and not under the influence of temperature or concentration gradient. The amount of carbon which has crossed this plane was determined by combustion analysis of the two halves of the specimen. The results of these analyses are shown in the sixth and seventh columns of table I. It will be noted that substantial amounts of carbon migrated from the anode portion to the cathode portion (except at 920°C, which temperature was too low to exhibit the effect in the allotted time). In spite of precau-tions taken, considerable decarburization occurred as may be seen by comparing cols. 8 and 5. In three cases (indicated by asterisks in table I) the specimen was ground on one side, polished, and examined metallographically before analysis. One specimen was normalized and re-examined. Micrographs of selected areas in specimens 4 and 6 are shown in figs. 1 and 2, respectively. Evidence of carbon migration from the anode toward the cathode is quite apparent. Fig. 2 shows abundant graphite as well as cementite in a region near the cathode. The temperature of this zone is estimated at about 800°C. In fig. 1, particularly in the micrograph on the extreme right (the right side of which is of unaltered carbon content), there is evidence of slight depletion of carbon in the immediate vicinity of the cathode as contrasted to the general increase in carbon of the cathode half of the specimen. Although this may be attributed in part to decarbur-ization, it is believed that it is occasioned also by thermal diffusion—migration (of carbon) from a cool to a hot zone4—a phenomenon superimposed upon the electrical migration. Evidence of carbon migration was visible particu-larly during the course of the high-temperature,

Jan 1, 1951

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1' studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By W. R. Purcell, C. S. Brooks

The internal surfaces of rocks which are in contact with interstitial fluids are known to influence in some degree the recovery of hydrocarbons from pay zones. Despite the admitted importance of the influence of solid surfaces on hydrocarbon recovery, little information is available concerning the extent of surface of reservoir rocks. In this paper a description is given of the apparatus and procedure employed in the determination of the surface areas of sedimentary rocks, and values are reported for a variety of sandstone and limestone cores. In addition, consideration is given to the Kozeny equation, which relates surface area to porosity and permeability. A colliparison is made between the surface areas as calculated from this equation and the geometrical areas of a series of packs of spherical glass beads. Also, for a group of sandstone cores. Kozeny areas are compared with surface areas as determined by the gas adsorption method employed in this investigation. INTRODUCTION It has long been recognized that many processes which are of importance to hydrocarbon production are controlled in some degree by the extent of the surface of the reservoir rock through which the hydrocarbons move. For example, the recovery efficiency that is obtained in a given reservoir is certainly determined in part by the action of interfacial forces between the reservoir fluids and rock, and this action is influenced in turn by the extent of solid surface. Despite the admitted importance of surface effects to problems of petroleum recovery, little information is available concerning the extent of surface of reservoir rocks." It is the purpose of this paper to describe an apparatus which has been employed for the measurement of the surface areas of rock samples and to present the values which have been obtained for a variety of sandstone and limestone cores. In addition, the relationship of surface area to permeability and porosity, as given by the Kozeny equation, will be discussed. METHOD OF MEASURING SURFACE AREA The method of determining surface areas as employed in this work has previously found wide use in studies of porous solids such as catalysts. The method involves the measurement of the amount of physical adsorption of an inert gas, such as nitrogen or argon, on the bare surface of the solid at reduced pressure and constant temperature near the normal liquefaction temperature of the gas. With the aid of the theory of isothermal adsorption as developed by Brunauer, Emmett, and Teller,' it is possible to ascertain the amount of gas (and hence the number of molecules) which is required to cover the solid surface with a single layer of molecules. From a knowledge of the covering area per molecule the total surface ares of the solid can be computed. Since the Brunauer. Emmett, Teller (BET) theory has been adequately discussed elsewhere: it will suffice here merely to present their final equation as ordinarily employed for surface-area calculations. This equation relates the volume of gas, V, which is adsorbed at pressure, P, to the liquefaction pressure, Po, of the gas, and to the volume of gas, V.,, that is required to form a monomolecular layer: In this equation C is a quantity which is related to the heats of adsorption and liquefaction of the gas; for a particular solid-gas system at Constant temperature, C is considered to have a constant value. The basic adsorption data can be presented in the form of Equation (1) by plotting the quantity P/V(Po- P) as a func-

Jan 1, 1952

By Tell Ertl

The term oil shale is defined. Foreign oil-shale developments are outlined briefly. The richest and most extensive oil-shale deposits in the United States lie in western Colorado. The Bureau of Mines is opening two adjacent areas for underground mining. in western Colorado. From the first area the oil shale is mined selectively as required by the retorting plant. The second area is being developed as a unit of a full scale oil-shale mine to ascertain the most practical methods of mining oil shale and to determine costs. In both of these mining areas, research will be carried on to develop new and improved practices for mining oil shale. Introduction Oil shale is a sedimentary rock containing a solid mineraloid of indefinite composition known as kerogen. On heating oil shale, the kerogen undergoes thermal decomposition and some of the vapor products of the decomposition can be condensed as shale oil. Oil from shale can be a major source of liquid fuels since extensive deposits of oil shale are known to exist throughout the world. The United States considers the establishment of an oil-shale industry only when doubt exists of the adequacy of the domestic supply of crude petroleum. On the other hand, oil shale is not strange to foreign oil men. The industry is an old one in other parts of the world. The French industry has been in existence since 1838, the Scottish since 1859, the Australian since 1860, the Estonian and Swedish The since World War 1, and the Manchurian industry since 1929. The most highly exploited oil-shale deposits are the Carboniferous shales of Scotland. About 20 seams ranging from 4 to I2 ft in thickness are worked. The yield during recent years in scotland has been 18 to 25 gal of shale oil per ton, from 3&"30'000 tons per year' The French and Swedish oil-shale deposits are of lower grade than the Scottish. The Estonian oil-shale deposits are 7 ft thick, and the oil yield averages 50 gal per ton. Over 1,000,-ooo tons are mined each year, half of which is used directly as fuel to substitute for coal and the other half is used for the production of oil. Immense deposits of oil shale that will yield 10 to 15 gal per ton exist in Germany. Because of the impending loss of the Rumanian and Polish oil fields and the bombing of synthetic liquid fuel plants, the Nazis in 1943 started a large-scale oil-shale program in Germany. By V-E Day, it is said, oil-shale production had reached the rate of 2500 tons per day and rapid expansion of the industry was imminent. Australian oil shale, known as torbanite, occurs in beds 2 to 6 ft thick. It is of a very high grade and on retorting yields 80 to 160 gal per ton. The oil-shale industry of Manchuria was the largest in the world during the past decade. The well-known Fushun coal deposit in Manchuria has an overburden of 500 million tons of oil shale about 450 ft thick that will yield 10 to 15 gal of shale oil per ton. The oil shale is

Jan 1, 1949

By F. W. Jessen, R. W. Durie

The dissolution of salt in the development of salt cavities is controlled by free-convection boundary layer flow along the salt surfaces. It is the purpose of this paper to expand upon results published previously, and primarily to illustrate the influence of surface features on the boundary layer and hence the dissolution process in the development of underground salt cavities. General dissolution equations are presented that apply to a surface inclined to the vertical. A salt surface inclined so as to be overlain by water is dissolved by boundary layer flow, while an inverted surface is dissolved by a combination of boundary layer and cellular flow. Detailed investigation of the boundary layer was limited to laminar free-convection flow. Truly laminar free-convection boundary layer flow may be encountered only in laboratory solution cavities, but the boundary layer will control dissolution even where cavity dimensions are such that free-convection turbulence will occur. The factors found to significantly affect the laminar boundary layer will affect dissolution with a turbulent boundary layer. INTRODUCTION Underground salt cavities have been used extensively for the storage of LPG products, and the use of these cavities is expanding each year. The increasing requirements for such cavities suggest the need for a better understanding of the mechanisms involved, for the purpose of the control of cavity geometry and the most effective use of the injected water. A previous paper outlined a quantitative approach to the determination of salt dissolution rates in the laminar free-convection dissolution of salt. It is the purpose of this paper to expand upon the results previously published and to point out significant factors in the application of these results to the dissolution of field cavities. The dissolution of salt in laboratory scale cavities is controlled by the free-convection boundary layer, which is the region of flow along the salt surface caused by the difference in buoyancy forces resulting from the salt dissolution. The transfer of salt into solution at the salt face causes an increase in salinity, and hence a greater density, in the water at the salt surface. The region of higher density tends to fall through the lighter, less saline water and a flowing boundary layer is the result. The water remains stationary at the contact with the salt surface,l so the resulting velocity profile is such that the influence of gravity is opposed by a viscous shear force at the salt surface. For salt to be transferred into solution from a solid surface to a boundary layer of fluid, it must diffuse through a stationary film of water at the salt contact. According to Fick's first law, the rate of mass transfer by diffusion is the product of the diffusion coefficient and the concentration gradient, with diffusion transfer in the direction of decreasing salinity. Once the salt has passed into the boundary layer, it will be transferred by a combination of molecular diffusion and convection. The convection transfer will in turn affect the rate of dissolution by influencing the gradient of the salt concentration at the surface. In the previous investigation by the authors to determine the basic mechanism of the salt dissolution process, an equation was developed that agreed very well with the experimental rates of free-convection salt dissolution from a smooth vertical surface. The technique was taken from the work of Eckert2 in the analogous heat transfer system and will be referred to as the integral method. The rate of salt transfer from a vertical section of height H was found to be:

Jan 1, 1965

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967