Search Documents

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

[The following discussion, comprising both remarks made at the Chicago meeting and contributions since forwarded to the Secretary, is based upon the following papers, presented at that meeting : "Segregation and its Consequences in Ingots of Steel and Iron," by Alexandre Pourcel, Paris, France. (See p. 105, mans. xxii.) " Microscopic Metallography," by F. Osmond, Paris, France. (See p. 243, Trans. xxii.) " Microstructure of Ingot-Iron in Cast Ingots," by Prof. A. Martens, Berlin, Germany. (See p. 37.) " Microstructure of Steel," by Albert Sauveur, South Chicago, Ill. (See p. -546, Trans. xxii.) "Farther Observations on the Relations Between the Chemical Constitution and Physical Character of Steel," by William R. Webster, Philadelphia, Pa. (See p. 113.) "The Heat-treatment of Steel," by H. M. Howe, Boston. Mass. (See p. 466.) Since all these papers were considered together, no attempt has been made to separate the discussion strictly under the several heads.] William R. Webster, Philadelphia, Pa.: I desire to say that in my first paper (Trans., xxi., 766) the actual ultimates were subtracted from the estimated ultimates, whereas in the paper submitted at this meeting the estimated ultimates are subtracted from the actual, thus giving contrary signs. The latter method corresponds with the direct effect. of low and high finishing-temperatures ; that is, a plus difference indicates low, and a minus difference high, finishing-temperature. I make this explanation to prevent confusion in comparing the two papers. Mr. Sauveur has shown that there is a close relation between the size of the grain and the ultimate strength, and also that the size of the grain depends on the temperature at which the material is finished in rolling, and on the chemical composition of the steel. I have shown that there is a close relation between the chemical

Jan 1, 1894

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By Jack A. Simon, M. E. Hopkins

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By A. J. Phillips, C. G. Grant, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to supply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their usefu1 life; however, the partial redesign

Jan 1, 1951

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By H. H. Richardson, E. H. Dix

Of all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations would have been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 525" C. to about 1 per cent. at 300" C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540" C., and that this amount decreases to about 3 per cent. at 20" C. In the same year Ohtani and Hemmi3 reported a solubility of 4.8 per cent. copper at 520" C., 2.6 per cent. at 460" C. and 1.5 per cent. at 420" C.

Jan 1, 1926

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

By Alexander L. Field

This paper contains an account of experimental results obtained in an extensive investigation of steels containing zirconium. There recently appeared' an announcement by F. M. Becket, at whose suggestion and under whose general direction this investigation was made, a statement of the outstanding features of the work and a brief explanation of the factors that led to its inception. It is not possible, in a paper of this character, to record all of the operating and test data collected, which includes the production of more than 350 heats of steel. The difficulty of a complete presentation is increased by the fact that several lines of experimentation are too incomplete to warrant publication of the results at the present time. In addition to the methods of manufacture and test employed in the work, there is described experimental evidence on which are based certain definite conclusions regarding the remarkable effects brought about by the presence in steel of relatively small percentages of zirconium. When added to a molten steel bath, zirconium combines chemically with dissolved oxygen, nitrogen, and sulfur, in the order named, and is capable of neutralizing the embrittling effect of phosphorus in whole or in part; although in the case of phosphorus there is no evidence so far of actual chemical combination. These effects arc not in the nature of suppositions supported by theory, nor is their existence deduced merely on the basis of analytical evidence. In each phase of its relation to or reaction with the four impurities mentioned, zirconium affects beneficiauy the mechanical properties of the steel to which it is added, in a manner which it is one of the purposes of this paper to explain in terms of a tentative working theory.

Jan 1, 1923

By D Hodder, M Hoskins, A Rofe

Pasminco Century MineÆs slurry pipeline was commissioned in November 1999. It currently transports zinc and lead concentrate slurries in batch form to the Port facility, 304 km away in the Gulf of Carpentaria. The Pipeline and the Port have gone through several stages of continuous improvement to match the successful ramp-up of the concentrator. Improvements in the Pipeline and Port Operations have included: commissioning of the first slurry pipeline that delivers two products in the same pipeline in batch mode; management of batches throughout the pipeline and port system to minimise cross contamination of both concentrates; operation of the slurry pipeline to achieve high availability of the system; operation of the pump station interfaced with preventive maintenance to minimise unplanned shutdowns; continuous monitoring of pressures throughout the single-station, 304 km slurry pipeline; redesign of the Rotary screw feeder; redesign of the Dryer Control System; installation of a larger Induced Draft Fan; optimisation of the dryer internals to achieve a product of narrow size distribution and pellet integrity; redesign of the stockpile ventilation system; and the development of a surface sealant. This paper describes the early commissioning of both the Port and the Pipeline and the continuous learning and Quality Improvement Project initiated at the Port to focus on concentrate quality given the propensity of the fine concentrate to self-heat during storage.

Jan 1, 2003

By Bob Snashall

Introduction 1300 BC, Egypt. Pharaoh, the god-king, owned all things. He was the only mine operator. As the provider of all things, Pharaoh had great expectations of his officials who gathered the wealth. Pharaoh's official, the mine foreman, was at a gold mine site to see that royal expectations were met. For the official, it could mean a promotion to the good life here and to the godly life hereafter. When he checked the haul for sufficient progress, a lot was at stake. The miner wore a loincloth, perhaps a headband and, if he was a prisoner, ankle manacles. Only an oil lamp helped illuminate the hot, dusty blackness. A fire at the base of the quartz ore face competed for scarce air. The ore so heated crumbled at the prompting of copper wedges. Confined to a crouch, the miner tossed chunks of ore onto a rope-mesh which, when loaded, was drawn up and lugged out. On the surface, the gold was ground to dust. Then it was transported by donkey caravan to the royal depot. There it was weighed, recorded, and distributed to workshops. Many minerals mined Egypt had gold mines to the south in Nubia and to the east in the desert and Sinai. Indeed, gold underwrote Egypt's prosperity. With a constant gold supply, fewer hungry hands robbed burial crypts and tombs. Gold was sacred, "the flesh of the gods." The shiny metal financed the army that policed the desert mining routes and guarded the gold caravans from Bedouin marauders. Gold theft was an offense to the gods. Anyone caught with gold `in his lunchpail,' so to speak, could say goodbye to life, both in this world and the next. In addition to gold, Egypt possessed other mined riches that allowed the Egyptian civilization to flourish. From Sinai and Nubia came copper. So abundant was the red metal that it enabled Egypt to become the supreme power, before the advent of iron. Also mined were amethyst, turquoise, feldspar, jasper, carnelian, and garnet. These were used for the rich inlay work that distinguished Egyptian jewelry and cloisonne. But Egypt's most endurable and awesome material was its stonework - for statues and obelisks and in temples, tombs, and pyramids. Stone quarrying was a vast enterprise. One expedition boasted nearly 10,000 men. These included 5000 laborer soldiers, 130 skilled quarrymen and stonecutters, and - egads! - even 20 scribes. In addition, there were thousands of officials, priests, and officers grooms. There were even fishermen, to provide the multitudes with the catch of the day. Mining methods detailed In 1300 BC, quarrying techniques had changed little since the age of the pyramids some 1300 years before. At that time, in 2600 BC, limestone was locally quarried and fashioned into the blocks of the pyramids. A basic limestone mining method was tunnel quarrying. A ramp was built up to the face of a cliff. A monkey stage was then erected on a ramp. While standing on the stage, quarrymen carved out a rectangular niche in the cliff. The niche was large enough for a quarryman to crawl into. With a wooden mallet, he hammered long copper chisels along the edges of the niche floor to free up the back and sides of the block. The quarryman climbed out of the niche and removed the stage. He then carved out a series of holes in the cliff face for what would be the bottom of the block. The quarryman pounded wooden wedges into the holes. He watered the wedges until they were soaked. The water-logged wedges expanded, splitting the stone along the line of holes. The freed-up block was then levered down from the cliff. On the ground, the blocks were placed on sledges. Men pulled these to nearby water transport. Without block and tackle pulleys, paved roads, and wheels, this was no mean feat. Each block weighed an average of 2.3 t (2.5 st). Whenever possible, the quarrying was done directly from the surface. This "open cast" quarrying also involved using chisels

Jan 2, 1987

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By H. H. Klepfer, M. E. Snyder

UNTIL very recently, the commercial availability of the rare earths as metals has been very limited. Fabrication of mill products from these metals has not been studied in most cases. This note reports the results of the development of fabrication techniques for thulium. Thulium has a melting point of about 1550°C and a hexagonal close-packed crystal structure. It oxidizes in air to give a black oxide (TmzO,). The procedures for producing thin thulium foil were developed on one ingot weighing about 220 g and were subsequently applied in processing about a pound of metal to foil. Several alternates for the various fabrication steps were investigated and will be discussed. The metal fabricated was in the form of commercial chill-cast ingots 1 in. in diam and 2 in. long weighing approximately 220 g. Impurities in the ingots were reported by the vendor to be 4000 ppni tantalum, 2000 ppm calcium, 200 ppm nickel, 100 to 200 ppm iron, 100 ppm europium, and less than 100 ppm copper, lutetium, and ytterbium. In addition to these impurities, several salt-like inclusions as large as l/8 in. in diam were revealed along the center line of the one ingot sectioned. Preliminary tests indicated that small wafers cut from the as-cast ingot would not fabricate readily by rolling. Forging of copper-jacketed wafers was therefore attempted. At 1550"F forging was satisfactory but an apparent reaction of copper with thulium demanded investigation of lower temperatures. Therefore, the remainder of the test ingot was forged at 1450°F—with only minor cracking. All ingots forged were inserted into copper tubes of 1 in. 1D and 0.125-in. wall thickness. The jackets were sealed by flattening the ends of the tubes and welding under helium. Heating time at 1450°F was 30 min. Press forgings of 1/8 in. per pass were used, followed by 10 min reheats. When the ingots had been squared and reduced to 0.250 in. in thickness, the original copper jacket was stripped off and replaced by a new jacket in preparation for hot rolling. Hot rolling at 1450" F without edge cracking was readily accomplished after forging. Excellent results were obtained with 10 pct reductions of thickness followed by 5 to 10 min reheats. After reduction of thickness from 0.250 to 0.100 in. the copper jacket was removed. It was found, in fact, that hot rolling in air was possible. A tenacious black oxide similar to that seen on zirconium was formed during 3 min reheats at 1450°F. Reduction in air to 0.010 in. foil was possible taking 10 pct reductions per pass. The oxide coat formed during hot rolling in air could best be removed by sand blasting and pickling. Common pickling solutions containing polar solvents were found to attack the metal too rapidly and a concentrated nitric-hydrofluoric acid mixture attacked neither the oxide nor the metal. The most satisfactory pickling solution was 52 vol pct concentrated nitric acid-48 vol pct glacial acetic acid. After forging to 0.250 in., vacuum annealing and cold rolling was found to be another satisfactory alternate to hot rolling in copper jackets. After forging. a hardness of Rockwell B76 was found. Annealing in vacuum (2 X l0-5 mm of Hg) for 1 hr at 1200"F did not alter this value. Annealing at 1470"F for 1 hr brought the hardness down to R;]63. With cold rolling (5 pct per pass) the hardness returned to about R,1:76 after 20 pct reduction and edge cracking became noticeable. However, cold rolling to a total of 40 pct reduction in thickness (RI,,83) was possible before edge crack propagation became serious. Good surface finish was obtained, and the metal loss due to oxidation was minimized by cold rolling and vacuum annealing. Using this procedure the yield of 1.25 in. wide by 0.010 in. thick foil from a 1-in. diam ingot was about 40 pct.

Jan 1, 1961

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By J. W. Thompson

ORE CONCENTRATION PROCESS-PATENT OIL FLOTATION PROCESS. The invention of the patent issued to Sullman, Picard & Ballot November 6, 1906 (United States Letters Patent No. 835120), is based upon the discovery of an wholly unexplained phenomenon arising from the agitation of ore pulp containing oil and air in certain proportions. This was a discovery in an art in which it was well known that the elements of oil, air, and agitation possessed certain characteristics and produced certain results. As early as 1860 a British patent first suggested the use of oil in water concentration of ores by pointing out the affinity which oils have for metallic sub- stances in preference to gangue. Subsequently many patentees employed the known affinity of oil for metal in ore concentration proc- esses by using oil in proportions varying from 2 per cent to 300 per cent of the ore and recovering the oil-coated metal particles by causing them to rise to the top or sink to the bottom of the pulp. In these processes the agitation was either gentle or thorough but never great, and though always employed to produce thorough oiling of the metal it was used in different degrees for the sole pur- pose of causing the metal particles to rise or sink. In the prior art the oil was used for its known selective affinity for metal, agitation was em- ployed to mix the oil with the metal, and air was introduced to supple- ment the buoyancy of oil in raising oil-coated metal particles to the surface. To this extent had the art of oil flotation advanced when the patentee entered it, having reached the commercial stage in only two processes, representing respectively metal-flotation and metal-sinking processes, and having reached the stage of success in none. In the line of experiments by the patentee when the proportion of oil to ore was reduced to 1.5 per cent a "float" appeared; at 1.04 per cent still more "float" appeared; at 0.32 per cent the "float" again vastly in- creased; at 0.1 per cent the "float" again vastly increased. It thus developed that in using oil at 0.1 per cent or even at 0.05 per cent of the ore and after violently agitating the pulp from 24 to 10 minutes, there arose to the surface when the pulp was brought to rest, a thick froth or foam of oil-coated air bubbles carrying oil-coated metal particles to the extent of about 90 per cent of the metal con- tent, the foam being sufficiently stable to permit removal and metal recoveries. This was a new result based upon phenomenon then unknown and still unexplained and constituted discovery and promised a change in the art of oil flotation from laboratory experi- ments and mill failures to commercial success. The patent referred to covering the points mentioned has been sustained by the District and the Circuit Courts of Appeals and by the Supreme Court. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, pp. 754-757. ORE CONCENTRATION PROCESS-OIL FLOTATION-INFRINGEMENT. The Miami Copper Co. in its process of concentrating ores by the oil flotation process used three distinct processes that were either the processes included and covered by the Sullman, Picard & Ballot patent or their fair equivalent and which were clearly an infringe- ment of the patent, and the company can not escape liability for such infringement by taking an additional step, although such additional step if taken alone would not constitute an infringement of the Sullman, Picard & Ballot patent. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, p. 768. ORE CONCENTRATION PROCESS-VALIDITY OF GREENWAY PATENT. The patent issued to H. Greenway, June 9, 1914 (Letters Patent No. 1999699), is valid. The process disclosed in this patent was a substantial departure from processes of the prior art. The heating of water is a matter of large moment and the use of acids is a matter of constant and considerable expense. By wholly dispensing with both by the use of a minute quantity of hydroxy compounds, the patentee has disclosed an original and novel plan which has broad- ened and made more simple the agitation process of air flotation. The novelty and inventive character of Greenway's discovery is patentable.

Jan 1, 1918

By R. Maddin, A. Lawley

Single crystal Mo-Re alloys (99.99+ purity), grown by electron bombardment floating zone heating, were deformed in tension at temperatures from -196° to +200°C. At -196oC, Mo-6 pet Re and Mo-20 pct Re alloys deform by slip on systems of the type (101) [1ll]. Above-78oC, the operative slip system is of the type (112) [111], (101) [1ll], or (211) [1ll], depending upon orientation. Mo-39 pct Re alloys deform by twinning and slip at all test temperatures with a (112) [111] type twinning system. Critical resolved shear stress for slip and twinning is calculated as a function of composition and temperature, and the mechanical properties compared with those of less Pure polycrystalline alloys. HEXAGONAL close-packed rhenium, c/a = 1.615, is highly soluble in molybdenum. The bee molybdenum-rich solid solution extends to approximately 42 at. pet Re* at 2500°C,' Fig. 1. Recent work on polycrystalline alloys has shown conclusively that the addition of rhenium to molybdenum improves both the fabricability and the low-temperature ductility.2"5 Similar behavior is observed for W-Re and Cr-Re alloys.5 Initially, Geach and Hughes2 found that the Mo-30 pct Re alloy could be cold rolled to approximately 90 pct reduction before the onset of cracking. The remarkable effect of the rhenium was later confirmed by Jaffee et al. 3-5 with an optimum condition of maximum strength combined with maximum ductility at the Mo-35 pet composition. At higher rhenium contents, the ductility was severely impaired due apparently to the presence of brittle tetragonal s phase, Fig. 1. In the Mo-35 pet Re alloy, at least 110 ppm (parts per million) oxygen could be tolerated before cold workability was reduced. By comparison, the corresponding tolerance figure in unalloyed molybdenum is ~ 10 ppm. The effect of rhenium was considered in terms of: 1) a reduction in oxygen solubility in the lattice; 2) a redistribution of intergranular oxide from grain boundary films to isolated spheres; and 3) the promotion of twinning as a further mode of plastic deformation. Paradoxically, twinning is often associated with brittle fracture in iron and the silicon irons.6'7 Work to date has been restricted to are-melted and powder metallurgy polycrystalline material of ~ 99.9 pet purity. The present investigation was initiated for the purpose of determining the mode and crystallography of plastic deformation of a series of bee Mo-Re alloy single crystals over a wide temperature range from -196o to +200°C. Using high-purity zone-melted material (~ 99.99 + pet purity), the specific role of rhenium in the molybdenum lattice may be understood more fully since effects due to grain boundaries and oxide redistribution will be absent. At the same time, the study provides a comparison of single and polycrystalline deformation behavior. EXPERIMENTAL TECHNIQUES A) Preparation and Purity of Single Crystals. Alloys in the form of either are-cast and swaged or sintered and ground bar, 0.120 in. diam, were obtained from the Chase Brass and Copper Co. Alloy single crystals ~ 8-in. long were grown from the

Jan 1, 1962

By M. Herman, G. J. London

A series of dilute Fe-Co alloy specimens were prepared from zone-melted iron. The iron used was given ten floating-zone passes in purified hydrogen. Alloying was accomplished by plating a gradient of metallic cobalt onto a 1/4-in.-diam bar of material from a pure plating bath. The deposit was radioac-tively tagged by a small addition of co80 to the plating bath. Alloy homogenization was accomplished by passing an additional floating-zone pass through the plated section of the bar. The final concentration gradient achieved was from residual to about 1000 ppm (0.1 pct) added Co. After homogenization, the bar was swaged to 0.057 in. wire and cut to tensile specimen blanks 1-1/16 in. long. Each specimen was counted in a well-type scintillation counter. The concentration of cobalt was computed by combining the normalized specimen counting rate with the known weight (measured to the nearest 0.01 mg) of cobalt added during plating. Fig. 1 shows the cobalt gradient obtained, exclusive of residual cobalt which was estimated by neutron-activation analysis to be approximately 50 ppm. Results of recrystallization for 1 hr at 750°, 700°, 650°, and 600°C with specimens containing 40, 170, 470, and 870 ppm added Co are shown in Figs. 2, 3, 4, and 5. Recrystallization was accomplished in a dynamic vacuum of less than 1 x 10 torr. The specimens were mounted and polished parallel to the swaging direction. The recrystallization re- sults show a radical coarsening of structure with increasing cobalt concentration. The coarsest structure obtained was at the 470-ppm level (at all recrystallization temperatures) with a slight grain refinement at the 870-ppm level shown. A more normal solid-solution effect is seen in Fig. 5 (60OoC, 1 hr) where the only specimen completely recrystallized is the one containing 47 ppm Co. Since the possibility existed that some atmosphere-contamination phenomenon might be responsible for the observed results the recrystallization series was repeated using sealed quartz capsules. These were filled with purified argon which was gettered during heat treatment on metallic titanium included in the capsules. The results obtained were essentially the same as shown. Another identical alloy was made using a 5-mm-diam bar of Westinghouse Puron. Specimen preparation and recrystallization treatment were also as described. The results obtained (see Table I) were somewhat erratic. Some coarsening in structure does appear at the highest cobalt concentrations. There is no apparent relationship between the coarse, columnar, directionally solidified structure of the as-melted bars and any of the recrystallized grain structures observed, all of which are much finer than the former structure. A recrystallization process can be most simply described as one of homogeneous nucleation of recrystallized grains in a cold-worked matrix followed by more or less uniform growth of the strain free grain into the cold-worked material.' An impurity element may influence one or both of these processes. Aust and utter' have shown that impurities strongly influence grain boundary mobility in lead. Moreover, definite recrystallization textures are produced by small concentrations of tin,3 while additions of silver or gold4 produce large boundary in-

Jan 1, 1964