Search Documents

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By Louis D. Murino

Compared to coal or many metals industries, talc must be considered a small, specialty market catering to niches and dependent primarily on the physical attributes of the mined and processed mineral rather than the chemical attributes with copper, lead or uranium concentrate, the primary objective is the percent metal that ultimately is refined by the smelter, as opposed to the brightness, particle size distribution, trace impurities or morphology. The latter constitute the important determinants of where, how and why talc and similar industrial minerals are used. This paper addresses the talc market-place: where it is, how much of a market there is, who the producers are, available capacity, market growth, and marketing techniques.

Jan 1, 1984

By Richard M. Tinlin

The mining industry needs to assure compliance with the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500). Congress has enacted this legislation with the intent of preventing, reducing, and eliminating pollution of the nation' s surface and groundwaters. Recognized sources of pollution such as seepage from tailings ponds, waste dumps, and contaminated effluent from mine dewatering operations pose a serious threat to adjacent groundwaters. In addition, technological innovations being implemented by the industry such as in situ leaching of low grade ore deposits may also lead to ground- water contamination. An adequate monitoring methodology designed to meet the needs of the mining industry is needed. Monitoring and control methodology devised for other man- caused sources of ground- water pollution - e. g., landfills - offer considerable promise for adaptation to the problem. The prediction of deleterious effects on groundwater quality usually requires extensive geohydrological data in addition to a thorough analysis of the mining activity that is underway or projected. If the avail- able data are adequate, mathematical models of surface and groundwater flow can be constructed that will help to predict effects on water quality. Data are inadequate to allow a realistic interpretation of pollution potentials. These data can be supplemented by computer simulation as a method to explore a number of possible environmental effects and also to develop a minimum-cost approach to identifying and gathering the additional necessary supporting data. Incorrect assessment of the important environmental considerations may, in many instances, prove to be the weakest link in analyzing the financial feasibility of a mining operation.

Jan 1, 1973

By L. L. Tavlarides, N. V. Deorkar

"Recovery/Recycling of metal ions from industrial process waste streams is a preferred alternative to disposal by conventional techniques. This paper presents methods for preparation of inorganic chemically active adsorbents to be used in fixed bed adsorbers. Methods for immobilization of chelating agents on the inorganic supports are discussed. The prepared adsorbents are characterized to determine coverage density of functional groups, effect of pH on metal ion removal efficiency, regeneration efficiency and uptake capacity. Results from the laboratory scale and bench scale experiments are presented here.IntroductionRemoval of heavy metal ions from processing wastes in various industries is an important problem. Waste streams in electroplating, electronic, catalyst preparation and hydrometallurgical industries contain metal ions such as copper, nickel, chromium, lead, tin, cadmium, silver, gold and platinum. One major concern for the non-ferrous metal industry is secondary recovery of precious metals and cyanide from cyanide leachate from smelter residue and hydrometallurgical waste streams.Recovery methods recently considered include evaporation, electrolyte metal recovery, reverse osmosis (1), adsorption, ion exchange (2,3), membrane separation (4,5) and Solvent extraction. These processes have met with various levels of limited success. The use of liquid ion exchange molecules to selectively extract metal ions for on-site treatment of these waste streams is currently receiving substantial interest (6,7). This interest seems from an awareness of the advances made in the development of commercial extractants for metal ion separation in hydrometallurgical industries (8). However, separation by solvent extraction processes is generally considered to be economical in the range of aqueous metal ion concentrations from 0.01 to 1.0 mol/lit (9). In order to exploit the selectivity of chelating agents, the idea of immobilizing chelating agent into a solid matrix has attracted growing attention in recent years. Many supports such as inorganic oxides, organic polymers, cellulose powder and polyurethane foam can be used for immobilization of chelating agents. Over the last decade, considerable efforts have been directed toward attachment/introduction of chelating agents into a polymer matrix (10,11). Inorganic supports as compared to polymer supports provide high mechanical strength, chemical and thermal stability, and high reaction rates due to open pore structure. On the contrary, organic resins shrink and swell, thus affecting mass transfer (12). Many of the disadvantages of polymer supports can be excluded by the use of inorganic supports. Innovative use of immobilization techniques can produce inorganic chemically active adsorbents with comparable capacity, stability and reaction rates. Consequently, the objective of our program is the development of inorganic chemically active adsorbents to be used in a fixed-bed unit operation as an alternative heavy metal ion recovery process. Methods of preparation of inorganic chemically active adsorbents, (ICAAs) characterization and applications are discussed in this paper. A brief summary of the results from laboratory scale studies and bench scale studies is presented."

Jan 1, 1996

By John W. Finch

The Secretary of the Interior acting through the Bureau of Mines and the Geological Survey is authorized by the Strategic Materials (Public No. 117 - 76th Cong., Chapter 190 1st Sess.) to make investigation concerning essential minerals of which the quantities or grades obtainable from known domestic sources are inadequate. The Bureau of Mines, in carrying out its part of this program, may investigate deposits of such minerals in whatever manner may be necessary, in order to determine (1) the extent and quality of the are, (2) the most suitable method of mining and beneficiating it, and (3) the cost at which it may be produced. The essential objective in doing these things is to determine where and how supplies of minerals and metals of which domestic production is usually inadequate might be obtained in a national emergency, even though at higher cost than usual.

Jan 1, 1939

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By A. W. Ambrose

"Introduction.Oil-field operations have often been carried on under great stress and haste, in which the prime purpose has been to put the wells down rapidly as possible, without regard to a few of the various factors affecting cost. In such fields as Burkurnett, Texas, where the well locations are town lots and other small tracts, the operator was concerned primarily with in drilling. In such cases a few thousand dollars more or less in the cost of a well not considered. We are reaching a time, however, when our reserves a,more definitely outlined and properties are being along more economic lines. Operators are becoming more concerned with the actual cost of this work, and are gradually learning that fuel consumption can be reduced in drilling and producing without delaying the speed of drilling, and in the case of production, it will greatly reduce the unit cost per barrel of production.Types of Field Boilers.In the oil fields there are in general two types of boilers; those which are used for drilling wells and are of a more or less portable character, and those established later in a more permanent form and serve for the purpose,of generating steam for producing the oil. As a rule, the latter type of boilers are larger than those of the drilling type. Usually, little care is given to the installation of drilling boilers; particularly in attempting to set them up in such a way as to avoid waste in of fuel. Because of the temporary nature of these installations there may be some justification for not giving them more,attention in this resend, but it is believed that a few precautions could be taken that would amply repay the cost and trouble taken. In connection with the boiler plants that are afterwards established, when a few producing wells have been,brought in with a life of two to ten years and probably longer, much care to the boiler-plant construction and to the installation of recording instruments which will assist in operating the plant at minimum cost."

Nov 1, 1920

By Howard G. Coopersmith

A resource of low grade good quality diamonds has been discovered through the Diamond Company NL-Moonstone Diamond Corp. Joint Venture. A limited bulk sample diamond test of two large kimberlite pipes on the Kelsey Lake Property, Colorado, has been completed. These kimberlite pipes have petrological and mineralogical indications of the presence of diamond. Small diamonds were recovered from surface samples. Drilling and trenching revealed both pipes were complexes of diatreme facies kimberlite. One pipe contains crater facies kimberlite as well. This is the first reported occurrence of crater facies kimberlite in the Province. Approximately 1000 tonnes of kimberlite rock was excavated and processed through a scrubber -HMS -Sortex -Grease Plant. Significant diamonds were recovered. The diamonds were generally of good color and clarity, with many being in the gem and near gem categories. Grades are considered low however. Additionally, a small potential resource of alluvial diamonds is present.

Jan 1, 1991

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011

By Clark R. Neuharth

To assess the supply status of ultra-high-purity silicon for national defense needs, the U.S. Bureau of Mines conducted a general study of the availability of materials and processing technology for silicon used in the manufacture of infrared (IR) detectors from raw materials to the highly advanced device state. The United States possesses all of the raw materials and processing technology for IR detector-grade silicon production, but does not produce at all of the processing stages on a regular basis. Consequently, the United States continues to rely on foreign sources for some of these critical materials.

Jan 1, 1989

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

By Z. Yang, M. J. Collins, N. E. Tuffrey, R. J. Kalanchey, I. M. Masters

The high elevation of China Western Mining Company (WMC)' s Ganhe refinery, and the high iron content of concentrates produced by the WMC mines, were key factors in the selection of pressure leaching by WMC for their new zinc refinery. This paper describes the results of pressure leaching test work conducted by Sherritt in Fort Saskatchewan with a sample of WMC concentrate from Qinghai Province in China. Results from batch pressure leach tests and a four-day pilot plant campaign are reported. The pilot plant campaign included continuous operation of a two-stage pressure leach circuit, as well as neutralization and iron removal steps, resulting in the production of iron-free zinc sulphate solution. Greater than 98% zinc extraction was achieved in pressure leaching, while producing solution containing about 9 g/L H2SO4 and 2 g/L Fe. Following neutralization and iron removal, the solution contained about 170 g/L Zn and less than 10 mg/L Fe. Overall recovery of sulphur in the zinc concentrate feed to elemental sulphur byproduct was about 85%, while 75 to 80% of the indium in the feed was recoverable from the neutralization residue. The test results highlighted the technical and economic advantages offered by the Sherritt Zinc Pressure Leach Process and provided the required data for the engineering design.

Jan 1, 2008

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001