Search Documents

By D. M. Waldorf

Steam permeability measurements have been made in the laboratory on several samples of natural reservoir materials. The steam temperatures and pressures were selected to simulate conditions which might exist in a reservoir during the injection of steam. For each sample tested, the experimental permeability to superheated steam was comparable to that measured with air and no evidence of plugging was detected. Some samples were exposed to water at various temperatures and plugging was found to occur in materials which contained significant quantities of monmorillonite clay. Temperature had little effect on the degree of plug-ning between 75 and 325 F. The measured pemeabilities tended to increase slightly with temperature, but the changes were small compared with the initial loss of per~neability on wetting. Sequential pemzeability measurements were made on two samples using air, water, steam, water and air, in that order. Both samples were water-sensitive and plugged extensively after the initial injection of water. Upon exposure to superheated steatm the samples dehydrated and their permenbilities to superheated steam were comparable to those initially measured with air. The remaining measuretnetzts with water and air confirmed that the water plugging was reversible and that the samples were not seriorrsly damaged during the tests. INTRODUCTION The swelling of water-sensitive clays during water floods has long been recognized as a potential source of reservoir damage. The recent extensive application of steam injection and stimulation has compounded this problem since both hot water and steam (as well as fresh water at reservoir temperatures) are, at sume time, in contact with the producing zone adjacent to the bore of a steam injection well. The purpose of this paper is to present data which compare the sensitivity of some natural sedimentary rock samples to water at various temperatures, and to super-heated steam. Some properties of montmorillonite clay are briefly reviewed, and comparisons are drawn between empirical data and the predicted behavior of the montmorillonite known to be present in the samples. PROPERTIES OF MONTMORILLONIT E CLAY Water initially adsorbs on dry N a -montmorillonite clay in discrete layers in the interlaminar space between clal platelets. The platelet spacing, which is 9.6 A (angstroms) for a dehydrated clay, has been observed to expand in discrete steps to 12.4, 15.5, 18.4 and 21.4 A spacings, indicating the formation of four discrete layers of regularly oriented water molecules.' The first two layers are easily formed by hydrating a dry sample to equilibrium in an atmosphere with carefully controlled humidity. The formation of the higher layers is more difficult. The usual X-ray diffraction patterns of the more highly hydrated samples indicate a gradual increase in the average spacing betwcen 15.5 and 19.2 A, followed by a discontinuous expansion to 31 A when the weight ratio of water to dry clay is between 0.5 and 1.2.' Platelet expansion above 31 A proceeds monotonically as the moisture is increased and no regular arrangement of the platelets ib observed. Water-sensitivity in sedimentary rocks is usually associated with Na-montmorillonite clay when it is in the noncrystal-line state. Mering3 found that the average lattice spacing of sodium montmorillonite hydrated at 68 F and 70 per cent relative humidity was 15.5 A, and that the spacing, at 92 per cent humidity was 16.5 A. The water adsorbed at the higher humidity has the same free energy as liquid water at 65.6 F. Kolaian and Low' used a tensiometer to measure the thermodynamic properties of water in diffuse suspensions of montmorillonite clays relative to pure water. They observed that water in suspensions as dilute as 6 per cent clay became partially oriented when left undisturbed. The bonding associated with this orientation was not extensive because the free energy difference between the water in suspension and pure water was only a few millicalories per mole. They also found that the measured free energy difference decreased rapidly with temperature and became negligible above 100 F. This evidence indicates that montmorillonites contained in sedimentary rocks would dehydrate to a crystalline structure when exposed to superheated steam, and that the rock permeability measured with steam would be equivalent to that measured with air. The effect of elevated temperatures on the swelline of montmorillonite clays in aqueous suspensions has not been investigated. The Gouy-Chapman diffuse-ion-layer theory has been used to predict the swelling pressure of clay suspensions in dilute salt solutions at room temperature with reasonable success. theory also correctly predicts the direction of the thermal response of Na-mont-morillonite swelling pressures in dilute salt suspensions, 9 Over the temperature range of 33 to 68 F, an increase in

Jan 1, 1966

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By S. Luszcz, R. W. Vook, Fred Witt

In situ X-ray investigations were made on polycrys-talline silver films deposited by vacuum evaporation on (111) CaF2 and (100) NaCl single-crystal substrates at 80°K. The films were evaporated and annealed in an X-ray diffractometer attachment having a residual gas pressure of 2 x lo-' Torr. All measurements were made without exposing the films to the atmosphere. Measurements were made on the films in the as-deposited state and after various annealing treatments. The intrinsic stacking and twin fault densities, the magnitudes of the uniform and nonuniform strains, and the crystallite sizes were determined. In addition the textures in the films were measured qualitatively. The results obtained for the as-deposited films on single-crystal substrates are in substantial agreement with previously reported results for silver films deposited on glass. Intrinsic stacking and twin faults, as well as uniform and nonuniform strains, were present in these films. During the various annealing treatments (up to 350°C) the faults and nonuniform strains annealed out. Considerable grain growth and texture changes occurred also. The effects were much greater for the NaCl substrate than for the CaFz substrate. The relative magnitudes of the grain growth in the variously oriented grains could be explained qualitatively in terms of the thermal strains and strain energies introduced into the differently oriented grains during the initial, irreversible anneal. These strains were due to the different thermal expansion coefficients of the film and substrate. X-RAY diffraction measurements on evaporated films deposited on substrates at low temperature have the advantage that many of the imperfections introduced into the film during deposition are "frozen in". Thus, the influence of a very important experimental variable, substrate temperature, on the imperfection structure of evaporated metal films may be studied. Moreover, the effects of annealing such films makes possible the study of thermally activated recovery processes in these films. The present study was designed to determine the influence of single-crystal substrates on the resultant film structure relative to the previous results obtained using glass substrates.' To this end great care was taken to keep the experimental variables the same in the two cases. Different experimental conditions would, of course, result in films having different physical properties. Again the initial substrate temperature was in the neighborhood of 80°K and the films were subsequently annealed to 350°C. The pure metal silver was chosen for evaporation, primarily because of its relatively low stacking fault energy and consequent high fault density in the as-deposited state. The silver films were formed by evaporation onto air-cleaved {ill} CaF, and (100) NaCl surfaces cooled to 80°K in an X-ray diffractometer attachment2 having a base residual gas pressure of 2 X l0-' Torr. The films were not exposed to the atmosphere until all of the X-ray data had been recorded. In this way one of the most important experimental variables, environment, could be well-controlled and reproduced. X-ray measurements were made at the temperature of deposition and included determinations of the diffraction line peak positions, line shapes, and integrated intensities. The peak position measurements were used to determine the intrinsic stacking fault densities and the average uniform strain in the film. The shapes of the diffraction lines provided information on the twin fault density, true crystallite size, and average nonuniform strain. The preferred orientation in the film was determined qualitatively from the integrated intensities. I) EXPERIMENTAL PROCEDURE The evaporator attachmentZ was charged with 99.999 pct Ag pellets positioned in a tantalum filament which had been outgassed previously at l0-8 Torr. The CaFz and NaCl single crystals were cleaved in air and then placed in position in the chamber so that their cleavage surfaces were on the diffractometer axis. The chamber was prepumped using a sorption pump, sealed off, and then baked at 150°C for 24 hr. The ion pump operated during the bakeout cycle. The substrate was then heated to 500° C by means of an auxiliary heater and kept hot until the rest of the chamber was cooled slowly to room temperature. This bakeout procedure consistently resulted in an ultimate pressure in the low lo-' Torr range. The substrate was then cooled down on 80°K. Its temperature was monitored by a thermocouple wedged into the rear of the copper substrate holder. The diffracted intensity and peak position of the 111, 222, and 333 CaF, lines were measured prior to evaporation. Nickel-filtered, pulse-height-discriminated copper radiation was used. Similar measurements were made for the 200 and 400 lines from NaC1. These measurements were used as a lattice parameter check and to determine the thickness of the evaporated silver films from the attenuation of the substrate lines. The evaporation rates were approximately 3A per sec for both films while the maximum pressures during evaporation were 3 x lo- ' and 7 x 10"8 Torr for the CaF, and NaCl cases, respectively. The film thickness was measured by the attenuation of the CaF, and NaCl substrate lines and by at optical interference method. Values of 1700 and 1500A, respectively, were obtained for the silver

Jan 1, 1969

By A. Raman, P. P. Singh

The constitution of the La-Rh system was studied by powder X-ray diffraction, metallopaphic, and differential thermal analysis techniques and an equilibrium diagram is presented. Eleven intermediate phases occur in the system and the crystal structural data for nine of them were determined. La3Rh crystallizes in an orthorhombic structure of undetermined type, whose unit cell is obtained by doubling the 'a; and 'c,,' edges of an FesC type unit cell. The other intermediate phases of the system are LarRh-3( undetermined structures also occur in the system. LaRh, undergoes a polymorphic phase transformation at 1240°C. LaRh3 and La2Rh7 also exhibit polymorphisnz. The phases Laah and LazRh7 melt congruently. The latter undergoes a eutectoid transformation into LaRh, and Rh at 1205°C. Laah3 is formed by a peritectoid reaction between Laah and La,Rh,,. The other Phases result from peritectic reactions between the liquid and the adjacent rhodium-rich phases. The intermediate Phases of the La-Rh system are compared with those of the La-Co and La-Ni systems. DURING the course of a detailed investigation to study the occurrence of CrB, FeB, A1B2, and related structures in the rare earth alloys it was found that much information is lacking for the rare earth noble metal systems. Although the structures of several rare earth alloys containing the noble metals at the AB and AB2 stoichiometries have been reported, the occurrence of related structures at other stoichiometries has not been studied. We have initiated a project to study the crystal structural features of selected rare earth-rhodium alloys and to map the equilibrium diagrams of representative systems with conventional methods. The results of our investigation in the La-Rh system are presented in this paper. Two phases were known in the La-Rh system. LaRh has the CrB-type structure.' LaRhz is a MgCu2-type Laves phase.z EXPERIMENTAL PROCEDURE Alloys weighing less than 1 g were prepared from commercially pure lanthanum (99.9 pct +), supplied by Lunex Company, Pleasant Valley, Iowa, and rhodium (99.92 pct +), supplied by Engelhardt Industries, Newark, N.J., in a conventional arc melting furnace under argon atmosphere. The buttons were turned upside down and remelted three times to insure homogeneity in the samples. Since negligible loss of material was encountered during melting, a chemical analysis of the alloy buttons was not undertaken. Powder specimens for X-ray diffraction studies in the as cast state were then prepared. The buttons were wrapped in thin molybdenum foils and homogenized by heating in vacuum at suitable high temperatures for more than 1 week. They were then broken into three or four pieces for annealing experiments. The pieces were wrapped in molybdenum foils and annealed at various temperatures in evacuated quartz capsules. The annealing was carried out for 2 hr at or above 1200°C, 1 day at temperatures close to llOO°C, 2 days at 1000°C, and for 1 week at temperatures below 1000°C. After annealing the alloy pieces were again broken and powder specimens for X-ray diffraction were prepared. The powders of the lanthanum rich alloys with more than 80 at. pct La were prepared by filing. The filings were sealed in molybdenum tubings and stress-relieved at 600°C in vacuum. It was not deemed necessary to stress-relieve the powders of the other alloys, since the alloys were very brittle and were ground easily. POWDER X-RAY DIFFRACTION X-ray diffraction photographs of powders (-325 mesh size) of the alloys in the as cast and annealed states were prepared in a Guinier-de Wolff focussing camera with copper K, X radiations. These patterns were studied to identify the stoichiometries and the crystal structures of the intermediate phases. The lattice parameters of the phases were calculated after minimizing the differences between the observed sin2 6 values, calculated from the diffraction angles 8, and the sin2 8 values, calculated using approximate lattice constants obtained from a few lines. These differences were minimized manually to less than 0.0005. The latLice constants are judged to be accurate to *0.005A for values less thp about 10A and to k0.01~ for values greater than 10A. The relative intensities of the lines were calculated using a computer program written by Jeitschko and Parthk.~ No attempt was made to refine the atomic positional parameters in the phases. METALLOGRAPHY The phase equilibria in the investigated alloys in the as cast and annealed states were also studied by metallographic examination. The polished specimen surfaces were etched with 10 pct picric acid in alcohol (alloys up to 25 pct Rh), concentrated picric acid (from 25 to 37.5 pct Rh), 2 pct nital (40 to 50 pct Rh), 10 pct nital (from 50 to 66.7 pct Rh) and with concentrated 48 pct HF for the other rhodium-rich alloys. Selected microstruture~ were then photographed using a Po-laroid Land camera. THERMAL ANALYSIS Differential thermal analysis of the alloys was carried out in DTA-668 Stone differential thermal ana-

Jan 1, 1970

By R. A. Graham, R. W. Rohde

The effect of hydrostatic pressure upon the austenite start temperature of a commercial Fe-28.4 at. pct Ni-0.5 at. pct C alloy has been determined. For pressures to 20 kbar, the austenite start temperature decreased from its atmospheric pressure value of 380°C at the rate of about 4°C per kbar. These data are analyzed by two different thermodynamic approaches; first, considering the transformation as an isothermal process, and second, considering the transformation as an isentropic process. It was found that both these approaches fit the experimental data equally well. The effect of hydrostatic pressure upon the austenite start temperature is best described by considering the mechanical work done during the transformation as that work obtained by multiplying the applied pressure with the gross volume change of the transformation. It is widely recognized1 that strain has an important effect on the initiation of martensitic transformations.* For example, the martensite start tempera- *In this paper, use of the term martensitic transformation implies the reversal of martensite to austenite as wen as the formation of martensite from austenite. ture, M,, may be increased by plastic deformation. Similarly, plastic deformation is observed to lower the austenite start temperature, A,. The effect of uniaxial stress on the M, of iron-nickel alloys has been studied by Kulin, Cohen, and Averbach.2 They found that the martensite start temperature was significantly changed by stresses well within the elastic region. Moreover, the effect of tensile and compres-sive stresses differed. These effects were explained in terms of the interaction of the applied stress with both the dilational and shear components of the transformation strain. The magnitudes of the influence of uniaxial tension, compression and hydrostatic pressure on Ms were measured in 30 pct Ni 70 pct Fe by Pate1 and Cohen.3 Their thermodynamic calculations and similar calculations by Fisher and Turnbull4 predicted the experimental results when the transformation was assumed to occur isothermally at some fixed driving force. This driving force was assumed to be supplied by a combination of the chemical free energy difference between the austenitic and martensitic phases and the work performed during transformation by the applied stress. More recently, Russell and winchel15 reported the effect of rapidly applied shear stress on the reversal of martensite to austenite in iron-nickel-carbon alloys. They performed a thermodynamic analysis of this transformation based upon the assumption that the re- versal occurred adiabatically. They concluded that the applied shear stress did not significantly interact with the transformation strain and thus did not assist in inducing the reversal. Rather they concluded that the reversal was effected by localized strain heating which resulted from the gross local shear deformation of the experiment. In either the adiabatic or isothermal analysis it is necessary to compute the work performed by the interaction of the applied stress and the transformation strains. In the case of hydrostatic pressure this interaction has been treated by two different methods. In either case the applied pressure is assumed to remain constant during the transformation. In one treatment the applied pressure is assumed to interact directly with the dilatational strain associated with the formation of an individual martensite plate.3'4 This local strain has been measured at atmospheric pressure in iron-nickel alloys by Machlin and Cohen.6 In the above treatment this local strain is assumed invariant with temperature and pressure changes. In the other treatment the applied pressure is assumed to interact with the gross volume change of the transformation.7,8 The usefulness of this latter treatment has been demonstrated by Kaufman, Leyenaar, and Harvey7 who calculated the effects of pressure upon the martensite and austenite start temperatures of Fe-10 at. pct Ni and Fe-25 at. pct Ni alloys. Excellent agreement was obtained between their calculations and their experimental data on an Fe-9.5 at. pct Ni alloy. However, this treatment suffers from the fact that the data required to calculate the volume change of the transformation (i.e., the initial specific volumes, the thermal expansion and compressibility data for both the austenitic and martensitic phases) is, in general, not available for any material except pure iron. Thus the calculations of Kaufman et al.7 were necessarily performed by assuming that the volume change of the martensitic transformation in the iron-nickel alloys was that same volume change occurring during the a-? transformation in pure iron. While this approximation may suffice for very dilute alloys it is likely to be inaccurate in high nickel alloys. We have performed measurements of the effect of hydrostatic pressure to 20 kbar on the A, temperature of an Fe-28.4 at. pct Ni-0.5 at. pct C alloy. The composition is similar to the alloy used by Pate1 and Cohen3 to determine the effect of pressure upon the M, temperature. The present measurements permit calculation of the interaction between the applied pressure and the transformation strain. Additionally, measurements have been made which allow precise determination of the gross volume change of the transformation. The data allow direct comparison between the alternate hypotheses of the interaction between the applied pressure and a dilatational transformation strain characterized by either the formation

Jan 1, 1970

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By D. P. Pope, T. Vreeland

Observations of dislocations in zinc using Berg-Barrett X-ray micrography confirm the validity of a dislocation etch for (1010) surfaces. A technique for measurement of the depth in which dislocations can be imaged in X-ray micrographs is given. This depth on (0001) surfaces of zinc was found to be 2.5 µ using a (1013) reflection and CoKa radiation. BUCHANAN and Reed-Hill (B & RH) have recently questioned the ability of a dislocation etch to reveal all of the basal dislocations which intersect (1010) surfaces in annealed zinc crystals.&apos; This etch was developed by Brandt, Adams, and Vreeland who conducted a number of different experiments to check its ability to reveal dislocations.2,3 B & RH prepared (0001) foil specimens for transmission electron microscopy from annealed crystals and observed dislocation densities of about l08 cm per cu cm in the foils, while the etch indicated densities of the order of l04 cm per cu cm in their annealed crystals. As this etch has been used in a number of studies of dislocations in zinc, it is of considerable importance to reassess its validity in the light of the B & RH results. The X-ray work reported here was undertaken to check the ability of the etch to reveal dislocation intersections on (1070) surfaces of zinc. The X-ray technique was chosen for this check because it could be applied to the as-grown crystals with a relatively small amount of specimen preparation. We believe that the possibility of accidental deformation in preparation of the bulk specimens is considerably less than that for thin foil specimens suitable for transmission electron microscopy. Unfortunately, basal dislocations are not visible on Berg-Barrett topo-graphs of (1010) surfaces, which are the surfaces on which the etch is most effective. Therefore, a one-to-one correspondence between the etch and X-ray observations could not be made. Basal dislocations near (0001) surfaces have been observed by Schultz and Armstrong4 using the Berg-Barrett technique, but they did not report the as-grown dislocation density observed in their crystals. We have applied the X-ray technique in this study to surfaces oriented from 1 to 2 deg of the (0001) to determine the basal dislocation density, and have compared this density with that observed using the etch on a (1070) plane of the same crystal. The X-ray observations permit determination of the depth in which basal dislocations can be observed under the diffracting conditions used. SPECIMEN PREPARATION High purity zinc crystals are very soft, so a good deal of care must be exercised in the preparation of observation surfaces. As-grown crystals approximately 2.5 cm in diam and 20 cm long were acid cut into 1.25 cm cubes. A thin slab was cleaved from an (0001) surface to produce an accurately oriented reference surface on the specimen. Some of the cubes were examined in the as-machined condition while some were annealed in argon at 410°C for 2 hr. Heating and cooling rates were less than 2°C per min. Some of the specimens were scratched on a (0001) surface with a razor blade to produce fresh dislocations. Approximately 2 mm of material was acid lapped from one face of a cube to produce a surface oriented between 1 and 2 deg from the basal plane and parallel to the [1210] direction. A (1070) surface was also acid lapped. The lap used a 1 to 3 pct solution of HN03 in water to saturate a soft cloth which was backed by a stainless steel plate. The cloth was moved over the crystal surface at a rate of 20 cm per sec while a normal force of about 4 g was maintained between the cloth and the specimen. As-lapped surfaces were examined as were surfaces which were chemically and electrolytically polished after lapping. The small angle between a lapped surface and the (0001) plane was measured to 0.1 deg using a Unitron microgoniometer microscope (the cleaved surface was used as a reference in this measurement). The microscope was modified so that the intensity of reflected light could be continuously monitored on a meter. This modification produced nearly a ten-fold increase in the reproduceability of orientation readings. OBSERVATIONS The Unitron Microgoniometer observations indicated that the lapped surfaces had a terraced structure with the terraces quite rounded and spaced about 0.1 mm in the [1010] direction. The maximum change in slope between terraces was 0.25 deg, indicating a terrace height of about 0.1 µ. A Unitron measurement of the average angle between (0001) and a lapped surface was checked by micrometer measurement of the specimen and found to agree within 0.1 deg. The Berg-Barrett micrographs using (1013) reflections and CoKa radiation5 revealed subboundaries, short dislocation segments, spirals, and loops near the surfaces which were oriented from 1 to 2 deg of the (0001). Micrographs of surfaces prepared by lapping appeared very similar to those of the chemically and electrolytically polished surfaces. The loops and spirals were not extinct in (1013) or (0002) reflections, indicating that they have a nonbasal Burgers vector. Extinctions of the short, straight dislocations indicated that they belonged to an (0001)(1210) system. Fig. 1 is an example of a micrograph which shows a subboundary, and dislocation segments which are pre-

Jan 1, 1970

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th&apos;rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling&apos; in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

The geologist is often called upon to give judgment on the possibilities of reviving a former mining field presumably worked out as far as the evidence then available indicated. From time to time, scarcity and consequent high prices of metals has led to there-examination of many old fields. The possibility of resuming investigation on them where the practical miner ceased work, even where he had the aid of the trained geologist, has long since disappeared.Means of access to mines have been removed and water fills the workings. Hence an indirect mode of attack becomes essential.This method depends mainly on past history, and may be described as a reaching out by faith supported by shrewd guessing from the known to the unknown. Apart from whatever general intelligent observations may be made in situ of the evidence of former mining activity, the method depends largely on the examination of the past history of the field as revealed in the official records, company reports, plans of underground workings, local newspaper accounts, and the testimony of practical miners formerly employedon the field, the&apos; reliability of which has to be carefully sifted. The matter derived from the examination of these sources must next be rigorously collated and correlated where possible. When the review of all individu!1l features and aspects has been completed, tentative and speculative conclusions may be drawn which, though not verifiable before the event, will usually prove to be more serviceable guides in exploratory operations than mere &quot;blind stabbing.&quot;As an actual illustration of what is involved in the mode of procedure outlined above, the following is the description of an investigation in which the writer took part.In 1937, during the course of the Commonwealth Aerial, Geological and Geophysical Survey of Northern Australia, a detailed geological investigation was undertaken of the Croydon gold field, situated near the south-eastern. extremity of the Gulf of Carpentaria in North Queensland.The history of the field briefly is as follows: It was discovered in 1885, reached its peak of production 1896, declining thereafter till 1906, when operations ceased. The total production was about 1,000,000 ounces of gold bullion, containing approximately 40 per cent. of silver. The gold bullion was won from flat-dipping quartz reefs, which yielded an average of 2.oz. to the ton, and the maximum depth to which production occurred was 500 feet. Subsequent prospecting below this depth failed to locate further ore.In consequence of the inaccessibility of the mines and the almost total masking of the&apos; surface by alluvium, the investigation of future possibilities became largely an. office ,study, which was conducted under the following headings:-1. Recording of factual data of each mine separately.

Jan 1, 1950

By G. G. Goble

Dynamic pile testing is now over 20 years old as a routinely applied tool for evaluating driven pile installation. The first test on a cast-in-place pile was performed more that 15 years ago. The research that produced the method began almost 30 years ago. But, questions still arise regarding the appropriate use of this technique so some review is useful. Today a number of methods including dynamic testing all depending in some way on the application of dynamics are in routine use. First, Wave Equation analysis can be used to predict pile driveability before going to the field. The same approach can be used during driving to estimate the bearing capacity based on the blow count observed in the field. Dynamic measurements, on the other hand, can only be used after pile driving has begun. They offer predictions of pile capacity as well as measurements of hammer, driving system, and pile driving performance characteristics. The first part of this paper will be devoted to discussing how the foundation engineer can use these tools. First, a brief review of what dynamic methods actually do. In Wave Equation analysis a numerical model of the hammer, driving system, pile, and the soil is created by the engineer. The hammer is dropped on the pile and using a discrete, dynamic analysis the motion of the individual pile elements is calculated as a function of time. Of course, input information must be supplied by the program user to describe the hammer, driving system, pile, and soil. In the current state of development, the primary problem in input data is with the hammer performance (efficiency) and the soil description. Research may be able to do a better job with the soil data, but hammer performance will always vary from hammer to hammer and is dependent on the affectiveness of the inspection process. Prior to beginning pile driving the Wave Equation analysis supplies the best available estimate of what will happen when driving begins. It gives an estimate of blow count during driving, driving stresses, both tension and compression in the pile, and for diesel hammers, stroke. The selection of the driving system can be checked with the results of Wave Equation analysis and modifications can be made if required. For example, if the blow count at the required capacity was deemed excessive by the contractor a larger hammer could be tried or if driving stresses were too high changes could be made in the cushion or the hammer selection could be modified. All of these modifications are possible with only the cost of a computer run. The primary questions regarding the accuracy and reliability of Wave Equation analysis at this time is with regard to the assumptions made to represent the soil characteristics and the difficulty in predicting hammer performance.

Jan 1, 1993

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By O. F. Walker, W. C. Hahn, V. A. Johnson, J. D. Wood

The diffusion coefficients of zinc in single-crystal zinc and carbon in single-crystal and poly crystalline nickel were measured by means of radioactive tracer techniques both with and without the application of ultrasonic vibrations under conditions such that the temperature of the sample was closely controlled. The results of this investigation indicate no enhancement of diffusion in any of the samples. It is suggested that previously reported enhancement may have been due either solely to temperature increases caused by ultrasonic vibrations or in combination with changes in the boundary conditions. A number of observations have been reported in the literature in which it has been implied or inferred that the application of ultrasonics enhances diffusion (see, for example, Refs. 1-5). The present study was undertaken in an attempt to observe this effect under carefully controlled conditions, particularly with regard to measurement and control of the temperature of the sample. Two different types of systems were studied; these were the self-diffusion of zinc and the diffusion of carbon in nickel. EXPERIMENTAL For diffusion with ultrasonic energy applied, the samples were included as part of a resonant ultrasonic system operating at 58.5 kcps. The ultrasonic generators used were rated at 100 and 250 w and could be tuned over a frequency from 10 to 100 kc. A PZT (lead titanate/lead zirconate) ceramic transducer provided the driving vibration. This system requires no metallurgical joining of the specimen to the acoustical transmission line since the ultrasonic driver and the follow-up section clamp the specimen in position by means of a constant pressure of 50 lb developed by an air cylinder. The ultrasonic driver and follow-up section, both made of titanium, were 4 in. in length from clamping point to the end in contact with the specimen. Using the relationship given by Mason,6 A = V/f, the resonant wavelength, A, in titanium is calculated to be 3.3 in. at a frequency, f, of 58.5 kc, taking the velocity of sound in titanium, V, as 1.95 X 105 in. per sec. The 4-in. driver and follow-up section, therefore, are each 4.0/3.3 =1.21 times the resonant wavelength. Clamping pressure must be applied at stress nodes of the transmission line in order to preserve resonance. Therefore, a specimen length of 0.58 times the wavelength in the specimen was required to place the clamping pressure application points at stress nodes exactly three wavelengths apart. A stress antinode was contained in the center 3 in. of the specimen. A small PZT ceramic disc attached to the follow-up section provided an output voltage proportional to the intensity of the standing wave. This output voltage was monitored on an oscilloscope and the ultrasonic system was tuned to resonance by varying the frequency until the output signal was a maximum amplitude. The amplitude of the output signal was maintained constant throughout the diffusion anneal. A split cylindrical stainless-steel chamber, which was purged with argon prior to and during the runs, was placed around the specimen. The chamber in turn was surrounded by a movable furnace whose temperature could be controlled to 7C. Heat exchangers were used to cool the driver, follow-up section, and ultrasonic transducer. Great care was taken to obtain the true specimen temperature in all cases. Several different methods were tried; the most successful was that in which the thermocouple was held in contact with the midlength of the specimen by means of an asbestos insulating pad and wire straps. In the case of zinc, single-crystal specimens of 99.999 pct purity were used. The samples were 0.25 by 0.25 in. square and of the proper length for resonance, that is 1.1 in. long with the c axis parallel to the long dimension of the specimen for the case of diffusion perpendicular to the c axis and ultrasonic motion parallel to the c axis, and 1.9 in. long with the c axis perpendicular to the long dimension of the specimen for the case of diffusion parallel to the c axis and ultrasonic motion perpendicular to the c axis. In each case, one of the rectangular faces was electroplated with a thin film of zinc containing Zn The constant pressure used to clamp the specimen in place in the ultrasonic system caused some deformation in some of the samples. For these samples the deformation was concentrated in either end of the specimen; thus, for all samples (both zinc and nickel) the center in. was cut from the specimen after the diffusion anneal to be used for sectioning and counting. The nickel single-crystal samples, of 99.999 pct purity, were used in the form of rods 0.25 by 0.187 by 2.07 in. long with the (100) direction parallel to the rod axis. The polycrystalline nickel samples of 99.97 pct purity had an average grain diameter of 0.007 in. and were used in the form of rods 0.25 by 0.125 by 1.87 in. long. The direction of ultrasonic motion was parallel to (100) direction (bar axis) for the single-cqstal samples and parallel to the bar axis for the polycrystalline specimens. A thin film of c14 suspended in methanol was applied to the diffusing face of the specimen. Two specimens were butted together lengthwise for each diffusion anneal to minimize oxidation. After diffusion, a precision lapping device similar to the one described by Goldstein7 and a radiation detector were used to obtain a plot of specific activity vs penetration distance for each specimen. (A scintil-

Jan 1, 1969

By W. G. Pfann

A simple method of obtaining multistage batch separations by crystallization was described recently. Known as zone-refining, it comprises passing short molten zones through a long solid charge. This technique can now be used on a continuous basis by means of the zone-void method described in this paper. Feed enters, at an intermediate point, a column down which molten zones travel, and waste and product leave at the ends. Materials move in the column through the agency of voids, which are introduced at the ends and travel toward the feed inlet. The voids and molten zones are moved by external heaters in a simple manner, and the principle of reflux is utilized. ANEW method of obtaining multistage separations by crystallization was described recently.&apos; Named zone-refinina.,-, the method comwrises slowly passing a series of molten zones through a long solid charge. Solute becomes concentrated at one or the other end of the charge, depending on whether it raises or lowers the freezing point of the solvent. The separation increases with the number, P, of zone-passes, approaching a limit as P approaches infinity. Zone-refining has been highly effective in purifying germanium and other substances.2,3 and new applications are steadily increasing. Zone-refining is a batch method and as such it has certain limitations inherent in batch operation. If it could be made continuous, its scope and utility would be greatly broadened. This end has been achieved by the zone-void method described in this paper. In the zone-void method feed is introduced continuously at an intermediate point in a column down which molten zones travel, while impure waste and purified product leave at the ends. Both the flows of feed, waste and product, and also the travels of the zones, are actuated by external moving heaters in a simple manner; and the system utilizes the principle of reflux. The method provides, in the field of crystallization, the counterpart of the continuous fractiona-tion column in the field of distillation. The following will be discussed: apparatus and mode of operation, fundamental nature of the separation, design theory, and practical considerations. The method will be described in terms of a binary solute-solvent system in which the solute is an impurity to be removed and the solvent is the desired product. The distribution coefficient, k, defined as the ratio of solute concentration in the solid freezing out of a molten zone to that in the liquid in the zone, is assumed to be constant and less than one. The process is equally effective for k&apos;s greater than one and for ternary or higher order systems. Method and Apparatus The essential features of a continuous zone-refining process are represented in highly generalized form in Fig. 1. A series of molten zones, produced by moving heaters, travels slowly down the column or charge (to the left in Fig. 1). If there were no flows of feed, waste, or product, the process would simply be batch zone-refining, the action of the molten zones being to sweep solute down the column, solvent up the column. For the process to be con- tinuous, with stripping and enriching sections in the column, feed must enter, and waste and product must leave, as indicated. The zone-void process accomplishes both objectives, namely, the indicated movements of zones and the indicated flows of material. Zones are moved by moving heaters, just as in batch zone-refining. Materials are made to flow by creating voids at the waste and product exits and causing these voids to move to the feed inlet. Since there must be a net flow of material from the feed inlet to each of the outlets, the indicated movements of voids are in the desired directions, because movement of a void in a given direction corresponds to flow of material in an opposite direction. In order to produce the desired movements of voids, the column is folded into two vertical sections having the feed inlet in common at their upper ends. Voids are displaced upward by the liquids in the molten zones and their travel is actuated by the motions of the zones. Voids travel with the zones in the enriching section and move continuously. Voids travel opposite to the zones in the stripping section and move intermittently. Creation and travel of voids will now be examined in detail. The enriching section of a column in operation, with its void generator, is shown in Fig. 2. The column section is a vertical tube around which a series of closely fitting, regularly spaced heaters travel slowly upward. Each heater produces a molten region, the temperatures of the heaters and the cooling between heaters being controlled so as to maintain the molten zones approximately constant in size. A void is normally present atop the molten zone in each heater. As the heater rises, it continuously melts solid above it, which drips through the void into the molten zone and continuously freezes out solid below it, of concentration k times that of the liquid in the zone. When a molten zone and void reach the feed inlet, which is kept molten, the void is displaced by an equal volume of feed liquid. Generation of voids of controlled size in the enriching section is shown in Fig. 3. The void generator is a tube of small cross-section, provided with lateral heat-conducting fins which sense the position of the heater. Liquid can escape only when the entire outlet tube is within the heater. If any part of the outlet tube is outside the heater, liquid cannot escape,

Jan 1, 1956

By William Lyman

GENERAL DESCRIPTION Shrinkage or shrinkage stoping refers to any mining method in which broken ore is temporarily retained in the stope to provide a working platform and/or to offer temporary support to the stope walls during active mining. Since ore "swells" when broken, it is necessary to shrink the muck pile a corresponding amount by draw¬ing some of the broken ore out as the stope is advanced-hence the name. Broken ore retained during stoping is drawn out after the stope has reached its limits. The stope may be left empty or may be filled with waste contemporaneous with, or subsequent to, the final draw. Traditionally the method implies conventional overhand stoping methods with miners working between the muck pile and the stope back, in a space which advances updip with mining and is maintained by balanc¬ing "swell" with "shrink." The shrinkage classification is also applicable to so-called "semishrinkage" methods in open pillar-supported stopes where broken ore is temporarily retained as a working platform but offers no wall support; and to various blasthole shrinkage methods which utilize broken ore temporarily retained in the stope for wall support, but which do not require miners to work from muck pile in the stope. The method is generally applied to steeply dipping veins of strong ore between strong walls. APPLICATION Geometry The geometry of a shrinkable vein is described in terms of dip, width, and regularity along dip. Overall strike and dip dimensions and irregularities along the strike generally impose no restrictions on the method. Dip is ideally 1.2 to 1.5 rad (70 to 90°). As dip falls below 1.2 rad (70°), the shrinkage draw begins to strongly favor the hanging wall side, thus leaving a poor working platform for conventional overhand work. This is particularly true in relatively wide stopes. The sup¬port afforded to the hanging wall also diminishes with decreasing dip, reaching nil as the dip approaches the repose angle of broken ore. Dips below 0.78 to 0.87 rad (45 to 50°) are not generally shrinkable except by open stope "seinishrinkage" methods. Minimum mining width is fixed by working space requirements in the stope-generally about 1 m. Shrink¬age in narrower veins requires that waste rock from one or both walls be broken with the ore and the attendant dilution accepted to achieve the minimum width. Nar¬row stopes are less suitable, encouraging hang-ups and bridging of broken ore, with the attendant problems of erratic draw and incomplete recovery of broken ore. Maximum practical width may be 3 m or less to over 30 m, depending upon the competency of the ore and its ability to stand unsupported across the stope back. This is a vital safety consideration in conventional over¬hand stopes, but is much less of a factor in blasthole shrinkage methods. Very wide veins and massive ore bodies have been mined by transverse vertical shrinkage panels separated by transverse vertical pillars which are either abandoned or recovered later by other methods. Regularity along the dip is a prerequisite of shrink¬age as there must be no serious obstruction to the flow of broken ore downward through the stope to the sill level. Gentle rolls along the dip are acceptable if the local footwall dip everywhere exceeds 0.78 to 0.87 rad (45 to 50°). Off-dip hanging wall and/or footwall splits can generally be mined selectively from a conventional shrink stope as they are encountered without ad¬versely affecting subsequent continuation of shrinkage mining updip on the main vein. Vertical offsets or major rolls along the dip which cannot be "smoothed over" generally require that a sublevel be established with new draw control development. Blasthole shrinkage methods are much less flexible (and thus less selective) in their ability to accommodate any of these irregularities. Ground Conditions The wall rock must be strong enough to stand with the minimal support afforded by the dynamic mass of broken ore in the stope. During active mining, local sloughing from the walls is restrained, but the broken ore affords little, if any, useful resistance to closure of the stope walls. Such squeezing, if present, may bind up the stope and cause the loss of much ore. Pillars left between and/or within stopes are effective in preventing closure but reduce overall recovery. Walls may be re¬inforced by bolting after each stope cut in conventional shrinkage but not in blasthole shrinkage. Ore in place must be strong enough to stand with no natural support across the stope width, although tem¬porary artificial support or reinforcement may be used locally in conventional stopes. Some spalling or sloughing is permissible in blasthole shrinkage as men are never present in the stope. Physical and/or mineralogical characteristics of the broken ore may impose restrictions on stope design and/or operational plan¬ning, and may even preclude the use of shrinkage al¬together. Examples include: ores which, when broken, are cohesive or which tend to pack or cement together under the influence of ground water, wall pressure, and/ or chemical reaction. Such conditions precipitate er¬ratic draw during mining and often result in difficult and/or incomplete final draw; pyritic ores which oxidize very rapidly in the stopes and may generate heat, imposing a fire hazard by spontaneous combustion; sulfide ores which oxidize sufficiently in the stopes to adversely affect mill recovery by flotation; and ores (es¬pecially those containing uranium minerals) which ex¬ude radon gas and thereby impose ventilation constraints on stope design. In most cases these problems can be minimized by limiting the size of stopes, by minimizing the duration of mining activity in each stope, and by promptly drawing each stope empty following comple¬tion of mining.

Jan 1, 1982

By E. B. Mayo

David LeCount Evans (Consulting Petroleum and Mining Geologist, Wichita, Kans.)-—Not only E. B. Mayo but also W. C. Lacy, who apparently urged the preparation of this analysis, is to be commended. Regional thinking of this type is needed to assure future success in the never-ending search for new mineralized and petroliferous districts. As is usually the case, here is a regional study that will be read by the mining geologist alone. It is ironic that several of the trends established in this study have suggested themselves in northern mid-continent, detailed, and regional studies. These, where established, have offered new keys to petroleum exploration and have provided a possible basis for unraveling a number of broad generalities. The oil geologists, active in Colorado, Kansas, and Oklahoma, would find much food for thought in Mr. Mayo&apos;s projections. To be more specific: 1) The parallelism between E. B. Mayo&apos;s Texas Lineament and the Amarillo Uplift, the Wichita Complex and the Arbuckle Complex of the Texas Panhandle and Southern Oklahoma is viewed with interest and appears especially significant when compared with the similar northwest trend of the Central Kansas Uplift, a major trend of production. 2) Considering the various northeast zones of Fig. 2, and with particular reference to Mayo&apos;s C-C, the Jemez Zone is on direct line with one of several northeast-southwest controls which the present writer has been using with some success in Kansas subsurface correlations. Considering zones of shearing, with no apparent vertical displacement, but suggesting strike-slip movement, because of the staggered effect on other features which cross such trends, Mayo&apos;s philosophy presents regional possibilities for lines of weakness, considered to this time of only local significance. 3) And, finally, in an area as distant from the Southwest as central Kansas, the north-south trends of the Fiarport-Ruggles anticline, the Voshel-Hol-low Nikkel-Burrton structures, the Dayton to Stut-gart trend, the north, slightly east trend of the Ne-maha structural complex, and others all seem to approach the north-south alignments, a through f, of Mayo&apos;s Fig. 3. Mayo&apos;s employment of structural intersections to pinpoint crustal weakness, to localize igneous activity and its accompanying mineralization is not, perhaps, a new concept, but it is a 1958 model, produced by tools improved from the ever-increasing accumulation of geological observations. The use of intersecting trends in petroleum geology is not a new idea, since much production in earlier days was encountered via the straight line projections of established trends to centers of intersection. A tragedy in this age of specialization is that iron curtains have been raised between groups, all seeking raw materials, all acolytes at the altar of structural geology, but all smugly content in and protected by the ivory towers of petroleum geology, engineering geology, mining geology, and geophysics. Mayo presents basic ideas which can stimulate mid-continent structural thinking and, in the case of cen- tral Kansas. he provides a key to replace the broad and overworked simple monoclinal, sinkhole-dotted, Karst topography credo, which is not finding its share of new oil in a state where the declining discovery ratio is disconcerting. The American Association of Petroleum Geologists would do well to add E. B. Mayo to its list of Distinguished Lecturers. Evans B. Mayo (author&apos;s reply)—In reply to David LeCount Evans&apos; comments, it is pleasing to learn that some of the elements discussed in my paper may interest petroleum geologists as well as mining geologists. This should not be surprising, however, because the lineaments make up the framework of the continent, and the oil-bearing sediments must reflect to varying degrees adjustments of basement blocks along their boundaries. A further possibility that petroleum geologists must have considered is that the slow escape of heat from buried lineaments and their intersections has aided the separation of oil from the sediments and started the migration into traps. Regarding the specific points listed by Evans, the following are suggested: 1) The branch of Texas Lineament marked 1&apos; (Fig. 3) is thought to extend eastward through the Capitan Mts., New Mexico, through the long Tertiary dikes east of Roswell, and beyond via the Matador and Electra ranges of the Red River Uplift, Texas. Its further continuation might be the eastern flank of the Ouachita Fold Belt. The Amarillo-Wichita-Arbuckle zone of uplifts appears to continue east-southeastward the Spanish Peaks belt (3-5, Fig. 3). The northwest-trending Central Kansas Uplift would not belong to the above set, except insofar as the Central Kansas Uplift is traversed by west-northwest folds, possible continuations of the Uinta belt (5-5, Fig. 3). 2) The possible continuations into Kansas of the Jemez zone are new to me and are most welcome suggestions. 3) Most of the nearly north-south Kansan structures mentioned by Evans are unfamiliar to me, but the Nemaha Uplift itself appears to be part of a very pronounced structure traceable from the Cerralvo Fault Zone, south of the Rio Grande, through the Bend Arch, Texas, and the Nemaha Uplift, into the Pre-Cambrian of Minnesota (?). This nearly meridional zone is crossed and broken by the Rio Grande Embayment and by the Red River-Wichita Syntaxis. Petroleum geologists realize the economic importance of these features. Perhaps it is inevitable that some papers of general interest be buried in the journals of specialized groups. Moreover, papers dealing with regional, or lineament, tectonics and its applications to exploration for economic mineral deposits are as yet few in the American literature. The opportunity to advance this field is open to all those who are not ultra-conservative and who have a lively curiosity, plenty of patience, and not too many business restrictions. In conclusion, much appreciation is extended to D. L. Evans for his comments.

Jan 1, 1960

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan&apos;s theory,&apos; the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler&apos; undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen&apos;s rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the&apos; extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen&apos;s rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen&apos;s rule also holds in this case. Whenever Matthiessen&apos;s rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan&apos;s theory,&apos; as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen&apos;s rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956