Search Documents

By Jamal Rostami, Mark Board, Clayr Alexander, Muthu Vinayak Thyagarajan

In the past several decades, many major equipment manufacturers have ventured into developing new technology for underground hard rock excavation. This includes variety of configurations for full and partial face mobile excavation units. Mining industry prefers machines that can excavate noncircular, flat invert profiles and be able to make tight turns in hard rock. The need to use disc cutters for cutting hard rock has impeded the development of such machines due to the need for gripper system or large mass of a machine to support the force requirements of the disc cutters. Most of the prior attempts have been partially successful and the operations have faced some practical limits and challenges. Among the units that have been successfully used, one can name mobile miner, which was used for rock excavation in some projects. A redesigned mobile miner, called the “Remote Vein Miner,” or RVM, has been developed by Epiroc for underground hard rock mining in Hecla’s Lucky Friday Mine. This equipment potentially opens numerous opportunities for innovation in civil tunneling projects, where the operational flexibility and accessibility of a TBM’s limited tunnel path, design of the profile, and cost are limiting factors. This paper explores the application of the RVM in tunneling projects, its advantages and possible areas of innovation in tunnel planning and design.

Jun 13, 2021

By S. H. Ash

IN no part of the world other than a small area in Pennsylvania is anthracite mining an industry of major magnitude. As the deposits of anthracite in the United States are limited virtually to Pennsylvania, the difficulties of this industry have been commonly considered a state rather than a national problem. However, there is also national interest in the conservation and wise utilization of all the country's fuel resources and in the control of interstate waterways. The anthracite industry is confronted with a serious problem of water accumulation in many of the mines, a problem that must be solved in the near future if progressively higher mining costs are to be avoided. It cannot be solved by the operating companies without state or Federal aid, or both, owing to the magnitude of the work required, the diversity of interests of the coal and surface ownerships, the hazard to the whole mining community, and interests affected outside the mining region. 'The costs of abating the ever-increasing surface seepage to mine workings and of handling this seepage once it has occurred are beyond the eco¬nomic resources of the operating managements.

Jan 1, 1941

By Elisa Araujo Santos Darsie

A busca na melhoria da qualidade dos aços, principalmente no caso de aços limpos, fez com que o distribuidor de lingotamento continuo também seja empregado para a remoção das inclusões responsáveis por prejudicar as propriedades mecânicas dos aços. Uma melhor eficiência desta função do distribuidor pode ser atingida com o conhecimento das características do escoamento do banho metálico de modo que se possam propor modificações na configuração do distribuidor. Esses fenômenos de escoamento e remoção de inclusões podem ser simulados mediante a utilização da modelagem física. O objetivo deste trabalho é avaliar quatro configurações internas de distribuidor por meio da qualificação do escoamento via ensaio de linhas de fluxo e quantificação de inclusões passantes pelo veio com o ensaio de remoção de inclusões. As variáveis de controle utilizadas neste estudo são: velocidade de lingotamento, presença de barreiras e presença de tubo longo. Os resultados apresentados para o distribuidor em questão mostram que para os casos com o tubo longo, o uso da barreira torna o escoamento predominantemente ascendente eliminando o curto-circuito e favorável a remoção de inclusões passando de 29,76 para 24,29% de inclusões passantes pelo veio. Enquanto que para os casos sem tubo longo, o uso da barreira proposta diminuiu o contato do aço com a escória sobrenadante, aumentou o curto-circuito e aumentou também o percentual de inclusões passantes pelo veio de 2,56 para 3,01%.

Aug 8, 2018

By Patrícia Freitas Rodrigues, Talita Gama de Sousa, Paulo Inforçatti Netto, Danilo Abílio Correa Gonçalves, Rebeca Vieira de Oliveira, Eduardo Hoisler Sallet, Jorge Vicente Lopes da Silva, Naiara Vieira Le Sénéchal, Rodolfo da Silva Teixeira, Andersan dos Santos Paula

O processo de fusão seletiva a laser (FSL) é comumente utilizado na manufatura aditiva de materiais metálicos, sendo este um processo rápido no qual as peças são formadas camada por camada. Neste processo uma fonte de laser varre o leito de pó e seleciona as regiões a serem fundidas, através da alta intensidade de potência aplicada, de acordo com o projeto digital proposto, para obter peças com boa densidade. Embora a FSL apresente diversas vantagens, em relação aos processos de fabricação convencionais, esta ainda é de alto custo para indústria. A otimização de parâmetros de processamento desta tecnologia para as ligas com memória de forma vem sendo explorada. As ligas NiTi com memória de forma se destacam por apresentarem o efeito memória de forma e a superelasticidade, o que lhe confere várias aplicações práticas. Otimizar, no processo da FSL para essas ligas, o parâmetro densidade de energia do laser, é fundamental para obter as peças com boas propriedades mecânicas e baixa porosidade. Com isso, este trabalho tem como objetivo observar e criticar a influência dos parâmetros de processamento na microestrutura e porosidade dos corpos de prova de ligas de NiTi manufaturados via FSL.

Nov 15, 2019

By Rodolfo Dal Alva Pinto

Uma linha contínua não só melhora o conforto aos usuários, mas também melhora as condições de desgaste, fadiga e manutenção dos equipamentos ferroviários. Porém os parâmetros de soldagem devem ser bem especificados e controlados de forma a obter uma junta soldada adequada. Neste trabalho foi desenvolvida a avaliação do desempenho da soldagem aluminotérmicas de trilhos. Os resultados obtidos foram empregados em ações de melhoria da qualidade da soldagem aluminotérmica, conforme relatado em outro trabalho apresentado neste evento.

Aug 16, 2017

By Allison de Sá Barreto Ferreira

O objetivo deste trabalho consiste em estudar o perfil térmico da carcaça metálica inferior do Forno Elétrico a Arco (FEA) durante o processo de produção de aço, sugerindo adição de aletas na geometria a fim de obter maior troca de calor e diminuição na temperatura de trabalho da carcaça metálica inferior do FEA. Assim, analisou-se a influência do ciclo térmico do processo por meio de acompanhamento termográfico e simulações computacionais via Método de Elementos Finitos. Posto isto, as modificações propostas, depois de testadas e analisadas por meio de um acompanhamento termográfico, denotaram eficiência de tal maneira que resultou em uma diminuição de aproximadamente 60ºC da temperatura na carcaça metálica inferior do FEA.

Oct 30, 2017

By Marcella Gautê Cavalcante Xavier

A presente proposta tem por objetivo desenvolver uma análise experimental da liga hipereutética Sn-0,5%Ni solidificada unidirecionalmente em regime transitório de fluxo de calor contra chapa molde de cobre. A liga foi avaliada quanto a sua microestrutura bruta de fusão e suas respectivas correlações com os parâmetros térmicos (velocidade da frente eutética -VE e taxa de resfriamento eutética -?E) e propriedades mecânicas. Os resultados mostram que a morfologia microestrutural predominante é composta por células ricas em estanho (β-Sn) circundadas por mistura eutética Sn+intermetálico tipo NiSn. Uma transição microestrutural foi observada entre as posições 15mm (?E=1,7°C/s) e 30mm (?E=1,1°C/s), de célula regular (CR)?célula tipo placa (CTP). Notou-se ainda a presença de intermetálicos primários NiSn distribuídos ao longo da matriz nas posições iniciais do lingote. Valores superiores de limite de resistência à tração (σu=26 MPa) e limite de escoamento (σy=21 MPa) foram encontrados para a posição 6mm a partir da base refrigerada do lingote, podendo estar relacionados com a estrutura celular mais refinada e também com a presença dos intermetálicos primários NiSn. O alongamento específico (?) comportou-se de maneira inversa, visto que as estruturas mais grosseiras (CTP) e a ausência de intermetálicos primários são responsáveis por facilitar a deformação plástica na estrutura da liga Sn-0,5%Ni, aumentando seu nível de ductilidade.

Oct 30, 2017

By Francisco Alberto Marreiros da Rocha Filho

No processo de laminação a quente ocorre ocasionalmente a perda de ductilidade a quente que pode causar o fenômeno denominado como “abertura de cabeça” da barra durante a sequência de passes. Essa perda de ductilidade a quente pode ser severa e causar interrupções no processo produtivo. Esse fenômeno pode estar associado a diversos fatores entre eles: composição química do aço; defeitos presentes no tarugo; condições do processo de laminação; e temperatura do aço durante o processo, principalmente nos passes de desbaste e intermediários de laminação. No processo em estudo, a perda de ductilidade a quente ocorre associada à laminação de vergalhões a partir de tarugos oriundos diretamente do lingotamento contínuo. O presente trabalho tem como objetivo avaliar a influência da temperatura e da microestrutura formada ao longo do processo na perda de ductilidade a quente das barras através de um exame comparativo entre os vergalhões laminados com e sem o uso da etapa de reaquecimento.

Oct 30, 2017

By Josiane Fernandes de Souza

O desenvolvimento deste trabalho refere-se ao estudo da resistência à adesão de camadas aspergidas termicamente e a quantificação, análise e a influência da presença de poros na microdureza, rugosidade e resistência ao desgaste das camadas produzidas. O método de aplicação das camadas produzidas por aspersão térmica foi o HVOF (High Velocity Oxi-Fuel) em substrato de aço SAE 1020. Observou-se que a composição química da camada produzida por aspersão térmica influenciou significativamente na dureza e resistência ao desgaste dos materiais estudados. Percebeu-se que a rugosidade variou de acordo com a preparação superficial do substrato e que a resistência à adesão foi maior para os materiais que possuem maior dureza. A porosidade não influenciou a resistência à adesão das camadas aspergidas.

Aug 7, 2018

By Anderson Azevedo Agra

O Pó de Aciaria Elétrica (PAE) é um resíduo sólido gerado durante a fabricação de aços em usinas com Forno Elétrico a Arco (FEA). Esse resíduo contem quantidades apreciáveis de metais, tais como ferro e zinco, tornando sua reciclagem interessante não só do ponto de vista ambiental como econômico. Assim, esse trabalho teve como objetivo avaliar a autorredução de misturas de pó de aciaria elétrica e coque verde de petróleo (CVP). Para isso, misturas e pelotas de PAE:CVP, com variados teores de redutor, foram submetidas a ensaios de autorredução em termobalança e, na forma de pelotas autorredutoras, numa retorta aquecida em forno elétrico vertical. A redução das amostras foi analisada a partir da perda de massa das misturas. Além disso, a redução das pelotas autorredutoras foi observada através de análises de difração de raios X. Nestas análises foi possível verificar decomposição da Franklinita e a redução dos óxidos de Ferro e Zinco.

Aug 17, 2017

By Elione Moura Carlos

O objetivo principal deste trabalho foi incorporar o resíduo de mármore no desenvolvimento de formulações de massas cerâmicas para obtenção de grês porcelanato. Foram preparadas quatro formulações da massa cerâmica variando-se as proporções de caulim, talco, feldspato, argila de queima clara e do resíduo de mármore nas misturas. Essas matérias-primas foram peneiradas na malha 200 mesh e as porcentagens para cada formulação foi misturada em moinho de bolas por 30 min. Os corpos de prova foram preparados em uma prensa uniaxial com pressão de 25 MPa e sinterizados em forno convencional nas temperaturas de 800°C, 900°C e 1.000°C, com patamar de 60 minutos e taxa de aquecimento de 10°C por minuto, verificando as propriedades das peças. Para obtenção de resultados foram realizados ensaios de absorção de água, retração linear nas peças sinterizadas, massa específica aparente e porosidade aparente, com o propósito de avaliar a variação de retração linear em determinada temperatura de acordo com a porcentagem de absorção de água. Foram realizados também os ensaios de flexão e microscopia eletrônica de varredura - (MEV). As composições estudadas apresentaram resultados satisfatórios dentro dos valores aceitáveis para o devido uso na indústria cerâmica.

Aug 7, 2018

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador is a surface deposit enriched in the highly sought after heavy rare earth elements. Early metallurgical work investigated beneficiation of the rare earth content of the Foxtrot resource using flotation, gravity separation and magnetic separation. The concentrate was then processed by acid baking and water leaching to produce a REE leachate for purification and recovery. The Search Minerals Direct Extraction Process was developed through bypassing the beneficiation process and directly acid treating a coarse crushed ore material prior to water leaching. The result is a simple, low risk technical process for direct recovery. Concurrently, the treatment of the water leach solution was modified to produce a high grade (98.9% total rare earth oxide) product for refining.

Jan 1, 2016

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By J Coveney, A Rich, D Grimsey, J Wood, S Creedy

In 2021, BHP and Metso examined processing of high-MgO nickel sulfide concentrates using Metso’s Ausmelt Top-Submerged-Lance (TSL) technology. Test work was conducted in Metso’s pilot test work facility in Dandenong, Australia to explore operability of the SiO2-FeO-MgO-CaO-NiO slag system across a wide range of compositions, temperatures and bath oxygen potentials. Pilot-scale testing aimed to define slag ‘operability limits’, representing the lowest bath temperature at which stable process and equipment operation could be maintained. This work was supported by FactSage™, version 8.2 (by Thermfact/CRCT and GTT-Technologies) thermodynamic modelling, slag viscosity measurements, physical characterisation of quenched slag samples performed by the University of Queensland and benchmarking of commercial-scale TSL nickel smelting operations. A wide range of slag compositions were examined, with Fe/SiO2 ratios varying from 0.4–1.1, CaO content from 0.8–7.0 wt per cent and MgO content from 6–19 wt per cent. Slag SiO2/MgO ratio, wt per cent CaO and matte grade were found to have the greatest impacts on identified operability limits. Operability limits were found to be influenced by both the solids content in slag and viscosity of the remaining liquid slag phase, with the relative contribution of these parameters heavily influenced by the slag composition. In the majority of trials, limits were defined by a theoretical solids content of 40–50 per cent, however in trials with a low Fe/SiO2 ratio and/or low wt per cent CaO, limits were characterised by a much lower solids content due to the increased effect of the liquid slag viscosity in determining the behaviour of these slags. The test work highlighted inherent flexibility of the Ausmelt TSL process to operate across a wide slag range of slag compositions and recover from process disturbances without an interruption to feeding. The trials also demonstrated the possibility for Ausmelt TSL technology to process concentrates with an Fe/MgO ratio as low as 1.4, which has important implications to the commercial-scale processing of high MgO feeds. Arsenic rejection across the trials was very good, with only 30 per cent of arsenic in the feed inputs reporting to the matte phase. Such high levels of arsenic removal provide the Ausmelt TSL process with a notable advantage over alternative smelting technologies.

Aug 21, 2024

By S K. Michelic, N Preisser

For certain applications, steels have to feature a very distinct and well-defined level of cleanness in terms of the number and composition of non-metallic inclusions. Therefore, one crucial aspect of steelmaking is removing and controlling said non-metallic inclusions during the process. Particle removal during ladle refining comprises three stages, namely: 1. Flotation 2. Transport through the steel/slag interface 3. Dissolution of the particle in the slag. Only if all three stages are completed the particle can be considered as fully removed from the steel melt which, in turn, leads to the slag being one of the most influential parameters for inclusion removal and control. Depending on the composition of the particles and the slag, the dissolution can be controlled by different mechanisms. This study focuses on the diffusion-controlled dissolution of solid oxidic particles in slags. For this, a model of particle dissolution has been developed. For modelling diffusion, either the differential equation following Fick’s second law can be solved, or an analytical solution to this equation valid for stationary interfaces can be used. Both approaches allow for calculations of concentration profiles of the dissolving species in surrounding slag. From this, the mass flux can be derived, which finally leads to calculating the boundary layer velocity due to considerations of mass balance. In this work, both methods as well as results of dissolution experiments using High Temperature Confocal Scanning Laser Microscopy are compared. This research aims to provide a framework for diffusion-based dissolution modelling in further expanding the understanding of particle dissolution in secondary metallurgy.

Aug 21, 2024

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By F. Robertson Jones

IF the tendency toward extending the scope of the workmen's compensation system to include life, health, accident, old age, and unemployment insurance for workers is not promptly altered, I believe there will be a complete breakdown of that system. This is not because of any objections, there may he to requiring industries to provide these additional forms of protection in whole or in part to their employees. It is rather because our workmen's compensation laws, their scale of benefits, and the administrative procedure under them are not adapted or suited to such situations. If the compensation principle is limited to its own proper sphere and is not enlarged so as to include all the ills that the flesh is heir to, it is practical, "workable, and beneficent. If it invades foreign realms, it is bound to grow into a veritable Frankenstein' which will harm principally those it 'is supposed to aid, and, at the same time, will promote waste, fraud, and Industrial demoralization. Compensation risks will become almost uninsurable; the cost to business will be intolerable; and the development of sound relief measures which will give to labor the protection now sought by the uneconomic device of enlarging the compensation law territory will be retarded.

Jan 1, 1934

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is, relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.1 Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.2 Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general; development of the area was slow. To the south, the heavy. mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions.3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west. of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of-the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.2,3 The axis of the syncline dips to thee southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.4 Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary, band of secondary clays found intermittently, at points, across the, south of the province where glacial action did not disturb or remove them.8 In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to. 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.9 It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1952