Search Documents

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By D Cliff

Despite advances in technology, the Australian underground coal mining industry continues to have incidents involving spontaneous combustion. Managing these incidents relies heavily on understanding the state of the event as it develops and controls are applied. Gas analysis plays a major role in aiding this interpretation. This interpretation is based upon laboratory testing of coal samples under conditions very different to those found in an underground coal mine. This paper will explore the links between laboratory data and actual events. It will highlight the difficulties of using laboratory data. It will outline the relevance of laboratory data and how it can be usefully applied to manage spontaneous combustion events as well as in establishing relevant trigger action response plans to facilitate early detection and control of such events. The paper will identify some of the factors that need to be applied when adapting laboratory data to apply to the underground coal mine. It will outline the need for comprehensive knowledge of the local conditions and gas concentrations to be expected at all locations in an underground coal mine. Further, it will demonstrate the need for mine environment monitoring to go beyond simply measuring gas concentrations but also to include reliable atmospheric pressure, temperature and air velocity monitoring.CITATION:Cliff, D, 2013. Gas analysis - Linking the laboratory with reality, in Proceedings The Australian Mine Ventilation Conference , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By K. W. Morris

Of the fossil fuels used for power generation coal is by far the most variable and complex in its properties. A thorough review of the characteristics of the coal to be fired is essential before boiler design can begin. Major parameters such as heating value, moisture content and ash properties will determine not only the boiler size and configuration, but also the performance of the unit with respect to the thermal efficiency, particulate and gaseous emissions, and unit availability and reliability. An example of a review completed on a large low-rank coal deposit for a power plant will be described.

Jan 1, 1983

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

pNumerical modelling has been used to examine the relationship between the results of two commonly used methods of assessing the propensity of coal to spontaneous combustion, the R70 and Relative Ignition Temperature tests, and the likely behaviour in situ. The criticality of various parameters has been examined and a method of utilising critical self-heating parameters has been developed. This study shows that on their own, the laboratory test results do not provide a reliable guide to in situ behaviour but can be used in combination to considerably increase the ability to predict spontaneous combustion behaviour./p

Jan 1, 2005

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By James J. Anthony

High-angle in-pit conveying is an idea that is being seriously studied by a number of important mining companies in North America. Its application in coal, iron ore, and copper mining is expected to reduce mine operating costs considerably compared with the conventional discontinuous methods, such as truck haulage, which are fuel, labor, and maintenance intensive. Therefore, a mine introducing high-angle in-pit conveyors will gain a competitive advantage over mines which continue to use conventional haulage. While the capital outlay for in-pit conveyor systems obviously varies depending on pit depth, the angle of incline, and the capacity required, it generally will not exceed that of truck haulage when all Factors are taken into consideration. These factors include the cost of excavation, as measured in relation to the volume of minerals mined, the cost of building truck ramps and roads, and the capital outlay for the trucks and maintenance facilities. In many cases, in Fact, the capital outlay will be less than for truck haulage. This cost advantage will best be realized by new mines, whereas in existing producing mines the switch from truck haulage may involve the abandonment of a substantial capital asset.

Jan 1, 1983

By Paul A. Glapa

Quality is much more than providing a product that functions properly. True quality is a way of thinking, a way of doing business, and, ultimately, a way of satisfying a customer?s long-term needs. A true commitment to quality requires a top-down management commitment, with a willingness to change what needs to be changed and to expand upon ?best practices? that are already done well. Is there a cost to creating and maintaining a quality program? Of course there is, but the cost of not having a focused program is much greater. We have come to regard quality as an investment that pays dividends to both the supplier and customer. The lack of quality costs everyone and the customer pays the ultimate penalty. With modern, highly engineered surface mining equipment the end user calculates cost in terms of lost production (revenue), not simply the cost of the part. Bucyrus International, Inc. is a company that has listened to its customers and has dedicated itself to implementing an advanced quality program. The ultimate goal being the creation of a high quality product with extended reliability for the customer. The result is reflected in Bucyrus? current product offerings and highlighted by the new 495HF electric rope shovels at Albian Sands mine.

May 1, 2003

By John P. Coughlin

The Bureau of fines has tested a portable microseismic processor recorder at the Galena Mine, Wallace, ID, both in an environmentally controlled enclosure and, with minimal protection, in a working area of the mine. In both trials the device demonstrated effective and reliable data acquisition capabilities.

Jan 1, 1985

By John L. Hostetler

GALFAN, the Zn-5% Al-mischmetal hot-dip galvanizing alloy is coated onto steel sheet, wire, and tube using high-speed continuous galvanizing lines. Factors critical to producing high quality GALFAN are reviewed, The relationship between minimum mischmetal content in the GALFAN alloy and furnace dewpoint will be described. The relationship between peak annealing temperature and furnace dewpoint will also be shown. Typical suategies for operating multi-purpose hot-dip galvanizing lines including GALFAN will be described. A recent development has allowed preparation of steel smp for GALFAN coating using aqueous fluxes rather than high temperature annealing. This allows production of GALFAN-coated smp without over-ageing of the steel, and allows high steel strengths and hardnesses to be obtained. The principles of this process will be described.

Jan 1, 1992

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an exten- sion of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, how- ever, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's pro- duction facilities are maintaining a satisfactory quality control.

Oct 1, 1965

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By T. R. Kostecki, J. Hirschi

"Analytical engineering design is based upon a trial-and-error iterative and deterministic process. Within this process, the engineer obtains some estimated values, plugs them into de facto closed-form equations, and receives output, which is expected to be a single number that serves as the basis for the design. This number is typically a factor of safety, or some other equivalent strength-stress ratio. This provides the engineer with a quick and relatively quantitative design methodology. This can create problems however, because in mining applications, the actual in situ system is highly variable, complex and often chaotic, which can lead to potentially incorrect conclusions that result in unsafe designs. A more appropriate and reliable approach is a probabilistic analysis for engineering design. This process is used widely in civil and other engineering disciplines, but is often overlooked for applications in coal mine design. Additionally, it seems the amount of past studies using this approach, especially in coal mine design, are rather limited. Considering how the probabilistic approach can account for uncertainty in parametric values and how unpredictable a mining design can be, the authors believe that this approach has potential in mining. This paper will focus on a summary of past studies related to probabilistic analysis in coal mine pillar design and provide recommendations for future work that could improve design reliability. INTRODUCTIONFeasibility and fundamental design procedures for excavations often start with an assessment of mine openings, pillar design, and the surrounding structure by using a deterministic approach with closedform solutions (ex. Bienawski, Obert-Duvall). These are reliable methods, but designers know that the inputs in these closed-form solutions are estimates at best and do not incorporate any degree of uncertainty. This is therefore not an optimal design procedure.A more appropriate design should incorporate some uncertainty because of the chaotic and variable nature of geology and mining conditions in general. In an attempt to account for uncertainty, a probabilistic approach can be adopted, which accounts for deviations in variables and provides a more optimum design solution. By applying a probabilistic approach, a designer can look at multiple failure scenarios at the same time instead of using the same deterministic design over and over."

Jan 1, 2015

By F. G. Schwartz

This circular presents the results of a survey of research on jet fuel thermal stability jointly sponsored by the National Petroleum Refiners Association (NPRA), Tulsa, Okla., and the Bureau of Mines. The development of supersonic planes has led to many problems that did not exist in the operation of subsonic aircraft. One of the most important of these is rapid deterioration of the fuel at the high temperatures to which it is subjected. At higher speeds, aerodynamic heating of the airframe imposes severe thermal problems, and conventional techniques of rejecting the heat to the atmosphere become impractical. The fuel is the only material present in sufficient bulk to be used as a heat sink. Thus, the fuel is subjected to aerodynamic heating and also is used to dissipate heat from lubricating oil, hydraulic fluid, electronic equipment, wheel wells, and cabin air. Consequently, the fuels may have to withstand both moderate temperatures for sustained periods in the fuel tanks and higher temperatures for brief periods during transfer from the tanks to the combustion chamber. Because of high temperatures, insoluble residue or gum may form in the fuel and contribute to heat exchanger fouling and to clogging of the fuel manifolds, nozzles, control systems, and other components of the fuel system.

Jan 1, 1962

By Elaine Ellingham, Francis T. Manns

"Abstract -The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at0.156 oz/TAu . The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distribution s, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

Discussion of the paper of R. J. COLONY, presented at the New York Meeting, February, 1921, and issued With MINING AND METALLURGY No. 169, January, 1921. R. J. COLONY (author's reply to discussion).-The work of Sosman and Merwin on the system lime-ferric oxide, mentioned by Mr. Rankin, was not overlooked. When studying portland cements and portland-cement clinkers petrographically, however, the lime-iron compound was difficult to correlate with the very definite dicalcium ferrite described by those investigators, which possesses such well-defined optical properties. In portland cements, the calcium ferrite (or ferrate?) is an indefinite, fuzzy, and generally amorphous, or apparently amorphous substance that is distributed interstitially with respect to the other grains, from which it was very difficult to derive any satisfactory results. For this reason, the writer, tentatively, chose to regard it as related to the aluminate, and assigned to it the composition 3CaO.Fe203, which may be incorrect, however, as Mr. Rankin suggests.

Jan 8, 1921

By A. Deneys

This paper reviews industrial gases used in primary copper production. Copper smelting industrial gas demand has steadily increased since the first commercial oxygenconcentrate smelting in 1952 [1]. In copper production oxygen for smelting is the dominant industrial gas use followed by oxygen for converting. Nitrogen is finding increased use in copper smelters. Nitrogen is used for porous plugs for copper converting and anode refining [2-5]. Nitrogen can be used for concentrate drying [6,7] and is also used in some Ni-Cu smelters as a coolant in Peirce-Smith converting [8,9]. Industrial gas supply options of cryogenic or adsorbent based on-site plant or cryogenic liquid delivery are detailed.

Jan 1, 2007